Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Kaiweets KOTC02
Summary of Contents for Kaiweets KOTC02
- Page 1 User's Manual Paint Thickness Meter KOTC02 Contact us: support@kaiweets.com...
- Page 2 Introduction Thank you for selecting the KAIWEETS KOTC02 paint thickness gauge.The gauge adopts the principle of electromagnetic induction and eddy current effect to distinguish the properties of the metal substrate precisely. With the precision integrated probe, it can accurately measure the thickness of non-magnetic coatings on magnetic substrate surface (e.g.
- Page 3 Key and User Interface Battery indication Substrate property Thickness value Unit Storage records Note: Fe is for magnetic material, NFe is for non-magnetic material. Unit switch/Select up Setting/ Storage/Rotation Calibration Zero Calibration/ Select down...
- Page 4 Home Screen On the home screen, no shows on the upper left corner. Short press to set the warning value of upper limit “ ”or lower limit “ ” ; Long press for calibrating mode; During measuring process, short press the key to switch between single and continuous measuring mode.
-
Page 5: Setting Alarm Limits
Setting Alarm Limits On the home screen, short press key to set the upper or lower limit of warning value, on the upper left corner shows “ ” or “ ” Short press to save and go to next. Short press to increase warning value by 1; Long press to increase in succession. -
Page 6: Battery Notes
Battery Notes The gauge can only be used with 1.5V AAA alkaline batteries. When the meter is not used for a long time, please remove the battery to avoid the battery corrosion from the meter. If the power icon is , it means the power is full, and the meter can work regularly and accurately. -
Page 7: Power On And Off
Power On and Off Power on: Keep away from metal materials ≧ 5 cm then touch the probe to turn it on. Power off: 60 seconds of no operation automatic shutdown. Attention: • When the instrument is turned on near the metal material, it will “beep...b eep...”... - Page 8 Basic operations： 1. Long press the key, on the upper left corner of the screen shows“ ”, the meter is in calibration mode, see the figure below: Calibration mode Corresponding thickness value Calibration points 1 (0μm) 2 (50μm) 3 (100μm) 4 (250μm) 5 (500μm) 6 (1000μm) Attention: All other points can be adjusted according to the value of the calibration sheet thickness except for the zero point.
- Page 9 4. Refer to the previous step C, continue to calibrate the 3(100µm), 4(250µm), 5(500µm), 6(1000µm). After the sixth spot is calibrated, the meter exits the calibration mode automatically. 5. If just want to calibrate one of the six spots, then press the key to switch the calibration spots in calibration mode.
-
Page 10: Basic Measurement
Basic Measurement Single measurement Prepare the sample to be tested. Place the meter in vacant space away from metal material for turning Start to measure: Press slightly the meter vertically on the sample, the buzzer sounds “ beep ” once, on the main display area shows the result data, move the meter away from the sample over 5cm quickly, and process next measurement after 1 second. -
Page 11: View Records
Memory/Delete Records Memory records Short press to save the datum after affirming the validity of it. The meter will indicate “ ” icon which means the capacity of memory is full when the stored datum are over 30 sets. View records A. -
Page 12: Unit Setting
Limit Value Measurement The operation is for setting the upper and lower limit of the warning value. When the measured value is beyond the upper limit, on the upper left corner of the screen shows “ ”; when the measured value is below the lower limit, on the upper left corner of the screen shows “... -
Page 13: Specifications
Specifications Model KOTC02 Magnetic material 0~2999µm; Measuring range Non magnetic material 0~2999µm 0.1μm@ (0~99.9μm) Resolution 1μm@(100~2999μm) ±(2+2%)μm @ (0~500μm) Accuracy ±2.5%μm @ (500~2999μm) Magnetic material 25×25mm; Min measuring area Non magnetic material 25×25mm Min curvature Convexity 5mm; concave 30mm Magnetic material 0.2mm;... -
Page 14: General Maintenance
General Maintenance Keeping in high temp and humidity environment in the long run is not allowed; please put it inside the box and keep the box in dry and cool place. Please keep the surface clean, wipe the dust with wet soft cloth, do not use corrosive cleaning fluid.
Need help?
Do you have a question about the KOTC02 and is the answer not in the manual?
Questions and answers