Safety Cut-Out; Cleaning The Filters - Morphy Richards CYCLONIC BAGLESS UPRIGHT VACUUM CLEANER Instructions Manual

73337 rev1 29/10/08
H
Ó
I
˘
J
K
U U K K H H e e l l p p l l i i n n e e 0 0 8 8 4 4 4 4 8 8 7 7 1 1 0 0 9 9 4 4 9 9
6 6
16:06 Page 6
7 Re-fit the central mesh filter.
8 Shake the pleated filter Ó to
remove all dust.
9 Re-fit pleated filter with lid into the
dust canister by lining up the two
arrows and turning the lid quarter-
of-a-turn clockwise to lock.
10 Re-fit dust canister into cleaner
and push to lock into position.
11 Re-fit the front cover.

SAFETY CUT-OUT

If the cleaner overheats, a motor
protection thermostat will
automatically switch the motor off.
If this happens, switch the
cleaner off, unplug from the
power supply and leave the
cleaner to cool for at least 60
minutes. Check the airways for
blockages, empty the dust
canister and clean the filters
before restarting.
CLEANING THE
FILTERS
To maintain suction, the
pleated filter Ó must be
shaken clean each time the
dust canister is emptied.
Failure to clean the filter will
reduce suction and could damage
the motor if used for a prolonged
period. This may invalidate the
guarantee. If the filters become
damaged, they must be replaced.
Pleated filter
Clean the pleated filter every time
the canister is emptied to
maintain high performance. To
thoroughly clean it, wash it
regularly.
To remove it from the dust
canister lid, turn the filter quarter-
of-a-turn anti-clockwise H. Wash
in warm water (no detergent) and
allow to air dry before refitting.
R R e e p p l l a a c c e e m m e e n n t t P P a a r r t t s s 0 0 8 8 4 4 4 4 8 8 7 7 3 3 0 0 7 7 1 1 5 5
Motor protection filter
I
The motor protection filter ˘ is
located underneath the dust
canister.
1 Remove the dust canister.
2 Lift out the filter and shake over a
dustbin.
The filter may also be washed in
water (no detergents). Allow the
filter to air dry. Ensure the filter is
thoroughly dry before refitting.
3 Replace the filter I.
Exhaust filter
J
The exhaust filter is located below
the dust canister compartment.
1 Remove the front cover ‹.
2 Remove the exhaust filter
pulling forward at the top and
lifting it away.
3 Take the filter out of the cage and
shake vigorously over a dustbin.
The filter may also be washed in
warm water. Do not use
detergents. The filter must be
completely dry before re-fitting.
Allow filters to air dry naturally.
Replace the filter and the front
4
cover.
Changing the belt
If the brush bar stops rotating, it is
likely that the drive belt has
snapped (usually because the
brush has been stalled). A spare
belt is supplied. Replacement
belts can also be obtained from
Morphy Richards by calling the
helpline number at the base of the
page.
Accessing the floor
nozzle
K
1 Disconnect the cleaner from the
mains supply.
2 Put the switch to the 'off' position.
3 Remove the front cover and the
dust canister.
I I r r e e l l a a n n d d H H e e l l p p l l i i n n e e 1 1 8 8 0 0 0 0 4 4 0 0 9 9 1 1 1 1 9 9
by
6