Related Manuals for Lange Originals Hoist-A-Top JK Power
Summary of Contents for Lange Originals Hoist-A-Top JK Power
- Page 1 HOIST ® JK Power Installation Instructions langeoriginals.com Lange Originals 3651 S. 700 E. Salt Lake City, UT 801-262-7322...
- Page 2 HOIST ® PLEASE READ ALL INSTRUCTION BEFORE INSTALLATION Parts List Parts are listed by part number, description, and HAT-100 quantity. The part number may be referenced in the HAT-101 instructions designated by parenthesis () for your convenience. Parts are updated periodically and may vary in color or shape.
- Page 3 Never lift your top tight against the ceiling. This puts undue stress on the top and the hoist. Lange Originals® is not responsible for damage or personal injury due to improper installation, custom installation that doesn’t follow the instructions, or neglect.
- Page 4 Power Unit Ceiling Mount 1.) Determine a suitable lifting point: Back your Jeep in the garage to a suitable parking spot with room to open your tailgate. Run a plumb- bob from the center of your hardtop to the ceiling and mark with a pencil.
- Page 5 Fig. C Back wall or garage door Ceiling mount Power Unit with perpendicular studs Drop cable Shown as if looking up at Cribbing the ceiling with bare studs/joists Center point Center the two 2x6 ‘s with measured with Pulley cable 27"...
- Page 6 Fig. E Back wall or garage door Ceiling mount 2x6 cross brace with parallel studs laying flat on 16 Shown as if inch centers looking up at the ceiling with Drop cable bare studs/joists Install two cross braced 2x6’s between studs 27 "...
- Page 7 Power Unit Wall Mount Fig. A 1.) Determine a suitable lifting point: Back your Jeep into your garage and run a plumb-bob from the center of your hardtop to the ceiling and mark with a pencil. Draw a straight line to the wall you want your power unit on.
-
Page 8: Wall Mount
Wall Mount Install two cross braced 2x6’s between studs centered on the middle mark you drew with your pencil and plumb bob. The pulleys should be installed 32 inches apart centering the pulley wheels. Be sure to have a 1/2 inch offset on the two pulleys. Install 2x6’s with provided long screws (HAT-050). -
Page 9: Frame Assembly
HOIST ® Frame Assembly A. ocat the ide two of the support arms (HAT-101) into the T-shaped bar (HAT-100) moving the spring button to the appropriate holes as shown in Fig. 3 B. Slide the Black Foam Holes (HAT-018) on the arms (HAT-101) to protect your hardtop and freedom top pieces. The black round foam pieces should be spaced directly under your Freedom Top Panels during storage. - Page 10 JK 4 Door Setting JK 2 Door Setting JK 2 Door Setting JK 4 Door Setting Fig. 3 Front settings for JK Fig. 4 Underside placement of the rear arm JK Two Door Setting Page 9...
- Page 11 Balancing & Attaching The Frame: If you have not done so, put your safety stop loosely in place. With your frame assembled (Fig. 1-4) lay it on the floor directly below the cables with the top of the “T” Frame facing your garage door. Insert one thimble (HDW-031) on the rear most hole on the lifting blade (HAT-100).
-
Page 12: Glossary Of Terms
The documents and instructions in this product are subject to copyright ©2016 all rights reserved. Hoist A Top, Off With Your Top, Lange Originals, are registered trademarks of Lange Originals LLC. Hoist A Top, Hoist A Cart, Hoist A Top Simple, are protected by the following patents 009932209B2 Chrysler, Dodge, Jeep, Ram, Mopar and SRT are registered trademarks of FCA US LLC. - Page 13 We will respond in writing on how to proceed. Please do not contact your dealer, contact Lange Originals directly to avoid delays. Please note you will be asked to provide information such as dealer receipt/invoice and sometimes pictures of the item.
Need help?
Do you have a question about the Hoist-A-Top JK Power and is the answer not in the manual?
Questions and answers