Advertisement
Advertisement
Related Manuals for Motorline professional MC50SE
Summary of Contents for Motorline professional MC50SE
- Page 1 MC50SE USER/INSTALLER MANUAL v7.0 REV. 04/2019...
-
Page 2: Table Of Contents
00. CONTENT INDEX 01. SAFETY INSTRUCTIONS 07. COMPONENTS TEST TEST SCHEME STANDARDS TO FOLLOW INPUTS TEST 02. THE CONTROL BOARD 08. TROUBLESHOOTING TECHNICAL SPECIFICATIONS INSTRUCTIONS FOR FINAL CONSUMERS/ TECHNICIANS PROGRAMMING PRE-RECOMENDATIONS 09. CONNECTION SCHEME 03. INSTALLATION CONTROL BOARD CONNECTIONS ESSENTIAL STEPS FOR INSTALLATION TRANSMITTERS "P"... -
Page 3: Safety Instructions
SAFETY INSTRUCTIONS STANDARDS TO FOLLOW TECHNICAL SPECIFICATIONS The MC50SE is a monophasic control board com a control system via incorporated rádio, ATTENTION: developed for the automation of sectional door. This product is certified in accordance with European Community (EC) safety standards. -
Page 4: The Control Board
02. THE CONTROL BOARD 02. THE CONTROL BOARD TECHNICAL SPECIFICATIONS PROGRAMMING PRE-RECOMENDATIONS 01 • Safety Edge LS • LED lit when the close push button is active 02 • Photocells LO • LED lit when the open push button is active 03 •... -
Page 5: Installation
03. INSTALLATION 03. INSTALLATION ESSENTIAL STEPS FOR INSTALLATION TRANSMITTERS The installation process assumes that the gate has already limit switches Transmitter programming for total opening. plates installed. For more information consult the motor's manual. • PROGRAMMING TRANSMITTERS • ERASE TRANSMITTERS 01 •... -
Page 6: Programming (P
03. INSTALLATION 03. INSTALLATION "P" MENU FUNCTIONS "E" MENU FUNCTIONS • We can only go into programming with a electrically closed gate. • We can only go into programming with a electrically closed gate. • To access the P menu •... - Page 7 04. PROGRAMMING "P" 04. PROGRAMMING "P" COURSE AUTOMATIC PROGRAMMING SETTING THE DECELERATION TIME This menu allows you to set the motor's working time. During the automatic programming, the motor performs the following maneuvers: Opening deceleration Closing deceleration Allows you to set the time that Allows you to set the time 1º...
-
Page 8: Display
04. PROGRAMMING "P" SETTING STRENGTH AND SENSITIVITY P3 MENU DISABLE. 04. PROGRAMMING "P" PAUSE TIME If the control board has very high sensitivity values, you may see the LI error. After four attempts, the LI error will turn ER. You will have to wait 10 sec. to return to program the automatism. Pause time adjustment of the total closure Allows you to set the... - Page 9 04. PROGRAMMING "P" 04. PROGRAMAR "P" PHOTOCELLS PROGRAMMING STOP 00 (disables photocells) 00 (photocells during the closing) 01 (ables photocells) 01 (photocells during the opening) With the photocells activated, when This menu can only be changed someone interrupts them, the gate when the HE menu is active.
- Page 10 04. PROGRAMMING "P" 04. PROGRAMMING "P" OPERATING LOGIC FLASHING LIGHT Functioning in automatic Functioning in step by Functioning in mode step mode condominium mode Intermittent During movement of Courtesy light Does not accept orders 1st impulse - OPENS 1st impulse - OPENS (opening and closing) the gate (opening and The light will remain...
- Page 11 04. PROGRAMMING "P" 05. PROGRAMMING "E" DISTANCE PROGRAMMING SOFT START 02 (activates present man at the closing) The present man is active only in closing. distance PGM OFF distance PGM ON 01 (activates present man) This menu allows you to enable or disable The motor only works if you hold down the pushbutton LS or LO.
- Page 12 05. PROGRAMMING "E" 05. PROGRAMMING "E" SOFT START COURTESY LIGHT TIME 00 disabled function 01 enabled function This menu lets you set the time (1-99 minutes), that the courtesy This menu allows you to enable/disable soft start. light stays on after the closing of the gate. With soft start function enabled, at each motion beginning, the The E2 menu is only available if the courtesy light function is control board will manage the start of the motor, gradually...
- Page 13 05. PROGRAMMING "E" 05. PROGRAMAR "E" FOLLOW ME TRAVÃO ELECTRÓNICO E4 MENU DISABLE. E5 MENU DISABLE. 05. PROGRAMAR "E" DECELERATION SPEED 00 disabled function 01 enabled function This menu allows you to activate the option Follow me. With this function activated whenever the photocells detect the passage of a user/obstacle, the control board triggers the closing operation after 3 seconds.
- Page 14 05. PROGRAMMING "E" 05. PROGRAMMING "E" MANEUVER COUNTER RESET - RESTORE FACTORY VALUES This menu allows you to check how many complete maneuvers were performed by the control By doing reset, all factory settings will be restored and all saved commands will be deleted. board (complete maneuver it is understood by opening and closing).
- Page 15 05. PROGRAMMING "E" 06. DISPLAY RGB OUTPUT DISPLAY INDICATIONS MENU DESCRIPTION MENU DESCRIPTION Continuous light Flashing light Opening limit-switch enabled Inversion by effort (factory default 01) This menu allows you to select the functioning mode of the four signs, fixed or intermittent Closing limit-switch enabled Obstructed photocells output.
-
Page 16: Components Test
07. COMPONENTS TEST 07. COMPONENTS TEST TEST SCHEME INPUTS TEST To detect which components have problems during a sectional door installation, In the position corresponding to each transmitter input in low voltage, the control board has a LED to identify the condition of it. The LED on indicates that the input is closed, while the sometimes it's necessary to conduct tests with a direct connection to a 230V power LED off indicates that the input is open. -
Page 17: Troubleshooting
08. TROUBLESHOOTING INSTRUCTIONS FOR FINAL CONSUMERS/TECHNICIANS Anomaly Procedure Behavior Procedure II Discovering the origin of the problem • Motor • Make sure you have • Still not working. • Consult a qualified 1 • Open control box and check if 3 •... -
Page 18: Connection Scheme
09. CONNECTION SCHEME CONTROL BOARD CONNECTIONS...
Need help?
Do you have a question about the MC50SE and is the answer not in the manual?
Questions and answers