Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Sigma EF-610 - NA-ITTL
Summary of Contents for Sigma EF-610 - NA-ITTL
- Page 1 F18N10081 E L E C T R O N I C F L A S H EF-610 DG SUPER INSTRUCTIONS NA-iTTL...
- Page 2 ENGLISH The CE Mark is a Directive conformity mark of the European Community (EC).
- Page 3 ENGLISH Thank you very much for purchasing the Sigma EF-610 DG SUPER NA-iTTL Electronic Flash. This product is specifically developed for the Nikon SLR series cameras. Depending on the camera model, functions and operation may vary. Please read this instruction booklet carefully. To add to your enjoyment of photography, this flash has a variety of features.
-
Page 4: Description Of The Parts
DESCRIPTION OF THE PARTS 1.Flash Head 2.AF Auxiliary Light 3.Bounce Angle; Up and Down 4.Bounce Angle; Right and Left 5.Bounce Lock and Release Button; Up and Down EXTERNAL 6.Swivel Lock and Release Button; Right and Left 7.LCD Panel 8.Battery Cover PARTS 9.Shoe Ring 10.Shoe... -
Page 5: Adjusting The Flash Head
3. Close the cover. 4. Slide the Power Switch to the ON position. After few seconds the Ready Lamp will light, indicating that the flash unit can be fired. 5. Please press the “Test Button” to be sure that the flash is working properly. AUTO POWER OFF To conserve battery power, the flash unit automatically turns itself off when the flash is not used within approximately 80 seconds. -
Page 6: Wide Panel
ZOOM button will not function. In this case please contact the store where the flash was purchased, or an authorized .Sigma service station. LCD PANEL ILLUMINATION When you press the LIGHT button, the LCD panel will illuminate for about 8 seconds. The illumination stays on longer than 8 seconds if you press the LIGHT button once again. - Page 7 ◆ Depending on the combination of the camera, lens and selected exposure mode, the method for shooting the subject with flash may be different. Please see chart “A” and set the “F”-number by referring to the manual for your camera. 6.
-
Page 8: Limits Of Continuous Shooting
LIMITS OF CONTINUOUS SHOOTING To prevent overheating of the flash’s circuitry, do not use your Flash unit for at least 10minutes after continiously using the flash as shown in the table below. Mode Number of Flash Exposures TTL, M(1/1,1/2) 20 Continuous Flash Shots M(1/4, 1/8) 25 Continuous Flash Shots M(1/16-1/32) -
Page 9: Exposure Compensation
When using with cameras other than the above 1.Please follow the first 2 steps as above and press the SEL button several times to make the aperture display blink. 2.Press the + button or – button to set the F-stop display. 3.Press the SEL button to stop the display blinking. -
Page 10: Rear-Curtain Synchronization
Use your camera’s exposure compensation control button or dial to make exposure compensation to both foreground and background. (Please refer to your camera’s instruction) Exposure compensation on M mode When using the camera on M mode, you can change the aperture value on the camera, or change the flash power level, after setting the exposure compensation. -
Page 11: Bounce Flash
8. Press the + or – button to set the desired number of flashes. 9. Press the SEL button until the display stops blinking. 10. When the ready light of the flash is illuminated, the unit is ready to use. Note: Please set the shutter speed longer than;... -
Page 12: Wireless Flash
WIRELESS FLASH When using the “Wireless Flash” mode, you can take pictures with a more three-dimensional feeling with shadow, or you can produce natural images with shadow depending on the flash position without any extension cord connecting the camera body to the flash. In case of the EF-610 DG SUPER NA-iTTL, communication between the camera body and the flash will be achieved by the light of the flash. -
Page 13: Slave Flash
set the required amount, then press the SEL button to set compensation. If M mode is selected, press the + or – button to set the flash output amount. If MULTI is selected, exposure will switch to Multi Flash Mode. Setting the Flash Mode on the slave flash unit The following has to be programmed into the master unit. -
Page 14: Designated Slave Flash
9. Place the slave unit in the desired location. Do not place the slave unit within the picture area. 10. After confirming that all flash units are fully charged, press the shutter button to take the picture. ◆ When the EF-610 DG SUPER NA-iTTL is fully charged, the AF Auxiliary Light will blink. ◆... -
Page 15: Specifications
SPECIFICATIONS TYPE : Clip-on type serial-controlled TTL auto zoom electric flash GUIDE NUMBER : 61 (ISO 100/m, 105mm head position) POWER SOURCE : Four AA type alkaline batteries or, Four AA type Ni-Cd batteries or, Four AA type Ni-MH Nickel-Metal Hydride RECYCLING TIME : about 7.0 sec. - Page 16 [Table1] GN (ISO100・m） 17mm 24mm 28mm 35mm 50mm 70mm 85mm 105mm 23.0 34.0 35.0 36.0 46.0 52.0 56.0 61.0 16.3 24.0 24.7 25.5 32.5 36.8 39.6 43.1 11.5 17.0 17.5 18.0 23.0 26.0 28.0 30.5 12.0 12.4 12.7 16.3 18.4 19.8 21.6 1/16...