Subscribe to Our Youtube Channel
Related Manuals for Lange Originals HOIST-A-TOP JT CRANK
Summary of Contents for Lange Originals HOIST-A-TOP JT CRANK
- Page 1 LANGE ORIGINALS HOIST-A-TOP JT CRANK Call toll free 1866 284 7428 langeoriginals.com copyright lange originals 2017...
- Page 2 Make sure all are �ght and in good working order. • Lange Originals is not responsible for damage or personal injury due to improper installa�on, custom installa�on that doesn't follow the instruc�ons, or neglect to inspect equipment prior to using equipment.
- Page 3 HOIST ® Parts List HAT-100 Parts are listed by part number, description, and quantity. The part number may be referenced in the instructions designated by parenthesis () for your convenience. Parts are updated periodically and may vary in color or shape. HAT-101 HAT-140 014-JTC Hoist-A-Top Crank for Gladiator...
- Page 4 50-inches above the floor. Mount your crank unit to the 2x6, centered with your hardtop, using both 3" lag screws and washers (HAT-054 & HAC-023) provided. Call toll free 1866 284 7428 langeoriginals.com copyright lange originals 2017...
- Page 5 & HAT-125) ½ inch le� of center on the 2x6. This will allow the second cable to run along the ceiling Garage door without interfering with the other cable. Call toll free 1866 284 7428 langeoriginals.com copyright lange originals 2017...
- Page 6 ½ inch le� of that. This will allow the cables to run next to each other without interference. Call toll free 1866 284 7428 langeoriginals.com copyright lange originals 2017...
- Page 7 This pulley is ½ inch This pulley can be installed of center. on the wall or ceiling Longer cable side of crank drum) Call toll free 1866 284 7428 langeoriginals.com copyright lange originals 2017...
- Page 8 Side wall mount option Mount your crank unit on the side wall as per the standard instructions. Figure A Mount the double pulley in the corner of the wall next to the ceiling directly above the crank unit. (Fig. A} Side wall View of 2x6 on ceiling Mount your single line...
-
Page 9: Frame Assembly
HOIST ® Frame Assembly A. Locate the metal T-Frame bundle. Slide two of the support arms (HAT-101) into the T-shaped bar (HAT-100) moving the spring button to the outermost holes as shown in Fig. 3 We will only be assembling the front portion of the T (Fig. - Page 10 JT 4 Door Setting JT 4 Door Setting Fig. 3 front settings on frame Long Foam Supports Fig. 4 Underside look at the correct place- ment of the rear arm JT 4 Door Setting...
- Page 11 Fig. 6 Showing the frame fully assembled through the rear window. Fig. 7 Depiction of the assembled rear support. Should be assembled in steps after frame is assembled and needs to be tted with care- Fig.2 Front Assembly through window. placed on Jeep before clipping in the rear assembly...
-
Page 12: Installing The Cable
A�ach the cables to the front and rear using the wire thimbles and clamps. Use the farthest back hole for the second li�ing point. See the next page for details Call toll free 1866 284 7428 langeoriginals.com copyright lange originals 2017... - Page 13 Balancing and attaching the frame With your frame assembled (Fig. 1-8) lay it on the floor directly below the cables with the top of the “T” Frame facing your garage door. Insert one thimble (HDW-031) on the rear most hole on the lifting blade (HAT-100).
-
Page 14: Glossary Of Terms
The documents and instructions in this product are subject to copyright ©2016 all rights reserved. Hoist A Top, O With Your Top, Lange Originals, are registered trademarks of Lange Originals LLC. Hoist A Top, Hoist A Cart, Hoist A Top Simple, are protected by the following patents 009932209B2 Chrysler, Dodge, Jeep, Ram, Mopar and SRT are registered trademarks of FCA US LLC.
Need help?
Do you have a question about the HOIST-A-TOP JT CRANK and is the answer not in the manual?
Questions and answers