Advertisement
9. With the mains supply isolated, wire the power cable into the
unswitched fuse spur then wire the unswitched fuse spur into the
9. With the mains supply isolated, wire the power cable into the
9. With the mains supply isolated, wire the power cable into the
9. With the mains supply isolated, wire the power cable into the
mains supply (see wiring diagram on page 5).
unswitched fuse spur then wire the unswitched fuse spur into the
unswitched fuse spur then wire the unswitched fuse spur into the
unswitched fuse spur then wire the unswitched fuse spur into the
mains supply (see wiring diagram on page 5).
mains supply (see wiring diagram on page 5).
mains supply (see wiring diagram on page 5).
Use two of the 8g x 1" screws to attach the spur to a loft joist.
Use two of the 8g x 1" screws to attach the spur to a loft
Use two of the 8g x 1" screws to attach the spur to a loft
Use two of the 8g x 1" screws to attach the spur to a loft
10. Unit can be wired to a heater enable switch (not included). Wire
joist.
joist.
joist.
into the connection located under the unit (see Page 5, cable not
10. If a wired heater enable switch is required, connect it to the
10. If a wired heater enable switch is required, connect it to the
10. If a wired heater enable switch is required, connect it to the
included) and fit it in an accessible area. Do NOT wire into mains
black heater cable. Mount it in an accessible area of the property.
black heater cable. Mount it in an accessible area of the property.
black heater cable. Mount it in an accessible area of the property.
or any other power source. Use two of the 8g x 1" screws to
Use two of the 8g x 1" screws to attach the switch to the wall.
Use two of the 8g x 1" screws to attach the switch to the wall.
Use two of the 8g x 1" screws to attach the switch to the wall.
attach the switch to the wall.
11. Reconnect the electrical supply to the unit. Air should begin to
11. Reconnect the electrical supply to the unit. Air should begin to
11. Reconnect the electrical supply to the unit. Air should begin to
11. Reconnect the electrical supply to the unit. Air should begin to
flow from the diffuser. Press button 1 to show current air flow rate.
flow from the diffuser. Press button 1 to show current air flow rate.
flow from the diffuser. Press button 1 to show current air flow rate.
flow from the diffuser. Press button 1 to show current air flow rate.
12. Further presses will cycle through the air flow rate settings.
12. Further presses will cycle through the air flow rate settings.
12. Further presses will cycle through the air flow rate settings.
12. Further presses will cycle through the air flow rate settings.
9
9
9
9
11
11
11
Single press
Single press
Single press
AFTER INSTALLATION THE END USER SHOULD
KEEP THIS GUIDE FOR FUTURE REFERENCE
AFTER INSTALLATION THE END USER SHOULD
AFTER INSTALLATION THE END USER SHOULD
AFTER INSTALLATION THE END USER SHOULD
KEEP THIS GUIDE FOR FUTURE REFERENCE
KEEP THIS GUIDE FOR FUTURE REFERENCE
KEEP THIS GUIDE FOR FUTURE REFERENCE
9. With the mains supply isolated, w
unswitched fuse spur then wire the
mains supply (see wiring diagram o
Use two of the 8g x 1" screws to
joist.
10. If a wired heater enable switc
black heater cable. Mount it in an
Use two of the 8g x 1" screws to
11. Reconnect the electrical supply
flow from the diffuser. Press button
12. Further presses will cycle throug
10
10
10
9
10
12
12
12
11
Further presses
Further presses
Further presses
Single press
DO NOT
THROW AWAY
DO NOT
DO NOT
DO NOT
AFTER INSTALLATION THE END USER SHOULD
THROW AWAY
THROW AWAY
THROW AWAY
KEEP THIS GUIDE FOR FUTURE REFERENCE
13
DO N
THROW
12
12
12
Advertisement
Need help?
Do you have a question about the LoftVent Mk2 PIV and is the answer not in the manual?
Questions and answers