Advertisement

Quick Links

MC90BL-BR
USER/INSTALLER MANUAL
U
V
W
SEC 2
SEC 1
BAT
LMP
MOT
LED
ENC
ANT
MENU
UP
CMD
DW
PWR
A
B
V+ Y R
G B
GND
+ R G B
+12V-
LO
LS FO FC
LE LA LB
LO
LS FO FC
LE
LA
LB
TS
V+
EN
v1.2 REV. 04/2024
Compatible hardware versions:
HW 0.1.0 | FW H0.REV110

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the MC90BL-BR and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Motorline professional MC90BL-BR

  • Page 1 MC90BL-BR USER/INSTALLER MANUAL MENU V+ Y R + R G B +12V- LS FO FC LE LA LB LS FO FC SEC 2 SEC 1 v1.2 REV. 04/2024 Compatible hardware versions: HW 0.1.0 | FW H0.REV110...
  • Page 2: Table Of Contents

    00. CONTENT 01. SAFETY INSTRUCTIONS INDEX This product is certified in accordance with European Community 01. SAFETY INSTRUCTIONS (EC) safety standards. STANDARDS TO FOLLOW This product complies with Directive 2011/65/EU of the European Parliament and of the Council, of 8 June 2011, on the restriction 02.
  • Page 3: Safety Instructions

    01. SAFETY INSTRUCTIONS GENERAL WARNINGS • Children shouldn’t play with the product or opening devices to avoid the motorized door or gate from being triggered involuntarily. • This manual contains very important safety and usage information. • If the power cable is damaged, it must be replaced by the Read all instructions carefully before beginning the installation/ manufacturer, after-sales service or similarly qualified personnel usage procedures and keep this manual in a safe place that it can...
  • Page 4 01. SAFETY INSTRUCTIONS the power supply cable. Please note that all the cables must enter conditions have been met. the control board from the bottom. • In the event of tripping of circuits breakers of fuse failure, locate • If the automatism is to be installed at a height of more than 2,5m the malfunction and solve it before resetting the circuit breaker or from the ground or other level of access, the minimum safety and replacing the fuse.
  • Page 5: Control Board

    02. CONTROL BOARD TECHNICAL SPECIFICATIONS CONNECTORS The MC90BL-BR is an electronic control board for controlling brushless motors with a built-in radio control system, developed for automating barriers. 28 29 30 31 32 33 34 35 22 23 24 25 26 27...
  • Page 6: Buttons And Leds 5A

    02. CONTROL BOARD 03. INSTALLATION CONNECTORS INSTALLATION OF MCONNECT LINK (OPTIONAL) MENU MENU MENU 36 • Type-C input for MCONNECT LINK connection LINK 37 • Connector for flashing light RGB 38 • Connector for motor encoder V+ Y R 39 • Antenna connector (hot pole) + R G B +12V- LS FO FC...
  • Page 7: Programming

    03. INSTALLATION 04. PROGRAMMING ESSENTIAL STEPS FOR INSTALLATION REMOTE CONTROLS 01 • Make the connections of all the accessories according to the connection scheme (page 15 and 16). 02 • Connect the transformer to a power supply. 03 • Make sure that the barrier movement is the same as the one shown on the display: Programming a remote control for pedestrian Programming a remote control for full opening opening...
  • Page 8: P Menu Functions 7A

    04. PROGRAMMING 04. PROGRAMMING "P" MENU FUNCTIONS PROGRAMMING "P" FACTORY MENU FUNCTION MIN. MAX. STATE PAGE COURSE PROGRAMMING VALUE Automatic Programming Automatic course programming Master This menu allows you to automatic programming of the motor and slowdown. Slave Automatic programming: COURSE PROGRAMMING Left opening 01 •...
  • Page 9 04. PROGRAMMING 04. PROGRAMMING PROGRAMMING "P" PROGRAMMING "P" SLOWDOWN ADJUSTMENT PARTIAL COURSE ADJUSTMENT This menu allows to set the slowdown time at opening and closing. Partial mode allows the barrier to be opened to allow people to pass through. In this function you can define the percentage of course that you want the barrier to open in partial mode, in relation to the total course (100%).
  • Page 10 04. PROGRAMMING 04. PROGRAMMING PROGRAMMING "P" PROGRAMMING "P" PHOTOCELLS 1 PROGRAMMING PHOTOCELLS 2 PROGRAMMING Allows to program the security behavior LE (photocell 1). Allows to program the security behavior LA (photocell 2). Disable photocells Disable photocells Enable or disable security entry. Enable or disable security entry.
  • Page 11 04. PROGRAMMING 04. PROGRAMMING PROGRAMMING "P" PROGRAMMING "P" OPERATING LOGIC REMOTE PROGRAMMING This menu allows to set the operating logic of the automation. This menu allows to enable or disable the programming of new remote control without directly accessing the control board, using a previously stored remote control Automatic Mode (memorize remote controls page 6A).
  • Page 12: E Menu Functions 11A

    02. CONTROL BOARD 04. PROGRAMMING "E" MENU FUNCTIONS PROGRAMMING "E" FACTORY HUMAN PRESENCE/PUSHBUTTON MENU FUNCTION MIN. MAX. STATE PAGE VALUE Disables human presence Disables Human presence Active at closing Whenever an order is sent to the Active during opening and closing LO input and the barrier performs a Human presence HUMAN PRESENCE...
  • Page 13 04. PROGRAMMING 04. PROGRAMMING PROGRAMMING "E" PROGRAMMING "E" CALIBRATION FOLLOW ME This menu allows you to calibrate the barrier's course with the encoder when reaches the number of maneuvers selected for calibration. Function disabled This menu allows activating The range of maneuvers for calibration corresponds to the formula: value selected in Function activated after opening the Follow me option.
  • Page 14 04. PROGRAMMING 04. PROGRAMMING PROGRAMMING "E" PROGRAMMING "E" UNUSED RESET - RESET FACTORY VALUES This parameter has no assigned function. Disabled (Default value) Reset enabled SLOWDOWN SPEED This menu allows you to adjust the slowdown speed. 01 • Press MENU for 8 sec. until it appears 02 •...
  • Page 15: Display

    05. DISPLAY DISPLAY INDICATIONS MENU DESCRIPTION MENU DESCRIPTION In stop position, fully open Processing error In stop position, intermediate position Overvoltage error In stop position, fully closed Under voltage error Full opening button pressed Startup error Pedestrian opening button pressed Encoder error Control board performs the opening course EEPROM memory error...
  • Page 16: Connection Diagram

    06. CONNECTION DIAGRAM BARRIER...
  • Page 17: Mm90-Rgb Module (Optional)

    06. CONNECTION DIAGRAM 06. CONNECTION DIAGRAM MM90-RGB MODULE (OPTIONAL) MASTER / SLAVE (OPTIONAL) MENU MENU • MM90-RS485 Module V+ Y R + R G B + R G B +12V- +12V- LS FO FC LE LA LB LS FO FC SEC 2 SEC 1 V+ Y R G B...
  • Page 18: Troubleshooting

    07. TROUBLESHOOTING INSTRUCTIONS FOR FINAL CONSUMERS/TECHNICIANS Anomaly Procedure Behavior Procedure II Discovering the origin of the problem 1 • Open control board and check if it has power supply. • Make sure you have power • Motor doesn’t supply connected to the •...

Table of Contents