Baumer HXC13 Quick Start Manual

Quick Start Guide
HXC13 - Digital High Speed Camera
Safety
Conformity:
CE, FCC Part 15 Class B, RoHS
FCC – Class B device
N : This equipment has been tested and found to
ote
comply with the limits for a Class B digital device, pursu-
ant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interfer-
ence in a residential environment. This equipment gener-
ates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructios,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not
occure in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which can be determined by turning the equipment off an
on, the user is encouraged to try to correct the interference
by one or more of the following measures:
▪ Reorient or relocate the receiving antenna.
▪ Increase the separation between the equipment and the
receiver.
▪ Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
▪ Consult the dealer or an experienced radio/TV technician
for help.
Further Information
For further information on our products visit www.baumer.com
For technical issues, please contact our technical support:
support@baumeroptronic.com · Phone +49 (0)3528 4386-0 · Fax +49 (0)3528 4386-86
© Baumer Optronic GmbH · Badstrasse 30 · DE-01454 Radeberg, Germany
Technical data has been fully checked, but accuracy of printed matter not guaranteed.
Subject to change without notice. Printed in Germany 04/12. V1.1
Product Specification
HXC13 – High speed CMOS camera for advanced industrial vision applications
▪ High resolution: 1280x1024 pixel CMOS Sensor
▪ up to 1024 gray levels (10bit resolution)
▪ up to 500 full frames/sec
▪ arbitrary region of interest
▪ very high sensitivity
▪ 14 µm square pixels
▪ electronic "Freeze Frame" shutter
▪ low blooming
▪ programmable via CameraLink
▪ asynchronous trigger
▪ small, compact housing
▪ wide power supply range
Installation
Installation using
Camera Link ® BASE:
▪ Connect the camera using
an appropriate cable to the
framegrabber board on your
Safety Precautions
PC using the lower mdr-26
jack on the camera side
Notice
▪ If required, connect a strobe
See user´s Guide for the comple-
te safety instructions! to the HIROSE connector
▪ Connect the camera to
power supply
▪ Protect the sensor from dirt and
moisture.
▪ Never open the camera housing.
▪ Avoid camera contamination by
foreign objects.
Installation using
Environmental requirements:
Camera Link MEDIUM /
®
Storage temp. -10°C ... +70°C
FULL:
Operating temp. +5°C ... +50°C
Housing temp. max. +50°C
▪ Connect the camera using
Humidity 10 % ... 90 %
two appropriate cables to
Non-condensing
the framegrabber board on
your PC (this configuration
requires the BASE and the
FULL Camera Link
▪ If required, connect a strobe
to the HIROSE connector
▪ Connect the camera to
power supply
11037740
serial interface
®
Installation sample
1 - Framegrabber board; 2 - Camera Link
cable; 3 - Cable for strobe; 4 - Power cable
line)
®
Installation sample
1 - Framegrabber board; 2 - Camera Link
cable; 3 - Cable for strobe; 4 - Power cable
Dimensions
● HXC13 (11008792)
8 x 12-M4 depth 6
63
Dimensions
● HXC13-F (11008791)
8 x 12-M4 depth 6
®
63
®
33
33