Subscribe to Our Youtube Channel
Related Manuals for Motorline professional MC160
Summary of Contents for Motorline professional MC160
- Page 1 MC160 USER/INSTALLER MANUAL MENU RS DW ST UP LE LA LB LC M1 M2 EB RS DW ST UP V1.3 REV. 02/2025 HW 0.0.0 | H0.REV103...
-
Page 2: Table Of Contents
Travessa do Sobreiro, n.º 29, 4755-474 Rio Côvo (Santa Eugénia), Barcelos, declares that the present type of radio equipment - MC160 Control board The different types of packaging (cardboard, plastic, etc.) must be - ecomplies with the Directive 2014/53/EU. -
Page 3: Safety Instructions
01. SAFETY INSTRUCTIONS GENERAL WARNINGS • Children shouldn’t play with the product or opening devices to avoid the motorized door or gate from being triggered involuntarily. • This manual contains very important safety and usage information. • If the power cable is damaged, it must be replaced by the Read all instructions carefully before beginning the installation/ manufacturer, after-sales service or similarly qualified personnel usage procedures and keep this manual in a safe place that it can... -
Page 4: Warnings For Users
01. SAFETY INSTRUCTIONS the power supply cable. Please note that all the cables must enter conditions have been met. the control board from the bottom. • In the event of tripping of circuits breakers of fuse failure, locate • If the automatism is to be installed at a height of more than 2,5m the malfunction and solve it before resetting the circuit breaker or from the ground or other level of access, the minimum safety and replacing the fuse. -
Page 5: Control Board
02. CONTROL BOARD 02. CONTROL BOARD TECHNICAL CHARACTERISTICS CONNECTORS RS DW ST UP The MC160 is an electronic control board for automation of fire curtains. • SEC1 power supply SEC1: 22Vac | SEC2: 20Vac LE LA LB LC M1 M2 EB RS DW ST UP •... -
Page 6: Key Selector
02. CONTROL BOARD 02. CONTROL BOARD CONNECTORS KEY SELECTOR Function present on the control board cover Key Selector Position ALARM OPENED CLOSED FAULT If it is in the Auto position it means it 23 24 25 26 27 28 29 30 32 33 Auto is in normal operation. -
Page 7: Essential Steps For Installation
02. CONTROL BOARD 02. CONTROL BOARD ESSENTIAL STEPS FOR INSTALLATION CURTAIN OPERATION IN CASE OF FIRE 01 • Connect all accessories according to the connection diagram (page 15). • The control board goes into fire mode when one of the inputs LA, LB, LC is activated, or there is a power 02 •... -
Page 8: Control Panel Signaling
02. CONTROL BOARD 02. CONTROL BOARD VISUAL AND AUDIBLE ALARM REMOTE CONTROL The control board can control a siren and a flashing light to signal the fire alarm. The siren can also be used to signal that there is an obstruction in the curtain passageway, see parameter P5->Ob. -
Page 9: Program
03. PROGRAM 03. PROGRAM FUNCTIONS MENU P PROGRAM "P" • To access the P menu, press the MENU button for at least 2 seconds. COURSE PROGRAMMING • Use ↓↑ to navigate through the menus. • Press MENU whenever you want to confirm access to a menu. •... - Page 10 03. PROGRAM 03. PROGRAM PROGRAM "P" PROGRAM "P" FORCE AND SENSITIVITY ADJUSTMENT INTERMEDIATE STOP/DELAY Allows you to regulate the force and sensitivity of the motor Sets curtain behavior in alarm mode Force/speed adjustment Adjusting the position of the intermediate stop Allows you to regulate the force/speed with which the curtain will move.
- Page 11 03. PROGRAM 03. PROGRAM PROGRAM "P" PROGRAM "P" LA INPUT PROGRAMMING - ALARM SIGNAL RESET/STOP Manual reset Disable Allows you to activate or deactivate Whenever an alarm signal is given in the electronic control board, the the alarm signal input. (Factory value) curtain will close and remain in error until a manual remote control is Activates...
- Page 12 03. PROGRAM 03. PROGRAM PROGRAM "P" MENU FUNCTIONS E • To access the E menu, press the MENU button for at least 8 seconds. FLASHING LIGHT • Use ↓↑ to navigate through the menus. Allows you to set the flashing light operating mode in alarm mode. •...
-
Page 13: Program E
03. PROGRAM 03. PROGRAM PROGRAM "E" PROGRAM "E" PROGRAMMING THE LB AND LC INPUT HUMAN PRESENCE The LB and LC inputs have an 8K2 resistive contact and are used to connect smoke detectors or other types of sensors that operate resistively. This way, whenever these detectors are activated, the output will Disable human presence send an alarm signal to the curtain, which will then act according to the selected parameters. - Page 14 03. PROGRAM 03. PROGRAM PROGRAM "E" PROGRAM "E" RELAY POLARITY ELECTRIC BRAKE Defines the operating mode of the output relays to indicate the status of the control board. The control board allows the connection of an electric brake to the EB output. This electric These relays can be used in BMS (Building Management System) systems to indicate to the system brake will act whenever the control board is stopped, if the electric brake is normally open.
-
Page 15: Display
04. DISPLAY 03. PROGRAM PROGRAM "E" DISPLAY INDICATIONS MANEUVER COUNTER MENU DESCRIPTION This menu allows you to check how many complete maneuvers were performed by the In the stopped position, fully open control board (complete maneuver means opening and closing). In the stopped position, intermediate position Example: 130 371 maneuvers... -
Page 16: Connection Diagram
05. CONNECTION DIAGRAM CONNECTION DIAGRAM Connect when installation is complete • Batteries Black 24V 7A Máx. • Photocell • Power supply 230Vac • Encoder Buzzer COM NC/ MENU • Fire central • Motor • Key Selector RS DW ST UP on the cover •...
Need help?
Do you have a question about the MC160 and is the answer not in the manual?
Questions and answers