Related Manuals for Wenglor PEBL 01 Series
Summary of Contents for Wenglor PEBL 01 Series
- Page 1 PEBLx01 Light Curtains Pick-to-Light Operating Instructions Translation of the original operating instructions Subject to change without notice Available as PDF file only Version 1.0.0 As of: 08/21/2023 www.wenglor.com...
-
Page 2: Table Of Contents
Table of Contents 1. General ............................3 1.1 Information Concerning these Instructions .....................3 1.2 Explanations of Symbols ........................3 1.3 Limitation of Liability ..........................4 1.4 Copyrights ...............................4 2. For Your Safety ........................5 2.1 Use for Intended Purpose ........................5 2.2 Use for Other than the Intended Purpose ....................5 2.3 Personnel Qualifications .........................6 2.4 Modification of Products .........................6 2.5 General Safety Precautions ........................6... -
Page 3: General
• The product is subject to further technical development, and thus the information contained in these operat- ing instructions may also be subject to change. The current version can be found at www.wenglor.com in the product’s separate download area. NOTE! The operating instructions must be read carefully before using the product and must be kept on hand for later reference. -
Page 4: Limitation Of Liability
• wenglor assumes no liability for printing errors or other inaccuracies contained in these operating instruc- tions unless wenglor was verifiably aware of such errors at the point in time at which the operating instruc- tions were prepared. -
Page 5: For Your Safety
• The product is not suitable for use in potentially explosive atmospheres. • The product may be used only with accessories supplied or approved by wenglor, or in combination with approved products. A list of approved accessories and combination products can be found at www.wenglor. -
Page 6: Personnel Qualifications
• In the event of possible changes, the respectively current version of the operating instruc- tions can be accessed at www.wenglor.com in the product’s separate download area. • Read the operating instructions carefully before using the product. -
Page 7: Technical Data
3. Technical Data 3.1 Technical Data Order number PEBL101 PEBL201 PEBL301 Optical Data Range 2,000 mm Minimum distance to reflector 100 mm Measuring field height (MFH) 120 mm 270 mm 420 mm Beam distance 30 mm Switching hysteresis < 15% Light source Red light Polarization Filters... -
Page 8: Housing Dimensions
3.2 Housing Dimensions Dimensions specified in mm (1 = 0.03937 inch) 1 = Emitter diode 2 = Receiver diode 3 = Job indication Technical Data... -
Page 9: Connection Diagram
3.3 Connection Diagram Symbolerklärung Encoder A/A (TTL) Platin-Messwiderstand Encoder B/B (TTL) Versorgungsspannung + nicht angeschlossen Encoder A Versorgungsspannung 0 V Testeingang Versorgungsspannung (Wechselspannung) Encoder B Testeingang invertiert Schaltausgang Schließer (NO) Digitalausgang MIN Triggereingang Schaltausgang Öffner (NC) Digitalausgang MAX Bezugsmasse/Triggereingang Verschmutzungs-/Fehlerausgang (NO) Digitalausgang OK Analogausgang... -
Page 10: Complementary Products
3.4 Complementary Products wenglor can provide you with suitable connection equipment for your product. Suitable connection equipment no. Reflector foil ZRDF10K01 Reflector ZRDE12B01 (PEBL101) Reflector ZRDE12B02 (PEBL201) Reflector ZRDE12B03 (PEBL301) PNP-NPN converter BG2V1P-N-2M 3.5 Control Panel 01 = switching status indicator... -
Page 11: Transport And Storage
4. Transport and Storage 4.1 Transport Upon receipt of shipment, the goods must be inspected for damage in transit. In the case of damage, con- ditionally accept the package and notify the manufacturer of the damage. Then return the device, making reference to damage in transit. -
Page 12: Installation
5. Installation The light barrier is mounted with the help of the through-holes. The hole spacings can be found in the draw- ings below. Install the sensor(s) in a row and align them with the reflector on the back of the following sensor. Install a suitable reflector (see supplementary products) at the end of the row and align the last Sensor to it. - Page 13 Mounting on Profiles M4 screws must be used for mounting on profiles. The screws are fed through the holes in the Light Curtain and tightened into corresponding M4 slot nuts in the profile. a = screw M4 b = slot nut c = washer •...
-
Page 14: Functions Overview
6. Functions Overview 6.1 Default Settings Technical Data Order number Switching output Normally Open (NO) Job indication Blinks 6.2 Function Definitions If supply power is applied to the input, the green job indication is activated. The output is switched as soon as an object (e.g. -
Page 15: Settings
• If the teach-in key is not pressed for 15 seconds, the sensor exits the setting mode automatically. 8. Maintenance Instructions NOTE! • This wenglor sensor is maintenance-free. • Cleaning and inspection of the plug connections at regular intervals are advisable. • Do not clean the sensor with solvents or cleaning agents that could damage the product. -
Page 16: Proper Disposal
9. Proper Disposal wenglor sensoric GmbH does not accept the return of unusable or irreparable products. Respectively valid national waste disposal regulations apply to product disposal. 10. Appendix 10.1 List of Abbreviations Abbreviation Meaning Measuring field height Housing length Reflector length 10.2 Change Index for Operating Instructions... - Page 17 Photoelectronic Sensors...
Need help?
Do you have a question about the PEBL 01 Series and is the answer not in the manual?
Questions and answers