Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Gill Instruments WindSonic
Summary of Contents for Gill Instruments WindSonic
-
Page 2: Table Of Contents
Connecting to a PC using RS232 (Option 1 Sensor) Power and Communications Cable .... 14 4.6. Connecting WindSonic Option 2 or 3 set for default RS422 to a PC using an RS232 Safe Mode Connection..............................15 Changing an Option 2 or 3 Sensor set for RS232 back to RS422..........16 Connecting to a PC using RS422 (Option 2 or 3) ................. - Page 3 6.11 Analogue Output Conditions ....................... 30 6.12 Analogue Output Conditions ....................... 31 6.13 Error condition reporting ......................31 SDI-12 WindSonic ......................34 7.1. Cable Type ........................... 34 7.2. Cable Length ..........................34 7.3. Connecting to an SDI-12 Interface (Option 4) ................34 ............
-
Page 4: Overview Of Content
• • • • • • • •... -
Page 5: General Notes
Document Version Release Date Key Changes Iss 30 Nov 22 New Manual Template... -
Page 6: Product Overview
2. Product Overview... -
Page 7: Pre-Installation
3. Pre-Installation... -
Page 8: Windsonic Ce, Ukca, Fcc Conformity
• •... -
Page 10: Requirements & Installation
4. Requirements & Installation ➢ ➢ ➢ ➢ ➢ ➢ ➢ ➢ ➢... -
Page 11: Installation Guidelines
Do NOT remove the black “rubber” transducer caps. Warranty is void if the coloured security seal is damaged or removed. • • • ❖ ❖ ❖ • • •... -
Page 14: Connecting To A Pc Using Rs232 (Option 1 Sensor) Power And Communications Cable
Typical PC or RS232 to USB WindSonic Converter Serial Port 9 Way circular connector 9 Way ‘D’ Connector Signal names Pin nos. Signal names Pin no's Cable – 3 twisted pairs Signal Ground Signal Ground Do NOT connect Screen and drain... -
Page 15: Connecting Windsonic Option 2 Or 3 Set For Default Rs422 To A Pc Using An Rs232 Safe Mode Connection
WindSonic Typical 9 Way circular connector 9 Way ‘D’ Connector Signal names Pin nos. Signal names Pin no's Cable – 3 twisted pairs Signal Ground Signal Ground Do NOT connect Screen and drain Chassis at this end wires ground V supply -... -
Page 16: Changing An Option 2 Or 3 Sensor Set For Rs232 Back To Rs422
WindSonic PC with RS422/232 converter 9 Way circular connector Signal names Pin nos. Cable – 4 twisted pairs Signal names TXD+ RXD + TXD – RXD – RXD+ TXD + RXD – TXD – Signal Ground Signal Ground Do NOT connect... -
Page 17: Using Rs485 (2 Wire Point To Point) With Option 2 Or 3 Units
WindSonic PC with RS485 card 9 Way circular connector Signal names Pin nos. Cable – 3 twisted pairs Signal names TXD+ RXD+ T/RXD + TXD – T/RXD – RXD – Signal Ground Signal Ground Do NOT connect Screen and drain wires... -
Page 18: Using The Analogue Output (Option 3)
WindSonic Data logger or 9 Way circular connector Chart recorder Signal names Pin nos. Cable – 3 twisted pairs Signal names Analogue Channel 1 (Speed) Analogue Channel 1 Analogue Channel Analogue Channel 2 2 (Direction) Signal Ground Signal Ground (Analogue Return) -
Page 19: Mechanical
5 Mechanical... -
Page 22: Message Formats
6 MESSAGE FORMATS ➢ ➢ ➢ ➢ ➢ ➢ ➢... - Page 23 ...
- Page 29 ...
- Page 34 7. SDI-12 WindSonic...
- Page 35 Values are dependent on anemometer being used ...
- Page 36 ...
- Page 37 ...
- Page 38 Screen Twisted Pair Cable 5 mm 40 mm Screen drain wires cut flush...
- Page 40 Rear View of Connector...
- Page 43 WindSonic RS232 to USB Converter 9 Way circular connector Signal names Pin nos. Cable – 4 twisted pairs Data Type RXD Data Input TX Data Ouput Signal Ground Signal Ground Do NOT connect Screen and drain wires Chassis ground at this end...
- Page 51 ☺ ♥ Type Q then press ENTER...
- Page 58 ...
- Page 64 Notes: -...
- Page 65 • •...
Need help?
Do you have a question about the WindSonic and is the answer not in the manual?
Questions and answers