Related Manuals for MSI MS-5966 SmartLink HAMR5603
Summary of Contents for MSI MS-5966 SmartLink HAMR5603
- Page 1 User’s Guide MS-5966 SmartLink HAMR5603 Modem Riser Card M S - 5966 SmartLink HAMR5603 Modem Riser Card User’s Guide VERSION 1.0 1999/07/15 ROC...
- Page 2 User’s Guide MS-5966 SmartLink HAMR5603 Modem Riser Card FCC-B Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
-
Page 3: Fcc Requirement
User’s Guide MS-5966 SmartLink HAMR5603 Modem Riser Card FCC Requirement This equipment complies with Part 68 of the FCC Rules. On the bottom of this equipment is a label that contains, among other information, the FCC registration Number, Ringer Equivalence Number (REN) and USOC jack type for this equipment. You must, upon request, provide this information to your telephone company. -
Page 4: Ctr 21 Approval
User’s Guide MS-5966 SmartLink HAMR5603 Modem Riser Card CTR 21 approval This equipment has been approved to [Council Decision 98/482/EC - “CTR 21”] for pan-European single terminal connection to the Public Switched telephone Network (PSTN). However, due to differences between the individual PSTNs provided in different countries, the approval does not, of itself, give an unconditional assurance of successful operation on every PSTN termination point. -
Page 5: Table Of Contents
User’s Guide MS-5966 SmartLink HAMR5603 Modem Riser Card Table of Contents Specifications of MS-5966 ..........6 What is HAMR56xx ....................Installation and Setup..............7 First-Time Installation..............8 Verifying Correct Installation ........... 12 Uninstalling the HAMR56xx drivers ......... 14 Modem Troubleshooting ............16 Appendix A: AT Commands ........... 18 Appendix B: S-Registers ............ -
Page 6: Specifications Of Ms-5966
User’s Guide MS-5966 SmartLink HAMR5603 Modem Riser Card Specifications of MS-5966 Line data rate 56000, 54000, 50000, 48000, 46000, 44000, 42000, 40000, 38000, 36000, 34000, 33600, 32100, 28800, 26400, 24000, 19200, 16800, 14400, 12000, 9600, 7200,4800,2400,1200,600,300 Modem Protocol V.90 and backward compatible Chipset Smart Link HAMR56xx host modem chipset. -
Page 7: System Requirements
User’s Guide MS-5966 SmartLink HAMR5603 Modem Riser Card HAMR56xx supports the standard modem, fax and voice interfaces via TAPI and AT commands, and will run all communication applications which adhere to these standards. System Requirements Pentium based PC (200 MHz and above) Windows 95/98/NT Operating system AMR slot 8 MB RAM (The HAMR56xx software, when running, occupies around... -
Page 8: First-Time Installation
User’s Guide MS-5966 SmartLink HAMR5603 Modem Riser Card First-Time Installation Step 1: Install the HAMR56xx card 1. Turn off your computer. Note: Some PCI 2.2 compliant motherboards supply power to the slots even when the PC is turned off. To prevent damage to your PC or MR card, always remove the power cord when installing or removing MR cards. - Page 9 User’s Guide MS-5966 SmartLink HAMR5603 Modem Riser Card 1. A New Hardware Found dialog box will appear when the MR card is detected and will prompt for the driver disk. 2. Insert the Device Driver disk, and click Next. 3. Select Search for the best driver for your device and click Next.
- Page 10 User’s Guide MS-5966 SmartLink HAMR5603 Modem Riser Card 4. In the next dialog box, enter the disk drive of the installation disk or click the Browse button and point to the location of the driver installation files. 5. Click Next. 6.
- Page 11 User’s Guide MS-5966 SmartLink HAMR5603 Modem Riser Card 9. After files have been copied, a dialog box similar to the following will appear: 10. Click Finish. 11. A country selection dialog box will now appear Select your country from the list, select enable PBX if you use the internal phone line, and then click Ok.
-
Page 12: Verifying Correct Installation
User’s Guide MS-5966 SmartLink HAMR5603 Modem Riser Card Verifying Correct Installation After installing the MR card drivers, you should check that you modem has been installed correctly, as described below: Step 1: Go to Start > Settings > Control Panel. Step 2: Double click on the Modems icon. - Page 13 User’s Guide MS-5966 SmartLink HAMR5603 Modem Riser Card Step 4: Click on Diagnostics tab. Step 5: Select the port which HAMR56xx is connected to, and click More Info. If installation was successful, you should see a screen similar to this one: If you see anything else – refer to the “Trouble- shooting”...
-
Page 14: Uninstalling The Hamr56Xx Drivers
User’s Guide MS-5966 SmartLink HAMR5603 Modem Riser Card Uninstalling the HAMR56xx drivers If your system already has the MR drivers installed, you can install a new version. However, you must first uninstall the current drivers, using the following procedures: Step 1: Open the Control Panel from the Start/Settings menu. Step 2: In the Control Panel, double-click on the add/Remove Programs icon. - Page 15 User’s Guide MS-5966 SmartLink HAMR5603 Modem Riser Card Step 4: Click OK. MR drivers and devices will now be uninstalled. Note: If you want to upgrade the drivers. You need to Uninstall the older driver first. Then, restart the PC and install new drivers when prompted to.
-
Page 16: Modem Troubleshooting
User’s Guide MS-5966 SmartLink HAMR5603 Modem Riser Card Modem Troubleshooting This section provides help for problems that may be encountered when trying to use the modem. Problem 1: If ERROR, NO DIALTONE or a similar message is received, or no RING is identified: Possible Solution: 1. - Page 17 User’s Guide MS-5966 SmartLink HAMR5603 Modem Riser Card Problem 3: If you cannot hear the dialtone and DTMF dialing while the modem should be dialing out: Possible Solution: MS-5966 hardware designs typically support three methods for monitoring call progress (dialtone, DTMF dialing, etc...) 1.
-
Page 18: Appendix A: At Commands
User’s Guide MS-5966 SmartLink HAMR5603 Modem Riser Card Appendix A: AT Commands Modem operation is controlled by AT commands. These AT commands include the following: • Basic AT commands, for example ATDT123 • Extended AT Commands for example AT&E,AT\A,AT%C,AT+MS • S-Register commands, for example ATS32=8 •... -
Page 19: At Command Set
User’s Guide MS-5966 SmartLink HAMR5603 Modem Riser Card • The AT command sequence may be followed by any number of commands in sequence, with the exception of commands Z, D or A, where all characters following on the same command line will be ignored. -
Page 20: Appendix B: S-Registers
User’s Guide MS-5966 SmartLink HAMR5603 Modem Riser Card Appendix B: S-Registers The S-Registers are summarized in the following table. Factory defaults Factory defaults are stored in the Windows OS registry. They are loaded at initialization time or by AT commands (&F,Z). In addition, the designated default profile (as specified by the Yn command) is subsequently loaded.
Need help?
Do you have a question about the MS-5966 SmartLink HAMR5603 and is the answer not in the manual?
Questions and answers