Advertisement
Quick Links
FCC Requirement
Changes or modifications not expressly approved by the party responsible for compliance could void the user'
s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired
operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses, and can radiate radio
frequency energy, and if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
FCC WARNING
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
End user must follow the specific operating instructions for satisfying RF exposure compliance. This
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for MUCAR VO8
Summary of Contents for MUCAR VO8
- Page 1 FCC Requirement Changes or modifications not expressly approved by the party responsible for compliance could void the user’ s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
- Page 2 transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The mobile device is designed to meet the requirements for exposure to radio waves established by the Federal Communications Commission (USA). These requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue.
- Page 3 1. Introduction 1.1 Product Profile MUCAR VO8 is a new generation intelligent diagnostic equipment based on Android 8.1. It has broken through original DIY-oriented of MUCAR, bringing outstanding professional and comprehensive diagnosis features including read DTC, clear DTC, read data stream, ECU coding, actuation test, special functions, etc.
- Page 4 1.2 Components & Controls 1.3 Parameters...
- Page 5 2. Quick Start Manual 2.1 Initial Use The following settings should be made when you initially use the device. 2.1.1 Turn on the Machine After pressing the power button, images will be shown on the screen as follow. 2.1.2 Language Setting Select the target language from the languages displayed on the interface.
- Page 6 2.1.3 Connect Wi-Fi The system will automatically search all available Wi-Fi networks. Please connect to the trusted Wi-Fi. Tips: Wi-Fi must be set. If there is no Wi-Fi network is available nearby, you can try "Portable Mobile Hotspot". 2.1.4 Choose Time Zone Choose the time zone of the current location, then the system will automatically configure the time.
- Page 7 2.1.6 Bind the Dongle Input the serial number (SN) to activate the Dongle. You could find the SN on the Dongle. 2.2 Diagnosis Flowchart 2.3 Function Menu After startup, the system will automatically enter the homepage:...
- Page 8 MUCAR VO8 includes functions: Diagnose, Intelligent Diagnosis, TPMS, Maintenance, Module, Remote Assistance, File, Repair Info, Feedback, Store, Update, Settings. 2.4 Charging Follow the steps below to charge the device: 1. Use the charger to connect the device and the power socket to charge.
- Page 9 2. For OBDII/EOBD vehicle, follow the steps below to proceed: A. Plug the VCI dongle into the vehicle’s DLC socket B. Use the OBDII/EOBD extension cable to connect the VCI dongle and DLC socket. 3. For non-OBDII/EOBD vehicle, If the pin of the DLC is damaged or has insufficient power, please try any of the following methods to proceed: A.
- Page 10 OBD I. Such as three PIN like HONDA; 17 PIN like Toyota; 38 PIN like BENZ. At present, all overseas comprehensive diagnostic device of Company’s MUCAR series are equipped with 10 OBD I diagnostic connectors, as shown in the table below:...
- Page 11 B. How to connect OBD I Diagnostic Port The OBD I connector, which was set up to cater for older models of various car brands, has very few current applications as most older cars have been phased out. Cars that produced after 2005 are basically all OBD II connector.
- Page 12 1. Select vehicle type: Enter the "demo" on main diagnostic interface. Tips: The diagnosis menu varies with different vehicles. 2. After the connection is successful, the screen will enter the following interface. 3.1.2 Health Report It enables you to quickly access all the electronic control units of the vehicle and generate a detailed report about vehicle health.
- Page 13 Click "Report" to generate a vehicle health report. 3.1.3 System Scan Automatically scan all systems of the vehicle and use to determine which electronic control units are fitted to this vehicle.
- Page 14 3.1.4 System Selection After selecting a system, it automatically sends a command whether this electronic control unit exists or not, and also determines which type of electronic control unit it is. Choose the system: “PCM” (e.g.), and the screen will enter the function menu. Tips: The diagnosis menu varies with different vehicles.
- Page 15 A. Version Information As shown in the picture, “Version Information” to read the current version information of the car ECU. B. Read Fault Code This function is to read the DTC in the ECU memory, helping maintenance personnel to quickly identify the cause of the vehicle breakdown.
- Page 16 D. Read Data Stream This option lets you view and capture (record) real-time Live Data of ECU. This data, including current operating status for parameters and/or sensor information, can provide insight on overall vehicle performance. It can also be used to guide vehicle maintenance. Select all and tap "OK"...
- Page 17 beyond the specified value, the system will alarm. [Compare To select the sample DS file. All the values you customized and saved in Sample] process of DS sampling will be imported into the Standard Range column for your comparison. Note: Before executing this function, you have to sample the values of data stream items and save it as a sample Data Stream file.
- Page 18 VIN code to gain the car information. 3.3 Maintenance MUCAR VO8 supports common maintenance and reset functions, namely, Oil Reset, Elec. Throttle Adaption, IMMO Service, Injector Coding, Brake-pad Reset, Steering Angle Reset, ABS Bleeding, AFS Reset, Battery Matching, A/T Learning, DPF Regeneration, EGR Adaption, TPMS Reset, Sunroof Initialization, Suspension...
- Page 19 gearbox, steering column, end tie rod, steering knuckle), performing four-wheel alignment, or recovering car body, you must reset the steering angle. 3.3.4 Battery Matching This function enables you to perform a resetting operation on the monitoring unit of vehicle battery, in which the original low battery fault information will be cleared and battery matching will be done.
- Page 20 To prevent the car being used by unauthorized keys, the anti-theft key matching function must be performed so that the immobilizer control system on the car identifies and authorizes remote control keys to normally use the car. When the ignition switch key, ignition switch, combined instrument panel, ECU, BCM, or remote- control battery is replaced, anti-theft key matching must be performed.
- Page 21 speed, not waking up the door opening network, and disabling the remote-control key, etc. At this time, the transport mode needs to be deactivated to restore the vehicle to normal. 3.3.20 A/F Reset This function is applied to set or learn Air/Fuel ratio parameters. 3.3.21 Stop/Start Reset This function is used to open or close the automatic start-stop function via setting the hidden function in ECU (provided that the vehicle has a hidden function and supported by hardware).
- Page 22 TPMS activation, programming and learning. A. Programming: to program sensor data to a new MUCAR sensor, so as to replace a sensor that is in low battery and does not function properly. There are three sensor programming methods available: Automatic, manual, and via activation replication.
- Page 23 3.5 Module 3.5.1 Supported Accessories The device supports optional function modules, list as below: Name Image Description Video Ultra long custom coil pipeline design, Scope flexible bending with durable materials, suitable for a variety of complex environments. Multiple uses with 3 kinds of special connectors (Hook, side view mirror, magnet).
- Page 24 Scope Equipped with 4 channels 100MHz bandwidth, sampling rate reaches up to 1GS/s. Combined with the device screen to achieve full touch control operation. Special automatic maintenance and detection menu and highdefinition waveform display make it more convenient to use. Application scenarios: Scope box can accurately determine the problems of sensors, actuators, control modules or...
- Page 25 3.6 Remote Assistance In this function, you can request remote assistance through third-party software. By sending your device ID number to the remote technician or after-sales personnel, you can authorize the other party to remotely operate the device, so as to guide you to the problems encountered in the process of using the device. 3.7 File It is used to record and establish the file of the diagnosed vehicles.
- Page 26 3.8 Repair Info Tap "Repair Info" on the homepage, the following page will appear. 3.8.1 OBD Fault Code Library You can enquire the definition of OBD fault codes. 3.8.2 Learnings You can view the operation playback of the special functions of each brand model, to help users study the operation of the special functions online without connecting the vehicle.
- Page 27 If you encounter an unresolved problem or diagnostic software bug during diagnosis, you can revert the most recent 20 test records to MUCAR Team. When we receive your feedback, we will analyze and troubleshoot it in a timely manner, to improve the quality of our products and user experience. Tap Feedback, the below pop- up message will appear: Tap OK to enter the vehicle diagnostic feedback selection screen.
- Page 28 History: Tap to view all diagnostic feedback reverted and the processing progress. 3.10 Store It supports the purchase of FULL SOFTWARE PACKAGE. Tips: The full software package includes update license for 100+ vehicle diagnosis software and 34 maintenance software. 3.11 Update In order to let you enjoy better functions and upgrade services, we recommend you make software upgrades irregular.
- Page 29 Upgradeable software: A list of software that can be upgraded to newer versions. Upgraded software: A list of software that has been downloaded. Note: During the upgrade, please keep normal network connection. Upgrade many software may take a few minutes, please wait. If you need to cancel certain software, please enter setting ->...
- Page 30 4.3 Customer Management Manage information of all customers, who conduct vehicle diagnostic on this equipment and display in turn. 4.4 Help There are some frequently asked Q&A. 4.5 Diagnostic Software Clear This option can clear some unused diagnostic software and free up the storage space. PLEASE USE IT WITH CAUTION.
- Page 31 When connecting with other modules, it must use the HOST MODE. If you need to connect to a computer to access the pictures or recorded data stored in the device, you can select DEVICE MODE. 4.9 Screen Shots Switch from , and appears, at which point the function of “Screen shots”...
- Page 32 4.12 Automatically Send Reports Input an e-mail which is available for receiving all the diagnostic reports, you can decide to use this function or not by switching 4.13 Basic Settings The alternation of Language, Time Zone, Sleep Time and Unit are available here. 4.14 Hotkey Setting Including: Wi-Fi, Bluetooth, screen recording, screenshot, screen flip, brightness, sound and Customer Service.
- Page 33 1. Q: Can I use the same type of charger to charge the tablet? A: No, please use original charger. Our company is not responsible for any damage and economic loss caused by using charger, which is not provided by MUCAR. 2. Q: How to save power? A: Please turn off the screen while the device isn’t used, set a shorter standby time, and decrease the...
- Page 34 receive the verification code again. verification code during the registration. 5. Q: Why can’t I log in? Possible reasons Solutions The device is not Please make sure the network is connected to the connected. network. The username or Check the username and password. password is Contact after-sales service or regional incorrect.
- Page 35 8. Q: Why can’t I log in? Possible reasons Solutions The device is not Check the network connection. connected to the network. The username or Check the username and password. password is wrong The device has not Uninstall irrelevant applications and enough memory delete uncommonly used vehicle software (enter setting ->...
- Page 36 The compensation for dashboard damage caused by the defect of this equipment is limited to repair or replacement. MUCAR does not bear any indirect and incidental losses. MUCAR will judge the nature of the equipment damage according to its prescribed inspection methods.
Need help?
Do you have a question about the VO8 and is the answer not in the manual?
Questions and answers