Related Manuals for Beijer Electronics GL-9031
Summary of Contents for Beijer Electronics GL-9031
- Page 1 User Manual GL-9031 Network Adapter Module CC-Link network adapter, light version, max. 12 slices Doc ID: 172909 2025-02-20...
- Page 2 The information in this document is subject to change without notice and is provided as available at the time of printing. Beijer Electronics AB reserves the right to change any information without updating this publication. Beijer Electronics AB assumes no responsibility for any errors that may appear in this document.
-
Page 3: Table Of Contents
10.3. RWr / RWw Area ................21 10.4. System Area ..................22 10.5. Reaction on Network Error ..............22 10.6. Service Message ................23 10.7. Service Message Request ..............23 10.8. Service Message Response ..............24 Beijer Electronics, Doc ID: 172909 2025-02... -
Page 5: About This Manual
About This Manual 1. About This Manual This manual contains information on the software and hardware features of the Beijer Electronics GL-9031 Network Adapter Module. It provides in-depth specifications, guidance on installation, setup, and usage of the product. 1.1. Symbols Used in This Manual This publication includes Warning, Caution, Note and Important icons where appropriate, to point out safety-related, or other important information. -
Page 6: Safety
Before using this product, please read this manual and other relevant manuals carefully. Pay full attention to safety instructions! In no event will Beijer Electronics be responsible or liable for damages resulting from the use of this product. The images, examples and diagrams in this manual are included for illustrative purposes. Because of the many variables and requirements associated with any particular installation, Beijer Electronics cannot take responsibility or liability for actual use based on the examples and diagrams. -
Page 7: About The G-Series System
IP, EtherCAT, PROFINET, CC-Link IE Field, PROFIBUS, CANopen, DeviceNet, CC-Link, MODBUS/Serial etc. • Expansion Module - Expansion module types: Digital IO, Analog IO, and Special modules. • Messaging - The system uses two types of messaging: Service messaging and IO messaging. Beijer Electronics, Doc ID: 172909 2025-02... -
Page 8: Io Process Data Mapping
Valid parameter data depends on the modules in use. For example, analog modules have settings of either 0-20 mA or 4-20 mA, and temperature modules have settings such as PT100, PT200, and PT500. The documentation for each module provides a description of the parameter data. 2025-02 Beijer Electronics, Doc ID: 172909... -
Page 9: Specifications
IO cable max. 2.0 mm (AWG 14) Weight 71 g Dimensions 22 mm x 109 mm x 70 mm 4.3. Communication Interface Specification Adapter type Slave node (CC-Link Version 1) Max. expansion slot 12 slots Beijer Electronics, Doc ID: 172909 2025-02... - Page 10 Module status (MOD) - Green/Red Current running status (NET) - Green Error status (ERR) - Green Expansion module status (IOS) - Green/Red Module location Starter module left side of G-series system Station class Remote device station 2025-02 Beijer Electronics, Doc ID: 172909...
-
Page 11: Wiring Diagram
5. Wiring Diagram Pin no. Signal description System power, 24 V System power, ground Frame ground Field power, ground Field power, 24 V WARNING Never connect system power to field power! Use separate power supplies. Beijer Electronics, Doc ID: 172909 2025-02... -
Page 12: Led Indicator
Exceeded number range of device station. 6.4. IOS (Expansion Module Status) Status Indicates Not powered, no Device has no expansion module or is not powered. expansion module No expansion module Flashing Adapter has no expansion module. 2025-02 Beijer Electronics, Doc ID: 172909... - Page 13 • Detect invalid expansion module ID. • Overflowed input/output size. • Too many expansion modules. • Initialization failure. • Communication error. • Changed expansion module configuration. • Mismatch vendor code between adapter and expansion module. Beijer Electronics, Doc ID: 172909 2025-02...
-
Page 14: Pin Open Connector
5-Pin Open Connector 7. 5-Pin Open Connector Connector no. Signal name Description DATA+ Transceiver data high DATA- Transceiver data low Signal common Shield Shield Frame Ground. Internally shorted with shield. 2025-02 Beijer Electronics, Doc ID: 172909... -
Page 15: Dip Switches
Default baud rate: 156 Kbps Node address pole setting examples ID = 0 ID = 1 ID = 10 ID = 42 ID = 64 8.2. 4 Pole Switch Pole# Description Fixed station OFF: Auto addressable. ON: 4station occupied. Beijer Electronics, Doc ID: 172909 2025-02... -
Page 16: Pole Switch
Mode switch is ON, the IO size will be increased 2 bytes more respectively. STOP action OFF: Master value dependent. ON: Output clear. Reserved 8.3. 2 Pole Switch Pole# Description Terminator resistor 1 ON, 2 ON: Terminator resistor set. Other: Terminator resistor not set. 2025-02 Beijer Electronics, Doc ID: 172909... -
Page 17: Hardware Setup
Installation position is valid vertical and horizontal. The drawings are illustrative and may be out of proportion. CAUTION NOT following the space requirements may result in damaging the product. Beijer Electronics, Doc ID: 172909 2025-02... -
Page 18: Mount Module To Din Rail
• GT-5XXX • GT-7XXX GN-9XXX modules have three locking levers, one at the bottom and two on the side. For mounting instructions, refer to Mount GN-9XXX Module. Mount to DIN rail Dismount from DIN rail 2025-02 Beijer Electronics, Doc ID: 172909... - Page 19 9.2.2. Mount GN-9XXX Module To mount or dismount a network adapter or programmable IO module with the product name GN-9XXX, for example GN-9251 or GN-9371, see the following instructions: Mount to DIN rail Dismount from DIN rail Beijer Electronics, Doc ID: 172909 2025-02...
-
Page 20: Field Power And Data Pins
Token output port of processor module Serial output Transmitter output port of processor module Serial input Receiver input port of processor module Reserved Reserved for bypass token Field GND Field ground Field VCC Field supply voltage (24 VDC) 2025-02 Beijer Electronics, Doc ID: 172909... -
Page 21: Process Image
RWr4 - RWr7 2 stations 8 words RWr8 - RWr11 3 stations 12 words RWr12 - RWr27 4 stations 16 words Analog out / Special module Address Configuration Size RWw0 - RWw3 1 station 4 words Beijer Electronics, Doc ID: 172909 2025-02... -
Page 22: System Area
Error status flag Reserved Remote station ready Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved 10.5. Reaction on Network Error Description Hold last value Clear output to zero Stop bus Not used (internally switched to 10) 2025-02 Beijer Electronics, Doc ID: 172909... -
Page 23: Service Message
User data 17 User data 16 RWw[12] User data 19 User data 18 RWw[13] User data 21 User data 20 RWw[14] User data 23 User data 22 RWw[15] User data 25 User data 24 Beijer Electronics, Doc ID: 172909 2025-02... -
Page 24: Service Message Response
User data 17 User data 16 RWw[12] User data 19 User data 18 RWw[13] User data 21 User data 20 RWw[14] User data 23 User data 22 RWw[15] User data 25 User data 24 2025-02 Beijer Electronics, Doc ID: 172909...
Need help?
Do you have a question about the GL-9031 and is the answer not in the manual?
Questions and answers