Advertisement
Quick Links
ARMOR FENDERS
2020+ JEEP GLADIATOR JT
FDGL-09
TOOLS
REQUIRED
- Safety Glasses
- #4 Allen Tool
- 8mm, 10mm Socket/Wrenches
- Rubber Mallet
- Preferred Cutting Tool
- Paint
- Nutsert Tool
WARNINGS/CAUTIONS BEFORE STARTING INSTALLATION
Before you install this kit —
instructions, warnings, cautions, and notes contained in
this installation instruction guide. Consult your vehicle
owner's manual for proper disconnection of electrical and
lifting of vehicle if required for installation of this product.
This install may require some technical skills and
knowledge of basic mechanical work. If you do not feel that
you are capable of performing this install please take this
product to a trained professional.
After reading this guide please contact us with any
questions or concerns before installing product.
Customer Service: 855-680-9595
DV8 Offroad is not responsible for any bodily injury or harm to you
or your vehicle as a result of an improper install.
555 E Queen Creek Rd
Bldg A
Chandler, AZ 85286
WWW.DV8OFFROAD.COM
SKILL
LEVEL
- Novice/Intermediate
- 1 (you) to 2 persons
Little skill level required, you can
easily install it by yourself however,
additional help will be useful
Read and understand all
INSTALLATION
PRODUCT
TIME
- 3.5 Hours
Time to install this should only
take about an three and a half
hours.
Proper installation of this kit required knowledge of the factory
recommended procedures for removal and installation of original
equipment components. We recommend that the factory shop manual
and any special tools needed to service your vehicle be on hand during
the installation. Installation of this kit without proper knowledge of the
factory recommended procedures may affect the performance of these
components and the safety of the vehicle
• Always wear eye protection when operating power tools
Inspect all contents of this package to make sure product is not damaged
and all installation hardware has been included. If parts are missing from
kit, please be prepared to provide the following information
1. Name of purchase location
2. Bar Code on side of box
3. Date above bar code
4. Date inside box cover
NEED HELP?
MANUAL
REQUIRED
855-680-9595
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for DV8 OFFROAD FDGL-09
Summary of Contents for DV8 OFFROAD FDGL-09
- Page 1 1. Name of purchase location Customer Service: 855-680-9595 2. Bar Code on side of box DV8 Offroad is not responsible for any bodily injury or harm to you 3. Date above bar code or your vehicle as a result of an improper install.
- Page 2 INSTALLATION MANUAL Begin by unpacking all items and inspecting for missing pieces or damage. If you have any concerns, please contact the company the product was purchased from. Extra hardware may be included with the product. HARDWARE INCLUDED (18) M6x20mm Allen Head (9) M6 Washers Bolts (22) M6x20 Allen Head...
- Page 3 INSTALLATION MANUAL STEP 2 | Unplug the turn signal indicator by pulling the red release tab out and pushing on the black locking tab. STEP 3 | Use a 10mm socket to remove the bolt securing the fender to the vehicle.
- Page 4 INSTALLATION MANUAL STEP 4 | Use a trim clip tool to remove the factory clips along the fender. Repeat process for the other side. STEP 5 | (Rear uninstall) Use a 8mm socket to remove the bolts located along the interior of the inner fender. Use a trim clip tool to remove the clips located in each corner of the fender.
- Page 5 INSTALLATION MANUAL STEP 6 | Remove the fender flare by pulling the front section towards the front of the vehicle, and the rear section towards the rear. Pull the fender directly away from the vehicle, to release the remaining clips. You should be able to reach around and squeeze the clips to remove if needed.
- Page 6 INSTALLATION MANUAL STEP 7 | Use a trim clip tool to remove the clips along the edge of the fender that remained in the vehicle. Repeat process for the other side. STEP 8 | Using your preferred cutting tool, cut the circled fender mounts off and grind them down so it is flush with the vehicle.
- Page 7 INSTALLATION MANUAL STEP 9 | Hold up the fender to the vehicle and note which holes will be used. Install the provided nutserts using a nutsert tool. If you do not own a nutsert tool, we provide one with our kit. For instructions on how to use the nutsert tool, scroll to the last page.
- Page 8 INSTALLATION MANUAL STEP 12 | If planning to bypass vent cover, cut the seal at the fender corner. Continue the seal down the fender aligning the seal cut outs with the mounting holes in the fender. Cut off any excess seal. Ensure the seal wraps around the front of the fender corner.
- Page 9 INSTALLATION MANUAL STEP 13 | Remove the factory fender vent cover using a trim clip tool to pry the bottom away from the fender, then slide the cover toward the front of the vehicle to free the cover from the fender. 855-680-9595 NEED HELP?
- Page 10 INSTALLATION MANUAL STEP 14 | Lift the DV8 Armor fenders up to the vehicle and loosely secure the fender using the provided M6x20mm allen head bolt and a #4 allen tool. Use (1) Split washer and (1) flat washer per M6 bolt.
- Page 11 INSTALLATION MANUAL STEP 16 | Feed the provided marker light through the back of the DV8 armored fender. Feed the rubber grommet through the fender light cutout. STEP 17 | Press the marker light into the rubber grommet, route the marker light wiring harness behind the inner fender and connect plug it in to the vehicles factory fender/turn single light...
- Page 12 INSTALLATION MANUAL STEP 18 | (Rear Installation) Use a rubber mallet to install the U-shaped rubber seal onto the DV8 rear armor fenders as shown. STEP 19 | Cut any excess seal off the end. 855-680-9595 NEED HELP?
- Page 13 Install the provided nutserts using a nutsert tool. STEP 21 | The FDGL-09 rear fenders are designed to work with the DV8 SRGL- 01 Bedside Rock Sliders. If you are running the factory plastic bedside covers they will need to be trimmed.
- Page 14 INSTALLATION MANUAL STEP 22 | Lift the rear fender up to the vehicle and loosely secure the fender to the vehicle using the provided M6x20mm allen head bolts. Use (1) split washer and (1) flat washer per M6 allen head bolt. STEP 23 | With all hardware started, secure the fender in place using a #4 allen...
- Page 15 INSTALLATION MANUAL STEP 25 | (Nutsert tool guide) To use the nutsert tool, slide the M6 washer and spacer onto the provided M6x50 bolt. Then install a nutsert onto the exposed threads by hand. STEP 26 | Slide the nutsert tool with the nutsert into the mounting hole.
Need help?
Do you have a question about the FDGL-09 and is the answer not in the manual?
Questions and answers