HIKVISION DS-3WF02-5AC/D User Manual
  1. Manuals
  2. Brands
  3. HIKVISION Manuals
  4. Wireless Access Point
  5. DS-3WF02-5AC/D
  6. User manual
HIKVISION DS-3WF02-5AC/D User Manual

HIKVISION DS-3WF02-5AC/D User Manual

Wireless bridge (web)
Hide thumbs Also See for DS-3WF02-5AC/D:
Table of Contents

Advertisement

Quick Links

Download this manual
Wireless Bridge (Web)
User Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the DS-3WF02-5AC/D and is the answer not in the manual?

Questions and answers

Related Manuals for HIKVISION DS-3WF02-5AC/D

Summary of Contents for HIKVISION DS-3WF02-5AC/D

  • Page 1 Wireless Bridge (Web) User Manual...

  • Page 2: Legal Information

    Document, which may include licenses obtained from third parties. ● Any part of the Document, including text, pictures, graphics, etc., belongs to Hikvision. No part of this Document may be excerpted, copied, translated, or modified in whole or in part by any means without written permission.
  • Page 3 Wireless Bridge (Web) • User Manual RISKS, AND HIKVISION SHALL NOT TAKE ANY RESPONSIBILITIES FOR ABNORMAL OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER-ATTACK, HACKER ATTACK, VIRUS INFECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER, HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED.

  • Page 4: Applicable Models

    Wireless Bridge (Web) • User Manual Preface Applicable Models This manual is applicable to the wireless bridge for web operation. Symbol Conventions The symbols that may be found in this document are defined as follows. Symbol Description Indicates a hazardous situation which, if not avoided, will or could Danger result in death or serious injury.

  • Page 5: Table Of Contents

    Wireless Bridge (Web) • User Manual Contents Introduction ....................... 1 Activation and Login ....................2 Activate the Device ........................ 2 Log in to the Device ........................ 2 Overview........................3 Network Settings ......................5 WAN Settings ......................... 5 LAN Settings ........................... 6 Data Forwarding Settings .......................
  • Page 6 Wireless Bridge (Web) • User Manual Why the wireless connection rate is relatively low? ............23 Why the signal intensity is too low? .................. 24 Why the throughput is inadequate even with high signal quality? ........24 Why there are excessive packet loss and time delay when PC pings the device IP address? ..............................

  • Page 7: Introduction

    Wireless Bridge (Web) • User Manual Introduction You can manage and configure the wireless bridge (hereinafter referred to as the device) through the web browser, including network settings, wireless network settings, and system management. Note Functions vary with device models. Pictures used for illustration here are for example purposes. The actual interface prevails.

  • Page 8: Activation And Login

    Wireless Bridge (Web) • User Manual Activation and Login Activate the Device For the security of your privacy and system data, you are required to set a password for your first use. After the password is set, you can log in to the web for further configuration. Before You Start Ensure that your PC and the device are on the same network segment.

  • Page 9: Overview

    Wireless Bridge (Web) • User Manual Overview You can view the basic information, connection status, network status, and wireless status for routine check or device maintenance. Overview Overview Description Information&Operation Description Check device name, device model, serial No., program version, MAC Device Information address, CPU usage, memory usage, running time, and background noise condition of the device, etc.
  • Page 10 Wireless Bridge (Web) • User Manual 7days. See Chapter 7 PoE Management for details. Cloud Platform Check clound platform connection status, or scan the QR code to add advice in the APP. See Chapter 6 VLAN Management for details. Quick Set Time Click Set Now to set system time.

  • Page 11: Network Settings

    Wireless Bridge (Web) • User Manual Network Settings WAN Settings Go to Network Settings → LAN Settings to set relevant parameters, such as Network Access Method and WAN IPv4. Note The function varies with models, and it is only supported when some devices are set as AP site. The actual interface prevails.

  • Page 12: Lan Settings

    Wireless Bridge (Web) • User Manual LAN Settings Go to Network Settings → LAN Settings to configure detailed network parameters. If you enable Auto-obtain Dynamic IP, other parameters will be set automatically. LAN Settings Note  The function varies with models. Devices with WAN port is supported to configure DHCP server.
  • Page 13 Wireless Bridge (Web) • User Manual Enable Self-Adaptive Packet Filtering Disable Self-Adaptive Packet Filtering Parameter Description Parameter Description Self-Adaptive Enabled by default. Filter packets according to present rules, in order to Packet Filtering reduce the impact of excessive message on the device in the LAN. Filter SADP multicast packets to minimize the negative influence brought by massive SADP multicast packets in the LAN.

  • Page 14: Wireless Settings

    Wireless Bridge (Web) • User Manual Wireless Settings Click Wireless Settings to set basic and advanced parameters of wireless network. Basic Wireless Settings Go to Wireless Settings → Basic Settings to set wireless network basic parameters. Wireless Network Basic Settings Note The picture used above is an example of a device with DIP switch function.
  • Page 15 Wireless Bridge (Web) • User Manual Parameter Description Parameter Description Enable/disable the pairing code and scene switching function through the DIP switch. This function is enabled by default. Note Enable DIP Switch ● If the DIP group numbers are not enough for use, you can disable this function and set SSID accordingly.

  • Page 16: Advanced Wireless Settings

    Wireless Bridge (Web) • User Manual Parameter Description The power transmitted in the direction of peak radiation to that of an Antenna Gain isotropic source. Click Scan and select an optimum channel to check the signal intensity of Signal Scanning available channels nearby.

  • Page 17: Admin Ssid

    Wireless Bridge (Web) • User Manual Admin SSID Support mobile phones and PCs to manage AP/CPE device by connecting to the device wireless network, for configuration such as setup and maintenance. Note  The function is only available for some models. The actual interface prevails. ...

  • Page 18: Vlan Management

    Wireless Bridge (Web) • User Manual VLAN Management VLAN (Virtual Local Area Network) is a technology that logically (rather than physically) divides devices within a local area network into individual network segments, thereby achieving the isolation of broadcast domains within a local area network. Note The function is only available for some models.

  • Page 19: Poe Management

    Wireless Bridge (Web) • User Manual PoE Management Click PoE Management to manage PoE port as desired. Note The function is only available for some models. The actual interface prevails. PoE Management Enabling PoE watchdog can automatically detect the connection status of devices connected to the PoE port.

  • Page 20: Terminal Security

    Wireless Bridge (Web) • User Manual Terminal Security Go to Terminal Security and select the appropriate mode. The device can identify the brand of terminals and match security policies to achieve terminal classification management. Note The function is only available for some models. The actual interface prevails. Terminal Security ...

  • Page 21: System Configuration

    Wireless Bridge (Web) • User Manual System Configuration Cloud Platform Access Configure Cloud Platform Parameter Description Parameter Description Enable After it is enabled, the device will connect to the HIK-Connect platform. Ensure that the device is connected to the public network.

  • Page 22: Ping Tool

    Wireless Bridge (Web) • User Manual Export desired logs to your local storage. Steps 1. Go to Diagnosis → Log Management. 2. Click Export to save the log files. Through Ping Tool, you can get network status information, which would be useful for the technical support.

  • Page 23: Save Debugging Information

    Wireless Bridge (Web) • User Manual 2. Click Test to get the results (including Source IP, Target IP, Average Bandwidth, and Minimum Bandwidth). Save debugging information of different print levels to the flash, and the saved information can be restored even after the device is powered off and rebooted, making it easier for technical support personnel to investigate the cause and perform later maintenance.

  • Page 24: Http(S)

    Wireless Bridge (Web) • User Manual The HTTP protocol (Hypertext Transfer Protocol) is an application layer transport protocol based on the TCP protocol, while the HTTPS protocol (Secure Hypertext Transfer Protocol) is a network protocol built on SSL+HTTP protocol that can perform encrypted transmission and identity authentication.

  • Page 25: Reboot The Device

    Wireless Bridge (Web) • User Manual SADP Service Note If SADP service is disabled, some of the functions may become unavailable. It is recommended to enable this service. Reboot the Device You can reboot the device remotely through the web page. Steps 1.

  • Page 26: Upgrade The Device

    Wireless Bridge (Web) • User Manual Upgrade the Device Use the newest firmware for available upgrades, and upgrade the device through web page remotely. Before You Start Copy the upgrade package to the local directory of the PC used for remote access. Steps 1.

  • Page 27: Manual Setting

    Wireless Bridge (Web) • User Manual 4. Set the desired time or check Sync. With Computer Time. Manual Setting 5. Click Save. NTP time synchronization is used to synchronize the time with that of a specific NTP server. Steps 1. Go to System → System Configuration → Time Configuration. 2.

  • Page 28: Change Password

    Wireless Bridge (Web) • User Manual The IP address of the NTP server. NTP Port Monitoring port of the NTP server. Default value: 123. Value range: 1 to 65535. Sync. Interval The frequency for the device to synchronize with the NTP server. Value range: 1 to 10080 minutes.

  • Page 29: Faqs

    Wireless Bridge (Web) • User Manual FAQs Why the device cannot start up? Reason 1. The network cable length connecting the wireless bridge to the PoE module exceeds 60 m. 2. The network cable cannot meet the standard of Category 5e. 3.
  • Page 30 Wireless Bridge (Web) • User Manual Why the signal intensity is too low? Reason 1. There is a large-sized obstruction between the CPE and the AP. 2. The CPE is not directly faced to the AP. Solution 1. Remove the obstruction or bypass it. Adjust the angle of the CPE and the AP.
  • Page 31 UD40954B...

This manual is also suitable for:

Ds-3wf0ec-2ntDs-3wf0bc-2ntDs-3wf0fc-2n/oDs-3wf0ec-5actDs-3wf0fa-2n/oDs-3wf0ec-5actb ... Show all

Table of Contents