Page 1 Wireless Bridge Device Information...
Page 2: Table Of Contents
Contents Chapter 1 About This Manual ..................... 1 Chapter 2 Elevator Series ......................3 2.1 2.4 GHz 200m ......................... 4 2.1.1 DS-3WF0BC-2NT ......................4 2.1.2 DS-3WF0BC-2NT(B) ..................... 11 2.2 2.4GHz 500m ........................18 2.2.1 DS-3WF0EC-2NT ......................18 2.3 5GHz 500m .......................... 25 2.3.1 DS-3WF0EC-5ACT ......................
Page 3 Wireless Bridge Device Information 3.5.2 DS-3WF02C-5AC/O ....................121 3.5.3 DS-3WF02C-5AC/O V2 ....................129 3.5.4 DS-3WF02C-5AC/O V3 ....................137 3.6 5GHz 15 km ........................145 3.6.1 DS-3WF03C-5AC/O ....................145 3.6.2 DS-3WF03C-5AC/O V2 ....................153 3.6.3 DS-3WF03C-5AC/O V3 ....................161 Chapter 4 First-Time Use ......................170 4.1 Activation ...........................
Page 4: Chapter 1 About This Manual
Wireless Bridge Device Information Chapter 1 About This Manual This manual collects device information for all models of Hikvision wireless bridges, including packing list, device appearance, device installation, device connection, activation, paring and remote management. Install Devices Get the detailed installation guide of the device model.
Page 5: Manage Devices
Wireless Bridge Device Information Note The device information varies with different models. The Quick Start Guide in the packaging is for reference only. First-Time Use For the first-time using, please complete the following steps: 1. Activation 2. Login 3. Device Pairing Manage Devices After the device is activated and paired, you can manage the device remotely.
Page 6: Chapter 2 Elevator Series
Wireless Bridge Device Information Chapter 2 Elevator Series This series of devices are suitable for wireless video transmission in elevators. Figure 2-1 Application Scene...
Page 7: Ghz 200M
Wireless Bridge Device Information 2.1 2.4 GHz 200m 2.1.1 DS-3WF0BC-2NT The 2.4 GHz wireless bridge (hereinafter referred to as the device) is used for wireless transmission within 200 m and is suitable for wireless video transmission in elevators . Packing List Please check if there is any damage of the package first.
Page 8 Wireless Bridge Device Information Item Appearance Quantity Quick Start Guide × 1 Regulatory Compliance and × 1 Safety Information Note The device image used here is only for example purpose. The actual device may vary with models. Interface/Button Figure 2-2 Device Interface/Button...
Page 9 Wireless Bridge Device Information Table 2-2 Device Interface/Button Description Interface/ B utton Description PoE/LAN 1 The 10/100 Mbps adaptive RJ45 port, also can be used as a PoE port. LAN 2 The 10/100 Mbps adaptive RJ45 port. Reset Long press for 4 seconds to restore to factory settings.
Page 10: Application Scene
Wireless Bridge Device Information Indicator Description Power Indicator Solid Green The device is powered on normally Unlit No power supply connected or power supply is abnormal. Application Scene Note The following application scenes are for your reference only. The actual scene prevails. ●...
Page 11: Preparation For Installation
Wireless Bridge Device Information Figure 2-4 Application Scene Preparation for Installation To avoid device damage or personal injury caused by improper usage of the device, please follow the preparations below. Use the attached power adapter and PoE injector to power the device. ●...
Page 12: Pole Installation
Wireless Bridge Device Information Disconnect the power supply when you have the device serviced. ● The temperature of the cover area will be high when the device is working. In the circumstances, ● only personnel with relevant professional knowledge, such as installation and maintenance personnel, are allowed to operate the device.
Page 13: Device Connection
Wireless Bridge Device Information Figure 2-6 Fix Device Note Adjust the direction of the device manually to keep the device installed horizontally. Device Connection Based on the actual situations, connect the device according to the following wiring steps. Note Use the attached the power adapter and PoE injector to power on the device. ●...
Page 14: Ds-3Wf0Bc-2Nt(B)
3. After you finish the device connection, check device working status, network connection, and signal strength according to indicators. 2.1.2 DS-3WF0BC-2NT(B) The 2.4 GHz wireless bridge (hereinafter referred to as the device) is used for wireless transmission within 200 m and is suitable for wireless video transmission in elevators .
Page 15 Wireless Bridge Device Information Table 2-4 Packing List Item Appearance Quantity Wireless Bridge × 2 PoE Injector × 2 Power Adapter × 2 Cable Tie × 4 Quick Start Guide × 1 Regulatory Compliance and × 1 Safety Information...
Page 16 Wireless Bridge Device Information Note The device image used here is only for example purpose. The actual device may vary with models. Interface/Button Figure 2-9 Device Interface/Button Table 2-5 Device Interface/Button Description Interface/ B utton Description Reset Long press for 4 seconds to restore to factory settings.
Page 17 Wireless Bridge Device Information Table 2-6 Device Indicator Description Indicator Description Signal Strength Solid on The devices are matched. Indicator Solid red, yellow, and green: The wireless signal is ● strong. Solid red and yellow, unlit green: The wireless ● signal is normal.
Page 18 Wireless Bridge Device Information Figure 2-11 Application Scene Preparation for Installation To avoid device damage or personal injury caused by improper usage of the device, please follow the preparations below. Use the attached power adapter and PoE injector to power the device. ●...
Page 19 Wireless Bridge Device Information Disconnect the power supply when you have the device serviced. ● The temperature of the cover area will be high when the device is working. In the circumstances, ● only personnel with relevant professional knowledge, such as installation and maintenance personnel, are allowed to operate the device.
Page 20 Wireless Bridge Device Information Figure 2-15 Fix Device Note Adjust the direction of the device manually to keep the device installed horizontally. Device Connection Based on the actual situations, connect the device according to the following wiring steps. Note Use the attached the power adapter and PoE injector to power on the device. ●...
Page 21: Ghz 500M
Wireless Bridge Device Information Figure 2-16 AP Connection 2. CPE connection: Figure 2-17 CPE Connection 3. After you finish the device connection, check device working status, network connection, and signal strength according to indicators. 2.2 2.4GHz 500m 2.2.1 DS-3WF0EC-2NT The 2.4 GHz wireless bridge (hereinafter referred to as the device) is used for wireless transmission within 500 m and is suitable for wireless video transmission in elevators .
Page 22 Wireless Bridge Device Information Packing List Please check if there is any damage of the package first. According to the packing list, make sure no item is lost. After checking all the items included, you can continue to install the device. Table 2-7 Packing List Item Appearance...
Page 23 Wireless Bridge Device Information Note The device image used here is only for example purpose. The actual device may vary with models. Interface/Button Figure 2-18 Device Interface/Button Table 2-8 Device Interface/Button Description Interface/ B utton Description PoE/LAN 1 The 10/100 Mbps adaptive RJ45 port, also can be used as a PoE port.
Page 24 Wireless Bridge Device Information Indicator Figure 2-19 Device Indicator Table 2-9 Device Indicator Description Indicator Description Signal Strength Solid on The devices are matched. Indicator Solid red, yellow, and green: The wireless signal is ● strong. Solid red and yellow, unlit green: The wireless ●...
Page 25 Wireless Bridge Device Information Figure 2-20 Application Scene Preparation for Installation To avoid device damage or personal injury caused by improper usage of the device, please follow the preparations below. Use the attached power adapter and PoE injector to power the device. ●...
Page 26 Wireless Bridge Device Information Disconnect the power supply when you have the device serviced. ● The temperature of the cover area will be high when the device is working. In the circumstances, ● only personnel with relevant professional knowledge, such as installation and maintenance personnel, are allowed to operate the device.
Page 27 Wireless Bridge Device Information Figure 2-22 Fix Device Note Adjust the direction of the device manually to keep the device installed horizontally. Device Connection Based on the actual situations, connect the device according to the following wiring steps. Note Use the attached the power adapter and PoE injector to power on the device. ●...
Page 28: 5Ghz 500M
Wireless Bridge Device Information Figure 2-23 AP Connection 2. CPE connection: Figure 2-24 CPE Connection 3. After you finish the device connection, check device working status, network connection, and signal strength according to indicators. 2.3 5GHz 500m 2.3.1 DS-3WF0EC-5ACT The 5 GHz wireless bridge (hereinafter referred to as the device) is used for wireless transmission within 500 m and is suitable for wireless video transmission in elevators .
Page 29 Wireless Bridge Device Information Packing List Please check if there is any damage of the package first. According to the packing list, make sure no item is lost. After checking all the items included, you can continue to install the device. Table 2-10 Packing List Item Appearance...
Page 30 Wireless Bridge Device Information Note The device image used here is only for example purpose. The actual device may vary with models. Interface/Button Figure 2-25 AP Device Interface/Button Figure 2-26 CPE Device Interface/Button Table 2-11 Device Interface/Button Description Interface/ B utton Description Reset Long press for 4 seconds to restore to factory...
Page 31 Wireless Bridge Device Information Indicator Figure 2-27 Device Indicator Table 2-12 Device Indicator Description Indicator Description Signal Strength Solid on The devices are matched. Indicator Solid red, yellow, and green: The wireless signal is ● strong. Solid red and yellow, unlit green: The wireless ●...
Page 32 Wireless Bridge Device Information Application Scene Note The following application scenes are for your reference only. The actual scene prevails. ● The device image used here is only for example purpose. The actual device may vary with ● models. Figure 2-28 Application Scene...
Page 33 Wireless Bridge Device Information Preparation for Installation To avoid device damage or personal injury caused by improper usage of the device, please follow the preparations below. Use the attached power adapter and PoE injector to power the device. ● The distance between AP and CPE should be less than 500 m to secure transmission rate. ●...
Page 34 Wireless Bridge Device Information Figure 2-30 Fix Device Note Adjust the direction of the device manually to keep the device installed horizontally. Device Connection Based on the actual situations, connect the device according to the following wiring steps. Note Use the attached the power adapter and PoE injector to power on the device. ●...
Page 35 Wireless Bridge Device Information Figure 2-31 AP Connection (Wireless Bridge Mode) Figure 2-32 AP Connection (Routing Mode) 2. CPE connection:...
Page 36: Ds-3Wf0Ec-5Act(B)
Wireless Bridge Device Information Figure 2-33 CPE Connection 3. After you finish the device connection, check device working status, network connection, and signal strength according to indicators. 2.3.2 DS-3WF0EC-5ACT(B) The 5 GHz wireless bridge (hereinafter referred to as the device) is used for wireless transmission within 500 m and is suitable for wireless video transmission in elevators .
Page 37 Wireless Bridge Device Information Table 2-13 Packing List Item Appearance Quantity Wireless Bridge × 2 PoE Power Supply × 2 AC Cord (Connect to the PoE × 2 Power Supply) Cable Tie × 4...
Page 38 Wireless Bridge Device Information Item Appearance Quantity Quick Start Guide × 1 Regulatory Compliance and × 1 Safety Information Note The device image used here is only for example purpose. The actual device may vary with models. Interface/Button Figure 2-34 AP Device Interface/Button...
Page 39 Wireless Bridge Device Information Figure 2-35 CPE Device Interface/Button Table 2-14 Device Interface/Button Description Interface/ B utton Description Standard PoE IN/LAN 1 The 10/100 Mbps adaptive RJ45 port, also can be used as a standard PoE input port. LAN 2 The 10/100 Mbps adaptive RJ45 port.
Page 40 Wireless Bridge Device Information Table 2-15 Device Indicator Description Indicator Description Signal Strength Solid on The devices are matched. Indicator Solid red, yellow, and green: The wireless signal is ● strong. Solid red and yellow, unlit green: The wireless ● signal is normal.
Page 41 Wireless Bridge Device Information Figure 2-37 Application Scene Preparation for Installation To avoid device damage or personal injury caused by improper usage of the device, please follow the preparations below. Use the attached PoE power supply to power the device. ●...
Page 42 Wireless Bridge Device Information Disconnect the power supply when you have the device serviced. ● The temperature of the cover area will be high when the device is working. In the circumstances, ● only personnel with relevant professional knowledge, such as installation and maintenance personnel, are allowed to operate the device.
Page 43 Wireless Bridge Device Information Figure 2-39 Fix Device Note Adjust the direction of the device manually to keep the device installed horizontall. Device Connection Based on the actual situations, connect the device according to the following wiring steps. Note Use the attached PoE power supply to power on the device. ●...
Page 44 Wireless Bridge Device Information Figure 2-40 AP Connection (With PoE Power Supply) Figure 2-41 AP Connection (With PoE Switch) 2. CPE connection:...
Page 45 Wireless Bridge Device Information Figure 2-42 CPE Connection 3. After you finish the device connection, check device working status, network connection, and signal strength according to indicators.
Page 46: Chapter 3 Outdoor Series
Wireless Bridge Device Information Chapter 3 Outdoor Series This series of devices are suitable for outdoor video transmission. Figure 3-1 Application Scene 3.1 2.4GHz 500m 3.1.1 DS-3WF500-EI-2N The 2.4 GHz wireless bridge (hereinafter referred to as the device) is used for wireless transmission within 500 m.
Page 47 Wireless Bridge Device Information Table 3-1 Packing List Item Appearance Quantity Wireless Bridge × 2 PoE Injector × 2 Power Adapter × 2 Cable Tie × 4 Quick Start Guide × 1 Regulatory Compliance and × 1 Safety Information...
Page 48 Wireless Bridge Device Information Note The device image used here is only for example purpose. The actual device may vary with models. Interface/Button Figure 3-2 Device Interface/Button Table 3-2 Device Interface/Button Description Interface/ B utton Description Reset Long press for 4 seconds to restore to factory settings.
Page 49 Wireless Bridge Device Information Indicator Figure 3-3 Device Indicator Table 3-3 Device Indicator Description Indicator Description Signal Strength Solid on The devices are matched. Indicator Solid red, yellow, and green: The wireless signal is ● strong. Solid red and yellow, unlit green: The wireless ●...
Page 50 Wireless Bridge Device Information Application Scene Figure 3-4 Application Scene Preparation for Installation To avoid device damage or personal injury caused by improper usage of the device, please follow the preparations below. Use the attached power adapter and PoE injector to power the device. ●...
Page 51 Wireless Bridge Device Information Pole Installation Mount the device on the pole with a diameter of 40 to 100 mm using the attached cable tie. Please read and follow the steps: 1. Thread the cable ties into the installation holes at the back of the device. Figure 3-5 Thread Cable Ties 2.
Page 52 Wireless Bridge Device Information Figure 3-6 Fix Device Note Adjust the direction of the device manually to keep the device installed vertically. Device Connection Based on the actual situations, connect the device according to the following wiring steps. Note Use the attached power adapter and PoE injector to power on the device. ●...
Page 53: Ds-3Wf500S-Ei-2N
Wireless Bridge Device Information Figure 3-7 AP Connection 2. CPE connection: Figure 3-8 CPE Connection 3. After you finish the device connection, check device working status, network connection, and signal strength according to indicators. 3.1.2 DS-3WF500S-EI-2N The 2.4 GHz wireless bridge (hereinafter referred to as the device) is used for wireless transmission within 500 m.
Page 54 Wireless Bridge Device Information Packing List Please check if there is any damage of the package first. According to the packing list, make sure no item is lost. After checking all the items included, you can continue to install the device. Table 3-4 Packing List Item Appearance...
Page 55 Wireless Bridge Device Information Item Appearance Quantity Quick Start Guide × 1 Regulatory Compliance and × 1 Safety Information Note The device image used here is only for example purpose. The actual device may vary with models. Interface/Button Figure 3-9 Device Interface/Button...
Page 56 Wireless Bridge Device Information Table 3-5 Device Interface/Button Description Interface/ B utton Description Reset Long press for 4 seconds to restore to factory settings. PoE/LAN The 10/100 Mbps adaptive RJ45 port, also can be used as a PoE port. Network Cable Slot Reserved for easy placement of the network cables.
Page 57 Wireless Bridge Device Information Indicator Description Unlit The port is disconnected or connection is abnormal. Power Indicator Solid Green The device is powered on normally Unlit No power supply connected or power supply is abnormal. Application Scene Figure 3-11 Application Scene Preparation for Installation To avoid device damage or personal injury caused by improper usage of the device, please follow the preparations below.
Page 58 Wireless Bridge Device Information Make sure the water-proof cover is installed. ● Protect the power adapter and PoE injector from rain. It is suggested to put them into a ● waterproof case or keep them in a dry place. It is suggested to manage the gap between cover and device with fluid dispensing. ●...
Page 59 Wireless Bridge Device Information Figure 3-13 Fix Device Note Adjust the direction of the device manually to keep the device installed vertically. CPE Connection Note Use the attached power adapter and PoE injector to power on the device. ● The power adapter and PoE injector must be connected to an earthed socket outlet. ●...
Page 60: Ghz 1Km
Wireless Bridge Device Information Figure 3-14 CPE Connection After you finish the device connection, check device working status, network connection, and signal strength according to indicators. 3.2 2.4GHz 1km 3.2.1 DS-3WF0FA-2N/O The 2.4 GHz wireless bridge (hereinafter referred to as the device) is used for wireless transmission within 1 km.
Page 61 Wireless Bridge Device Information Table 3-7 Packing List Item Appearance Quantity Wireless Bridge × 1 PoE Injector × 1 Power Adapter × 1 Cable Tie × 4 Quick Start Guide × 1 Regulatory Compliance and × 1 Safety Information Note The device image used here is only for example purpose.
Page 62 Wireless Bridge Device Information Interface/Button Figure 3-15 Device Interface/Button Table 3-8 Device Interface/Button Description Interface/ B utton Description PoE/LAN 1 The 10/100 Mbps adaptive RJ45 port, also can be used as a PoE port. LAN 2 The 10/100 Mbps adaptive RJ45 port. Reset Long press for 4 seconds to restore to factory settings.
Page 63 Wireless Bridge Device Information Table 3-9 Device Indicator Description Indicator Description Signal Strength Solid on The devices are matched. Indicator Solid red, yellow, and green: The wireless signal is ● strong. Solid red and yellow, unlit green: The wireless ● signal is normal.
Page 64 Wireless Bridge Device Information Application Scene Figure 3-17 Application Scene Preparation for Installation To avoid device damage or personal injury caused by improper usage of the device, please follow the preparations below. Use the attached power adapter and PoE injector to power the device. ●...
Page 65 Wireless Bridge Device Information Pole Installation Mount the device on the pole with a diameter of 40 to 100 mm using the attached cable tie. Please read and follow the steps: 1. Thread the cable ties into the installation holes at the back of the device. Figure 3-18 Thread Cable Ties 2.
Page 66: Device Connection
Wireless Bridge Device Information Figure 3-19 Fix Device Note Adjust the direction of the device manually to keep the device installed vertically. Device Connection Based on the actual situations, connect the device according to the following wiring steps. Note Use the attached the power adapter and PoE injector to power on the device. ●...
Page 67: Ds-3Wf0Fc-2N/O
Wireless Bridge Device Information Figure 3-20 AP Connection 2. CPE connection: CPE device can supply power to IPC. Figure 3-21 CPE Connection 3. After you finish the device connection, check device working status, network connection, and signal strength according to indicators. 3.2.2 DS-3WF0FC-2N/O The 2.4 GHz wireless bridge (hereinafter referred to as the device) is used for wireless transmission within 1 km.
Page 68 Wireless Bridge Device Information Packing List Please check if there is any damage of the package first. According to the packing list, make sure no item is lost. After checking all the items included, you can continue to install the device. Table 3-10 Packing List Item Appearance...
Page 69 Wireless Bridge Device Information Item Appearance Quantity Quick Start Guide × 1 Regulatory Compliance and × 1 Safety Information Note The device image used here is only for example purpose. The actual device may vary with models. Interface/Button Figure 3-22 Device Interface/Button...
Page 70 Wireless Bridge Device Information Table 3-11 Device Interface/Button Description Interface/ B utton Description Reset Long press for 4 seconds to restore to factory settings. PoE IN/LAN 1 The 10/100 Mbps adaptive RJ45 port, also can be used as a PoE port. LAN 2 The 10/100 Mbps adaptive RJ45 port.
Page 71 Wireless Bridge Device Information Indicator Description Power Indicator Solid Green The device is powered on normally Unlit No power supply connected or power supply is abnormal. Application Scene Figure 3-24 Application Scene Preparation for Installation To avoid device damage or personal injury caused by improper usage of the device, please follow the preparations below.
Page 72 Wireless Bridge Device Information Protect the power adapter and PoE injector from rain. It is suggested to put them into a ● waterproof case or keep them in a dry place. It is suggested to manage the gap between cover and device with fluid dispensing. ●...
Page 73 Wireless Bridge Device Information Figure 3-26 Fix Device Note Adjust the direction of the device manually to keep the device installed vertically. Device Connection Based on the actual situations, connect the device according to the following wiring steps. Note Use the attached the power adapter and PoE injector to power on the device. ●...
Page 74: Ds-3Wf1000-Ei-2N
Wireless Bridge Device Information Figure 3-27 AP Connection 2. CPE connection: Figure 3-28 CPE Connection 3. After you finish the device connection, check device working status, network connection, and signal strength according to indicators. 3.2.3 DS-3WF1000-EI-2N The 2.4 GHz wireless bridge (hereinafter referred to as the device) is used for wireless transmission within 1 km.
Page 75 Wireless Bridge Device Information Packing List Please check if there is any damage of the package first. According to the packing list, make sure no item is lost. After checking all the items included, you can continue to install the device. Table 3-13 Packing List Item Appearance...
Page 76 Wireless Bridge Device Information Note The device image used here is only for example purpose. The actual device may vary with models. Interface/Button Figure 3-29 Device Interface/Button Table 3-14 Device Interface/Button Description Interface/ B utton Description Reset Long press for 4 seconds to restore to factory settings.
Page 77 Wireless Bridge Device Information Table 3-15 Device Indicator Description Indicator Description Signal Strength Solid on The devices are matched. Indicator Solid red, yellow, and green: The wireless signal is ● strong. Solid red and yellow, unlit green: The wireless ● signal is normal.
Page 78 Wireless Bridge Device Information Application Scene Figure 3-31 Application Scene Preparation for Installation To avoid device damage or personal injury caused by improper usage of the device, please follow the preparations below. Use the attached power adapter and PoE injector to power the device. ●...
Page 79 Wireless Bridge Device Information Pole Installation Mount the device on the pole with a diameter of 40 to 100 mm using the attached cable tie. Please read and follow the steps: 1. Thread the cable ties into the installation holes at the back of the device. Figure 3-32 Thread Cable Ties 2.
Page 80 Wireless Bridge Device Information Figure 3-33 Fix Device Note Adjust the direction of the device manually to keep the device installed vertically. Device Connection Based on the actual situations, connect the device according to the following wiring steps. Note Use the attached power adapter and PoE injector to power on the device. ●...
Page 81: Ds-3Wf1000S-Ei-2N
Wireless Bridge Device Information Figure 3-34 AP Connection 2. CPE connection: Figure 3-35 CPE Connection 3. After you finish the device connection, check device working status, network connection, and signal strength according to indicators. 3.2.4 DS-3WF1000S-EI-2N The 2.4 GHz wireless bridge (hereinafter referred to as the device) is used for wireless transmission within 1 km.
Page 82 Wireless Bridge Device Information Packing List Please check if there is any damage of the package first. According to the packing list, make sure no item is lost. After checking all the items included, you can continue to install the device. Table 3-16 Packing List Item Appearance...
Page 83 Wireless Bridge Device Information Note The device image used here is only for example purpose. The actual device may vary with models. Interface/Button Figure 3-36 Device Interface/Button Table 3-17 Device Interface/Button Description Interface/ B utton Description Reset Long press for 4 seconds to restore to factory settings.
Page 84 Wireless Bridge Device Information Table 3-18 Device Indicator Description Indicator Description Signal Strength Solid on The devices are matched. Indicator Solid red, yellow, and green: The wireless signal is ● strong. Solid red and yellow, unlit green: The wireless ● signal is normal.
Page 85 Wireless Bridge Device Information Application Scene Figure 3-38 Application Scene Preparation for Installation To avoid device damage or personal injury caused by improper usage of the device, please follow the preparations below. Use the attached power adapter and PoE injector to power the device. ●...
Page 86 Wireless Bridge Device Information Pole Installation Mount the device on the pole with a diameter of 40 to 100 mm using the attached cable tie. Please read and follow the steps: 1. Thread the cable ties into the installation holes at the back of the device. Figure 3-39 Thread Cable Ties 2.
Page 87 Wireless Bridge Device Information Figure 3-40 Fix Device Note Adjust the direction of the device manually to keep the device installed vertically. Device Connection Based on the actual situations, connect the device according to the following wiring steps. Note Use the attached power adapter and PoE injector to power on the device. ●...
Page 88: 5Ghz 1Km
Wireless Bridge Device Information Figure 3-41 CPE Connection After you finish the device connection, check device working status, network connection, and signal strength according to indicators. 3.3 5GHz 1km 3.3.1 DS-3WF0FA-5AC/O The 5 GHz wireless bridge (hereinafter referred to as the device) is used for wireless transmission within 1 km.
Page 89 Wireless Bridge Device Information Table 3-19 Packing List Item Appearance Quantity Wireless Bridge × 1 PoE Power Supply × 1 AC Cord (Connect to the PoE × 1 Power Supply) Antenna (with accessory bag) × 1 Cable Tie × 2...
Page 90 Wireless Bridge Device Information Item Appearance Quantity Quick Start Guide × 1 Regulatory Compliance and × 1 Safety Information Note The device image used here is only for example purpose. The actual device may vary with models. Interface/Button Figure 3-42 Device Interface/Button Table 3-20 Device Interface/Button Description Interface/...
Page 91 Wireless Bridge Device Information Interface/ B utton Description LAN 2 The 10/100/1000 Mbps adaptive RJ45 port. CPE/AP DIP Switch Switch up or down / left or right to set the device as AP or CPE. Reset Long press for 4 seconds to restore to factory settings.
Page 92 Wireless Bridge Device Information Indicator Figure 3-43 Device Indicator Table 3-22 Device Indicator Description Indicator Description Signal Strength Solid on The devices are matched. Indicator Solid red, yellow, and green: The wireless signal is ● strong. Solid red and yellow, unlit green: The wireless ●...
Page 93 Wireless Bridge Device Information Application Scene Figure 3-44 Application Scene...
Page 94 Wireless Bridge Device Information Preparation for Installation Figure 3-45 Installation Procedure To avoid device damage or personal injury caused by improper usage of the device, please follow the preparations below. Use the attached PoE power supply to power the device. ●...
Page 95: Antenna Installation
Wireless Bridge Device Information Antenna Installation By using the attached accessories, the antenna can be installed onto a mounting pole (user supplied) with a diameter of 30 to 70 mm. Steps: 1. Remove the nuts, spring washers, and flat washers from the bolts (× 4). 2.
Page 96: Antenna Connection
Wireless Bridge Device Information Note It is easy to take down the wall-mounted device. You are recommended to install the device onto a mounting pole. 1. Choose an appropriate installation site for the wireless bridge below the antenna on the pole. Note The vertical distance between the antenna and the wireless bridge should be within 100 mm.
Page 97 Wireless Bridge Device Information Figure 3-48 Connect Antenna Device Connection Based on the actual situations, connect the device according to the following wiring steps. Note The device can be powered on in various ways, you can use the attached PoE power adapter or ●...
Page 98 Wireless Bridge Device Information Figure 3-49 AP Connection (With PoE Power Supply) Figure 3-50 AP Connection (With PoE Switch) 2. CPE connection: a. Switch the CPE/AP DIP to set the device as CPE. b. Select the SSID No. set on the AP to match (Select SSID NO. 1 for example). c.
Page 99 Wireless Bridge Device Information Figure 3-51 CPE Connection (with PoE Power Supply) Figure 3-52 CPE Connection (with PoE Switch) d. Optional: If there are more than one CPE (no more than 4) to be matched with one AP, repeat the previous steps connect and set the CPEs. 3.
Page 100: 5Ghz 3Km
Wireless Bridge Device Information 3.4 5GHz 3km 3.4.1 DS-3WF3000-EI-5AC/P The 5 GHz wireless bridge (hereinafter referred to as the device) is used for wireless transmission within 3 km. It supports point-to-point transmission and can guarantee the multi-channel HD video transmission for outdoor video security. Packing List Please check if there is any damage of the package first.
Page 101 Wireless Bridge Device Information Item Appearance Quantity Cable Tie × 4 Quick Start Guide × 1 Regulatory Compliance and × 1 Safety Information Note The device image used here is only for example purpose. The actual device may vary with models. Interface/Button Figure 3-53 AP Device Interface/Button...
Page 102 Wireless Bridge Device Information Figure 3-54 CPE Device Interface/Button Table 3-24 Device Interface/Button Description Interface/ B utton Description Standard PoE IN/LAN 1 The 10/100 Mbps adaptive RJ45 port, also can be used as a standard PoE input port. LAN 2 The 10/100 Mbps adaptive RJ45 port.
Page 103 Wireless Bridge Device Information Indicator Figure 3-55 Device Indicator Table 3-25 Device Indicator Description Indicator Description Signal Strength Solid on The devices are matched. Indicator Solid red, yellow, and green: The wireless signal is ● strong. Solid red and yellow, unlit green: The wireless ●...
Page 104 Wireless Bridge Device Information Application Scene Figure 3-56 Application Scene Preparation for Installation To avoid device damage or personal injury caused by improper usage of the device, please follow the preparations below. Use the attached PoE power supply to power the device. ●...
Page 105: Pole Installation
Wireless Bridge Device Information Pole Installation Mount the device on the pole with a diameter of 40 to 100 mm using the attached cable tie. Please read and follow the steps: 1. Thread the cable ties into the installation holes at the back of the device. Figure 3-57 Thread Cable Ties 2.
Page 106 Wireless Bridge Device Information Figure 3-58 Fix Device Note Adjust the direction of the device manually to keep the device installed vertically. Device Connection Based on the actual situations, connect the device according to the following wiring steps. Note Use the attached PoE power supply and AC cord to power on the device. ●...
Page 107 Wireless Bridge Device Information Figure 3-59 AP Connection (With PoE Power Supply) Figure 3-60 AP Connection (With PoE Switch) 2. CPE connection: CPE device can supply power to IPC.
Page 108: Ds-3Wf3000S-Ei-5Ac/P
Wireless Bridge Device Information Figure 3-61 CPE Connection 3. After you finish the device connection, check device working status, network connection, and signal strength according to indicators. 3.4.2 DS-3WF3000S-EI-5AC/P The 5 GHz wireless bridge (hereinafter referred to as the device) is used for wireless transmission within 3 km.
Page 109 Wireless Bridge Device Information Table 3-26 Packing List Item Appearance Quantity Wireless Bridge × 1 PoE Power Supply × 1 AC Cord (Connect to the PoE × 1 Power Supply) Cable Tie × 2...
Page 110 Wireless Bridge Device Information Item Appearance Quantity Quick Start Guide × 1 Regulatory Compliance and × 1 Safety Information Note The device image used here is only for example purpose. The actual device may vary with models. Interface/Button Figure 3-62 CPE Device Interface/Button Table 3-27 Device Interface/Button Description Interface/...
Page 111 Wireless Bridge Device Information Interface/ B utton Description Note PoE OUT is not available when the device is powered by DC port. Reset Long press for 4 seconds to restore to factory settings. Indicator Figure 3-63 Device Indicator Table 3-28 Device Indicator Description Indicator Description Signal Strength...
Page 112 Wireless Bridge Device Information Indicator Description Power Indicator Solid Green The device is powered on normally Unlit No power supply connected or power supply is abnormal. Application Scene Figure 3-64 Application Scene Preparation for Installation To avoid device damage or personal injury caused by improper usage of the device, please follow the preparations below.
Page 113 Wireless Bridge Device Information Protect the PoE power supply from rain. It is suggested to put them into a waterproof case or ● keep them in a dry place. It is suggested to manage the gap between cover and device with fluid dispensing. ●...
Page 114 Wireless Bridge Device Information Figure 3-66 Fix Device Note Adjust the direction of the device manually to keep the device installed vertically. Device Connection CPE device can supply power to IPC. Note Use the attached PoE power supply to power on the device. ●...
Page 115: 5Ghz 5Km
Wireless Bridge Device Information Figure 3-67 CPE Connection After you finish the device connection, check device working status, network connection, and signal strength according to indicators. 3.5 5GHz 5km 3.5.1 DS-3WF02-5AC/D The 5 GHz wireless bridge (hereinafter referred to as the device) is used for wireless transmission within 5 km.
Page 116 Wireless Bridge Device Information Table 3-29 Packing List Item Appearance Quantity Wireless Bridge × 2 PoE Power Supply × 2 AC Cord (Connect to the PoE × 2 Power Supply) Cable Tie × 4...
Page 117 Wireless Bridge Device Information Item Appearance Quantity Quick Start Guide × 1 Regulatory Compliance and × 1 Safety Information Note The device image used here is only for example purpose. The actual device may vary with models. Interface/Button Figure 3-68 AP Device Interface/Button...
Page 118 Wireless Bridge Device Information Figure 3-69 CPE Device Interface/Button Table 3-30 Device Interface/Button Description Interface/ B utton Description Standard PoE IN/LAN 1 The 10/100 Mbps adaptive RJ45 port, also can be used as a standard PoE input port. LAN 2 The 10/100 Mbps adaptive RJ45 port.
Page 119 Wireless Bridge Device Information Indicator Figure 3-70 Device Indicator Table 3-31 Device Indicator Description Indicator Description Signal Strength Solid on The devices are matched. Indicator Solid red, yellow, and green: The wireless signal is ● strong. Solid red and yellow, unlit green: The wireless ●...
Page 120 Wireless Bridge Device Information Application Scene Figure 3-71 Application Scene Preparation for Installation To avoid device damage or personal injury caused by improper usage of the device, please follow the preparations below. Use the attached PoE power supply to power the device. ●...
Page 121 Wireless Bridge Device Information Pole Installation Mount the device on the pole with a diameter of 40 to 100 mm using the attached cable tie. Please read and follow the steps: 1. Thread the cable ties into the installation holes at the back of the device. Figure 3-72 Thread Cable Ties 2.
Page 122 Wireless Bridge Device Information Figure 3-73 Fix Device Note Adjust the direction of the device manually to keep the device installed vertically. Device Connection Based on the actual situations, connect the device according to the following wiring steps. Note Use the attached PoE power supply to power on the device. ●...
Page 123 Wireless Bridge Device Information Figure 3-74 AP Connection (With PoE Power Supply) Figure 3-75 AP Connection (With PoE Switch) 2. CPE connection: CPE device can supply power to IPC.
Page 124: Ds-3Wf02C-5Ac/O
Wireless Bridge Device Information Figure 3-76 CPE Connection 3. After you finish the device connection, check device working status, network connection, and signal strength according to indicators. 3.5.2 DS-3WF02C-5AC/O The 5 GHz wireless bridge (hereinafter referred to as the device) is used for wireless transmission within 5 km.
Page 125 Wireless Bridge Device Information Table 3-32 Packing List Item Appearance Quantity Wireless Bridge × 1 PoE Injector × 1 Power Adapter × 1 Cable Tie × 2 Quick Start Guide × 1 Regulatory Compliance and × 1 Safety Information Note The device image used here is only for example purpose.
Page 126 Wireless Bridge Device Information Interface/Button Figure 3-77 Device Interface/Button Table 3-33 Device Interface/Button Description Interface/ B utton Description CPE/AP DIP Switch Switch up or down to set the device as AP or CPE. SSID Switch up or down to set a 4-character SSID. CPE and AP will match when their SSIDs are the same.
Page 127 Wireless Bridge Device Information Table 3-34 SSID No. Introduction Indicator Figure 3-78 Device Indicator Table 3-35 Device Indicator Description Indicator Description Signal Strength Solid on The devices are matched. Indicator...
Page 128 Wireless Bridge Device Information Indicator Description Solid red, yellow, and green: The wireless signal is ● strong. Solid red and yellow, unlit green: The wireless ● signal is normal. Solid red, unlit yellow and green: The wireless ● signal is weak. Please adjust the position and direction of the device.
Page 129 Wireless Bridge Device Information Application Scene Figure 3-79 Application Scene Preparation for Installation To avoid device damage or personal injury caused by improper usage of the device, please follow the preparations below. Use the attached power adapter and PoE injector to power the device. ●...
Page 130 Wireless Bridge Device Information Pole Installation Mount the device on the pole with a diameter of 40 to 100 mm using the attached cable tie. Please read and follow the steps: 1. Thread the cable ties into the installation holes at the back of the device. Figure 3-80 Thread Cable Ties 2.
Page 131 Wireless Bridge Device Information Figure 3-81 Fix Device Note Adjust the direction of the device manually to keep the device installed vertically. Device Connection Based on the actual situations, connect the device according to the following wiring steps. Note Use the attached PoE injector and power adaptor to power on the device. ●...
Page 132: Ds-3Wf02C-5Ac/O V2
Wireless Bridge Device Information Figure 3-82 AP Connection 2. CPE connection: a. Switch the CPE/AP DIP to set the device as CPE. b. Select the SSID No. set on the AP to match (Select SSID NO. 1 for example). c. CPE device can supply power to IPC. d.
Page 133 Wireless Bridge Device Information Packing List Please check if there is any damage of the package first. According to the packing list, make sure no item is lost. After checking all the items included, you can continue to install the device. Table 3-36 Packing List Item Appearance...
Page 134 Wireless Bridge Device Information Note The device image used here is only for example purpose. The actual device may vary with models. Interface/Button Figure 3-84 Device Interface/Button Table 3-37 Device Interface/Button Description Interface/ B utton Description CPE/AP DIP Switch Switch up or down to set the device as AP or CPE. SSID Switch up or down to set a 4-character SSID.
Page 135 Wireless Bridge Device Information Note Please switch the CPE/AP DIP Switch to set which scene the device is used as before setting the SSID. Table 3-38 SSID No. Introduction Indicator Figure 3-85 Device Indicator...
Page 136 Wireless Bridge Device Information Table 3-39 Device Indicator Description Indicator Description Signal Strength Solid on The devices are matched. Indicator Solid red, yellow, and green: The wireless signal is ● strong. Solid red and yellow, unlit green: The wireless ● signal is normal.
Page 137 Wireless Bridge Device Information Application Scene Figure 3-86 Application Scene Preparation for Installation To avoid device damage or personal injury caused by improper usage of the device, please follow the preparations below. Use the attached power adapter and PoE injector to power the device. ●...
Page 138 Wireless Bridge Device Information Pole Installation Mount the device on the pole with a diameter of 40 to 100 mm using the attached cable tie. Please read and follow the steps: 1. Thread the cable ties into the installation holes at the back of the device. Figure 3-87 Thread Cable Ties 2.
Page 139 Wireless Bridge Device Information Figure 3-88 Fix Device Note Adjust the direction of the device manually to keep the device installed vertically. Device Connection Based on the actual situations, connect the device according to the following wiring steps. Note Use the attached PoE injector and power adaptor to power on the device. ●...
Page 140: Ds-3Wf02C-5Ac/O V3
Wireless Bridge Device Information Figure 3-89 AP Connection 2. CPE connection: a. Switch the CPE/AP DIP to set the device as CPE. b. Select the SSID No. set on the AP to match (Select SSID NO. 1 for example). c. CPE device can supply power to IPC. d.
Page 141 Wireless Bridge Device Information Packing List Please check if there is any damage of the package first. According to the packing list, make sure no item is lost. After checking all the items included, you can continue to install the device. Table 3-40 Packing List Item Appearance...
Page 142 Wireless Bridge Device Information Note The device image used here is only for example purpose. The actual device may vary with models. Interface/Button Figure 3-91 Device Interface/Button Table 3-41 Device Interface/Button Description Interface/ B utton Description SSID Switch up or down to set a 4-character SSID. CPE and AP will match when their SSIDs are the same.
Page 143 Wireless Bridge Device Information Interface/ B utton Description CPE/AP DIP Switch Switch left or right to set the device as AP or CPE. Reset Long press for 4 seconds to restore to factory settings. Network Cable Slot Reserved for easy placement of the network cables.
Page 144 Wireless Bridge Device Information Indicator Figure 3-92 Device Indicator Table 3-43 Device Indicator Description Indicator Description Signal Strength Solid on The devices are matched. Indicator Solid red, yellow, and green: The wireless signal is ● strong. Solid red and yellow, unlit green: The wireless ●...
Page 145 Wireless Bridge Device Information Application Scene Figure 3-93 Application Scene Preparation for Installation To avoid device damage or personal injury caused by improper usage of the device, please follow the preparations below. Use the attached power adapter and PoE injector to power the device. ●...
Page 146 Wireless Bridge Device Information Pole Installation Mount the device on the pole with a diameter of 40 to 100 mm using the attached cable tie. Please read and follow the steps: 1. Thread the cable ties into the installation holes at the back of the device. Figure 3-94 Thread Cable Ties 2.
Page 147 Wireless Bridge Device Information Figure 3-95 Fix Device Note Adjust the direction of the device manually to keep the device installed vertically. Device Connection Based on the actual situations, connect the device according to the following wiring steps. Note Use the attached PoE injector and power adapter to power on the device. ●...
Page 148: 5Ghz 15 Km
Wireless Bridge Device Information Figure 3-96 AP Connection 2. CPE connection: a. Switch the CPE/AP DIP to set the device as CPE. b. Select the SSID No. set on the AP to match (Select SSID NO. 1 for example). c. CPE device can supply power to IPC. d.
Page 149 Wireless Bridge Device Information Packing List Please check if there is any damage of the package first. According to the packing list, make sure no item is lost. After checking all the items included, you can continue to install the device. Table 3-44 Packing List Item Appearance...
Page 150 Wireless Bridge Device Information Note The device image used here is only for example purpose. The actual device may vary with models. Interface/Button Figure 3-98 Device Interface/Button Table 3-45 Device Interface/Button Description Interface/ B utton Description CPE/AP DIP Switch Switch up or down to set the device as AP or CPE. SSID Switch up or down to set a 4-character SSID.
Page 151 Wireless Bridge Device Information Note Please switch the CPE/AP DIP Switch to set which scene the device is used as before setting the SSID. Table 3-46 SSID No. Introduction Indicator Figure 3-99 Device Indicator...
Page 152 Wireless Bridge Device Information Table 3-47 Device Indicator Description Indicator Description Signal Strength Solid on The devices are matched. Indicator Solid red, yellow, and green: The wireless signal is ● strong. Solid red and yellow, unlit green: The wireless ● signal is normal.
Page 153 Wireless Bridge Device Information Application Scene Figure 3-100 Application Scene Preparation for Installation To avoid device damage or personal injury caused by improper usage of the device, please follow the preparations below. Use the attached power adapter and PoE injector to power the device. ●...
Page 154 Wireless Bridge Device Information Pole Installation Mount the device on the pole with a diameter of 40 to 100 mm using the attached cable tie. Please read and follow the steps: 1. Thread the cable ties into the installation holes at the back of the device. Figure 3-101 Thread Cable Ties 2.
Page 155 Wireless Bridge Device Information Figure 3-102 Fix Device Note Adjust the direction of the device manually to keep the device installed vertically. Device Connection Based on the actual situations, connect the device according to the following wiring steps. Note Use the attached PoE injector and power adaptor to power on the device. ●...
Page 156: Ds-3Wf03C-5Ac/O V2
Wireless Bridge Device Information Figure 3-103 AP Connection 2. CPE connection: a. Switch the CPE/AP DIP to set the device as CPE. b. Select the SSID No. set on the AP to match (Select SSID NO. 1 for example). c. CPE device can supply power to IPC. d.
Page 157 Wireless Bridge Device Information Packing List Please check if there is any damage of the package first. According to the packing list, make sure no item is lost. After checking all the items included, you can continue to install the device. Table 3-48 Packing List Item Appearance...
Page 158 Wireless Bridge Device Information Note The device image used here is only for example purpose. The actual device may vary with models. Interface/Button Figure 3-105 Device Interface/Button Table 3-49 Device Interface/Button Description Interface/ B utton Description CPE/AP DIP Switch Switch up or down to set the device as AP or CPE. SSID Switch up or down to set a 4-character SSID.
Page 159 Wireless Bridge Device Information Note Please switch the CPE/AP DIP Switch to set which scene the device is used as before setting the SSID. Table 3-50 SSID No. Introduction Indicator Figure 3-106 Device Indicator...
Page 160 Wireless Bridge Device Information Table 3-51 Device Indicator Description Indicator Description Signal Strength Solid on The devices are matched. Indicator Solid red, yellow, and green: The wireless signal is ● strong. Solid red and yellow, unlit green: The wireless ● signal is normal.
Page 161 Wireless Bridge Device Information Application Scene Figure 3-107 Application Scene Preparation for Installation To avoid device damage or personal injury caused by improper usage of the device, please follow the preparations below. Use the attached power adapter and PoE injector to power the device. ●...
Page 162 Wireless Bridge Device Information Pole Installation Mount the device on the pole with a diameter of 40 to 100 mm using the attached cable tie. Please read and follow the steps: 1. Thread the cable ties into the installation holes at the back of the device. Figure 3-108 Thread Cable Ties 2.
Page 163 Wireless Bridge Device Information Figure 3-109 Fix Device Note Adjust the direction of the device manually to keep the device installed vertically. Device Connection Based on the actual situations, connect the device according to the following wiring steps. Note Use the attached PoE injector and power adaptor to power on the device. ●...
Page 164: Ds-3Wf03C-5Ac/O V3
Wireless Bridge Device Information Figure 3-110 AP Connection 2. CPE connection: a. Switch the CPE/AP DIP to set the device as CPE. b. Select the SSID No. set on the AP to match (Select SSID NO. 1 for example). c. CPE device can supply power to IPC. d.
Page 165 Wireless Bridge Device Information Packing List Please check if there is any damage of the package first. According to the packing list, make sure no item is lost. After checking all the items included, you can continue to install the device. Table 3-52 Packing List Item Appearance...
Page 166 Wireless Bridge Device Information Note The device image used here is only for example purpose. The actual device may vary with models. Interface/Button Figure 3-112 Device Interface/Button Table 3-53 Device Interface/Button Description Interface/ B utton Description SSID Switch up or down to set a 4-character SSID. CPE and AP will match when their SSIDs are the same.
Page 167 Wireless Bridge Device Information Interface/ B utton Description CPE/AP DIP Switch Switch left or right to set the device as AP or CPE. Reset Long press for 4 seconds to restore to factory settings. Network Cable Slot Reserved for easy placement of the network cables.
Page 168 Wireless Bridge Device Information Indicator Figure 3-113 Device Indicator Table 3-55 Device Indicator Description Indicator Description Signal Strength Solid on The devices are matched. Indicator Solid red, yellow, and green: The wireless signal is ● strong. Solid red and yellow, unlit green: The wireless ●...
Page 169 Wireless Bridge Device Information Application Scene Figure 3-114 Application Scene Preparation for Installation To avoid device damage or personal injury caused by improper usage of the device, please follow the preparations below. Use the attached power adapter and PoE injector to power the device. ●...
Page 170 Wireless Bridge Device Information Pole Installation Mount the device on the pole with a diameter of 40 to 100 mm using the attached cable tie. Please read and follow the steps: 1. Thread the cable ties into the installation holes at the back of the device. Figure 3-115 Thread Cable Ties 2.
Page 171 Wireless Bridge Device Information Figure 3-116 Fix Device Note Adjust the direction of the device manually to keep the device installed vertically. Device Connection Based on the actual situations, connect the device according to the following wiring steps. Note Use the attached PoE injector and power adapter to power on the device. ●...
Page 172 Wireless Bridge Device Information Figure 3-117 AP Connection 2. CPE connection: a. Switch the CPE/AP DIP to set the device as CPE. b. Select the SSID No. set on the AP to match (Select SSID NO. 1 for example). c. CPE device can supply power to IPC. d.
Page 173: Chapter 4 First-Time Use
Wireless Bridge Device Information Chapter 4 First-Time Use 4.1 Activation For the security of your privacy and system data, you are required to set a password for your first use. After the password is set, you can log in to the web for further configuration. Activate with Wireless Connection Steps 1.
Page 174 Wireless Bridge Device Information Activate with Wired Connection Step 1. Power on the wireless bridge by the accessories in the package. Note The accessories vary with different models. Please check Device Information on Quick Start Guide. 2. Connect the LAN port on your device to the network port on your PC via an Ethernet cable. 3.
Page 175: Login
Wireless Bridge Device Information Note Check the label on the back of your device to confirm IP Address. 5. Set your password and confirm. Caution - The password strength of the device can be automatically checked. We highly recommend you change the password of your own choosing (using a minimum of 8 characters, including at least three kinds of following categories: uppercase letters, lowercase letters, numbers, and special characters) in order to increase the security of your product.
Page 176: Device Pairing
Wireless Bridge Device Information 4.3 Device Pairing Device Packing in Pairs Devices packing in pairs will match with each other automatically after being activated. Device with DIP Switch Step 1. Set the AP/CPE DIP Switch on the devices. Make sure that one device is set as AP, other devices are set as CPE.
Page 177: Chapter 5 Remote Management
Table 5-1 Link of Operation Tool Operation Tool Link Web Browser Click here for the User Manul. Note Click here for the User Manual of DS-3WF0BC-2NT(B). iVMS-4200 Client Click here for the User Manul. SADP Software Click here for the User Manul. HikCentral Professional HikCentral Professional Web Client: Click here for the User ●...
Page 178: Chapter 6 Faq
Wireless Bridge Device Information Chapter 6 FAQ 6.1 Why Devices Pairing Failed? Reason The devices pairing status depends on the distance, direction, SSID name, and PSK password. Solution You can check as follows: 1. Check distance and direction: Ensure the AP and CPE are directly faced to each other, and the distance between them is within the limit.
Page 179: Why The Throughput Is Inadequate Even With High Signal Quality
Wireless Bridge Device Information 6.4 Why the Throughput Is Inadequate Even with High Signal Quality? Reason 1. Excessive interference or multipath interference. 2. Wired device error. Solution 1. Remove the interference or change the device frequency. Note Method of changing frequency: Reboot the AP of wireless bridge to allow auto search of available signal channels.
Page 180 UD40155B...

This manual is also suitable for:

Ds-3wf0bc-2nt bDs-3wf0ec-2nt Ds-3wf0ec-5actDs-3wf0ec-5act bDs-3wf500-ei-2n Ds-3wf500s-ei-2n ... Show all

HIKVISION DS-3WF0BC-2NT Documentation

Quick Links

Need help?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for HIKVISION DS-3WF0BC-2NT

Summary of Contents for HIKVISION DS-3WF0BC-2NT

This manual is also suitable for:

Table of Contents