Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Motorline professional MC18
Summary of Contents for Motorline professional MC18
- Page 1 MC18 USER/INSTALLER MANUAL v3.0 REV. 01/2023...
-
Page 2: Table Of Contents
00. CONTENT 01. SAFETY INSTRUCTIONS INDEX WARNING: 01. SAFETY INSTRUCTIONS This product is certified in accordance with European 02. CONNECTION SCHEME Community (EC) safety standards. CONNECTION OF COMPONENTS TO THE CONTROL BOARD 03. THE CONTROL BOARD This product complies with Directive 2011/65/EU of the TECHNICAL CHARACTERISTICS European Parliament and of the Council, of 8 June 2011, on PRE-CONFIGURATION INDICATIONS... -
Page 3: Safety Instructions
01. SAFETY INSTRUCTIONS GENERAL WARNINGS • Children shouldn’t play with the product or opening devices to avoid the motorized door or gate from being triggered involuntarily. • This manual contains very important safety and usage information. Read all instructions carefully before beginning the installation/ WARNINGS FOR TECHNICIANS usage procedures and keep this manual in a safe place that it can be consulted whenever necessary. - Page 4 01. SAFETY INSTRUCTIONS RESPONSABILITY September 2009. • Attach the permanent label for the manual release as close as possible • Supplier disclaims any liability if: to the release mechanism. • Product failure or deformation result from improper installation • Disconnect means, such as a switch or circuit breaker on the electrical use or maintenance! panel, must be provided on the product’s fixed power supply leads in •...
-
Page 5: Connection Scheme
03. THE CONTROL BOARD CONNECTION OF COMPONENTS TO THE CONTROL BOARD TECHNICAL CHARACTERISTICS The MC18 is a 24V DC electronic control board, with a built-in radio control system, develo- ped for the automation of shutters. (CN3) • Output for motors 24Vdc 2 x 50 W max. -
Page 6: Pre-Configuration Indications 5A
03. THE CONTROL BOARD 03. THE CONTROL BOARD PRE-CONFIGURATION INDICATIONS OPERATIONAL CHARACTERISTICS : 01 • Antenna input (mass) Operation with remote control buttons: 02 • Antenna input (hot pole) • The open button will open until the factory set time expires. •... -
Page 7: Obstacles Detection
This is the main menu of the MC18 control board, where you have access to the most important NOTE: In the last 5 sec. of maneuver the reaction to the obstacles is simply to stop. - Page 8 04. PROGRAMMING MAIN MENU 04. PROGRAMMING MAIN MENU MAIN MENU MAIN MENU T. PAUSA | PROGRAMMING THE AUTOMATIC CLOSE TIME (4 MIN. MAXIMUM) T. MOT | PROGRAMMING THE WORKING TIME OF THE MOTORS (4 MIN. MAXIMUM) The control board allows automatic closing after a certain waiting time, up to a maximum of The control board is provided with a working time set to 30 seconds without slow-speed.
-
Page 9: Reset Factory Setting 8A
04. PROGRAMMING MAIN MENU 05. PROGRAMMING EXTENDED MENU 1 MAIN MENU EXTENDED MENU 1 T. R. CH | CLOSING DELAY PROGRAMMING (30 SEC. MAXIMUM) The control board is supplied by the manufacturer with an extended menu 1, which allows With this function, you can delay the start of closing of motor 1 by up to 30 seconds in rela- access to more functions of the control board. -
Page 10: Mot | Slow-Speed
05. PROGRAMMING EXTENDED MENU 1 06. PROGRAMMING EXTENDED MENU 2 EXTENDED MENU 1 EXTENDED MENU 2 T. MOT | The control board is provided by the manufacturer with an extended menu 2, which allows SLOW-SPEED access to more functions of the control board. With this function, you can activate/deactivate the slow-speed of the motors, both when ope- To access the options of the extended menu 2, follow the instructions below: ning and when closing. -
Page 11: T.mot | Automatic Programming
06. PROGRAMMING EXTENDED MENU 2 07. PROGRAMMING EXTENDED MENU 3 EXTENDED MENU 2 EXTENDED MENU 3 The control board is provided by the manufacturer with the Extended menu 3, which allows T.MOT | AUTOMATIC PROGRAMMING access to more functions of the control board. The control board makes it possible to automatically program the course without having to If you want to change the speed of the slow-speed power executed by the control board, give slow-speed and stop orders. -
Page 12: Troubleshooting
08. TROUBLESHOOTING INSTRUCTIONS FOR END CONSUMERS INSTRUCTIONS FOR SPECIALIZED TECHNICIANS Anomaly Procedure Behavior Procedure II Find the source of the problem • Motor does • Check that the • Still not working • Consult a qualified 1 • Remove the mechanism cover; MOTORLINE technician.
Need help?
Do you have a question about the MC18 and is the answer not in the manual?
Questions and answers