TMG -SLG59 Product Manual

Mini skid steer rotating mini grapple

Advertisement

Quick Links

TMG-SLG59
PRODUCT MANUAL
v.2024.09.05
MINI SKID STEER
ROTATING MINI GRAPPLE

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the TMG-SLG59 and is the answer not in the manual?

Questions and answers

Summary of Contents for TMG TMG-SLG59

  • Page 1 TMG-SLG59 PRODUCT MANUAL v.2024.09.05 MINI SKID STEER ROTATING MINI GRAPPLE...
  • Page 2: Table Of Contents

    TREE PUSHER ..................................13 LOG DOGS ....................................13 RECEIVER HITCH ................................... 13 .................................... 14 ORQUE SPECIFICATION ..................................15 & C ..............................15 PECIFICATIONS APACITIES PARTS LIST ..................................15 TMG-SLG59R ........................16 OTATING RAPPLE SSEMBLY www.tmgindustrial.com 2 / 18 TOLL FREE: 1-877-761-2819...
  • Page 3: Important Safety Information

    Your Safety YOU are responsible for the SAFE operation and maintenance of your TMG Mini Skid Steer Rotating Mini Grapple. YOU must ensure that you and anyone else who is going to use, maintain or work around the Mini Skid Steer Rotating Mini Grapple be familiar with the using and maintenance procedures and related SAFETY information contained in this manual.
  • Page 4: Equipment Safety Guidelines

    - Heavy gloves - Wet weather gear - Hearing Protection 6. Install and secure all guards before starting. 7. Wear suitable ear protection for prolonged exposure to excessive noise. 8. Turn machine off, stop and disable engine, remove ignition key and place in your pocket, set park brake and wait for all moving parts to stop before servicing, adjusting, repairing, or unplugging.
  • Page 5: Safety Training

    8.Do not modify the equipment in any way. Unauthorized modification may result in serious injury or death and may impair the function and life of the equipment. 9.In addition to the design and configuration of this implement, including Safety Signs and Safety Equipment, hazard control and accident prevention are dependent upon the awareness, concern, prudence, and proper training of personnel involved in the operation, transport, maintenance, and storage of the machine.
  • Page 6: Safety Decals

    5.Safety signs are available from your authorized Distributor or Dealer Parts Department or the factory. Safety Decals Preparation 1.Never use the machine until you have read and completely understand this manual, the Mini Skid Steer Operator's Manual and each of the Safety Messages found on the safety signs on the Mini Skid Steer and machine. 2.Personal protection equipment including hard hat, safety glasses, safety shoes, and gloves are recommended during assembly, installation, operation, adjustment, maintaining, repairing, removal, cleaning, or moving the unit.
  • Page 7: Hydraulic Safety

    3.Make sure there is plenty of ventilation. Never operate the engine of the towing vehicle in a closed building. The exhaust fumes may cause asphyxiation. 4.Before working on this machine, shut off the engine, set the brake, and turn fuel valve off. 5.Never work under equipment unless itis blocked securely.
  • Page 8: To The New Operator Or Owner

    5.Be a safe and courteous driver. Always yield to oncoming traffic in all situations, including narrow bridges, intersections, etc. Watch for traffic when operating near or crossing roadways. To the New Operator or Owner Follow all safety instructions exactly. Safety is everyone's business. By following recommended procedures, a safe working environment is provided for the operator, bystanders, and the area around the worksite.
  • Page 9: Unhook Toro Mount Hitch

    Check for structural cracks in the hitch plates. Repair or replace hitch plates as needed. Check hitch components frequently. Repair or replace any part that is excessively worn, bent, broken, or missing. Lubricate lock pins (#1) at the prescribed interval in your compact loader manual. Check operation of lock pins (#1).
  • Page 10: Machine Operator Awareness

    Engage the lock pins to secure The Rotating Mini Grapple to the loader. Connect the hydraulics: Use a clean rag or paper towel to clean the dirt from the couplers on the hose ends of the Mini Skid Steer. Connect the hoses to the Mini Skid Steer couplers. Be sure the couplers are securely seated. Route and secure the hoses along the frame with clips, tape or plastic ties to prevent binding and pinching.
  • Page 11 Place the attachment on the ground in such a position that it cannot move during maintenance, transporting, cleaning, adjustments, and installation of accessories or storage. Do not put the attachment into such uses, for which it is not designed. The danger zone is 100 feet; ensure that no one is inside the danger zone, take special note of children, cease all operation if children are present in the danger zone.
  • Page 12 12 Volt Wire Diagram for Hydraulic Diverter To operate the diverter some loaders require this switch and circuit to be installed when only one auxiliary circuit is available. This circuit will operate a hydraulic diverter valve. In the de-energized state the auxiliary hydraulic circuit will control the opening and closing of the grapple.
  • Page 13: Equipment Feature Warnings

    EQUIPMENT FEATURE WARNINGS Unique Branch Manager Features ROPE BOLLARD Rated for 200 lbs. Never exceed your equipment operating capacity TREE PUSHER Never exceed your machine’s operating Capacity LOG DOGS Never exceed your machine’s operating Capacity RECEIVER HITCH Never exceed your machine’s operating Capacity Round stock inserts into the bottom of Grapple Hanger—Pin it In.
  • Page 14: Maintenance

    MAINTENANCE Before Every Use Check that all fasteners (nuts, bolts, pins, keepers) are in their right place and are tight. Inspect and replace any worn, torn or missing safety decals. Investigate the location of any oil leaks and repair. Lubricate all joints with lithium grease. Every Week Check the condition of the cutting edge and/or tooth points.
  • Page 15: Specification

    Torque figures indicated above are valid for non-greased or non-oiled threads and heads unless otherwise specified. Therefore, do not grease or oil bolts or cap screws unless otherwise specified in this manual. When using locking elements, increase torque values by 5%. * Torque value for bolts and cap screws are identified by their head markings SPECIFICATION Specifications &...
  • Page 16: Parts List

    PARTS LIST Rotating Mini Grapple Assembly www.tmgindustrial.com 16 / 18 TOLL FREE: 1-877-761-2819...
  • Page 17 Part No. Ref. Part Description RLG61.1TMG TORO Hanger Mount B-G057830-8*25 Bolt M8*25 B-G000930-8 Washer 8 B-G00097A-8 Washer 8 B-G00889A-8 Nut M8 B-G057830-8*20 Bolt M8*20 RLG61.10TMG Protective plate weldment 03 B-G057830-4*10 Bolt M4*10 B-G000930-4 Washer 4 B-G00097A-4 Washer 4 SS180T.30.5 Up Hanging pin B-G043290-8 Lock pin 8 RLG61.7...
  • Page 18 24-11 W-05-GE10LM16*1.5ED End Straight Joint M16*1.5-M16*1.5 24-12 W-05-GE12L1/2NPT End Straight Joint NPT1/2-M18*1.5 24-13 W-04-WH12LRKDSOMD High voltage articulated joint G3/8-M18 * 1.5 24-14 W-08-LSQ-PF-G04PDC Flat quick change male 1/2 rubber sleeve 24-15 W-08-LSQ-SF-G04PDC Flat quick change female 1/2 rubber sleeve 24-16 W-05-EV10LR38ED 45 degree combination joint G3/8-M16 * 1.5 RLG61.2TMG...

Table of Contents