Related Manuals for 3Com Quad T1
Summary of Contents for 3Com Quad T1
- Page 1 Quad T1/E1 10/100 Ethernet PCI Network Interface Card Getting Started Guide Part No. 1.024.1973-00...
- Page 2 Quad T1/E1 10/100 Ethernet PCI ® Network Interface Card Getting Started Guide http://www.3com.com/ Part No. 1.024.1973-00...
- Page 3 3Com Corporation reserves the right to revise this documentation and to make changes in content from time 95052-8145 to time without obligation on the part of 3Com Corporation to provide notification of such revision or change. 3Com Corporation provides this documentation without warranty of any kind, either implied or expressed, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose.
-
Page 4: Table Of Contents
ONTENTS VERVIEW Contacting 3Com................... 1-1 Document Conventions................1-2 Product Description ................1-3 Product Compatibility ................1-3 NSTALLATION Installation Tools..................2-1 Installation Procedure ................2-1 ETWORK NTERFACE ABLING Physical Interfaces .................. 3-1 Accessing the User Interface..............3-2 ECHNICAL PECIFICATIONS Technical Specifications ................A-1 Certification .................. -
Page 5: Overview
VERVIEW This chapter provides an overview of: Contacting 3Com Document conventions Product description Product compatibility Contacting 3Com Call the appropriate toll free number listed below for technical support. For European countries that do not have a toll free number listed, call +31 30 602 9900. -
Page 6: Document Conventions
Refer to the Total Control Hub Documentation CD-ROM for more information regarding product warranty. For information about Customer Service, including support, training, contracts, and documentation, visit our website at http://totalservice.3com.com Document These tables list conventions used throughout this guide. Conventions... -
Page 7: Product Description
Configuration of the T1/E1 interface is done via software. Product The Quad T1/E1 10/100 Ethernet PCI NIC is compatible only with PCI Compatibility based Network Application Cards (NACs) such as the EdgeServer Pro and... -
Page 8: Installation
NSTALLATION This chapter contains Quad T1/E1 10/100 Ethernet Peripheral Component Interface (PCI) Network Interface Card (NIC) installation information. Installation Tools To install this NIC in the Total Control chassis, you need a #2 Phillips and flat-head screwdriver. Installation To install this NIC:... - Page 9 2: I HAPTER NSTALLATION 2 Use a #2 Phillips screwdriver to remove the safety panel covering this slot. 3 Insert the NIC between the slot’s upper and lower card guides.
- Page 10 Installation Procedure 4 Slide the NIC into the chassis, until the front of the NIC is flush with the chassis. 5 Use a flat-head screwdriver to tighten the screws on the front panel. 6 Cover any unused chassis slots with safety panels. 7 Install the Network Application Card (NAC) corresponding to this NIC.
-
Page 11: Card Cabling
Quad Network Interface Card (NIC) and instructions for accessing the corresponding Network Application Card (NAC) through the user Interface (UI) port for maintance and software downloads. Physical Interfaces The Quad T1/E1 10/100 PCI NIC has the following interface ports: Callout Number Interface Description –... -
Page 12: Accessing The User Interface
NTERFACE ABLING Accessing the User To access the UI of the corresponding NAC, connect the following cables Interface to the NIC’s console port. Dual T1 DS-1 QUAD T1/E1 10/100 RS-232 ETHERNET PCI NIC RS-232 10 BASE 2 Callout Number Description... -
Page 13: A Technical Specifications
ECHNICAL PECIFICATIONS Technical Specifications Certification Safety EN60950 CB Report including all Country Annexes UL 1950, C/UL IEC 950 AUSTEL EMI/EMC FCC Part 15, Class A, Radiated and Line Conducted EN 55022, Class A, Radiated and Line Conducted EMI, Non-Residential Limits VCCI, Class A EN 50082-1, Electromagnetic Compatibility Telco... -
Page 14: Regulatory Compliance Statements
A: T PPENDIX ECHNICAL PECIFICATIONS Regulatory United States Compliance FCC Part 15 Compliance Statement Statements This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. -
Page 15: T1-E1 Span Ports
Technical Specifications T1/E1 Span Ports Electrical Specification: T1/E1 Long Haul/Short Haul Transceivers Connector: RJ-48C, 8 position modular jack Pinouts 1 = Receive Ring 2 = Receive Ring 3 = N/C 4 = Transmit Ring 5 = Transmit Ring 6 = N/C 7 = N/C 8 = N/C 5ESS... -
Page 16: Current Draw
A: T PPENDIX ECHNICAL PECIFICATIONS Current Draw +5.2 VDC @ 1800mA typical maximum Typical maximum refers to the maximum current draw under most typical configurations. Environment Shipping and Storage ° ° Temperature: -25 to 75 C, -13 to 167 Relative Humidity: 0 to 100%, Non-condensing Operating °... - Page 17 3Com Corporation 5400 Bayfront Plaza P.O. Box 58145 Santa Clara, CA 95052-8145 ©1999 3Com Corporation All rights reserved Printed in the U.S.A. Part No. 1.024.1973-00...
Need help?
Do you have a question about the Quad T1 and is the answer not in the manual?
Questions and answers