Related Manuals for Baumer PMG93 CAM
Summary of Contents for Baumer PMG93 CAM
- Page 1 Manual PMG93 CAM | Parameterization with web interface Baumer Germany GmbH & Co. KG Bodenseeallee 7 DE-78333 Stockach www.baumer.com...
-
Page 2: Table Of Contents
Parameterization import / export ....................22 Web interface ..........................22 Safety instructions ........................23 10.1 Web interface ..........................23 10.2 Default / factory settings ......................... 23 Firmware update ........................... 24 Baumer_PMG93CAM_Handbuch-Webinterface_EN.docx 2/26 Baumer Germany GmbH & Co. KG 07/2024 Technical amendments reserved... - Page 3 Cam encoder reboot ........................25 12.1 Web interface ..........................25 Restore default ..........................26 13.1 Switch Factory settings in terminal box ..................26 13.2 Web interface ..........................26 Baumer_PMG93CAM_Handbuch-Webinterface_EN.docx 3/26 Baumer Germany GmbH & Co. KG 07/2024 Technical amendments reserved...
- Page 4 Baumer Germany GmbH & Co. KG rejects any liability for the information compiled in the present manual. Baumer Germany GmbH & Co KG nor the author will accept any liability for direct or indirect damages resulting from the use of the present information.
-
Page 5: General Information
1 General information 1.1 Purpose of the manual This manual is part of the technical documentation for the digital cam encoder PMG93 CAM and describes the parameterization of the device. The manual is part of the product and must be kept in its immediate vicinity, accessible to personnel at all times. -
Page 6: Network Connection Of The Cam Encoder
M12 (A1) as encoder connector. The connection is made either peer-to-peer (see Fig. 1) or via router or switch (see Fig. 2). Fig. 1 Peer-to-peer connection Fig. 2 Connection via router or switch Baumer_PMG93CAM_Handbuch-Webinterface_EN.docx 6/26 Baumer Germany GmbH & Co. KG 07/2024 Technical amendments reserved... -
Page 7: Web Interface
) is always visible, no matter which mode is currently applied. Fig. 3 PMG93 CAM Cam encoder name Email request for support. Serial number display. Link to the Baumer website. Selection of the language of the user interface. Baumer_PMG93CAM_Handbuch-Webinterface_EN.docx 7/26 Baumer Germany GmbH & Co. KG 07/2024 Technical amendments reserved... -
Page 8: Menu Bar
In Monitoring mode, the cam encoder parameters are presented in section Active Parameters (3 in Fig. 3 In Parameterization mode, parameter setting is made in the section Active parameters. Baumer_PMG93CAM_Handbuch-Webinterface_EN.docx 8/26 Baumer Germany GmbH & Co. KG 07/2024 Technical amendments reserved... -
Page 9: Section Result Over Time
) presents the actual measured values of the cam encoder. Clicking one Fig. 3 of the measured values will have it appear in the form of a diagram in section Result over time. Baumer_PMG93CAM_Handbuch-Webinterface_EN.docx 9/26 Baumer Germany GmbH & Co. KG 07/2024 Technical amendments reserved... -
Page 10: Footer
Error present at the switching output. 2.2 Monitoring mode Monitoring mode presents the signal selected in Measured values in graphical form over time. Monitoring mode does not enable a change in parameterization. Baumer_PMG93CAM_Handbuch-Webinterface_EN.docx 10/26 Baumer Germany GmbH & Co. KG 07/2024 Technical amendments reserved... -
Page 11: Parameterization Mode
Note: Alternatively, use the sliders at the dotted lines ( resp. ) for parameterization of the switching outputs. For doing so, select the desired cam switch in the selection below the visualization. Baumer_PMG93CAM_Handbuch-Webinterface_EN.docx 11/26 Baumer Germany GmbH & Co. KG 07/2024 Technical amendments reserved... - Page 12 Fig. 4 Cam switch with hysteresis Baumer_PMG93CAM_Handbuch-Webinterface_EN.docx 12/26 Baumer Germany GmbH & Co. KG 07/2024 Technical amendments reserved...
-
Page 13: Mode Device Configuration
Enter current password. New password Enter new password. Validate new password Validate new password. Web interface version Version number of the web interface. Show licenses Show all licenses in use. Baumer_PMG93CAM_Handbuch-Webinterface_EN.docx 13/26 Baumer Germany GmbH & Co. KG 07/2024 Technical amendments reserved... -
Page 14: Mode Diagnostic Data
Operating time (since Presents the operating time since last power-on (in days, hours, minutes). power on) Total operating time Presents the operating time since first power-on (in days, hours, minutes). Baumer_PMG93CAM_Handbuch-Webinterface_EN.docx 14/26 Baumer Germany GmbH & Co. KG 07/2024 Technical amendments reserved... -
Page 15: Electronic Product Label
Queries are enabled via the web interface. 3.1 Web interface Mode Device configuration (see chapter 2.4) in section Sensor Info: Fig. 5 Web interface: Sensor Info Baumer_PMG93CAM_Handbuch-Webinterface_EN.docx 15/26 Baumer Germany GmbH & Co. KG 07/2024 Technical amendments reserved... -
Page 16: Network Configuration
The following network default settings are applied at delivery and after restore default (see chapter 13): IP address: 192.168.0.250 Subnet mask: 255.255.255.0 Standard gateway: 0.0.0.0 Host name: PMG93- + <2 last bytes of the Mac address in hex format> DHCP: Baumer_PMG93CAM_Handbuch-Webinterface_EN.docx 16/26 Baumer Germany GmbH & Co. KG 07/2024 Technical amendments reserved... -
Page 17: Time Synchronization
5.2 Default values / factory settings The following default time server settings will be applied at delivery and after restore default (see chapter 13): NTP: Time server 1: 0.0.0.0 Time server 2: 0.0.0.0 Baumer_PMG93CAM_Handbuch-Webinterface_EN.docx 17/26 Baumer Germany GmbH & Co. KG 07/2024 Technical amendments reserved... -
Page 18: Switching Outputs
An error being present at the switching output is indicated and the output is opened. The switching output will only be accessible again after cam encoder power OFF and ON again. Baumer_PMG93CAM_Handbuch-Webinterface_EN.docx 18/26 Baumer Germany GmbH & Co. KG 07/2024 Technical amendments reserved... -
Page 19: How To - Disable Switching Output
Set the slider next to the output, e.g. Cam switch 1, to OFF. How to - enable switching output 6.3.2 Set the slider next to the output name, e.g. Cam switch 1, to ON. Baumer_PMG93CAM_Handbuch-Webinterface_EN.docx 19/26 Baumer Germany GmbH & Co. KG 07/2024 Technical amendments reserved... -
Page 20: Preset Function
For repeated trigger of a preset event via signal input PRE, latter must be LOW for at least 50 ms between two preset commands. 7.3 Default / factory settings Preset is 0 at delivery and after restore default (see chapter 13). Baumer_PMG93CAM_Handbuch-Webinterface_EN.docx 20/26 Baumer Germany GmbH & Co. KG 07/2024 Technical amendments reserved... -
Page 21: Cam Hysteresis
). The parameter is immediately applied after confirmation with Enter or when quitting Fig. 10 the field. Fig. 10 Cam hysteresis 8.2 Default / factory settings Hysteresis is 25 at delivery and after restore default (see chapter 13). Baumer_PMG93CAM_Handbuch-Webinterface_EN.docx 21/26 Baumer Germany GmbH & Co. KG 07/2024 Technical amendments reserved... -
Page 22: Parameterization Import / Export
Import button. Parameterization is adopted during file import. Fig. 11 Web interface: Parameterization import & export Note: Cam encoder restart is recommended but not mandatory after parameterization import. Baumer_PMG93CAM_Handbuch-Webinterface_EN.docx 22/26 Baumer Germany GmbH & Co. KG 07/2024 Technical amendments reserved... -
Page 23: Safety Instructions
(twice to confirm). Pressing the Store to Sensor button will have the new password applied. Fig. 12 Web interface: Security 10.2 Default / factory settings Password at delivery and after restore default is pmg93admin (see chapter Fehler! Verweisquelle konnte nicht gefunden werden.). Baumer_PMG93CAM_Handbuch-Webinterface_EN.docx 23/26 Baumer Germany GmbH & Co. KG 07/2024 Technical amendments reserved... -
Page 24: Firmware Update
7. Please reboot to make sure that all processes have been executed correctly. Fig. 13 Web interface: Uploading new firmware Fig. 14 Web interface: Uploading new firmware - file selection Baumer_PMG93CAM_Handbuch-Webinterface_EN.docx 24/26 Baumer Germany GmbH & Co. KG 07/2024 Technical amendments reserved... - Page 25 For cam encoder reboot click on Reboot Sensor. The button is available in mode Device configuration (see chapter 2.4) under Web interface & Firmware (see Fig. 15). Fig. 15 Web interface: cam encoder reboot Baumer_PMG93CAM_Handbuch-Webinterface_EN.docx 25/26 Baumer Germany GmbH & Co. KG 07/2024 Technical amendments reserved...
-
Page 26: Restore Default
Alternatively, restore default via button Factory Reset in mode Device Configuration (see chapter 2.4) under item Web interface & Firmware (see Fig. 18). Pressing the button will restore default followed by cam encoder reboot. Fig. 18 Web interface: Factory reset Baumer_PMG93CAM_Handbuch-Webinterface_EN.docx 26/26 Baumer Germany GmbH & Co. KG 07/2024 Technical amendments reserved...
Need help?
Do you have a question about the PMG93 CAM and is the answer not in the manual?
Questions and answers