Table of Contents
Advertisement
Quick Links
Download this manual
See also:
User Manual
Advertisement
Table of Contents
Related Manuals for Planet HDP-5240PT
Summary of Contents for Planet HDP-5240PT
- Page 1 720p SIP Multi-unit Video Door Phone with RFID and PoE HDP-5240PT Quick Installation Guide...
-
Page 2: Table Of Contents
Table of Contents 1. Package Contents................3 2. Physical Specifications ..............4 2.1 Front Panel ................4 2.2 I/O Control Description ..............6 3. Installation ..................10 4. Searching Door Phone IP Address............15 5. SIP Door Phone Setting ..............16 6. Door Unlocking Setting ..............18 7. Customer Support ................22... -
Page 3: Package Contents
1. Package Contents Thank you for choosing PLANET HDP-5240PT. Before installing the door phone, please verify the contents inside the package box. The package should contain the following items: The Multi-unit Door Phone Quick Installation Guide Screw Kit RFID Card x 3... -
Page 4: Physical Specifications
2. Physical Specifications Dimensions (W x D x H) 160 x 93 x 35 mm Weight 330g (gross weight) 2.1 Front Panel Camera RFID Reader Lock Status Call and Ring Status Network and Registration Status Numeric Keypad (password or dialing) Speaker DSS Key with LED Interface Description The door phone has a built-in IP camera supporting a... - Page 5 Button Definition Button Description It can be set with a variety of functions in order Programmable Keys to meet the needs of different occasions Numeric Keyboard Input password to open the door or calls. LED Definition Status Description Steady Blue Door unlocking Door locking Lock...
-
Page 6: I/O Control Description
2.2 I/O Control Description After removing the front panel of HDP-5240PT, there are two terminal block connectors for power connection and digital I/O connections as shown in the picture below. Network port JP1 Jumper Power and lock connector Power Connector The HDP-5240PT requires either IEEE 802.3af/at PoE or DC power from... - Page 7 Power and Electric-lock Connector +DC 12V S-IN S-OUT 12V DC Input Electric-lock switch Indoor switch JP1 Jumper There are two modes for power supply of electric-lock as shown in the picture below. (The default is “Active Mode”). Passive Mode: When the electric-lock starting current is more than 12V/1000mA, the external drive mode, the electric lock interface for short circuit output control, is used.
- Page 8 Driving Mode Electric-lock Mode Connections Electrify Jumper Graphs Active Passive electricity when Active when open open Please refer to √ √ the Graph 1 in the next page Please refer to √ √ the Graph 2 in the next page Please refer to √...
- Page 9 Graph 1 Graph 2 Graph 4 Graph 3 Graph 5...
-
Page 10: Installation
The HDP-5240PT is constructed of four parts as shown below. Prior to the installation, the installer is required to remove the front panel of the HDP-5240PT for wall mounting. Please follow the steps below for the installation. Figure 1 Three Major Parts of HDP-5240PT Step 1: Installation preparation A. - Page 11 Step 2: Drilling Figure 2 Wall Mounting A. Place the mounting template with dimensions on the surface of a wall in a desired flat position. B. Use an electric drill to drill the 4 holes marked on the mounting template. It is recommended to drill about 30mm deep. Remove the template when finishing drilling.
- Page 12 B. With Phillips screwdriver, unpack the Back Panel and the main part of intercom as shown in Figure 5. Figure 5 Step 4: Hanging Shell Fixing and Cabling Figure 6 A. Select the hole for cable supply; cable length of 15cm to 20cm is recommended.
- Page 13 Step 5: Connection Line Figure 7 Figure 8 A. Select the hole for cable supply. B. Connect the cables of RJ45, power, and electric-lock to the motherboard socket as mentioned in connectors description (refer to Section 2). C. Test whether there is electricity by doing the following: 1.
- Page 14 Step 6: Mounting Figure 9 Figure 10 A. Use the 4 screws to tighten the main part of intercom on the back panel as shown in Figure 9. B. Push the device into the wall-mounted hanging shell and tighten it with 1 screw as shown in Figure 10.
-
Page 15: Searching Door Phone Ip Address
4. Searching Door Phone IP Address There are two methods as shown below to search the HDP-5240P. Method 1: Open the Planet Door Phone Finder Utility. Press the Refresh button to search the HDP-5240PT and find the IP address. Method 2: Press and hold the “#” key for 3 seconds and the door phone will report the IP address by voice. -
Page 16: Sip Door Phone Setting
5. SIP Door Phone Setting Please refer to the following steps to set the SIP door phone. Step 1: Login the homepage of the HDP-5240PT. Step 2: Add the SIP account. Set SIP server address, port, user name, password and SIP user with assigned SIP account parameters. - Page 17 Type: Hot Key Number 1: The DSS Key will dial to this Number 1. Number 2: If Number 1 is unavailable, it will be forwarded to Number 2. Line: Working line Subtype: Speed dial Step 4: Door Phone Setting...
-
Page 18: Door Unlocking Setting
6. Door Unlocking Setting Local Local Password Step 1: Go to Features Advanced Settings Set Local Password (The default is “6789”). Step 2: Use the device’s Numeric Keyboard to input password and “#” key, and then the door will be unlocked. - Page 19 Private Access Code Step 1: Go to RFID Cards Access Code Action select Remote call and Local Auth. Step 2: Use the device’s Numeric Keyboard to input password and “#” key, and then the door will be unlocked.
- Page 20 Remote Remote Password Step 1: Go to Features Advanced Settings Set Remote Password (The default is “*”). Step 2: To answer the call made by visitor via SIP phone, press the “*” key to unlock the door the visitor.
- Page 21 RFID Card Step 1: Go to RFID Cards RFID Access Enter the ID of RFID card (Only Front 10 yards) Press Add to Door Card Table. Step 2: Use pre assigned RFID cards to unlock the door by touching RFID area of device.
-
Page 22: Customer Support
7. Customer Support Thank you for purchasing PLANET products. You can browse our online FAQ resource and User’s Manual on PLANET Web site first to check if it could solve your issue. If you need more support information, please contact PLANET Home Automation support team.