Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Haworth Manuals
  4. Indoor Furnishing
  5. Enclose 127-8829
  6. Installation manual

Haworth Enclose 127-8829 Installation Manual

Hide thumbs

Advertisement

Quick Links

Download this manual
Enclose ®
Installation Manual – February 2024
Revision: 4
Part Number: 127-8829

Advertisement

loading
Need help?

Need help?

Do you have a question about the Enclose 127-8829 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Haworth Enclose 127-8829

Summary of Contents for Haworth Enclose 127-8829

  • Page 1 Enclose ® Installation Manual – February 2024 Revision: 4 Part Number: 127-8829...
  • Page 3 Thank you for choosing ENCLOSE by Haworth. Enclose is a non-progressive, unitized wall panel system. The order of installation should be carefully considered before the installation phase of the project begins. Before determining where to start and how to progress, it is important to clearly understand the customer expected layout regarding wall panel, door, intersection and attachment locations.
  • Page 4 Table of Contents Safety - Working with Glass - Cutting Aluminum/Plastic General Installatoin Guidelines - Tools Required - Measuring - Floor Types - Ceiling Types (Including Grid Clips) Starters & Posts Floor to Ceiling - Ceiling Track - Panel connections Freestanding &...
  • Page 5 Wood & Metal Sliding Doors c/w Soft Close Glass Slab Sliding Doors c/w Soft Close Double Glazed Sliding Doors c/w Soft Close Haworth Door Hardware -D and Bar Pulls -Lockset Patch housing and Covers Pro les - Quick Reference for Enclose Pro les...
  • Page 6 ENC® Section 1 - Safety Working with Glass When handling tempered glass use cut resistant gloves and safety glasses to protect yourself. When staging or placing glass into frames also wear glass sleeves to protect your forearms from sharp edges. all carts and staging surfaces must be padded.
  • Page 7 ENC® Section 2 - Safety Tools Required Robertson Cordless drill with #2 square recess driver bits Square Bit Hammer drill (for concrete anchors or screws) Vacuum 16 to 27 oz Deadblow Hammer Tap block Level (4’ and 2”) Laser - 5 -point Square (small) Anvil Cutters Tape Measure (Metric and Imperial)
  • Page 8 ENC is capable of, and intended, to be installed on all oor types and substrates. Due to various oor constructions, the anchoring components are not provided by Haworth. The appro- priate fastening components and frequency of attachment should be determined by the site engineer.
  • Page 9 ENC® Section 3 - Starters, Intersections, End of Run Starter Types Cat# 122-4740 Cat# 122-4739 Compressible Starter Shown with optional Adjustable Starter Low Pro le Starter 114-2202 Enc Compressible Starter Bracket Rev: 4 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 10 Starter Installation NOTES: Seismic Applications Starters must be anchored COMPRESSIBLE STARTER to the hardwall in seismic FOR DOORS/WALLS X = 12mm ±5mm (1/2" ±3/16") (P4) (P3) Reveal Connector Compressible Starter LOW PROFILE X = 31.8mm ±5mm (1 1/4" ±3/16") ADJUSTABLE X = 61mm ±12mm (2-13/32"...
  • Page 11 Post Types 122-4733 Post 135 Inner Corner Clip Inner Corner Post Clip 135° 122-4732 122-4732 Post 2 Way 90° Closed Post 2 Way 90° Open Inner Corner Post Clip 90° Inner Corner Clip 122-4734 122-4735 114-2202 Without Cutout With Cutout Compressible Starter Bracket Post Inline 6 Inches...
  • Page 12 Corner Reveal Connector Installation Cat# 114-2178 Reveal 2-Way 2-Way (90°) 2-Way (135°) Connection Connection 2-Way (90°) 2-Way (135°) 3-Way 4-Way Rev: 4 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 13 Trim Installation Install 2-way & 3-way corner trim 3-Way 2-Way Slide light block (P) down 3-Way 2-Way Rev: 4 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 14 End Of Run Installation Cat # 122-4730 Rev: 4 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 15 ENC® Section 4 - Floor To Ceiling Panels Ceiling Track Cat# 114-2179 Ceiling Track Flap Cat# 114-2180 #10-24 x 1/2" Screw Self Drilling SPACER CEILING 1/4 - 20 Hex Nut BRACKET CEILING TRACK FOAM TAPE CEILING TRACK FLAP CONNECTOR PLATE Install ceiling track ap (B) Rev: 4 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 16 Locate points onto ceiling for ceiling track (A) (LAYOUT PLAN) 1/4 - 20 Hex Nut Rev: 4 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 17 2-Way Condition Inline Condition Splice Plates Cat # 114-2194 3-Way Condition Rev: 4 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 18 Smooth Floor Attachment Smooth Shoe Cat# 114-2193 NOTE: Every 16” is for seismic conditions 16" NOTE: All product over 10-1/2’ feet will have to use the respective “shot” shoe/gripper solution for oor lateral bracing. Fastener (AD) speci ed 16" by others. NOTE: Only two smooth grippers (AB) per panel.
  • Page 19 Floor to Ceiling Panels GLASS PANELS SOLID PANELS Cat# 114-3833 Cat# 122-4741 Reveal Connector CAT # 114-2178 Y-Bolt Bracking Y-Bolt CAT # 114-2190 Panel Leveler Cover Raceway Cover Rev: 4 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 20 Install corner reveal connector (H & J) NOTE: Before installing panels install all corner reveal connectors (H & J) to all panels (A) used in corner conditions. 2-Way (90°) 2-Way (135°) Modify reveal connector (H & J) for component (K) installation NOTE: Install half reveal connector (W) as shown.
  • Page 21 Panel Installation Adjust levelers (L) to lower panel (A) Install panel (A) Raise Panel Height .75 (19mm) TO 1.25" (32mm) Rev: 4 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 22 Tile Attachment Note: Work tile attachment from the top down and be careful not to damage edges. Rev: 4 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 23 Optional - Securing to Building Cat# 114-2190 Rev: 4 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 24 ENC® Section 5 - Free Standing Panels Freestanding Splice Plates Cat# 114 Freestanding Cover Cat# 114-2196 Install panel connectors (A) cut if necessary 120" 48" (3048 mm) (1219 mm) 120" (3048 mm) 48" (1219 mm) #10 x 5/8" Self-Drilling Screw TOP VIEW TOP VIEW Rev: 4...
  • Page 25 Starter Brackets Installation Install starter bracket(s) (C & D) #10 x 5/8" Self-Drilling Screw ADJUSTABLE STARTER (C) NOTE: Remove screws that interfere with brackets. #10 x 5/8" Self-Drilling Screw LOW PROFILE STARTER (D) Rev: 4 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 26 2- Way, 3-Way & 4-Way Corner Bracket Installation Install corner bracket(s) (E,F,G & H) NOTE: Remove screws that interfere with brackets. #10 x 5/8" Self-Drilling Screw VARIABLE CORNER BRACKET (F) 2-WAY CORNER BRACKET (E) 3-WAY CORNER BRACKET (G) 4-WAY CORNER BRACKET (H) Rev: 4 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 27 2-Way, 3-Way & 4-Way Module Corner Bracket Installation Install module corner bracket(s) (J) with spacer (K) NOTE: Remove screws that interfere with brackets. 2-WAY 3-WAY #10 x 3/4" Self-Drilling Screw 4-WAY Rev: 4 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 28 Panel Brace Bracket Installation Chinook Beam Installation Angle Beam Bracket Panel Brace Backet 2" 4" 3" 2" 5" 4" 3" Panel Angle Bracket Installation NOTE: Fastener to be supplied by others. Fastener recommendation is to be veri ed with the engineer of record.
  • Page 29 Optional: Cosmetic Cap Installation Install Bracket (M) Rev: 4 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 30 Stack-on Panels Bracket and Screws Cat#121-7860 Brace Cat#121-7859 (S-93) Wafer Screw (S-108) #12-11 x 2" Pan Head Screw Rev: 4 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 31 If there is adequate space (12” recommended) on either side of the wall, you may build the wall upright and then shift it left/right into it’s nal position. If there isn’t space to shift the wall, you will have to build the wall at on the oor and then stand it into position.
  • Page 32 Cut to same length as EFG bottom horizontal rail (D) Remove the oor seals (E) from the EFG bottom horizontal rail (D) and install them in the horizontal stack rail (A) as shown. Rev: 4 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 33 #12 x 5/8" Self-threading Phillips Head Screw #10 x 1-1/2" Screw Self Tapping 12” Enclose Enclose Enclose Solid Wall Solid Wall Solid Wall Rev: 4 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 34 #8-18 x 5/8" Self-Drilling Screw #10 x 1-1/2" Screw Self Tapping Square Drive Space screws about 2ft apart after rst screw 2’ 3” Rev: 4 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 35 #10 x 1" Self Drilling Screw #10 x 1-1/2" Screw Self Tapping Square Drive Use predrilled holes Rev: 4 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 36 Cut EFG vertical (K) to X height Attach vertical (K) to bracket (B) and pre-drill holes for bracket (B) NOTE: SET HEIGHT ADJACENT TO DOOR LOCATION. 3.5" ± 3/8" 3/16 drill bit Frameless Stack Rev: 4 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 37 Attach the EFG top rail to the EFG vertical rail (S101) (S100) #10 x 1-1/2" Screw Self Tapping #12-24 x 1/2" Screw S101 Install second bracket and EFG vertical as directed in steps 6-12. Frameless Stack Frameless Stack Enclose Enclose Enclose Solid Wall Solid Wall...
  • Page 38 NOTE: Engage rotate to clip top. IMPORTANT! CUT SQUARE TO AVOID GAPS! FOR INLINE FOR 90° ANGLES GAPS NO GAPS 1/2” Install trim (V1) Rev: 4 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 39 NOTE: Connections of this modular power distribution component MUST be done by a licensed electrician, who must control the size and loading of each branch circuit. The person or group installing Haworth products is responsible for complying with all applicable building and electrical code requirements.
  • Page 40 INSTALLING PDA Remove PDA bracket (A1) Remove brackets (A2) Install PDA (A) to PDA bracket (A1) Install brackets (A2) Install PDA (A) NOTE: Locate PDA bracket (A1) up against frame (P). NOTE: Label always faces opening. Rev: 4 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 41 TOP FEED Power Base AI infeed Power Base infeed Rev: 4 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 42 PANEL TO PANEL Rev: 4 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 43 PANEL TO PANEL DOUBLE PDA CONNECTION HARDWIRE INFEED Rev: 4 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 44 BASE FEED-INTERNAL 1.22" 6" 10" Power Base AI infeed BASE FEED-EXTERNAL Install base feed Route cord (F) through raceway (M) Power Base infeed TO JUNCTION BOX IN BUILDING Rev: 4 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 45 WIRING DIAGRAM 3 CIRCUIT WIRE COLOR Haworth Power Base components, are o ered in three di erent wiring schemat- = WHITE (12GA) ics to allow you to match your speci c wiring strategy to any typical building = WHITE RED (12GA) wiring plan.
  • Page 46 ENC® Section 8 - Cuttable and other Panel Types Side Cuttable Cat# 114-3843 Frame Wall Starter Tile Spring Starter Insert Raceway Bracket Leveler Cover Raceway Rev: 4 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 47 Measure distance for (X) Mark location on tile (A) X-1” Remove tiles (A) Remove raceway covers (H) and raceway bracket (F) Rev: 4 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 48 1" X" - 1" 2" X" Rev: 4 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 49 Reassemble components to frame (B) Install starter insert (E) Install wall starter (C) Rev: 4 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 50 Remove adjacent Panel Install Cut-down Pannel and replace adjacent Panel Panels Removed for Visual Clarity Level both Panels Rev: 4 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 51 Install reveal connectors (M) to secure panel Rev: 4 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 52 Top Cuttable Cat# 122-4742 Rev: 4 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 53 Rev: 4 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 54 Rev: 4 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 55 Rev: 4 8.10 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 56 Interface Panel Cat# 114-3834 USED FOR COLUMNS Double Stick Tape (1001424) Interface Panel Reveal Connector USED FOR WALLS Leveler Cover Rev: 4 8.11 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 57 Adjust levelers (E) to lower panel (A) Install panel (A) Install double stick tape (D) Rev: 4 8.12 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 58 Rev: 4 8.13 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 59 Frameless Corner 90° Cat# 114-3837 135° Cat# 114-3835 Trim Retainer 90° Upper Trim Panel Corner Blocks (Side A) 135° Panel (Side B) Bottom Trim Trim Retainer Leveler Covers Rev: 4 8.14 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 60 Remove shipping braces (H &J) Adjust levelers (K) to lower panel Rev: 4 8.15 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 61 Transom Only Remove nut (M) Install corner blocks (A) Rev: 4 8.16 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 62 Insert inside leveler covers (F) Install second panel (G) (Repeat steps 1-3) Level panel (G) Install outside leveler covers (F) Rev: 4 8.17 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 63 Install bottom trim (E) Install top trim (B) Rev: 4 8.18 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 64 3-Way Frameless Corner Cat# 114-3836 Trim Panel Center Panel Leveler Cover Adjust Levelers (E) to lower panel (A) Rev: 4 8.19 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 65 Stand up center panel (C) Rev: 4 8.20 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 66 Rev: 4 8.21 CUSTOMER SERVICE PHONE: 1-800-426-8562...

  • Page 67: Top View

    ENC® Section 9 - Special Walls Applications Spanning Tile Cat# 121-0800 #8-18 x 5/8" Self-Drilling Screw Square Drive Retaining Hook Bracket #8-12 x 1/2" Self-Drilling Screw Hanging Retaining Extrusion Bracket Bracket #8 x 1/2" Flat Head Screw If location has a spanning tile. DOES NOT have a spanning tile.
  • Page 68 Add brackets, repeat for all walls #8-18 x 5/8" Self-Drilling Screw Square Drive Rev: 4 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 69 POWER BASE PDA Place all Enclose panels in their intended nal location. Rev: 4 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 70 Insert a reveal connector (J) to the lip insert pieces to join the panels behind the entire height of the spanning tile(s) (E). Rev: 4 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 71 Rev: 4 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 72 To restrict bow and rattle in spanning or non-spanning tiles DO NOT USE FOR GLASS TILES #8-18 x 5/8" Self-Drilling Screw Square Drive Note: Notch should be aligned with the top of the tile below it, with a tolerance of +/- 1/8” (3mm). Rev: 4 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 73 2 5 m 1 ” ( + – #8-12 x 1/2" Self-Drilling Screw 5 1 m 2 ” ( i l e n i n T o p i l e n i n t t o ” ( 1 1 / 2 + –...
  • Page 74 Note: View from opposite side of frames shown for installation clarity. Continue the installation process to the top tile of the wall. After all tiles are installed, place all reveal connectors around the spanning tile and adjacent tiles. Rev: 4 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 75 Plywood Backer Cat# 114-6756 ( F) FOR CENTER VERTICALS Plywood Backer #10-16 x1.5” Self-Drilling Screw Supplied by Others Square check site conditions and use plywood based on speci c ( E) panels tile con guration #10-16 x 5/8" Self-Drilling Screw Square Drive FOR OUTSIDE VERTICALS Remove tile (B) from panel receiving plywood backer (A)
  • Page 76 NOTE: Panel Height and Height from Floor demsion is located For Panel Widths 24” and Less For Panel Widths Greater than 24” in Panel Type Report Rev: 4 9.10 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 77 CENTER VERTICALS ( E) Install brackets (D&C) as shown #10-16 x 5/8" Self-Drilling Screw Square Drive OUTSIDE VERTICALS Install backer (A) ( F) #10-16 x1.5” Self-Drilling Screw Square Plywood Install tile (B) Rev: 4 9.11 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 78 Paintable Tiles Rev: 4 9.12 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 79 Rev: 4 9.13 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 80 ENC® Section 10 - Wood/Metal Butt Hinge Doors Wd/Mtl Butt Hinge Doors W/ Lockset CAT# 122-7746 W/O Lockset CAT# 122-7747 Door Door Frame Hinge Plinth (Visual) Plinth (Hidden) Rev: 4 10.1 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 81 Adjust Levelers (G) to lower door frame (B) Install and level door frame (B) and set height with levelers (G) Rev: 4 10.2 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 82 Plinth Adjustment With door on its side, back out set screw (K) and adjust height with hex key on bolt (J) Tighten set screw (K) back into place with some non permanent thread locker Face plate Plinth exploded view Height adjustment bolt Set screw Modify and Install frame (B) to panels (H)
  • Page 83 Install hinges (D) to frame (B) Install door (A) Rev: 4 10.4 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 84 ENC® Section 11 - Glass Slab Butt Hinge Doors - Colcom Hinge Glass Slab Butt Hinge Doors W/ Lockset CAT# 122-7748 W/O Lockset CAT# 122-7749 M3 x 4mm” Set Screw Hinge Mount Glass Slab Door Plate #12-24 x 1/2” Screw Hinge Mount Plate Emery Paper...
  • Page 85 Shim glass door (A) in place (even gap all around frame (K) Attach hinge (C) to glass door (A) NOTE: Eccentric Bushings(D) can be loose within the holes in the glass slab door (A) without impeding performance. NOTE: Finger tighten until they stop then, using a 4mm Allen wrench tighten the scew 1/4 of a turn.
  • Page 86 Ensure Door (A) is operational within frame Attach hinge mount plates (H) M3 x 4mm” Set Screw After Installation Checklist Open & close door. Door gap should be even all around door. Check that the door does not drift open. If door drifts open then the door frame is not plumb.
  • Page 87 ENC® Section 12 - Glas Slab Pivot Door Glass Pivot Door W/ Lockset CAT# 122-7750 W/O Lockset CAT# 122-7751 Rev: 4 12.1 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 88 .75 (19mm) TO 1.25" (32mm) Rev: 4 12.2 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 89 NOTE: Part (C1) is temporarily install to get the proper height. Rev: 4 12.3 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 90 NOTE: Lithium Grease supplied by installer. Rev: 4 12.4 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 91 FINGER TIGHT 1/4 TRUN Rev: 4 12.5 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 92 Rev: 4 12.6 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 93 Rev: 4 12.7 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 94 EFG® Section 13 - Door - Double Glazed Aluminum - Pivot Double Glaze WD/AL W/ Lockset CAT# 123-9613 W/o Lockset CAT# 123-9614 (S109) #10-24 x 1/2" Flat Head Screw (S100) (S101) #10 x 1-1/2" Screw Self Tapping #12-24 x 1/2" Screw Rev: 4 13.1 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 95 .75 (19mm) TO 1.25" (32mm) Rev: 4 13.2 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 96 Rev: 4 13.3 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 97 (S109) S109 #10-24 x 1/2" Flat Head Screw NOTE: Door leaf frame should not extend above pivot extrusion, must be ABOVE BELOW FLUSH NOTE: Close door (BN), then open to adjust as needed. NOTE: Lithium Grease supplied by installer. 5/8” MAXIMUM Rev: 4 13.4...
  • Page 98 ENC® Section 14 - Enclose Sliding Doors Wood/Aluminum Sliding Door W/ Lockset CAT# 122-7753 W/O Lockset CAT# 122-7754 Door Track Rail Cover (Plastic or Aluminum) Door CAUTION Door Stop NOT FOLLOWING THESE DIRECTIONS COULD RESULT IN PROPERTY DAMAGE OR INJURY NOTE: For double door Door Frame frames (G) are shipped...
  • Page 99 Rev: 14.2 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 100 For Solid Panels Only: Prep Panel Receiving Door Track Remove parts (J) from panel (K) Install door brace (B) Reinstall parts (J) to panel (K) Rev: 14.3 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 101 Level panel (K) Install panel (K) next to door frame (G) (as shown) Rev: 14.4 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 102 For Aluminum For Plastic Rev: 14.5 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 103 With door on its side, back out set screw (K) and adjust height with hex key on bolt (J) Tighten set screw (K) back into place with some non permanent thread locker Rev: 14.6 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 104 Rev: 14.7 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 105 Rev: 14.8 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 106 Rev: 14.9 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 107 Adjust and then tighten door stop (H) NOTE: Tighten 3/4 turn after feeling additional resistance. Tip of screws must leave indents in c-channel (C) . IMPORTANT: ADJUST DOOR STOPS (H) SO THEY STOP THE DOOR THE SAME TIME AS THE BOTTOM GUIDE. Locate bracket (T) and install one screw (U) Adjust bracket (T) and install second screw (U) 1.5mm...
  • Page 108 ENC® Section 15 - Enclose Sliding Glass Slab Doors Glass Sliding Doors W/Lockset CAT# 122-7755 Solid sidelight walls only Door Brace Door Track Rail Cover Hanger Brackets Track Insert Door Door Stop CAUTION NOT FOLLOWING THESE DIRECTIONS COULD RESULT IN PROPERTY DAMAGE OR INJURY Door Frame...
  • Page 109 Adjust levelers (P) to lower door frame (M) NOTE: Install the door guide bracket that is correct for the door hand. .75 (19mm) Install door frame (M) Level door frame (P) .75 (19mm) TO 1.25" (32mm) Rev: 4 15.2 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 110 For Solid Panels Only: Prep panel Receiving Door Track Remove parts (J) from panel (K) Install door brace (B) Reinstall parts (J) to panel (K) Rev: 4 15.3 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 111 Install panel (R) next to door frame (M) (as shown) Level panel (R) .75 (19mm) TO 1.25" (32mm) Rev: 4 15.4 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 112 Install door track (C) (as shown) NOTE: Make sure track NOTE: Use the supplied screws cut-outs are always in all available locations installed up as shown. 1/8" (3.2mm) #10-16 x 1-1/2" Flat Head Tek Screw Install center rail cover (D) only Rev: 4 15.5 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 113 Install hanging brackets (E) NOTE: Install black spacers. If it does not t, use the white spacer to ensure a tight t. NOTE: Tighten to 5 foot-pounds by hand only. If necessary center hanging brackets (E) Check List Is there foam on the hanger brackets that contact the glass? Is the sidelight brace attached on the top header Are there nylon bushings for the glass holes? Use...
  • Page 114 Rev: 4 15.7 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 115 Rev: 4 15.8 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 116 Install door trim (H) Install metal bar (G) center and secure door trim (H) NOTE: Tighten set screws until ush. Adjust door trim (H) height X - 5.5mm = Y (7/32") Rev: 4 15.9 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 117 Install covers (B1) NOTE: Tighten 3/4 turn after Adjust and then tighten feeling additional resistance. Tip door stop (N) of screws must leave indents in c-channel (C) . IMPORTANT: ADJUST DOOR STOPS (N) SO THEY STOP THE DOOR THE SAME TIME AS THE BOTTOM GUIDE.
  • Page 118 Rev: 4 15.11 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 119 Note: Doors must be leveled when closed Rev: 4 15.12 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 120 ENC® Section 16 - WD/MTL Softclose Sliding Door WD/MTL Soft close Sliding door Mounting Rail Track End Cap W/Lockset CAT# 123-9615 W/O Lockset CAT# 123-9616 W/Lockset & W/Pull CAT# 123-9617 Door Support Track Fascia Cover Fascia Retainer Door Stop Arm Door Stop Roller Assembly Track End Cap...
  • Page 121 Rev: 4 16.2 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 122 For Solid Panels Only: Prep Panel Receiving Door Track Remove parts (J) from panel (K) Install door brace (B) (B2) #8-24 x 1/2" Self-Drilling Screw Reinstall parts (J) to panel (K) Rev: 4 16.3 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 123 Reinstall the wall panel Rev: 4 16.4 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 124 FOR INSTALLING SLOW CLOSE (A2) #8 x 1-1/2" Flat Head Self-Drilling Screw 2.5mm (3/32”) Mounting Rail (D2) 1/4-20 x 1/2" Set Screw Door Support Track Fascia Retainer Rev: 4 16.5 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 125 NOTE: Do not remove screws. Only loosen screws. Door Stop Door Stop Arm Door Stop (3/8”) (3/8”) Roller Assembly Door Stop Arm Track End Cap (B2) #8-24 x 1/2" Self-Drilling Screw Rev: 4 16.6 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 126 Rev: 4 16.7 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 127 Door Bracket Rev: 4 16.8 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 128 6mm (1/4”) Rev: 4 16.9 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 129 CLOSE DOOR NOTE: Mark location of door stop (G). Door Stop Arm OPEN DOOR Door Stop NOTE: Adjust stop and secure. Door Stop Arm (F2) NOTE: Secure arm #8 x 5/8" Self-Drilling Flat Head Screw through door track. Rev: 4 16.10 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 130 Repeat steps 12 & 13 to locate the door stop (G) for open postion NOTE: Mark location OPEN DOOR of door stop (G). Fascia Cover Rev: 4 16.11 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 131 With door on its side, back out set screw (K) and adjust height with hex key on bolt (J) Tighten set screw (K) back into place with some non permanent thread locker Locate bracket (T) and install one screw (U) Adjust bracket (T) and install second screw (U) 1.5mm (1/16")
  • Page 132 ENC® Section 17 - Glass Slab Soft Close Sliding Door Glass Slab Soft Close Sliding Door W/Lockset CAT# 122-7755 W/O Lockset CAT# 122-7756 (A2) (D2) Mounting Rail Track End Cap 1/4-20 x 1/2" Set Screw #8 x 1-1/2" Flat Head Self-Drilling Screw (B2) #8-24 x 1/2"...
  • Page 133 FOR INSTALLING SLOW CLOSE (A2) #8 x 1-1/2" Flat Head Self-Drilling Screw 2.5mm (3/32”) Mounting Rail (D2) 1/4-20 x 1/2" Set Screw Door Support Track Fascia Retainer Rev: 4 17.2 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 134 NOTE: Do not remove screws. Only loosen screws. Door Stop Door Stop Arm Door Stop (3/8”) (3/8”) Roller Assembly Door Stop Arm Track End Cap (B2) #8-24 x 1/2" Self-Drilling Screw Rev: 4 17.3 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 135 (L2) #8 x 5/8" Flat Head Screw Door Bracket Door Bracket Mounting Rail Mounting Rail Rev: 4 17.4 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 136 Door Bracket Roller Assembly Rev: 4 17.5 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 137 (B2) #8-24 x 1/2" Self-Drilling Screw End Cap End Cap 6mm (1/4”) Rev: 4 17.6 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 138 CLOSE DOOR NOTE: Mark location of door stop (G). Door Stop Arm OPEN DOOR Door Stop NOTE: Adjust stop and secure. Door Stop Arm (F2) NOTE: Secure arm #8 x 5/8" Self-Drilling Flat Head Screw through door track. Rev: 4 17.7 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 139 Repeat steps 12 & 13 to locate the door stop (G) for open postion NOTE: Mark location OPEN DOOR of door stop (G). Fascia Cover Rev: 4 17.8 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 140 EFG® Section 18 - Double Glazed Softclose Sliding Door DBL GLZ SoftClose Sliding Door (S106) W/Lockset CAT# 123-9615 W/Pull CAT# 123-9616 W/Pull & W/Lockset CAT # 123-9617 #8 x 1-1/2" Flat Head Self-Drilling Screw S109 S109 S107 NON-LOCKING S106 S101 S-99 S113 (S113)
  • Page 141 .75 (19mm) TO 1.25" (32mm) Rev: 4 18.2 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 142 For Solid Panels Only: Prep Panel Receiving Door Track Remove parts (J) from panel (K) Install door brace (B) Reinstall parts (J) to panel (K) Rev: 4 18.3 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 143 For 1 Channel ONLY (S106) #8 x 1-1/2" Flat Head Self-Drilling Screw LOCKING NON-LOCKING 1/8" (3.2mm) S106 S106 (S113) 1/4-20 x 1/2" Set Screw S113 S113 Rev: 4 18.4 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 144 NOTE: Do not remove screws. Only loosen screws. Door Stop Door Stop Arm Door Stop (3/8”) (3/8”) Door Stop Arm Roller Assembly S-99 Track End Cap (S-99) S-99 #8-24 x 1/2" Self-Drilling Screw Rev: 4 18.5 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 145 S109 LOCKING DOOR NON-LOCKING DOOR DOUBLE DOOR (S109) #10-24 x 1/2" Flat Head Screw 1/2” 3/4” 5/8” S109 NOTE: Handle door with care. Do not drag door, it will damage the seal. NOTE: Material is supplied by the installer. Rev: 4 18.6 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 146 Door Bracket Roller Assembly 1/4” Shim NOTE: Remove shim after door is installed. NOTE: Shim is supplied by the installer. Rev: 4 18.7 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 147 10mm 5/8” MAXIMUM 5/8” MAXIMUM Rev: 4 18.8 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 148 CLOSE DOOR NOTE: Mark location of door stop (AL) . Door Stop Arm OPEN DOOR S111 Door Stop NOTE: Adjust stop and secure. S111 S111 Door Stop Arm (S111) NOTE: Secure arm through door track. #8 x 5/8" Self-Drilling Flat Head Screw Rev: 4 18.9 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 149 Repeat steps 14 & 15 to locate the door stop (AL) for open posItion NOTE: Mark location OPEN DOOR of door stop (AL) . 8” AH Fascia Cover Rev: 4 18.10 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 150 For Double Doors only Rev: 4 18.11 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 151 For Double Doors only Note: Doors must be closed when leveling. Rev: 4 18.12 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 152 For Double Doors only UNEVEN NOT CENTER FLUSH & CENTER DOUBLE DOORS GAPS FLUSH NO GAPS NOTE: Screws are provided by installers and per local jurisdiction. IMPORTANT! BRACKET REQUIRED FOR DROP SEAL ACTIVATION. DROP SEAL FILLS IN THE GAP TO REDUCE NOISE. Rev: 4 18.13 CUSTOMER SERVICE PHONE: 1-800-426-8562...

  • Page 153: Section 19 - Door Hardware

    EFG® Section 19 - Door Hardware Metal Glazed Door (Mortise latchset may not be as shown) Rev: 4 19.1 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 154 Options - Cylinder Patch Kit 126-1342 ENCSP Patch, DblGlz Pvt/Dr, Actv 126-1343 ENCSP Patch, DblGlz Pvt/Dr, Inactv 126-1344 ENCSP Patch, DblGlz Sl/Dr w/Lkset 126-1345 ENCSP Patch, DblGlz Sl/Dr w/Pull & Lk Metal Glazed Door (Cylinder latchset may not be as shown) Rev: 4 19.2 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 155 Options - Mortise Patch Kit (Right-Hand application shown) Lock Body Lock Body Cover Screw (FSB SM-I latchset shown for Armor Plate Screw instruction purposes only) Armor Plate Lock Body Plate Dovetail Cover Lock Body Gasket Spacer #12-24 x 1/2" Flat Head Screw Dovetail Gasket Dovetail...
  • Page 156 Options - Mortise Patch Kit Rev: 4 19.4 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 157 Options - D-Pull Spacers for Double Glazed/Wood Doors Only NOTE: D-Pulls type may not be as shown. Assemble D-Pulls per manufacturer’s instructions. (S385) NOTE: For this screw (S385) Complete STEPS 2 & 4 only. 5/16-18 x 3" Push/Pull Bolt Single Slab Doors Double Glaze/Wood Doors (S382) REINSTALL...
  • Page 158 DBL-GLZ Electric Strike Electric Strike Rutherford L6505 (Left-Hand Reverse application shown) WD/MTL Electric Strike D-Pulls type may not be as shown. Assemble D-Pulls per manufacturer’s instructions. Rev: 4 19.6 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 159 Options - Roller Catch (Right-Hand application shown) Roller Catch Bracket (align with Roller Catch mechanism in door frame) Double-sided Tape Glass Door Top Corner Strike Side Rev: 4 19.7 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 160 Options - Hook Lock Hook Lock hardware kit Adams Rite 2331 Heavy Duty Deadbolt Blocking Ring 3/8” (Locking Cam may not be exactly as shown) (used for Left-Hand applications) Standard Core Blocking Ring 1/4” (used for Right-Hand applications) Blocking Ring 3/8” (used for Left-Hand applications) Small Format IC Housing Blocking Ring 1/4”...
  • Page 161 Options - Hook Lock (Right-hand application shown) (Right-hand application shown) Rev: 4 19.9 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 162 Options - Hook Lock for Double Glazed Doors Hook Lock hardware kit Adams Rite 2331 Heavy Duty Deadbolt Blocking Ring 3/8” (used for Left-Hand applications) (Locking Cam may not be exactly as shown) Standard Core Blocking Ring 1/4” (used for Right-Hand applications) Blocking Ring 3/8”...
  • Page 163 Options - Hook Lock Metal Glazed Door (Right-hand application shown) (Right-hand application shown) Rev: 4 19.11 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 164 Hook Bolt Lock Cover 119-1802 L-pull locking Non-Locking Pull Dovetail Plate Gasket Dovetail Plate Locking Pull Cylinder Thumbturn Rev: 4 19.12 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 165 Install dove tails (C) as shown Install non-locking pull (A) Install locking pull (E) Install cylinder thumbturn (F) NOTE: Refer to manufactures product instructions when installing the lock and door knobs. Rev: 4 19.13 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 166 Top Lock Sliding Door for ENC Standard Sliding Doors Adjust hex bolt (A) Install hex bolt (A) NOTE: Apply Threadlocker as shown Rev: 4 19.14 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 167 Rev: 4 19.15 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 168 Top & Bottom Flush Bolt for Glass Slab Doors Inactive Leaf. Rev: 4 19.16 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 169 Insert nylon spacer (A) into Glass (H) Apply rubber grommet (B) and then trim overhang Align main house (D) & (C) and attach with screw (E) Slide Tab (G) into houseing (D) Attach Pin (F) to Tab (G) Insert Ball bearing (J), (K) and set screw (L) into Housing (D) and tighten set screw(L) Rev: 4 19.17...
  • Page 170 Options - Closer (only) Closer Body Closer - Dorma ITS-9625 Closer Mechanism (Right-Hand reverse application shown on a Metal Glazed Door) Double-sided Closer Arm #10-32 x 1/4" Flat Head U/C Screw Closer Track Closer Cover Screw Plate Closer Track Closer Cover #10-32 x 3/8"...
  • Page 171 Options - Closer (only) Attach closer to door header Note: Brackets are factory Installed Closer Arm Re-assemble Closer Arm with Door assembly. Adjust Closer per manufacturer’s instructions. Rev: 4 19.19 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 172 120-0629 Enhanced Door Seals FOR REMOVING DOOR Frame Seal Frame Seal Door Seal Aluminum Door Trim End Cap Trailing (Plinth) Tape Sheet Door Stop End Cap (Soft Close) Rev: 4 19.20 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 173 Rev: 4 19.21 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 174 130 MM Saved if door has plinth NOTE: Door must be cleaned with isopropyl alcohol before installing aluminum trim (B). Install from top to bottom to avoid bubbles. Follow cleaning guides. End Cap (Plinth) Rev: 4 19.22 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 175 22mm 10mm 10mm 22mm 30mm Rev: 4 19.23 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 176 FOR DOOR LATCHS ONLY Maximum Rev: 4 19.24 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 177 FOR SOFT CLOSE DOOR (D2) End Cap (Soft Close) #8-24 x 1/2" Self-Drilling Screw Rev: 4 19.25 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 178 FOR DOUBLE DOORS NOTE: Door must be cleaned with isopropyl alcohol before installing aluminum trim (A2) . ENCLOSE® Reinforcement Bracket for Doors NOTE: Tape Plastic A2 Installation Instructions to Plinth Cap Rev: 4 19.26 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 179 REINFORCEMENT BRACKET FOR DOORS- 1015058 Wood/Aluminum doors Remove 2 screws (A) (shown) 11/64" Reinstall 2 screws (B) (shown) with brackets (C) (4.5mm) NOTE: For optimal results install bracket (C) in hinge locations shown. #12-24 x 1/2" Screw #12-24 x 1" Screw Glass Door 11/64"...
  • Page 180 Secure brackets (C) (as shown) #12 x 1/2" Metal Self-tapping Pan Head Screw FOR 3-WAY CONDITIONS Repeat steps 1 and 2 #12 x 1/2" Metal Self-tapping Pan Head Screw Rev: 4 19.28 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 181 FOR WOOD/ALUMINUM DOORS INLINE POST CONDTION Remove 2 screws (A) (shown) (B1) Reinstall 2 screws (B) (shown) with brackets (C) #12 x 1/2" Metal Self-tapping Pan Head Screw NOTE: For optimal results install bracket (C) in hinge locations shown. 11/64" (4.5mm) #12-24 x 1/2"...
  • Page 182 Secure brackets (C) (as shown) FOR 3-WAY CONDITIONS Secure brackets (C1) (as shown) Rev: 4 19.30 CUSTOMER SERVICE PHONE: 1-800-426-8562...
  • Page 183 ENC® Section 20 - Pro les Plastic COVER PLUG SKIN CLIP 8MM HALF LIPZIP 6MM GLAZING BEAD EXTRUSION DRYWALL GLASS FILLER FIN HORIZONTAL DEMOUNTABLE SKIN CLIP BULB SEAL Base RAIL SEAL FIN SEAL STEEL - SHORT FABRIC SKIN CLIP 3 WAY CONNECTOR CLIP BASE 10MM GLAZING BEAD VERTICAL SEAL...
  • Page 184 ENC® Section 20 - Pro les Plastic INNER CORNER SLIDING DOOR RAIL TRACK ACCOUSTICAL POST CLIP SKIN SEAL FRAME TRIM COVER SEAL 135 DEGREES REMOVABLE TRAILING EDGE STARTER SLIDING DOOR REVEAL FLAP STARTER CUTTALBE ADJUSTABLE FRAME TRIM CUTTABLE FEMALE COMPONENT LIPZIP LEADING EDGE POST CLOSE...
  • Page 185 ENC® Section 20 - Pro les Aluminum RECT AL BOT EXT VERT EXT TOP HORZ EXT MUNTIN HORZ EXT INTERFACE PANEL AL RECT GLASS WALL AL RECT GLASS WALL AL RECT GLASS WALL VERTICAL BOT HORZ EXT SLIDING DOOR PASSTHROUGH EOR LOW PROFILE AL RECT GLASS WALL HORIZONTAL...
  • Page 186 ENC® Section 20 - Pro les Aluminum POST MOD BASE HORZ EXT POST 135 CLAD AL BASE CLAS EXT CONNECTOR GLASS FILLER FIN GLASS FILLER FIN AL TRIM ATTACH EXT VERT SKIN FRAME EDGE AL GLASS CLAD 2WAY FRAMLESS CORNER PROTECT REMOVEABLE STARTER CLAD POST ON-MOD...
  • Page 187 ENC® Section 20 - Pro les Aluminum INTERFACE PANEL VERT SLIDING TOP STOP BODY EXT BOT UNITIZED HORZ TRANSOM HORZ SAE DOOR FRAME SLIDING DOOR AL RECT GLASS AL RECT GLASS LOCKING JAMB BUTT HIDGE STILE BOT HORZ EXT FREESTANDING CAP AL DOOR 3WAY VERT EXT AL RECT GLASS WALL...
  • Page 188 ENC® Section 20 - Pro les Aluminum INNER VERT FRAME SOLID REMOVABLE FASCIA EXT EXT MOUNTING RAIL CUTTABLE HORZ EXT SOLF CLOSE GLASS SLAB SLIDING SOL FRAME SLIDING DOOR DOOR SOFT CLOSE TRACK EXT UPPER BOTTOM C-CHANNEL RAIL SOFT CLOSE HORZ REMOVABLE TRK COVER SLIDING DBL DOOR INACTIVE...