Table of Contents
Advertisement
Quick Links
r e s t r i c t e d
EZ-USB™ FX10 DVK (KIT_FX10_FMC_001) kit
guide
About this document
Scope and purpose
The EZ-USB™ FX10 DVK (KIT_FX10_FMC_001) kit enables the development of applications based on
EZ-USB™ FX10 USB 3.2 Gen 2X1 device controller (CYUSB4014-BZXI) for streaming video and audio seamlessly
to the USB host using the off-the-shelf FPGA add-on board and camera modules.
Intended audience
This document is intended for the EZ-USB™ FX10 DVK (KIT_FX10_FMC_001) kit users.
User guide
Please read the sections "Important notice" and "Warnings" at the end of this document
002-39170 Rev. *B
www.infineon.com
2025-03-21
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Infineon Technologies EZ-USB FX10 DVK
Summary of Contents for Infineon Technologies EZ-USB FX10 DVK
-
Page 1: About This Document
r e s t r i c t e d EZ-USB™ FX10 DVK (KIT_FX10_FMC_001) kit guide About this document Scope and purpose The EZ-USB™ FX10 DVK (KIT_FX10_FMC_001) kit enables the development of applications based on EZ-USB™ FX10 USB 3.2 Gen 2X1 device controller (CYUSB4014-BZXI) for streaming video and audio seamlessly to the USB host using the off-the-shelf FPGA add-on board and camera modules. -
Page 2: Important Notice
Infineon Technologies. The design of the Evaluation Boards and Reference Boards has been tested by Infineon Technologies only as described in this document. The design is not qualified in terms of safety requirements, manufacturing and operation over the entire operating temperature range or lifetime. -
Page 3: Safety Precautions
r e s t r i c t e d EZ-USB™ FX10 DVK (KIT_FX10_FMC_001) kit guide Safety precautions Safety precautions Note: Please note the following warnings regarding the hazards associated with development systems. Table 1 Safety precautions Caution: The evaluation or reference board contains parts and assemblies sensitive to electrostatic discharge (ESD). -
Page 4: Table Of Contents
r e s t r i c t e d EZ-USB™ FX10 DVK (KIT_FX10_FMC_001) kit guide Table of contents Table of contents About this document ........................1 Important notice ..........................2 Safety precautions .......................... 3 Table of contents ..........................4 Introduction .......................... -
Page 5: Introduction
r e s t r i c t e d EZ-USB™ FX10 DVK (KIT_FX10_FMC_001) kit guide Introduction Introduction The EZ-USB™ FX10 DVK (KIT_FX10_FMC_001) kit is based on the EZ-USB™ FX10 product family of Infineon’s USB 10 Gbps device controllers. EZ-USB™ FX10 is a family of USB 10 Gbps peripheral controllers targeting the next-generation USB applications in camera, video, imaging, and data acquisition markets. -
Page 6: Download Kit Documents And Hardware Design Files
r e s t r i c t e d EZ-USB™ FX10 DVK (KIT_FX10_FMC_001) kit guide Introduction Download kit documents and hardware design files Download the KIT_FX10_FMC_001 kit documents and the hardware design files from the EZ-USB™ FX10 kit webpage. The documents include a quick start guide (QSG), kit user guide (this document), and release notes. The hardware design files include schematics, bill of materials (BOM), and layout files. -
Page 7: Ez-Usb™ Fx10 Baseboard Features
r e s t r i c t e d EZ-USB™ FX10 DVK (KIT_FX10_FMC_001) kit guide Introduction Figure 2 EZ-USB™ FX10 baseboard – bottom view EZ-USB™ FX10 baseboard features EZ-USB™ FX10 controller • Two QSPI SPI flash • Onboard regulators: 1.8 V and 3.3 V DC-DC switching regulators •... -
Page 8: Installing The Kit Software
r e s t r i c t e d EZ-USB™ FX10 DVK (KIT_FX10_FMC_001) kit guide Installing the kit software Installing the kit software Download the EZ-USB™ FX10 SDK from the EZ-USB™ FX10 kit webpage. Install the following software. The installation of the following software may require administrator privileges. EZ-USB™... -
Page 9: Kit_Fx10_Fmc_001 System Design
r e s t r i c t e d EZ-USB™ FX10 DVK (KIT_FX10_FMC_001) kit guide KIT_FX10_FMC_001 system design KIT_FX10_FMC_001 system design The EZ-USB™ FX10 baseboard is bus-powered and needs a USB-C cable to connect to the PC. To demonstrate the full functionality of the kit and FPGA, the add-on board must be connected to the EZ-USB™... -
Page 10: Kit_Fx10_Fmc_001 Ez-Usb™ Fx10 Dvk Design Details
r e s t r i c t e d EZ-USB™ FX10 DVK (KIT_FX10_FMC_001) kit guide KIT_FX10_FMC_001 system design KIT_FX10_FMC_001 EZ-USB™ FX10 DVK design details The KIT_FX10_FMC_001 EZ-USB™ FX10 DVK consists of the following: EZ-USB™ FX10 silicon (CYUSB4014-BZXI) • Two external QSPI Flash modules •... -
Page 11: Power Supply
The kit is bus-powered. VBUS supply from the host PC can be disconnected from the kit by removing the jumper from connector J1 pin 1-2. The board consists of two IR3883MTRPBF regulators from Infineon Technologies. It is a DC-DC buck switching regulator rated for 3 A. With a 16PQFN package, the regulator features overvoltage protection, overcurrent protection, and overtemperature protection. -
Page 12: Gpio Interface Connector (J5)
r e s t r i c t e d EZ-USB™ FX10 DVK (KIT_FX10_FMC_001) kit guide KIT_FX10_FMC_001 system design 3.2.1.7 GPIO interface connector (J5) The kit has a 2X10-pin GPIO connector to interface with GPIO accessory board. All the low-speed peripheral signals of EZ-USB™... -
Page 13: Programming The Kit
r e s t r i c t e d EZ-USB™ FX10 DVK (KIT_FX10_FMC_001) kit guide Programming the kit Programming the kit The KIT_FX10_FMC_001 kit is preprogrammed with the internal colorbar firmware to stream 4K UVC color bar video generated internally inside EZ-USB™ FX10. This allows you to stream the color bar video without the need of an FPGA board. - Page 14 r e s t r i c t e d EZ-USB™ FX10 DVK (KIT_FX10_FMC_001) kit guide Programming the kit Do the following to program the device: Click FX3G2 USB BL > Click Program > Click Internal Flash Figure 6 Program in Control Center application Navigate to the <Drive>\EZ-USB FX10 Release Package\SDK\<project folder>\out folder based on the code example project.
- Page 15 r e s t r i c t e d EZ-USB™ FX10 DVK (KIT_FX10_FMC_001) kit guide Programming the kit Wait for programming to complete. Observe the EZ-USB™ FX10 device detach message in the Log window Figure 8 Programming successful Log window User guide 002-39170 Rev.
-
Page 16: Run The Application (Internal Color Bar)
r e s t r i c t e d EZ-USB™ FX10 DVK (KIT_FX10_FMC_001) kit guide Run the application (internal color bar) Run the application (internal color bar) Viewing the UVC output using windows camera application 1. Follow the instructions in the SDK user guide to build the uvc_inmem project 2. -
Page 17: Viewing The U3V Output (Color Bar) Using Ebus Player Application
r e s t r i c t e d EZ-USB™ FX10 DVK (KIT_FX10_FMC_001) kit guide Run the application (internal color bar) 5. On a USB 3.2 Gen 2X1 host, the frame rate will be ~60 fps. This can be viewed on the serial terminal such as Tera Term. - Page 18 r e s t r i c t e d EZ-USB™ FX10 DVK (KIT_FX10_FMC_001) kit guide Run the application (internal color bar) 4. Open eBus Player application and do the following: a) Go to Select/Connect b) Select the available device. For example, FX3G2 c) Press OK Figure 12 eBus Player settings...
-
Page 19: Troubleshooting
r e s t r i c t e d EZ-USB™ FX10 DVK (KIT_FX10_FMC_001) kit guide Troubleshooting Troubleshooting EZ-USB™ FX10 programming test 1. If EZ-FX™ Control Center is not detecting the EZ-USB™ FX10 device: a) Press and hold the PMODE switch (SW2) b) RESET EZ-USB™... -
Page 20: References
EZ-USB™ FX10 DVK (KIT_FX10_FMC_001) kit guide References References [1] Infineon Technologies AG: EZ-USB™ FX10 kit webpage; Available online [2] Infineon Technologies AG: EZ-USB™ FX10 datasheet; Available online User guide 002-39170 Rev. *B... -
Page 21: Glossary
r e s t r i c t e d EZ-USB™ FX10 DVK (KIT_FX10_FMC_001) kit guide Glossary Glossary active authentication (AA) debug access port Electromagnetic Compatibility Electrostatic discharge Firmware JTAG Joint test action group LVDS Low-voltage differential signaling Pulse density modulation QSPI Quad serial peripheral interface Software development kit... -
Page 22: Revision History
r e s t r i c t e d EZ-USB™ FX10 DVK (KIT_FX10_FMC_001) kit guide Revision history Revision history Document Date Description of changes revision 2023-12-18 Initial release 2025-02-27 Removed GPIO accessory board related topics 2025-03-21 Updated FX10 webpage url User guide 002-39170 Rev. -
Page 23: Disclaimer
81726 Munich, Germany authorized representatives Infineon Technologies, Infineon Technologies’ products may not be used in any applications where a failure of © 2025 Infineon Technologies AG. the product or any consequences of the use thereof can reasonably be expected to result in personal All Rights Reserved.
Need help?
Do you have a question about the EZ-USB FX10 DVK and is the answer not in the manual?
Questions and answers