Advertisement

SPECIFICATIONS
Part Number: 118593
Set Up Size: 96"L x 61"W x 75"H
Packed Size: 61"L x 35"W x 23"H
W e i g h t: 92lbs.
Fishable Area: 24 sq.ft
Instructions: 107574
Please contact customer service directly at the E-mail or phone number listed below for any
quality issues. ONCE USED THIS PRODUCT CANNOT BE RETURNED TO STORE.
** Warranty cannot be honored without an original, dated receipt **
IMPORTANT-PLEASE READ:
This product is warranted to the original retail purchaser (from an authorized dealer) and is non-transferable.
Clam Outdoors has a three-year manufacturer's defect warranty from the date of original purchase. Warranty
does not cover cracked or worn bases (if runner kits have not been installed as recommended), cracked
windows, tent tears or cuts, or broken or bent hoops due to high wind weather conditions or unattended use.
Defective parts will be replaced or repaired (at the manufacturer's option) if found to be defective within three
years from the date of original purchase. Warranty will be void if product has been subject to neglect, misuse,
improper installation, misapplication, alteration, accident including but not limited to improper maintenance, or
use of unauthorized parts or attachments. Please read the entire owner's manual to ensure proper installation,
use, storage and care of your Clam Shelter.
To submit a warranty claim request, please use one of the following methods:
https://clamoutdoors.com/pages/warranty-form
Email:
customerservice@clamcorp.com
In your request, please include your full name, address, phone number, a copy of your receipt, a brief description
of the problem, and pictures to clearly show the area(s) of concern. Our Warranty Department will review your
request, and a Clam representative will contact you regarding your claim status. All returns must be shipped to
us postage pre-prepaid.
It is expressly understood that Clam Outdoors Inc., liability for its products, whether due to breach of
warranty, negligence, strict liability, or otherwise, is limited to the repair of the product as stated above. Clam is
not liable for any injury, loss, damage, or expense, whether direct or consequential, including but not limited to loss
of use, income, profit, or damage to material arising in connection with the sale, installation, use of, inability to
use, or the repair or replacement of Clam products. Clam reserves the right to make alterations or
modifications in its products at any time, which in its opinion, may improve the performance and efficiency of
the product. Clam shall not be obligated to make such alterations or modifications to products already in service
Clam contact information
Customer Service Hrs: 9am to 4pm, Monday – Friday Central Standard Time
Clam Outdoors
Attn: Customer Service
12135 Brockton Lane
Rogers, MN 55369
Phone: 763-231-4120
FISH TRAP BUILD VIDEO
CLAMOUTDOORS.COM
WARRANTY INFORMATION
** REGISTER YOUR PURCHASE ONLINE AT CLAMOUTDOORS.COM **
LIMITATION OF LIABILITY
RANGER XT
THERMAL
MODEL 18593

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ICE-OPS FOLDS of HONOR RANGER XT THERMAL and is the answer not in the manual?

Questions and answers

Summary of Contents for Clam ICE-OPS FOLDS of HONOR RANGER XT THERMAL

  • Page 1 It is expressly understood that Clam Outdoors Inc., liability for its products, whether due to breach of warranty, negligence, strict liability, or otherwise, is limited to the repair of the product as stated above. Clam is not liable for any injury, loss, damage, or expense, whether direct or consequential, including but not limited to loss of use, income, profit, or damage to material arising in connection with the sale, installation, use of, inability to use, or the repair or replacement of Clam products.
  • Page 2: Parts List

    PARTS LIST QTY. PART NO. DESCRIPTION 107573 BASE, RANGER 107470 EXTENSION HOOP POLE, RANGER XT (GREEN ZIP TIE) 107469 HOOP POLE, RANGER XT 107460 HALF HOOP POLE, RANGER XT 114271 LARGE DIMMABLE LIGHT STICK 107471 TENT, RANGER XT THERMAL 108829 BATTERY BRACKET/HARDWARE 107351 SEAT COVER BACK...
  • Page 3 HARDWARE FASTENERS REFERENCE...
  • Page 4: Step 1 - Seat Assembly

    STEP 1 – SEAT ASSEMBLY Parts Needed for Step 1 Part Number Description Quantity 106003 CHAIR LEG BASE 106004 CHAIR LEG 102759 DELUXE SEAT 105478 SEAT SWIVEL 107351 SEAT COVER BACK 107352 SEAT COVER BOTTOM 101470 SCREW, 1/4-20 X 0.50 106456 SCREW, 1/ 4-20 X 1.75 101081...
  • Page 5 E. Flip the Deluxe Seat #102759 upside down and attach the swivel assembly to the bottom of the seat using #101470 bolts and tighten with a 3/8” wrench or socket. F. Insert Seat Cover Back #107351 and Bottom #107352 onto completed seat assembly, starting with the bottom cushion, and secure Velcro.
  • Page 6 STEP 2 – LIGHT STICK HOOP ASSEMBLY Parts Needed for Step 2 Part Number Description Quantity 107460 HALF HOOP POLE 114271 LARGE LIGHT STICK 106410 LIGHT CORD STORAGE BAG A. Install Light Stick #114271 into the #107460 Half Hoop Poles to make the light stick hoop assembly.
  • Page 7 STEP 3 – EXTENSION HOOP POLE ASSEMBLY DO NOT CUT ANY OF YOUR POLES NOTE: The Extension Hoop Pole #107470 is identified with a green zip tie. This pole is also shorter in length than the other hoop poles included with the shelter. Parts Needed for Step 3 Part Number Description...
  • Page 8 TIP: Twist the lever on the RPSX Collars 90 degrees to allow for easier installation onto Hoop Pole. Align RPSX Collar with the holes in the Hoop Pole as shown Collar tab is placed on inside of tube D. Attach Extension Support Poles #106896 with the notch of the pole facing inward. Use hardware provided with the Extension Clamps to secure.
  • Page 9: Step 4 - Seat Brackets

    Extension Hoop Pole #107470 Light Stick Hoop Pole Assembly STEP 4 – SEAT BRACKETS Parts Needed for Step 4 Part Number Description Quantity 106007 SEAT BRACKET 105794 BOLT, 1/4-20 X .75 101081 WASHER, 1/4 FLAT 106284 NUT, 1/4-20, NYLOCK A. Line up Seat Bracket #106007 with predrilled holes on front lip of sled.
  • Page 10 STEP 5 – POLE MOUNTING BRACKETS Parts Needed for Step 5 Part Number Description Quantity 106800 MOUNTING BRACKET 106286 SCREW, 1/4-20 X 0.75 106284 NUT, 1/4-20, NYLOCK A. Line up Mounting Bracket #106800 with predrilled holes on end of sled. B.
  • Page 11 STEP 7 – CANOPY SUPPORT POLES NOTE: During installation, ensure that all Support Poles (#107498 and #103599) have slots facing inward. Parts Needed for Step 7 Part Number Description Quantity 107498 BENT PORCH SUPPORT POLE 103599 STRAIGHT CANOPY SUPPORT POLE 106331 SCREW, 1/4-20 X 2.50 106284...
  • Page 12 STEP 8 – HOOP POLES Parts Needed for Step 8 Part Number Description Quantity 107469 HOOP POLE 103605 LARGE RPSX COLLAR 101840 REAR SPREADER POLE EXTENSION HOOP POLE ASSEMBLY (From Step 3) A. Put RPSX Collars #103605 onto one Hoop Pole #107469. B.
  • Page 13 STEP 9 – PUTTING SEATS IN SHELTER A. Install seat assemblies into shelter as shown, noting the seat latch clip position. Chair needs to be in the lock position when sitting. It’s also important to have the seats in place for added weight to help with the tent installation process.
  • Page 14 A. Drape the tent over the Hoop Poles. Attach the tent to the poles on the inside with the Velcro straps. B. Slide the remaining front Hoop Pole through the sleeve in the front of the tent. Slide remaining Connect Hoop Hoop Pole Pole to Bent Porch through sleeve in...
  • Page 15: Tips For Use

    NOTE: Pulling behind an ATV or snowmobile may result in premature wear of the base. ▪ In windy conditions it is advised to secure your shelter to the ice using Clam’s Ice Anchor Kit (part # 108064) and Ice Anchor Installation Tool (part #108348).
  • Page 16: Safety Instructions

    Q: What is the proper way to set up and take down my Fish Trap? Set-Up:  Face the seats. Grab the floor hoop pole and pull on it until you feel and hear the RPSX collar pins engaging in the fully open position. Grab the next hoop and do the same until all the hoops are fully open.
  • Page 17: Frequently Ask Questions

    FREQUENTLY ASK QUESTIONS Fish Trap FAQ’s Q: Should I install a runner kit/hyfax to the base of my shelter? A: The warranty on our shelters does not cover cracked or worn bases if a runner kit has not been installed. Additionally, bases will wear much quicker without a runner kit installed. Q: The zipper on my shelter freezes up and/or sticks.
  • Page 18 begin to flake off, especially along the folds in the fabric when the shelter is collapsed. This does not affect the function of the fabric. If you feel that too much light is now entering your shelter in the places where some of the coating has come off, you may wish to apply a new layer of rubberized coating.

This manual is also suitable for:

18593

Table of Contents