Kenwood Chef (KVC51), Chef XL (KVL61) - Kitchen Machine Manual

Know your Kenwood Stand Mixer

Safety

• Read these instructions carefully and retain for future reference.
• Remove all packaging and any labels.
• If the plug or cord is damaged it must, for safety reasons, be replaced by Kenwood or an authorised Kenwood repairer in order to avoid a hazard.
• Turn the speed control to 'O' OFF position and unplug before fitting or removing tools/attachments, after use and before cleaning.
• Keep your fingers away from moving parts and fitted attachments.
• Never leave the Stand Mixer unattended when it is operating.
• Never use a damaged appliance. Get it checked or repaired: see 'Service and customer care' section.
• Never operate the Stand Mixer with the head in the raised position.
• Never let the cord hang down where a child could grab it.
• Never let the power unit, cord or plug get wet.
• Never use an unauthorised attachment or more than one attachment at once.
• Never exceed the quantities stated in the maximum capacity chart.
• When using an attachment, read and follow the safety instructions that are supplied with it.
• Take care when lifting this appliance as it is heavy. Ensure the head is correctly latched in the down position and that the bowl, tools, outlet covers and cord are secure before lifting.
• Do not move or raise the mixer head with an attachment fitted as the Stand Mixer could become unstable.
• When moving the appliance always pick up by the pedestal base and mixer head. Do not lift or carry the appliance by the bowl handle.
• Do not operate your appliance near the edge or overhanging the work surface or apply force to an attachment when fitted, as this may cause the unit to become unstable and tip over, which may result in injury.
• Take care when removing bowl tools after extended use as they may get hot.
• Ensure the cord is fully unfolded from the cord storage compartment before using the Stand Mixer.
• Children should be supervised to ensure that they do not play with the appliance.
• Do not operate your appliance near the edge of a work surface.
• The short power-supply cord is used to reduce risk resulting from becoming entangled in or tripping. Extension cords may be used if care is exercised in their use. If an extension cord is used:
  1. The marked electrical rating of the extension cord should be at least as great as the electrical rating of the appliance; and
  2. The cord should be arranged so that it will not drape over the countertop or tabletop where it can be pulled on by children or tripped over unintentionally.
  3. The extension cord should be an earthed-type 3-wire cord. The electrical rating of the appliance is listed on the bottom of the unit.
• Appliances can be used by persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and if they understand the hazards involved.
• Misuse of your appliance can result in injury.
• This appliance shall not be used by children. Keep the appliance and its cord out of reach of children.
• The maximum rating is based on the mini chopper/mill attachment that draws the greatest load. Other attachments may draw less power.
• Only use the appliance for its intended domestic use.
  Kenwood will not accept any liability if the appliance is subject to improper use, or failure to comply with these instructions.

Before using for the first time

• Wash the parts: see 'Care and cleaning' section.

Know your Stand Mixer

Key

Attachment outlets

1. high-speed outlet
2. slow-speed outlet
3. bowl tool socket

Mixer

4. high speed outlet cover
5. mixer head
6. head release lever
7. mixer ready indicator light
8. on/off and speed control
9. power unit
10. bowl
11. slow speed outlet cover
12. cord storage compartment
13. K-beater
14. whisk
15. 1. dough tool (if supplied)
    2. spiral dough tool (if supplied)
16. spatula
17. splashguard (if supplied)
18. splashguard (if supplied)
    1. head shield
    2. splashguard

Note: Spanner shown is for illustration purposes only and is not supplied in pack.

Optional attachments

There are a range of optional attachments available to use with your Stand Mixer.
See the attachment leaflet included in your pack or visit www.kenwoodworld.com to see the full range and how to buy an attachment not included in your pack.

Note: Slow Speed outlet attachments
The slow speed outlet on your Stand Mixer model features the Twist Connection System. It is designed to accept Twist Connection System attachments. When purchasing new attachments for the slow speed outlet you should check compatibility with your Stand Mixer. All Twist Connection System attachments can be identified by the product code which starts with KAX and also by the Twist logo which is visible on packaging. For more information visit www.kenwoodworld.com/twist.

If you own attachments featuring the Bar Connection System you will need to use the KAT002ME adaptor to connect these to the Twist Connection System on your Stand Mixer.

For more information visit www.kenwoodworld.com/twist.

The bowl tools and some of their uses

K-beater

For making cakes, biscuits, pastry, icing, fillings, éclairs and mashed potato.

Whisk

For eggs, cream, batters, fatless sponges, meringues, cheesecakes, mousses, soufflés. Do not use the whisk for heavy mixtures (e.g. creaming fat and sugar) - you could damage it.

Dough Hook

For yeast mixtures only

To use your bowl tools

Ensure the cord is fully unfolded from the cord storage compartment before using the Stand Mixer.

1. Push the head-lift lever down and raise the mixer head until it locks .
2. Fit the bowl on the base and turn clockwise to secure in position.
3. Place the required tool into the socket. Then push up and turn the tool to lock into position.
   Note: If the K-beater or Whisk are not picking up ingredients from the bottom of the bowl refer to the "Tool Adjustment" section.
4. Lower the mixer head by pushing the head release lever down and lower the mixer head until it locks .
5. Plug into the power supply and the 'mixer ready indicator light' will illuminate.
6. Start the machine by turning the speed control to the desired speed setting. Use the pulse (P) position for short bursts of maximum speed.
7. After use, return the speed control to 'O' OFF position and unplug your Stand Mixer.
8. Release the tool by turning clockwise to unlock from the tool socket and then remove.

Hints

• The fold function can be used for folding light ingredients into heavier mixtures for example meringues, mousses, fruit fools, Genoese sponges and soufflés, and to slowly incorporate flour and fruit into cake mixtures. The mixer will operate at a constant slow speed.

Ensure that no bowl tools are fitted or stored in the bowl when using other outlets.

Eggs sizes used = medium sized (Weight 53 – 63g)
* This is for guidance only and will vary depending on the exact recipe and ingredients being processed

To fit and use your Splashguard

Splashguard

1. Raise the mixer head until it locks.
2. Fit the bowl onto the base.
3. Push the splashguard onto the underside of the mixer head until fully located. The hinged section should be positioned as shown.
4. Insert required tool.
5. Lower the mixer head.
   • During mixing, ingredients can be added directly to the bowl via the hinged section of the splashguard .
   • You do not need to remove the splashguard to change tools.
6. Remove the splashguard by raising the mixer head and pushing it down.

Splashguard
The splashguard assembly consists of 2 pieces: the head shield and the splashguard .

• The splashguard cannot be fitted to the bowl unless the shield is fitted.

1. Clip the head shield upwards onto the underside of the mixer head until fully located.
2. Rest the splashguard on the bowl rim and then slide forward until fully located .

Tool Adjustment

K-beater & Whisk

The tools are set to the correct height for the bowl supplied in the factory and should not require adjustment.

However, if you wish to adjust the tool use a suitable sized spanner:
TYPE KVC51 = 15mm
TYPE KVL61 = 19mm

Then follow the instructions below:

1. Unplug the appliance.
2. Raise the mixer head and insert the whisk or beater.
3. Lower the mixer head. If the clearance needs to be adjusted, raise the mixer head and remove the tool. Ideally the whisk and K-beater should be almost touching the bottom of the bowl .
4. Using a suitable spanner loosen the nut sufficiently to allow adjustment of the shaft . To lower the tool closer to the bottom of the bowl, turn the shaft anticlockwise. To raise the tool away from the bottom of the bowl turn the shaft clockwise.
5. Re-tighten the nut.
6. Fit the tool to the mixer and lower the mixer head. (Check its position see points above).
7. Repeat the above steps as necessary until the tool is set correctly. Once this is achieved tighten the nut securely.

• Note: Spanner shown is for illustration purpose only.

Dough Hook

This tool is set at the factory and should require no adjustment.

Care & Cleaning

• Always switch off and unplug before cleaning.
• A little grease may appear at the slow speed outlet when you first use it. This is normal – just wipe it off.

Power Unit And Outlet Covers

• Wipe with a damp cloth, then dry.
• Never use abrasives or immerse in water.
• Store excess cord into the cord storage compartment at the back of the machine.

Bowl

• Wash by hand, then dry thoroughly or wash in the dishwasher.
• Never use a wire brush, steel wool or bleach to clean your stainless steel bowl. Use vinegar to remove limescale.
• Keep away from heat (cooker tops, ovens, microwaves).

Whisk & Splashguard

• Wash by hand, then dry thoroughly or wash in the dishwasher.

K beater & Dough Tool

• Wash by hand, then dry thoroughly or wash in the dishwasher.

Recipe

chilli marinade

200g cold clear runny honey (refrigerated overnight)
1 chilli (whole)
20g (1tsp) crunchy peanut butter
Seasoning

1. Place all the ingredients into the mini chopper/mill.
2. Fit the attachment to the Stand Mixer and allow the ingredients to settle around the blade.
3. Switch to pulse for 4 seconds.
4. Use as required.

Service and Customer Care

If you experience any problems with the operation of the appliance, before calling for assistance refer to the troubleshooting guide or visit www.kenwoodworld.com.

If you need help with:

• using your appliance
• servicing or repairs (in or out of guarantee)
  call Kenwood customer care on 0345 222 0458. Have your model number (e.g. KVC51, or KVL61) and date code (5 digit code e.g. 21T04) ready. They are on the underside of the power unit.
• spares and attachments
  call 0844 557 3653.

other countries

• If you experience any problems with the operation of your appliance, before requesting assistance refer to the "Troubleshooting guide" section in the manual or visit www.kenwoodworld.com.
• Please note that your product is covered by a warranty, which complies with all legal provisions concerning any existing warranty and consumer rights in the country where the product was purchased.
• If your Kenwood product malfunctions or you find any defects, please send it or bring it to an authorised KENWOOD Service Centre. To find up to date details of your nearest authorised KENWOOD Service centre visit www.kenwoodworld.com or the website specific to your Country.
• Made in China.

IMPORTANT INFORMATION FOR CORRECT DISPOSAL OF THE PRODUCT IN ACCORDANCE WITH THE EUROPEAN DIRECTIVE ON WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT (WEEE)

At the end of its working life, the product must not be disposed of as urban waste. It must be taken to a special local authority differentiated waste collection centre or to a dealer providing this service. Disposing of a household appliance separately avoids possible negative consequences for the environment and health deriving from inappropriate disposal and enables the constituent materials to be recovered to obtain significant savings in energy and resources. As a reminder of the need to dispose of household appliances separately, the product is marked with a crossed-out wheeled dustbin.

Troubleshooting guide

Problem	Cause	Solution
The whisk or K-beater knocks against the bottom of the bowl or not reaching the ingredients in the bottom of the bowl.	Tool at the wrong height and needs adjusting.	Adjust the height using a suitable spanner – see "Tool Adjustment" section.
Slow speed attachment cannot be fitted.	Check your attachment is compatible for use with your model. Twist connection system required (Model KAX)	Attachment must have the KAX twist connection system to fit the outlet. If you own attachments featuring the Bar Connection System you will need to use the KAT002ME adaptor to connect these to the Twist Connection System on your Stand Mixer. For more information visit www.kenwoodworld.com/twist
'Mixer ready indicator light' flashing when Stand Mixer first plugged in.	Speed control not in the 'O' position. Mixer head in the raised position or not locked down correctly.	Check and turn speed control to the 'O' position. Check Stand Mixer head is locked down correctly.
The Stand Mixer stops during operation. 'Mixer ready indicator light' flashing rapidly.	Overload protection or overheat system activated. Maximum capacity exceeded.	Unplug and check for obstruction or overloading. Turn the speed control to "O" and then restart. If the machine will not operate, remove some of the ingredients to reduce the load and restart. If this still does not resolve the problem, unplug and allow to stand for 15 minutes. Plug in and reselect the speed. If the machine does not restart following the above procedure contact "customer care" for further advice.
'Mixer ready indicator light' off whilst machine plugged in.	Stand Mixer has been left plugged in for more than 30 minutes without being operated and has gone into Standby mode.	Turn the speed control to 'min' then return to 'O' to reset the machine.