Kenwood Go KZM35 Instructions Manual
  1. Manuals
  2. Brands
  3. Kenwood Manuals
  4. Kitchen Appliances
  5. Go KZM35
  6. Instructions manual
Kenwood Go KZM35 Instructions Manual

Kenwood Go KZM35 Instructions Manual

Hide thumbs Also See for Go KZM35:
Table of Contents

Advertisement

Quick Links

Download this manual
Kenwood Go
TYPE: KZM35
instructions

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Go KZM35 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Kenwood Go KZM35

Summary of Contents for Kenwood Go KZM35

  • Page 1 Kenwood Go TYPE: KZM35 instructions...
  • Page 2 English 2 - 19 ´ ¸ ∂ ٢٠ - ٣٨...

  • Page 3: Table Of Contents

    English Safety Plug and Fuse Information Care and Cleaning Part List 8-10 To Use Your Stand Mixer Usage Diagrams and Usage Instructions To Fit and Use Your Splashguard 10-11 12-13 Usage Chart Recipes Tool Adjustment Cord Storage Service and Customer Care Troubleshooting 18-19...

  • Page 4: Safety

    If the plug or cord is damaged it must, for safety reasons, be replaced by Kenwood or an authorised Kenwood repairer in order to avoid a hazard. Always turn the speed control to ‘O’ OFF position and unplug before fitting or removing tools/attachments, after use and before cleaning.

  • Page 5: Plug And Fuse Information

    The maximum rating is based on the mini chopper/mill attachment that draws the greatest load. Other attachments may draw less power. Only use the appliance for its intended domestic use. Kenwood will not accept any liability if the appliance is subject to improper use, or failure to comply with these instructions.

  • Page 6: Care And Cleaning

    Care and Cleaning Always switch off and unplug before cleaning. A little grease may appear at the bowl tool socket when you first use it. This is normal – just wipe it off. Appliance and Outlet Covers Wipe with a damp cloth then dry (including the feet on the underside of the machine). Never use abrasives or immerse in water.

  • Page 8: Parts List

    Parts List...
  • Page 9 Attachment Outlets High-speed outlet Bowl tool socket Mixer High speed outlet cover Mixer head Handle Speed control dial Head release lever Power unit Bowl K-Beater Whisk Dough tool Splashguard Bowl seat pad Measuring spoon Cord storage...

  • Page 10: To Use Your Stand Mixer

    To Use Your Stand Mixer Usage Diagrams and Usage Instructions...
  • Page 11 Important If the mixer head is raised during operation, the machine will stop working straight away. To re-start the mixer, lower the mixer head, turn the speed switch to the ‘O’ position, wait a few seconds and then re-select the speed. The mixer should resume operating straight away.

  • Page 12: Usage Diagrams And Usage Instructions

    Yeast Dried Yeast (the type that needs reconstituting): pour the warm water into the bowl. Then add the yeast and sugar and leave to stand for 10 minutes until frothy. Fresh yeast: crumble into the flour Other types of yeast: follow the manufacturer’s instructions. Put the dough into a greased polythene bag or a bowl covered with a tea towel.
  • Page 13 Important During mixing, ingredients can be added directly to the bowl via the chute of the splashguard. You do not need to remove the splashguard to change tools. Raise the mixer head until it locks. Fit the bowl onto the base. Push the splashguard onto the underside of the mixer head until fully located.

  • Page 14: Usage Chart

    Usage Chart (Mins) (MAX) Total 1–6 5–10 300 g 1.2 kg 1–2 0.5–2 500 g 1–6 5–10 400 g Total 1–4 5–10 750 g 1–6 5–10 Total 1.8 kg...
  • Page 15 (Mins) (MAX) 1–6 1–2 750 ml 1–6 1–2 4-8˚C 760 g 1-1.5 1-1.5 (Mins) (MAX) Total 3–4 800 g 1.290 kg Total 3–4 800 g 1.350 kg Total 4–9 700 g 1.520 kg 1–2 Total 500 g 775 g...

  • Page 16: Recipes

    Recipes White Bread Dough 800 g Flour 9 g Salt 13 g Fast Action Dried Yeast 448 ml Water 15 g Lard or Butter Fit the bowl to the stand mixer. Pour the water into the bowl, followed by the remaining ingredients. Mix on speed 1 for 45 –...

  • Page 17: Tool Adjustment

    Tool Adjustment Usage Diagrams and Usage Instructions Important The tools are set to the correct height for the bowl supplied in the factory and should not require adjustment. However, if you wish to adjust the tool use a suitable sized spanner.

  • Page 18: Cord Storage

    Cord Storage...

  • Page 19: Service And Customer Care

    If your Kenwood product malfunctions or you find any defects, please send it or bring it to an authorised KENWOOD Service Centre. To find up to date details of your nearest authorised KENWOOD Service centre visit www.kenwoodworld.com or the website...

  • Page 20: Troubleshooting

    Troubleshooting Guide Problem Cause Solution The whisk, K-Beater knocks Tool at the wrong height Adjust the height using a against the bottom of the and needs adjusting. suitable spanner – see “Tool bowl or not reaching the Adjustment” section. ingredients in the bottom of the bowl.
  • Page 21 Problem Cause Solution 5) Four flashes per second Triac/PCBA Fault Return control dial to ‘0’. Unplug for a 2 second period, machine, wait for 15 minutes then a 1 second period of Safety FlipFlop Fault before restarting the machine. non-illumination, followed Safety Relay Fault by;...
  • Page 22 Triac/PCBA FlipFlop...
  • Page 23 « » "0" "1" "P" (OFF)
  • Page 24 » « .www.kenwoodworld.com Kenwood KENWOOD KENWOOD www.kenwoodworld.com Kenwood (WEEE)
  • Page 26 •...
  • Page 27 – –...
  • Page 28 – – 4-8˚C – ½ – ½ Total – Total – Total – Total...
  • Page 29 Total – ½– – Total – – Total...
  • Page 32 «O» – «O» (OFF) " " "...
  • Page 37 –...
  • Page 38 (OFF) (OFF) "0" "1" "P" 2004/1935...
  • Page 39 Kenwood Kenwood O’OFF‘ “ ” ¥...
  • Page 42 Kenwood Ltd New Lane Havant Hampshire PO9 2NH kenwoodworld.com © Copyright 2024 Kenwood Limited. All rights reserved 5720071750/1...

This manual is also suitable for:

Go kzm35.000rd

Table of Contents