Download Print this page

Safety Instructions - NAIM PREAMPLIFIERS Manual

Preamplifiers, integrated amplifiers, power amplifiers

Advertisement

saFeTY InsTruCTIons

In order to comply with current european safety regulations
it is essential that the naim loudspeaker connectors
supplied with amplifiers and loudspeakers are used.
Do not under any circumstances allow anyone to modify
your naim equipment without first checking with the factory,
your retailer, or your distributor. unauthorised modifications
will invalidate your guarantee.
equipment must not be exposed to dripping or splashing
and no objects filled with liquid, such as vases, should be
placed on the equipment.
For your own safety do not under any circumstances open
naim equipment without first disconnecting it from the
mains.
warning: an apparatus with CLass I construction shall
be connected to a mains socket outlet with a protective
earthing connection.
where the mains plug or an appliance coupler is used as
the disconnect device, the disconnect device shall remain
readily operable. To disconnect the equipment from the
mains remove the mains plug from the mains outlet.
The following label is attached to all mains powered
equipment:
w a r n I n G
noTe
This equipment has been tested and found to comply
with the relevant emC and safety standards, and, where
applicable, also complies with the limits for a class B digital
device, pursuant to Part 15 of the FCC rules.
These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio
frequency and, if not installed and used in accordance
with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or
television reception, which can be determined by turning
off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the
receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult your Naim retailer or an experienced radio/TV
technician for help.
THIs aPParaTus
musT Be earTHeD
C onte nt s
Page
section
e1
1
Connections
e1
2
mains Power
e2
3
General Installation
e3
4
naC 552 Introduction and Installation
e4
5
naC 552 Controls and Connections
e5
6
naC 552 specification
e6
7
naC 252 Introduction and Installation
e6
8
naC 252 Controls and Connections
e7
9
naC 252 specification
e8
10
naC 282 Introduction and Installation
e8
11
naC 282 Controls and Connections
e10
12
naC 282 specification
e11
13
naC 202 Introduction and Installation
e11
14
naC 202 Controls and Connections
e12
15
naC 202 specification
e13
16
naC 152 Xs Introduction and Installation
e14
17
naC 152 Xs Controls and Connections
e16
18
naC 152 Xs specification
e17
19
supernait Introduction and Installation
e19
20
supernait Controls and Connections
e21
21
supernait specification
e22
22
nait Xs Introduction and Installation
e23
23
nait Xs Controls and Connections
e25
24
nait Xs specification
e26
25
nait 5i Introduction and Installation
e26
26
nait 5i Controls and Connections
e27
27
nait 5i specification
e28
28
Preamplifier and Integrated amplifier
operation
e31
29
r-com remote Handset
e32
30
narCom 4 remote Handset
e33
31
naP 500 Installation and operation
e34
32
naP 500 Connections
e34
33
naP 500 specification
e35
34
naP 300 Installation and operation
e36
35
naP 300 Connections
e36
36
naP 300 specification
e37
37
naP 250 Installation and operation
e37
38
naP 250 Connections
e37
39
naP 250 specification
E38
40
NAPV 145 Installation and Operation
E38
41
NAPV 145 Connections
E38
42
NAPV 145 Specification
e39
43
naP 200 Installation and operation
e39
44
naP 200 Connections
e39
45
naP 200 specification
e40
46
naP 155 Xs Installation and operation
e40
47
naP 155 Xs Connections
e40
48
naP 155 Xs specification
E41
49
NAPV 175 Installation and Operation
E41
50
NAPV 175 Connections
E42
51
NAPV 175 Specification
e42
52
Declarations of Conformity

Advertisement

loading