Electrolux N7E Installation And Operating Manual
Pasta cooker
Hide thumbs
Also See for N7E:
- Installation and operating manual (32 pages) ,
- Installation and operating manual (30 pages) ,
- Installation and operating manual (28 pages)
Related Manuals for Electrolux N7E
Summary of Contents for Electrolux N7E
- Page 1 Pasta Cooker N7E / N9E Installation and operating manual * 59589FN01- 2025.03 *Original instructions...
- Page 2 Foreword Read the following instructions, including the warranty terms before installing and using the appliance. Visit our website www.electroluxprofessional.com and open the Support section to: Register your product Get hints & tips of your product, service and repair information The installation, use and maintenance manual (hereinafter Manual) provides the user with information necessary for correct and safe use of the appliance.
-
Page 3: Table Of Contents
B WARRANTY TERMS AND EXCLUSIONS....................10 C TECHNICAL DATA ..........................11 Dataplate position........................11 Appliance and manufacturer's identification data ................11 N7E - Gas models ........................12 N7E - Electrical models........................ 12 N9E - Gas models ........................12 N9E - Electrical models........................ 12 D GENERAL INFORMATION ........................ - Page 4 F NORMAL APPLIANCE USE ........................20 Characteristics of personnel enabled to operate on the appliance ............20 Basic requirements for appliance use....................20 G INSTRUCTION FOR THE USER......................20 General precautions........................20 Water filling ..........................21 Gas models..........................21 Electric models .......................... 21 At the end of work ........................
-
Page 5: Awarning And Safety Information
WARNING AND SAFETY INFORMATION General information To ensure safe use of the appliance and a proper understanding of the manual it is necessary to be familiar with the terms and typographical conventions used in the documentation. The following symbols are used in the manual to indicate and identify the various types of hazards: WARNING Danger for the health and safety of operators. -
Page 6: General Safety
Stage Protective Safety footwear Gloves Glasses Safety helmet garments ○ ● ○ ○ — Dismantling ○ ● ○ ○ — Scrapping Key: ● PPE REQUIRED ○ PPE AVAILABLE OR TO BE USED IF NECESSARY — PPE NOT REQUIRED During these operations, gloves must be cut-resistant. Failure to use the personal protection equipment by operators, specialized personnel or users can involve exposure to harm to health (depending on the model). -
Page 7: Safety Signs To Be Placed On The Appliance Or Near Its Area
Safety signs to be placed on the appliance or near its area Prohibition Meaning do not remove the safety devices do not use water to extinguish fires (placed on electrical parts) Keep the area around the appliance clear and free from combustible materials. Do not keep flammable materials in the vicinity of the appliance Danger Meaning... -
Page 8: Installation And Assembly
Residual risk Description of hazardous situation Tipping of loads When handling the appliance or the packing containing it, using unsuitable lifting systems or accessories or with the unbalanced load Chemical Contact with chemical substances (e.g. detergent, rinse aid, scale remover, etc.) without taking adequate safety precautions. -
Page 9: Preventive Maintenance
A.14 Preventive Maintenance In order to ensure the safety and performance of your equipment, it is recommended that service is undertaken by Electrolux Professional SpA authorised engineers every 12 months, in accordance with Electrolux Professional SpA Service Manuals. Please contact your local Electrolux Professional SpA Service Centre for further details. -
Page 10: Appliance Disposal
• replacement of light bulbs, filters or any consumable parts; • any accessories and software not approved or specified by Electrolux Professional. Electrolux Professional warranty will be void and manufacturer shall have no liability related thereto in case of any modification of the product or related hardware/software/programming. -
Page 11: Ctechnical Data
TECHNICAL DATA Dataplate position IMPORTANT This instruction manual contains information relevant to various appliances. See the dataplate located under the control panel to identify the appliance (see picture below). IMPORTANT When installing the appliance, make sure the electrical connection is carried out in compliance with that specified on the dataplate. -
Page 12: N7E - Gas Models
IMPORTANT The pilot power is less than 0.25 kW. IMPORTANT For gas pressure and consumption refer to the data plate of your appliance, or the appendix. N7E - Gas models Tank capacity Connection ISO 7/1 Minimum power Nominal heat output... -
Page 13: Testing And Inspection
Manufacturer Electrolux Professional SpA or any other D.10 Customer packaging checks service centre authorised by Electrolux Professional SpA. • The forwarder is responsible for the goods during transport and delivery. -
Page 14: Einstallation And Assembly
INSTALLATION AND ASSEMBLY Introduction 2. Remove the fixing screw nearest the control panel, from each side to be joined (Fig.1B); WARNING 3. Bring the appliances together and turn the feet to level them until the tops match (Fig.1D); Refer to “Warning and Safety 4. -
Page 15: Gas Connections
• 2.65 KPa for Propane gas. 2. Remove the plastic cap protection (if present) from the gas manifold before connecting. Models N7E 3. Countertop models can be connected to the gas supply • 1.0 KPa for Natural gas also using the rear connection:... -
Page 16: Conversion To Another Type Of Gas
E.6.6 Conversion to another type of gas The primary air is correctly adjusted when the flame does not float with the burner cold and there is no flareback with the Nozzle Table “B“ (see Appendix) gives the type of nozzles to burner hot. -
Page 17: Replacing The Adjustment Spring Of The Pressure Regulator (Only For Australia)
Replacing the adjustment spring of the 8. Prior to operation, test the gas pressure regulator for leaks. pressure regulator (Only for Australia) To replace the spring “D“ of the pressure regulator with one suitable for the gas pressure type indicated in table “B“ (see Appendix) proceed as follows: 1. -
Page 18: Electrical Connections
For the correct size of the switch, refer to the absorbed current specified on the appliance dataplate. E.10.1 Electric appliances N7E / N9E 1. Open the module door to access the terminal board (see detail 1 — Fig. 5). Fig. 5 Fig. -
Page 19: Power Cable
6. Secure the power cable with the cable clamp. 7. Refit the protection panel into its seat. N7E with electronic control In these models the power cable is already connected to the terminal block by factory setting (see Fig. 9 and Fig. 10). -
Page 20: Equipotential Node And Earth Connection
E.13 Equipotential node and Earth E.15 Water connection connection IMPORTANT Connect the appliance to an earth; it must be included in an • Carry out the water connection by referring to equipotential node by means of the screw located under the paragraph A.10 Water connection. -
Page 21: Water Filling
Water filling 4. With the pilot flame lit: • Turn knob “C“ to “Max flame“ position. 5. When the water in the tank is boiling: • Add salt, (only use pan salt, to avoid corrosive deposits on the tank bottom; if only coarse salt is available dissolve it in a separate container);... -
Page 22: At The End Of Work
CAUTION Switching off It is advisable to carry out this operation See fig. 13. after the appliance has cooled (the inertia • Turn the control knob to “0“ to switch the appliance off. of heating, even if deactivated, can damage the tank if without water). At the end of work If this is not possible, fill the tank with cold •... -
Page 23: Assign Programs To Lifter
2. Push buttons “INC/DEC“ to increase/decrease the time • Always wait the water cools down till 60 ℃ before emptying (with steeps of 5 seconds) from 15 seconds up to 20 the tank. minutes of cooking time. • Empty the tank by operating on the knob “S“ of the draining 3. -
Page 24: Maintenance Intervals
Maintenance intervals It is advisable to carry out the checks with the frequency given in the following table: Maintenance, inspections, checks and Frequency Responsability cleaning Ordinary cleaning • Daily • Operator • general cleaning of appliance and surrounding area Mechanical protection devices •... -
Page 25: Scale
For service and spare parts, please contact: • Electrolux Professional Australia PTY LTD - Suite 304, 44 Lakeview Drive Scoresby, VIC 3179. PHONE: 1300 368 299 • Zanussi - Luus Industries – 250 Fairbairn Rd, Sunshine West Victoria, 3020 – Call (03) 9240 6822 – Website: www.luus.com.au H.10 Troubleshooting... - Page 26 NOTE! Depending on the model, the doors must be removed before When dismantling the appliance, any marking, this dismantling the appliance. manual and other documents concerning the appli- ance must be destroyed. The symbol on the product indicates that this product should not be treated as domestic waste, but must be correctly disposed of in order to prevent any negative consequences...
- Page 28 Electrolux Professional SPA Viale Treviso 15 33170 Pordenone www.electroluxprofessional.com...
Need help?
Do you have a question about the N7E and is the answer not in the manual?
Questions and answers