10.4 Connection to Gen 3 Wall Mounted Indoor Units 10.5 Connection to Gen4 One-Way Cassette, Four-Way Cassette & Concealed Ducted Indoor Units 10.5.1 Connecting One Thermostat 10.5.2 Connecting Two Thermostats 10.5.3 Connecting Multiple Indoor Models 10.5.4 Thermostat Connection Detail Climate 5000 Series Gen 4 Wired Wall Thermostat (02.2025)
Page 4
11.15.2 Starting Saved 7-Day Schedule 11.15.3 Set Day Off (Holiday) 11.16 Copy Existing Schedule 11.17 Delete Saved Schedule 11.18 Set Timer On or Off Function 11.19 Set Timer On and Off Function Climate 5000 Series Gen 4 Wired Wall Thermostat (02.2025)
WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury. CAUTION CAUTION indicates a hazardous situation which, if not avoided, could result in minor to moderate injury. NOTICE NOTICE is used to address practices not related to personal injury. Climate 5000 Series Gen 4 Wired Wall Thermostat (02.2025)
Page 6
KEEP new and used batteries OUT OF REACH of CHILDREN • Seek immediate medical attention if a battery is suspected to be swallowed or inserted inside any part of the body. Climate 5000 Series Gen 4 Wired Wall Thermostat (02.2025)
Page 7
• Always completely secure the battery compartment. If the battery compartment does not close securely, stop using the product, remove the batteries, and keep them away from children. Climate 5000 Series Gen 4 Wired Wall Thermostat (02.2025)
The Wired Wall Thermostat can be used with multiple indoor units provided they are all the same indoor unit type. The Wired wall thermostat does not have wireless function. Climate 5000 Series Gen 4 Wired Wall Thermostat (02.2025)
4-Core shielding wire (Cable 4) connector cable. Screw M4X8 (For Mounting the connective wire group). Apply magnetic ring to connective cabling to Magnetic ring reduce the risk of electrical interference Table 2 Climate 5000 Series Gen 4 Wired Wall Thermostat (02.2025)
MODE: Change mode of operation. FUNCTION BUTTON: To activate Turbo function or Follow Me function SWING: Adjust louver angle (Wall Mounted and Cassette type indoors only). ADJUST: Used to adjust setting 1 0 | Climate 5000 Series Gen 4 Wired Wall Thermostat (02.2025)
Page 11
10. BACK: To go back to previous page 11. DAY OFF/DELAY: Used to skip day during 7-Day scheduling or delete saved set up. 12. CHILD LOCK: To activate Child Lock function | 11 Climate 5000 Series Gen 4 Wired Wall Thermostat (02.2025)
Displays selected fan Active clean display display speed: VERTICAL SWING Intelligent eye display display Secondary unit Electric heating display HIGH display Main unit and secondary AUTO unit display Figure 3 1 2 | Climate 5000 Series Gen 4 Wired Wall Thermostat (02.2025)
Do not install the wired wall thermostat where it can be affected by: • Direct hot or cold air from ducts • Drafts or dead spots behind doors and corners • Direct sun light contact area | 13 Climate 5000 Series Gen 4 Wired Wall Thermostat (02.2025)
BMS500-XXXXXX-XXXXXD For Generation 2, model number ends with: A or B For Generation 3, model number ends with: C For Generation 4, model number ends with: D 1 4 | Climate 5000 Series Gen 4 Wired Wall Thermostat (02.2025)
Thermostat screwdriver Slots Figure 5 Pry upwards on screwdriver to remove the back cover. NOTICE Product damage! Be careful not to damage the PCB board inside with the screwdriver. | 15 Climate 5000 Series Gen 4 Wired Wall Thermostat (02.2025)
Install back plate on the wall using the 3 screws (M3.9x25) and wall anchors (where wall studs are not available). Back cover plate Screws (M3.9x25) Figure 6 NOTICE Product damage! Over-tightening screws may damage back cover plate. 1 6 | Climate 5000 Series Gen 4 Wired Wall Thermostat (02.2025)
Page 17
(secured to wall) Switch box Screw (M4x25) (secured to Back cover plate switch box) Figure 7 NOTICE Product damage! Place on a flat surface. Over-tightening screws may damage back cover plate. | 17 Climate 5000 Series Gen 4 Wired Wall Thermostat (02.2025)
For Gen 4 One-Way Cassette, Four -Way Cassette or Concealed Ducted models, the above wiring does not apply. Shielded 2-core cable (field supplied) must be used for all installations. 1 8 | Climate 5000 Series Gen 4 Wired Wall Thermostat (02.2025)
The magnetic ring may be applied to any one of the supplied or field supplied cables depending on your installation. Magnetic Ring Accessory Cable or HA/HB (Field Supplied) 2-Core Cable Figure 9 | 19 Climate 5000 Series Gen 4 Wired Wall Thermostat (02.2025)
Thermostat Cable 4 (12V/5V, E, Y, X on adapter board) Cable 2 (20ft long - Male / BROWN WHITE YELLOW Female 4-pin connector) 12V/5V CN41 CN42 Figure 10 2 0 | Climate 5000 Series Gen 4 Wired Wall Thermostat (02.2025)
Page 21
Attach 4-pin male connector wire (Cable 1) to plug connection (CN2) on wired thermostat PCB. Surface Mount Installation Switch Box Mount Installation Cable 1 Switch Back Plate Cable 1 Wiring Knockout Figure 11 Cable 1 - 4 Pin Connector Figure 12 | 21 Climate 5000 Series Gen 4 Wired Wall Thermostat (02.2025)
Page 22
Installation Instructions Reattach the wired controller to the mounted back plate. Figure 13 2 2 | Climate 5000 Series Gen 4 Wired Wall Thermostat (02.2025)
(PN:8733977006). Adapter board cable kit components: 12VDC Cable A Adapter (3-pin connector & Board 4-pin connector / 7-pin connector) Cable B (2-pin male connector) Figure 14 | 23 Climate 5000 Series Gen 4 Wired Wall Thermostat (02.2025)
Page 24
Installation Instructions Open the front panel of the Wall Mounted Unit and locate the display board bracket shown below. Remove the bracket from the units front panel. Figure 15 2 4 | Climate 5000 Series Gen 4 Wired Wall Thermostat (02.2025)
Page 25
Installation Instructions Disconnect the wire from CN1 port on the display board. Figure 16 Disconnect the wire from CN18 port on the unit’s main control board shown below. Figure 17 | 25 Climate 5000 Series Gen 4 Wired Wall Thermostat (02.2025)
Page 26
Installation Instructions Make connnections for cable A and Cable B to display and main boards Cable B Display board Main board CN18 Cable A CN32 Figure 18 2 6 | Climate 5000 Series Gen 4 Wired Wall Thermostat (02.2025)
Page 27
Place the adapter board in the location shown below. Figure 19 Make connnections to adapter board Connect to CN40 Cable B Adapter board (external accessory) CN40 Connect to CN43 Cable A CN43 Figure 20 | 27 Climate 5000 Series Gen 4 Wired Wall Thermostat (02.2025)
Page 28
Thermostat Cable 4 (12V/5V, E, Y, X on adapter board) Cable 2 (20ft long - Male / BROWN WHITE YELLOW Female 4-pin connector) 12V/5V CN41 CN42 Figure 21 2 8 | Climate 5000 Series Gen 4 Wired Wall Thermostat (02.2025)
Page 29
Cable 1 Wiring Knockout Figure 22 Attach 4-pin male connector wire (Cable 1) to plug connection (CN2) on wired thermostat PCB. Cable 1 - 4 Pin Connector Figure 23 | 29 Climate 5000 Series Gen 4 Wired Wall Thermostat (02.2025)
Page 30
Installation Instructions 10. Reattach the wired controller to the mounted back plate. Figure 24 3 0 | Climate 5000 Series Gen 4 Wired Wall Thermostat (02.2025)
Page 31
Connect shielded 2-core wiring to the terminals on the thermostat (HA, HB). See 10.5.4 Thermostat Connection Detail. Indoor Unit HA HB Wired Controller Figure 25 | 31 Climate 5000 Series Gen 4 Wired Wall Thermostat (02.2025)
Page 32
See 10.5.4 Thermostat Connection Detail. There is no polarity between HA and HB. Indoor Unit HA HB Wired Controller 1 Wired Controller 2 Figure 26 Prioritization is based on the last wired thermostat parameter setting. 3 2 | Climate 5000 Series Gen 4 Wired Wall Thermostat (02.2025)
Page 33
Indoor Unit n (n<=16) HA HB HA HB HA HB Wired Controller 1 Figure 27 Error codes will only show on the specific Indoor Unit LED where the error has occurred. | 33 Climate 5000 Series Gen 4 Wired Wall Thermostat (02.2025)
Page 34
Unit Wiring Knockout HA HB Figure 28 Connect the 2-Core Cable to terminal connection (HA, HB) on wired thermostat PCB. 2-Core Cable (field supplied) HA, HB Figure 29 3 4 | Climate 5000 Series Gen 4 Wired Wall Thermostat (02.2025)
Page 35
Installation Instructions Reattach the wired controller to the mounted back plate. Figure 30 | 35 Climate 5000 Series Gen 4 Wired Wall Thermostat (02.2025)
(4-pin connector) shielded wire Indoor Unit) (some units) Figure 31 Connect to the thermostat by routing Cable 1 through the thermostat back plate based on the mounting installation. 3 6 | Climate 5000 Series Gen 4 Wired Wall Thermostat (02.2025)
Page 37
Cable 1 Wiring Knockout Figure 32 Attach 4-pin male connector wire (Cable 1) to plug connection (CN2) on wired thermostat PCB. Cable 1 - 4 Pin Connector Figure 33 | 37 Climate 5000 Series Gen 4 Wired Wall Thermostat (02.2025)
Page 38
Installation Instructions Reattach the wired controller to the mounted back plate. Figure 34 3 8 | Climate 5000 Series Gen 4 Wired Wall Thermostat (02.2025)
Product damage! DO NOT allow water to enter the wired wall thermostat. Use the trap and putty to seal the wires. Putty Trap Putty Putty Trap Trap Figure 35 | 39 Climate 5000 Series Gen 4 Wired Wall Thermostat (02.2025)
Set the correct time before operating. Batteries in the wired controller can maintain the correct time during a power failure. When the power is restored and the displayed time is not correct, replace the battery. 4 0 | Climate 5000 Series Gen 4 Wired Wall Thermostat (02.2025)
Press repeatedly to adjust the current time in 1 minute increments. example: Monday 11:20 Figure 38 The setting is complete after pressing TIMER or the CONFIRM button. | 41 Climate 5000 Series Gen 4 Wired Wall Thermostat (02.2025)
Ensure the unit is plugged in and power is available. Press the POWER button. Press MODE button to change / select desired operation mode. Figure 39 Press buttons to set desired temperature. 4 2 | Climate 5000 Series Gen 4 Wired Wall Thermostat (02.2025)
SWING There are no symbols displayed on the LCD display when FP Freeze Protection function is enabled. Only the setting temperature will display the change to 46°F (8°C). | 43 Climate 5000 Series Gen 4 Wired Wall Thermostat (02.2025)
11.5 Change Fan Speed Press FAN button to select desired fan speed or auto speed mode. Auto HIGH Figure 41 Fan speed cannot be changed in Dry and Auto mode. 4 4 | Climate 5000 Series Gen 4 Wired Wall Thermostat (02.2025)
Indoor Unit Figure 42 By default, Follow me function in the wired thermostat will be turned on with 4-Way Cassette and Ducted Indoor models. | 45 Climate 5000 Series Gen 4 Wired Wall Thermostat (02.2025)
Funtion button to select the filter cleaning prompt icon, and press the CONFIRM button to reset the filter screen time. The filter cleaning reminder icon goes out. 4 6 | Climate 5000 Series Gen 4 Wired Wall Thermostat (02.2025)
The display will show the set temperature for 5 seconds, and then return back to the set humidity display. After switching the mode, exit the humidity control mode. | 47 Climate 5000 Series Gen 4 Wired Wall Thermostat (02.2025)
(-0 corresponds to all four louvers). Figure 43 Press the SWING button to adjust the airflow direction of the selected louver. 4 8 | Climate 5000 Series Gen 4 Wired Wall Thermostat (02.2025)
11.15.1 Programming 7-day Schedule Press TIMER button to select the Week and press CONFIRM button. Press to select the day of the week and then press CONFIRM button. Figure 44 | 49 Climate 5000 Series Gen 4 Wired Wall Thermostat (02.2025)
Page 50
WEEKLY TIMER is set according to the user’s life style. Press to set the time then press CONFIRM button. Press to set the operation mode then press CONFIRM button. Figure 46 5 0 | Climate 5000 Series Gen 4 Wired Wall Thermostat (02.2025)
Page 51
CONFIRM button. Figure 47 This setting is unavailable in the AUTO, DRY or OFF modes. Different schedules can be programmed by repeating steps 3 through 7. | 51 Climate 5000 Series Gen 4 Wired Wall Thermostat (02.2025)
To Cancel: Press POWER button for two seconds to cancel the timer mode. The timer mode can also be canceled by changing the timer mode using TIMER button. 5 2 | Climate 5000 Series Gen 4 Wired Wall Thermostat (02.2025)
To cancel, follow the same procedures used for setup. The DAY OFF (holiday) setting is cancelled automatically after the set day has passed. | 53 Climate 5000 Series Gen 4 Wired Wall Thermostat (02.2025)
Other days can be copied by repeating steps 4 and 5. Press CONFIRM button to save the settings. Press BACK button to revert to the 7-Day schedule. 5 4 | Climate 5000 Series Gen 4 Wired Wall Thermostat (02.2025)
CONFIRM button. After selecting the day to be deleted, press DAY OFF/DELAY button to delete the saved setting. ex. Delete the time scale 1 in saturday Figure 51 | 55 Climate 5000 Series Gen 4 Wired Wall Thermostat (02.2025)
After the time is set, the timer starts or stops automatically. Press CONFIRM button again to finish the settings. ex.Off timer set at 18:00 Figure 53 5 6 | Climate 5000 Series Gen 4 Wired Wall Thermostat (02.2025)
Clock display flashes. Press to set the ON timer and then press CONFIRM button. Press to set the OFF timer. press CONFIRM button again to finish the setting. | 57 Climate 5000 Series Gen 4 Wired Wall Thermostat (02.2025)
Page 58
Online Help Resources Visit our Service & Support webpage to find FAQs, videos, service bulletins, and more at http://www.bosch-homecomfort.us/service or use your cellphone to scan the code below. Figure 54 5 8 | Climate 5000 Series Gen 4 Wired Wall Thermostat (02.2025)
Page 59
Installation Instructions NOTES: | 59 Climate 5000 Series Gen 4 Wired Wall Thermostat (02.2025)
Page 60
United States and Canada Bosch Thermotechnology Corp. 65 Grove Street Watertown, MA 02472 Tel: 800-283-3787 www.bosch-homecomfort.us BTC 769203302 C / 02.2025 Bosch Thermotechnology Corp. reserves the right to make changes without notice due to continuing engineering and technological advances.
Need help?
Do you have a question about the Climate 5000 Series and is the answer not in the manual?
Questions and answers