Subscribe to Our Youtube Channel
Related Manuals for Planet HDP-1261PT
Summary of Contents for Planet HDP-1261PT
- Page 1 1080p SIP Vandalproof Door Phone with RFID and PoE HDP-1261PT/HDP-5261PT Quick Installation Guide...
-
Page 2: Table Of Contents
Table of Contents 1. Package Contents ..................3 2. Physical Specifications ..................4 2.1 Wall-mounted Kit ..................4 3. Product Appearance Descriptions ..............5 3.1 Panel ..................... 5 3.2 Interface ....................6 3.3 Wiring Instructions: ................7 4. Wall-mount Installation .................. 8 5. -
Page 3: Package Contents
1. Package Contents Thank you for purchasing PLANET SIP Vandalproof Door Phone. Open the box of the SIP Vandalproof Door Phone and carefully unpack it. The box should contain the following items: Quick Installation Guide QR Code SIP Vandalproof Door Phone x 1 Sheet x 1 Let’s get started with your PLANET product... -
Page 4: Physical Specifications
2. Physical Specifications Model Dimensions HDP-1261PT 88 x 36.15 x 177.4 mm HDP-5261PT 2.1 Wall-mounted Kit 8 CM Hole 1 Hole 1 Hole 3 Hole3 Hole3 Hole 1.Custom wall hanging Hole 2.86 Box Hole 3.Gang-BOX Hole 2 Hole 2 Hole3 Hole3 Hole 3... -
Page 5: Product Appearance Descriptions
3. Product Appearance Descriptions 3.1 Panel Camera Photoresistor IR LED ToF sensor DSS Key Speaker RFID area Camera Photoresistor IR LED ToF sensor Dialing Key DSS Key Speaker RFID area... -
Page 6: Interface
3.2 Interface Open the rear case of the device where there is a row of terminal blocks for connecting power supply, electric lock control, etc. The connection is as follows: Item Description 10/100M adaptive RJ45 interface (It is ... -
Page 7: Wiring Instructions
3.3 Wiring Instructions: NO: Normally Open Contact; COM: Common Contact; NC: Normally Close Contact. Driving mode Electric-lock Mode Connections No electricity Electrify Passive when open when open S-I S-O NC COM NO √ √ √ Electric lock (normally open type) No electricity when open the door S-I S-O NC COM NO √... -
Page 8: Wall-Mount Installation
4. Wall-mount Installation Figure 4-1: Three Major Parts of HDP-1261PT or HDP-5261PT (Main Body, Back Shell and Wall Bracket) Step 1: Installation preparation A. Check the following contents: z φ 5.2 x φ3 x 6mm screws x 3 z TA4 x 30mm screws x 5 z φ 6 x 30mm screw anchors x 5... - Page 9 A. Detach the wall bracket downward from the device and loosen the four screws on the rear cover with a screwdriver, as shown in Figures 4-3-a and 4-3-b. (The installation method of the HDP-5261PT is the same as that of the HDP-1261PT. The illustration uses the HDP-1261PT as a reference.)
- Page 10 Step 4: Install the wall bracket, wiring and casing A. Align the screw holes of the wall bracket with the holes in the wall and fix them to the wall with the screws, as shown in Figure 4-4. B. Pass all the wires through the silicone plug in the middle of the bottom case. The length of all the lines should be 15 to 20 cm, as shown in Figure 4-5.
- Page 11 F. Attach the device to the wall bracket in a top-down manner, locking the screws at the Bottom, as shown in Figure 4-6. (The installation method of the HDP-5261PT is the same as that of the HDP-1261PT. The illustration uses the HDP-1261PT as a reference.)
-
Page 12: Searching Door Phone
5. Searching Door Phone There are two methods as shown below to search the HDP-1261PT and HDP-5261PT. The following operating procedures for the HDP-5261PT are the same as those of the HDP-1261PT. The HDP-1261PT is used as the representative for explanation. Method 1: Open the Planet SmartDiscoveryLite Utility. - Page 13 Restore to Default z HDP-1261PT: When the HDP-1261PT is powered on and the DSS button indicator is rapidly flashing, press the DSS button once to enter the POST mode. Then press the speed-dial button for three times for the system to reset to default and automatically announce the IP address by voice after successfully switching to the network mode.
-
Page 14: Starting Web Management And Door Phone Setting
6. Starting Web Management and Door Phone Setting Step 1: Log in to the web setting page of door phone Enter the IP address of the door phone (e.g., https://172.16.0.1) in the address bar using the https method of your PC's web browser The default user name and password are admin and 123, respectively After logging in, you will be required to change the password. - Page 15 Step 3: Setting DSS key Set the DSS key as shown below for a quick start. Click “Apply” to save this setting. Type: Memory Key. Value: The DSS Key will dial to this value. +: If value is unavailable, it will be forwarded to another value. Line: Working line.
-
Page 16: Door Unlocking Setting
7. Door Unlocking Setting RFID Card Step 1: Access control settings on web page EGS Setting Add Card Rule Select “Type” ("Normal" card provides door opening function, "Add" card and "Del" card provides add and delete card function, Default "Normal" card) Step 2: Enter your name and card number (just enter the first 10 digits of the card number), and click "Add"... - Page 17 Remote Password Step 1: Set access control on the web page EGS Setting Password Add password rule Select “Remote”. Step 2: Enter the Name, Password and Number. Press Add to Password Table. Step 3: The owner answers the access control call and presses “*” (default password) or “123456”...
-
Page 18: Customer Support
Thank you for purchasing PLANET products. You can browse our online FAQs resource and User’s Manual on PLANET Web site first to check if it could solve your issue. If you need more support information, please contact PLANET VoIP support team.
Need help?
Do you have a question about the HDP-1261PT and is the answer not in the manual?
Questions and answers