Page 1 Automation Panel 900 User's Manual Version: 2.22 (January 2022) Order no.: MAAP900-ENG...
Page 2: Publishing Information
Publishing information B&R Industrial Automation GmbH B&R Strasse 1 5142 Eggelsberg Austria Telephone: +43 7748 6586-0 Fax: +43 7748 6586-26 office@br-automation.com Disclaimer All information in this manual is current as of its creation. The contents of this manual are subject to change without notice.
Page 3: Table Of Contents
3.1.1 Important installation information......................114 3.1.2 Installation with clamping blocks......................114 3.2 Mounting orientation............................115 3.2.1 Mounting orientation 0°......................... 115 3.2.2 Mounting orientation 45°........................115 3.3 Spacing for air circulation........................... 116 3.4 Fastening cables............................117 Automation Panel 900 user's manual V2.22...
Page 4 3.6.3 Evaluating temperatures in non-Windows operating systems.............. 121 3.6.4 Evaluating the measurement results.....................121 3.7 Connection examples..........................122 3.7.1 Selecting display units...........................122 3.7.2 One Automation Panel 900 system via onboard DVI................123 3.7.2.1 Base system requirements......................123 3.7.2.2 Link modules............................ 123 3.7.2.3 Cables.............................. 123 3.7.2.4 Possible Automation Panel devices, resolutions and segment lengths...........124...
Page 5 6.4.1.1 5CADVI.0xxx-00..........................157 6.4.2 SDL cables............................160 6.4.2.1 5CASDL.0xxx-00..........................160 6.4.3 SDL cables with 45° connector......................163 6.4.3.1 5CASDL.0xxx-01..........................163 6.4.4 SDL flex cables............................. 166 6.4.4.1 5CASDL.0xxx-03..........................166 6.4.5 SDL flex cables with extender......................169 6.4.5.1 5CASDL.0xx0-13..........................169 Automation Panel 900 user's manual V2.22...
Page 6 7.2 Replacing the fluorescent tubes......................... 192 7.2.1 Procedure.............................. 192 7.2.1.1 General information..........................193 7.2.1.2 Procedure for 12.1" Automation Panels..................193 7.2.1.3 Procedure for 15" Automation Panels..................... 194 8 Environmentally friendly disposal...............196 8.1 Separation of materials..........................196 Automation Panel 900 user's manual V2.22...
Page 7 A.6.2 Compatibility details..........................204 A.6.2.1 Example............................204 A.6.2.2 5.7" devices............................. 204 A.6.2.3 10.4" devices........................... 205 A.6.2.4 12.1" devices........................... 207 A.6.2.5 15" devices............................207 A.6.2.6 17" devices............................208 A.6.2.7 19" devices............................209 A.6.2.8 21.3" devices........................... 209 Automation Panel 900 user's manual V2.22...
Page 8: General Information
Fig. 67 "5AP920.1706-01 - Temperature/Humidity diagram > Rev. D0" on page • Updated photos of 5CASDL.0x00-13 SDL cables with an extender. • Changed Fig. 127 "5CASDL.0xxx-03 - Pinout" on page 168. Deleted structure of 5CASDL.0xxx-03 SDL cables. Table 1: Manual history Automation Panel 900 user's manual V2.22...
Page 9 Fig. 108 "5AP951.1505-01 / 5AP981.1505-01 - Hardware numbers" on page 136. • Updated section 2.2.5 "Block diagrams" on page • Updated USB interface covers 5AC900.1200-01, 5AC900.1200-02 and 5AC900.1200-03. • Discontinued USB interface cover 5AC900.1200-00. Table 1: Manual history Automation Panel 900 user's manual V2.22...
Page 10 "Block diagrams" on page 2.22 January 2022 • Updated technical data of the panels in section "Individual components" on page 27 and section "Stan- dards and certifications" on page 148. Table 1: Manual history Automation Panel 900 user's manual V2.22...
Page 11: General Safety Guidelines
• A minimum distance of 10 cm from monitors or television sets must be maintained. • Measuring instruments and devices must be grounded. • Test probes of floating potential measuring instruments must be discharged briefly on suitable grounded surfaces before measurement. Automation Panel 900 user's manual V2.22...
Page 12: Individual Components
This can otherwise result in dust deposits that affect the functionality of the device, especially in systems with active cooling (fans), which may no longer ensure sufficient cooling. Automation Panel 900 user's manual V2.22...
Page 13: Programs, Viruses And Malicious Programs
The term "control systems" refers to all types of B&R products such as controllers (e.g. X20), HMI systems (e.g. Power Panel T30), process control systems (e.g. APROL) and supporting systems such as engineering workstations with Automation Studio. Automation Panel 900 user's manual V2.22...
Page 14: Organization Of Safety Notices
Up to 6 mm ±0.1 mm Over 6 to 30 mm ±0.2 mm Over 30 to 120 mm ±0.3 mm Over 120 to 400 mm ±0.5 mm Over 400 to 1000 mm ±0.8 mm Automation Panel 900 user's manual V2.22...
Page 15: Overview
RS232 extension cable for remote operation of a display unit with touch screen, 1.8 m 9A0014.05 RS232 extension cable for remote operation of a display unit with touch screen, 5 m 9A0014.10 RS232 extension cable for remote operation of a display unit with touch screen, 10 m Automation Panel 900 user's manual V2.22...
Page 16 5MMUSB.4096-01 USB 2.0 flash drive, 4096 MB, B&R USB cables 5CAUSB.0018-00 USB 2.0 connection cable type A - type B, 1.8 m 5CAUSB.0050-00 USB 2.0 connection cable type A - type B, 5 m Automation Panel 900 user's manual V2.22...
Page 17: Technical Data
PC systems. As a result, the transfer of image data is independent of the display unit. This allows future innovations in the area of transfer technology to be implemented using a new Automation Panel Link. Automation Panel 900 user's manual V2.22...
Page 18: Complete System
Each device has at least one USB interface on the front and back so that data can be easily exchanged with an industrial PC (e.g. using a UBS flash drive). On display front on back Figure 2: USB interfaces on the Automation Panel (front and back) Automation Panel 900 user's manual V2.22...
Page 19: Temperature Specifications
The following table lists the specifications for minimum and maximum ambient temperature for all available Au- tomation Panel 900 variants during operation in relation to mounting orientation (for specifications, see "Mounting orientation" on page 115). Automation Panel 900 without Rittal housing Automation Panel Link DVI receiver SDL receiver SDL transmitter...
Page 20: Minimum Ambient Temperature During Operation
Technical data 2.2.2.2 Minimum ambient temperature during operation The minimum ambient temperature during operation is 0°C. Automation Panel 900 user's manual V2.22...
Page 21: Humidity Specifications
Table 5: Overview of humidity specifications for individual components The specifications listed correspond to the relative humidity at an ambient temperature of 30°C. For more detailed information about specific temperature-dependent humidity values, see the technical data for the individual com- ponents. Automation Panel 900 user's manual V2.22...
Page 22: Power Consumption
Technical data 2.2.4 Power consumption Total consumption is made up of the consumption of the Automation Panel 900 device as well as the power used by Automation Panel Link insert card. The following table lists the typical consumption for each component. The sum of both equals the total consumption.
Page 23: Block Diagrams
Digital display 98-pin LVDS Connector Inverter Display LVDS Transmitter Touch Touch Controller Fuse RS232 USB A USB A Connector Connector DVI-D RS232 RS232 24 V Backlight Potentiometer Figure 4: AP900 block diagram with DVI Link Automation Panel 900 user's manual V2.22...
Page 24: Ap900 With Sdl Receiver - Block Diagram
2*USB Digital display 98-pin LVDS Connector Inverter Display Touch screen FPGA Touch screen Controller Fuse USB A USB A Connector Connector DVI-D DVI-D 24 V Figure 6: AP900 with SDL transceiver - Block diagram Automation Panel 900 user's manual V2.22...
Page 25: Ap900 With Sdl3 Receiver - Block Diagram
Digital display 98-pin LVDS Connector Inverter Display FPGA SDL3 FPGA Touch screen Touch screen Controller Magnetics Fuse USB A USB A Connector Connector RJ45 24 V Figure 7: AP900 with SDL3 receiver - Block diagram Automation Panel 900 user's manual V2.22...
Page 26: Serial Number Sticker
(after selecting the "Serial number" option) at the top of the website (www.br-automation.com). The search provides a detailed list of installed components. Serial number entered here e.g. 75170168448 Switching to the option "Serial number" Figure 9: Example of serial number search Automation Panel 900 user's manual V2.22...
Page 27: Individual Components
• Fan-free operation • Can be upgraded with Display Link cards or PPC300 Front-side USB interface Figure 10: 5AP920.1043-01 - Front view Back-side USB interface Automation Panel Link Insert slot Figure 11: 5AP920.1043-01 - Rear view Automation Panel 900 user's manual V2.22...
Page 28: Order Data
Optional accessories Panel PC 300 insert cards 5PC310.L800-00 Panel PC 300 insert card for the Automation Panel 900; 256 MB SDRAM; CompactFlash slot (Type I); 2x ETH 10/100; RS232; USB 2.0 (via integrated USB 2.0 interfaces on the Automation Panel); battery; 24 VDC (order screw clamp 0TB103.9 or cage clamp 0TB103.91 separately)
Page 29 Touch screen drivers for approved operating systems are available for download in the Downloads section of the B&R website (www.br-automation.com). USB devices can only be connected to the Automation Panel directly (without a hub). Depends on the transfer technology, transfer distance and Automation Panel Link plug-in card being used. Automation Panel 900 user's manual V2.22...
Page 30: Temperature Humidity Diagram
(any specified Transport mounting orientation) -80 -70 -60 -50 -40 -30 -20 -10 40 50 Temperature [°C] Figure 12: 5AP920.1043-01 - Temperature humidity diagram 2.3.1.1.1.5 Dimensions 20.2 11.5 44.2 Figure 13: 5AP920.1043-01 - Dimensions Automation Panel 900 user's manual V2.22...
Page 31 251.5 Cutout Cutout size 303 ±0.5 mm x 243 ±0.5 mm suitable for 5AP920.1043-01 5AP980.1043-01 Figure 14: 5AP920.1043-01 - Cutout installation For additional information regarding installation and mounting orientation, see "Commissioning" on page 114. Automation Panel 900 user's manual V2.22...
Page 32: General Information
Legend strips for keys for labeling as needed Front-side USB interface Figure 15: 5AP951.1043-01 - Front view Rear USB connection Automation Panel Link insert slot Figure 16: 5AP951.1043-01 - Rear view Automation Panel 900 user's manual V2.22...
Page 33 28 with LED (yellow) Soft keys 10 with LED (yellow) System keys Numeric keys, cursor block Service life >1,000,000 actuations at 1 ±0.3 N to 3 ±0.3 N actuating force Table 10: 5AP951.1043-01 - Technical data Automation Panel 900 user's manual V2.22...
Page 34 The specified value applies to the Automation Panel device with a connected Automation Panel Link plug-in card. The maximum ambient temperature is typically derated 1°C per 1000 meters starting at 500 m above sea level. Visual deviations in color and surface quality are possible due to process or batch conditions. Automation Panel 900 user's manual V2.22...
Page 35 (any specified Transport mounting orientation) -80 -70 -60 -50 -40 -30 -20 -10 40 50 Temperature [°C] Figure 17: 5AP951.1043-01 - Temperature humidity diagram 2.3.1.1.2.5 Dimensions 20.2 11.5 44.2 Figure 18: 5AP951.1043-01 - Dimensions Automation Panel 900 user's manual V2.22...
Page 36 349.5 Cutout Cutout size 303 ±0.5 mm x 341 ±0.5 mm suitable for 5AP951.1043-01 5AP981.1043-01 Figure 19: 5AP951.1043-01 - Cutout installation For additional information regarding installation and mounting orientation, see "Commissioning" on page 114. Automation Panel 900 user's manual V2.22...
Page 37 24 VDC (order screw clamp ter- minal block 0TB103.9 or cage clamp terminal block 0TB103.91 separately). Optional accessories Accessories 5AC900.104X-04 Legend Strips Template 10,4" Automation Panel 5AP952.1043-01 and 5AP982.1043-01; for 1 device. Table 11: 5AP952.1043-01 - Order data Automation Panel 900 user's manual V2.22...
Page 38 2 to 8 Hz: 7.5 mm amplitude / 8 to 200 Hz: 2 g / 200 to 500 Hz: 4 g Transport 2 to 8 Hz: 7.5 mm amplitude / 8 to 200 Hz: 2 g / 200 to 500 Hz: 4 g Table 12: 5AP952.1043-01 - Technical data Automation Panel 900 user's manual V2.22...
Page 39 Visual deviations in color and surface quality are possible due to process or batch conditions. 2.3.1.1.3.4 Temperature humidity diagram Operation Storage (any specified Transport mounting orientation) -80 -70 -60 -50 -40 -30 -20 -10 40 50 Temperature [°C] Figure 22: 5AP952.1043-01 - Temperature humidity diagram Automation Panel 900 user's manual V2.22...
Page 40 Technical data 2.3.1.1.3.5 Dimensions 20.2 44.2 11.5 Figure 23: 5AP952.1043-01 - Dimensions Automation Panel 900 user's manual V2.22...
Page 41 279.5 Cutout Cutout size 402 ±0.5 mm x 271 ±0.5 mm suitable for 5AP952.1043-01 5AP982.1043-01 Figure 24: 5AP952.1043-01 - Cutout installation For additional information regarding installation and mounting orientation, see "Commissioning" on page 114. Automation Panel 900 user's manual V2.22...
Page 42 Front-side USB interface Legend strips for keys for labeling as needed Figure 25: 5AP980.1043-01 - Front view Back-side USB interface Automation Panel Link Insert slot Figure 26: 5AP980.1043-01 - Rear view Automation Panel 900 user's manual V2.22...
Page 43 5AP980.1043-01; for 3 devices. Panel PC 300 insert cards 5PC310.L800-00 Panel PC 300 insert card for the Automation Panel 900; 256 MB SDRAM; CompactFlash slot (Type I); 2x ETH 10/100; RS232; USB 2.0 (via integrated USB 2.0 interfaces on the Automation Panel);...
Page 44 Similar to Pantone 427CV Dark border color around display Similar to Pantone 432CV Color slide-in labels Similar to Pantone 429CV Gasket Flat gasket around display front Table 14: 5AP980.1043-01, 5AP980.1043-01, 5AP980.1043-01, 5AP980.1043-01 - Technical data Automation Panel 900 user's manual V2.22...
Page 45 (any specified Transport mounting orientation) -80 -70 -60 -50 -40 -30 -20 -10 40 50 Temperature [°C] Figure 27: 5AP980.1043-01 - Temperature humidity diagram 2.3.1.1.4.5 Dimensions 20.2 11.5 44.2 Figure 28: 5AP980.1043-01 - Dimensions Automation Panel 900 user's manual V2.22...
Page 46 251.5 Cutout Cutout size 303 ±0.5 mm x 243 ±0.5 mm suitable for 5AP920.1043-01 5AP980.1043-01 Figure 29: 5AP980.1043-01 - Cutout installation For additional information regarding installation and mounting orientation, see "Commissioning" on page 114. Automation Panel 900 user's manual V2.22...
Page 47 Legend strips for keys for labeling as needed Front-side USB interface Figure 30: 5AP981.1043-01 - Front view Rear USB connection Automation Panel Link insert slot Figure 31: 5AP981.1043-01 - Rear view Automation Panel 900 user's manual V2.22...
Page 48 5AP951.1043-01 and 5AP981.1043-01; for 1 device. Panel PC 300 insert cards 5PC310.L800-00 Panel PC 300 insert card for the Automation Panel 900; 256 MB SDRAM; CompactFlash slot (Type I); 2x ETH 10/100; RS232; USB 2.0 (via integrated USB 2.0 interfaces on the Automation Panel);...
Page 49 Dark gray keys color Similar to Pantone 431CV Orange keys color Similar to Pantone 151CV Color slide-in labels Similar to Pantone 429CV Gasket Flat gasket around display front Table 16: 5AP981.1043-01, 5AP981.1043-01, 5AP981.1043-01, 5AP981.1043-01 - Technical data Automation Panel 900 user's manual V2.22...
Page 50 Visual deviations in color and surface quality are possible due to process or batch conditions. 2.3.1.1.5.4 Temperature humidity diagram Operation Storage (any specified Transport mounting orientation) -80 -70 -60 -50 -40 -30 -20 -10 40 50 Temperature [°C] Figure 32: 5AP981.1043-01 - Temperature humidity diagram Automation Panel 900 user's manual V2.22...
Page 51 Technical data 2.3.1.1.5.5 Dimensions 20.2 11.5 44.2 Figure 33: 5AP981.1043-01 - Dimensions Automation Panel 900 user's manual V2.22...
Page 52 349.5 Cutout Cutout size 303 ±0.5 mm x 341 ±0.5 mm suitable for 5AP951.1043-01 5AP981.1043-01 Figure 34: 5AP981.1043-01 - Cutout installation For additional information regarding installation and mounting orientation, see "Commissioning" on page 114. Automation Panel 900 user's manual V2.22...
Page 53 Legend strips for keys Front-side USB interface for labeling as needed Figure 35: 5AP982.1043-01 - Front view Rear USB connection Automation Panel Link insert slot Figure 36: 5AP982.1043-01 - Rear view Automation Panel 900 user's manual V2.22...
Page 54 5AP952.1043-01 and 5AP982.1043-01; for 1 device. Panel PC 300 insert cards 5PC310.L800-00 Panel PC 300 insert card for the Automation Panel 900; 256 MB SDRAM; CompactFlash slot (Type I); 2x ETH 10/100; RS232; USB 2.0 (via integrated USB 2.0 interfaces on the Automation Panel);...
Page 55 Dark gray keys color Similar to Pantone 431CV Orange keys color Similar to Pantone 151CV Color slide-in labels Similar to Pantone 429CV Gasket Flat gasket around display front Table 18: 5AP982.1043-01, 5AP982.1043-01, 5AP982.1043-01, 5AP982.1043-01 - Technical data Automation Panel 900 user's manual V2.22...
Page 56 (any specified Transport mounting orientation) -80 -70 -60 -50 -40 -30 -20 -10 40 50 Temperature [°C] Figure 37: 5AP982.1043-01 - Temperature humidity diagram 2.3.1.1.6.5 Dimensions 20.2 44.2 11.5 Figure 38: 5AP982.1043-01 - Dimensions Automation Panel 900 user's manual V2.22...
Page 57 279.5 Cutout Cutout size 402 ±0.5 mm x 271 ±0.5 mm suitable for 5AP952.1043-01 5AP982.1043-01 Figure 39: 5AP982.1043-01 - Cutout installation For additional information regarding installation and mounting orientation, see "Commissioning" on page 114. Automation Panel 900 user's manual V2.22...
Page 58: Automation Panel 12.1" Svga
• Fan-free operation • Can be upgraded with Display Link cards or PPC300 Front-side USB interface Figure 40: 5AP920.1214-01 - Front view Back-side USB interfaces Automation Panel Link Insert slot Figure 41: 5AP920.1214-01 - Rear view Automation Panel 900 user's manual V2.22...
Page 59 Optional accessories Panel PC 300 insert cards 5PC310.L800-00 Panel PC 300 insert card for the Automation Panel 900; 256 MB SDRAM; CompactFlash slot (Type I); 2x ETH 10/100; RS232; USB 2.0 (via integrated USB 2.0 interfaces on the Automation Panel); battery; 24 VDC (order screw clamp 0TB103.9 or cage clamp 0TB103.91 separately)
Page 60 Touch screen drivers for approved operating systems are available for download in the Downloads section of the B&R website (www.br-automation.com). USB devices can only be connected to the Automation Panel directly (without a hub). Depends on the transfer technology, transfer distance and Automation Panel Link plug-in card being used. Automation Panel 900 user's manual V2.22...
Page 61 (any specified Transport mounting orientation) -80 -70 -60 -50 -40 -30 -20 -10 40 50 Temperature [°C] Figure 42: 5AP920.1214-01 - Temperature humidity diagram 2.3.1.2.1.5 Dimensions 18.2 42.2 11.5 Figure 43: 5AP920.1214-01 - Dimensions Automation Panel 900 user's manual V2.22...
Page 62 Outer contour (Automation Panel) 275.5 Cutout Cutout size 342 ±0.5 mm x 267 ±0.5 mm suitable for 5AP920.1214-01 Figure 44: 5AP920.1214-01 - Cutout installation For additional information regarding installation and mounting orientation, see "Commissioning" on page 114. Automation Panel 900 user's manual V2.22...
Page 63: Automation Panel 15" Xga
• Fan-free operation • Can be upgraded with Display Link cards or PPC300 Front-side USB interface Figure 45: 5AP920.1505-01 - Front view Back-side USB interfaces Automation Panel Link Insert slot Figure 46: 5AP920.1505-01 - Rear view Automation Panel 900 user's manual V2.22...
Page 64 Optional accessories Panel PC 300 insert cards 5PC310.L800-00 Panel PC 300 insert card for the Automation Panel 900; 256 MB SDRAM; CompactFlash slot (Type I); 2x ETH 10/100; RS232; USB 2.0 (via integrated USB 2.0 interfaces on the Automation Panel); battery; 24 VDC (order screw clamp 0TB103.9 or cage clamp 0TB103.91 separately)
Page 65 Panel overlay Material Polyester Light background color Similar to Pantone 427CV Dark border color around display Similar to Pantone 432CV Gasket Flat gasket around display front Table 22: 5AP920.1505-01, 5AP920.1505-01, 5AP920.1505-01 - Technical data Automation Panel 900 user's manual V2.22...
Page 66 Mounting orientation 0° or -45 -80 -70 -60 -50 -40 -30 -20 -10 40 50 Temperature [°C] Figure 47: 5AP920.1505-01 - Temperature humidity diagram 2.3.1.3.1.5 Dimensions 18.7 42.7 11.5 26.5 Figure 48: 5AP920.1505-01 - Dimensions Automation Panel 900 user's manual V2.22...
Page 67 Outer contour (Automation Panel) Cutout Cutout size 415 ±0.5 mm x 312 ±0.5 mm suitable for 5AP920.1505-01 5AP980.1505-01 Figure 49: 5AP920.1505-01 - Cutout installation For additional information regarding installation and mounting orientation, see "Commissioning" on page 114. Automation Panel 900 user's manual V2.22...
Page 68 Legend strips for keys for labeling as needed Front-side USB interface Figure 50: 5AP951.1505-01 - Front view Rear USB connections Automation Panel Link insert slot Figure 51: 5AP951.1505-01 - Rear view Automation Panel 900 user's manual V2.22...
Page 69 Soft keys 12 with LED (yellow) System keys Alphanumeric keys, numeric keys, cursor block Service life >1,000,000 actuations at 1 ±0.3 N to 3 ±0.3 N actuating force Table 24: 5AP951.1505-01 - Technical data Automation Panel 900 user's manual V2.22...
Page 70 The specified value applies to the Automation Panel device with a connected Automation Panel Link plug-in card. The maximum ambient temperature is typically derated 1°C per 1000 meters starting at 500 m above sea level. Visual deviations in color and surface quality are possible due to process or batch conditions. Automation Panel 900 user's manual V2.22...
Page 71 Mounting orientation 0° or -45 -80 -70 -60 -50 -40 -30 -20 -10 40 50 Temperature [°C] Figure 52: 5AP951.1505-01 - Temperature humidity diagram 2.3.1.3.2.5 Dimensions 18.2 11.5 26.5 42.2 Figure 53: 5AP951.1505-01 - Dimensions Automation Panel 900 user's manual V2.22...
Page 72 Outer contour (Automation Panel) Cutout Cutout size 415 ±0.5 mm x 412 ±0.5 mm suitable for 5AP951.1505-01 5AP981.1505-01 Figure 54: 5AP951.1505-01 - Cutout installation For additional information regarding installation and mounting orientation, see "Commissioning" on page 114. Automation Panel 900 user's manual V2.22...
Page 73 Front-side USB interface Legend strips for keys for labeling as needed Figure 55: 5AP920.1505-01 - Front view Back-side USB interfaces Automation Panel Link Insert slot Figure 56: 5AP980.1505-01 - Rear view Automation Panel 900 user's manual V2.22...
Page 74 Panel PC 5PC781.1505-00; for 4 devices. Panel PC 300 insert cards 5PC310.L800-00 Panel PC 300 insert card for the Automation Panel 900; 256 MB SDRAM; CompactFlash slot (Type I); 2x ETH 10/100; RS232; USB 2.0 (via integrated USB 2.0 interfaces on the Automation Panel);...
Page 75 Similar to Pantone 427CV Dark border color around display Similar to Pantone 432CV Color slide-in labels Similar to Pantone 429CV Gasket Flat gasket around display front Table 26: 5AP980.1505-01, 5AP980.1505-01, 5AP980.1505-01 - Technical data Automation Panel 900 user's manual V2.22...
Page 76 Mounting orientation 0° or -45 -80 -70 -60 -50 -40 -30 -20 -10 40 50 Temperature [°C] Figure 57: 5AP980.1505-01 - Temperature humidity diagram 2.3.1.3.3.5 Dimensions 18.2 26.5 11.5 42.2 Figure 58: 5AP980.1505-01 - Dimensions Automation Panel 900 user's manual V2.22...
Page 77 Outer contour (Automation Panel) Cutout Cutout size 415 ±0.5 mm x 312 ±0.5 mm suitable for 5AP920.1505-01 5AP980.1505-01 Figure 59: 5AP980.1505-01 - Cutout installation For additional information regarding installation and mounting orientation, see "Commissioning" on page 114. Automation Panel 900 user's manual V2.22...
Page 78 Legend strips for keys for labeling as needed Front-side USB interface Figure 60: 5AP981.1505-01 - Front view Rear USB connections Automation Panel Link insert slot Figure 61: 5AP981.1505-01 - Rear view Automation Panel 900 user's manual V2.22...
Page 79 Panel PC 5PC781.1505-00; for 4 devices. Panel PC 300 insert cards 5PC310.L800-00 Panel PC 300 insert card for the Automation Panel 900; 256 MB SDRAM; CompactFlash slot (Type I); 2x ETH 10/100; RS232; USB 2.0 (via integrated USB 2.0 interfaces on the Automation Panel);...
Page 80 Dark gray keys color Similar to Pantone 431CV Orange keys color Similar to Pantone 151CV Color slide-in labels Similar to Pantone 429CV Gasket Flat gasket around display front Table 28: 5AP981.1505-01, 5AP981.1505-01, 5AP981.1505-01 - Technical data Automation Panel 900 user's manual V2.22...
Page 81 Visual deviations in color and surface quality are possible due to process or batch conditions. 2.3.1.3.4.4 Temperature humidity diagram Operation Mounting orientation 0° or -45 -80 -70 -60 -50 -40 -30 -20 -10 40 50 Temperature [°C] Figure 62: 5AP981.1505-01 - Temperature humidity diagram Automation Panel 900 user's manual V2.22...
Page 82 Technical data 2.3.1.3.4.5 Dimensions 18.2 11.5 26.5 42.2 Figure 63: 5AP981.1505-01 - Dimensions Automation Panel 900 user's manual V2.22...
Page 83 Outer contour (Automation Panel) Cutout Cutout size 415 ±0.5 mm x 412 ±0.5 mm suitable for 5AP951.1505-01 5AP981.1505-01 Figure 64: 5AP981.1505-01 - Cutout installation For additional information regarding installation and mounting orientation, see "Commissioning" on page 114. Automation Panel 900 user's manual V2.22...
Page 84: Automation Panel 17" Sxga
• Fan-free operation • Can be upgraded with Display Link cards or PPC300 Front-side USB interface Figure 65: 5AP920.1706-01 - Front view Back-side USB interfaces Automation Panel Link Insert slot Figure 66: 5AP920.1706-01 - Rear view Automation Panel 900 user's manual V2.22...
Page 85 Optional accessories Panel PC 300 insert cards 5PC310.L800-00 Panel PC 300 insert card for the Automation Panel 900; 256 MB SDRAM; CompactFlash slot (Type I); 2x ETH 10/100; RS232; USB 2.0 (via integrated USB 2.0 interfaces on the Automation Panel); battery; 24 VDC (order screw clamp 0TB103.9 or cage clamp 0TB103.91 separately)
Page 86 Derating the maximum ambient temperature - typically 1°C per 1000 meters (from 500 meters above sea level). Depending on the process or batch, there may be visible deviations in the color and surface structure. Automation Panel 900 user's manual V2.22...
Page 87 Temperature [°C] Figure 67: 5AP920.1706-01 - Temperature/Humidity diagram > Rev. D0 Operation Mounting orientation 0° -80 -70 -60 -50 -40 -30 -20 -10 Temperature [°C] Figure 68: 5AP920.1706-01 - Temperature/Humidity diagram < Rev. C0 Automation Panel 900 user's manual V2.22...
Page 88 Technical data 2.3.1.4.1.5 Dimensions 23.2 420.5 47.2 Figure 69: 5AP920.1706-01 - Dimensions Automation Panel 900 user's manual V2.22...
Page 89 381.5 Cutout Cutout size 460 ±0.5 mm x 373 ±0.5 mm suitable for 5AP920.1706-01 468.5 Figure 70: 5AP920.1706-01 - Cutout installation For additional information regarding installation and mounting orientation, see "Commissioning" on page 114. Automation Panel 900 user's manual V2.22...
Page 90: Automation Panel 19" Sxga
• Fan-free operation • Can be upgraded with Display Link cards or PPC300 Front-side USB interface Figure 71: 5AP920.1906-01 - Front view Back-side USB interfaces Automation Panel Link Insert slot Figure 72: 5AP920.1906-01 - Rear view Automation Panel 900 user's manual V2.22...
Page 91 Optional accessories Panel PC 300 insert cards 5PC310.L800-00 Panel PC 300 insert card for the Automation Panel 900; 256 MB SDRAM; CompactFlash slot (Type I); 2x ETH 10/100; RS232; USB 2.0 (via integrated USB 2.0 interfaces on the Automation Panel); battery; 24 VDC (order screw clamp 0TB103.9 or cage clamp 0TB103.91 separately)
Page 92 Touch screen drivers for approved operating systems are available for download in the Downloads section of the B&R website (www.br-automation.com). USB devices can only be connected to the Automation Panel directly (without a hub). Depends on the transfer technology, transfer distance and Automation Panel Link plug-in card being used. Automation Panel 900 user's manual V2.22...
Page 93 -80 -70 -60 -50 -40 -30 -20 -10 40 50 Temperature [°C] Figure 73: 5AP920.1906-01 - Temperature/Humidity diagram > Rev. D0 -80 -70 -60 -50 -40 -30 -20 -10 Temperature [°C] Figure 74: 5AP920.1906-01 - Temperature/Humidity diagram < Rev. C0 Automation Panel 900 user's manual V2.22...
Page 94 Technical data 2.3.1.5.1.5 Dimensions 26.7 50.7 472.5 27.5 Figure 75: 5AP920.1906-01 - Dimensions Automation Panel 900 user's manual V2.22...
Page 95 412.5 Cutout Cutout size 510 ±0.5 mm x 404 ±0.5 mm suitable for 5AP920.1906-01 518.5 Figure 76: 5AP920.1906-01 - Cutout installation For additional information regarding installation and mounting orientation, see "Commissioning" on page 114. Automation Panel 900 user's manual V2.22...
Page 96: Automation Panel 21.3" Uxga
SDL Out, transfer of display data, touch screen, USB 1.1, matrix keys and, service data, 24 VDC (order screw clamp ter- minal block 0TB103.9 or cage clamp terminal block 0TB103.91 separately). Table 33: 5AP920.2138-01 - Order data Automation Panel 900 user's manual V2.22...
Page 97 2 to 8 Hz: 7.5 mm amplitude / 8 to 200 Hz: 2 g / 200 to 500 Hz: 4 g Shock Operation 15 g, 11 ms Storage 30 g, 15 ms Transport 30 g, 15 ms Elevation Operation Max. 3000 m Table 34: 5AP920.2138-01 - Technical data Automation Panel 900 user's manual V2.22...
Page 98 Visual deviations in color and surface quality are possible due to process or batch conditions. 2.3.1.6.1.4 Temperature humidity diagram Operation Mounting orientation 0° or -45 -80 -70 -60 -50 -40 -30 -20 -10 40 50 Temperature [°C] Figure 79: 5AP920.2138-01 - Temperature humidity diagram Automation Panel 900 user's manual V2.22...
Page 99 Technical data 2.3.1.6.1.5 Dimensions 29.2 27.1 528.8 53.2 Figure 80: 5AP920.2138-01 - Dimensions Automation Panel 900 user's manual V2.22...
Page 100 455.5 Cutout Cutout size 566 ±0.5 mm x 447 ±0.5 mm suitable for 5AP920.2138-01 574.5 Figure 81: 5AP920.2138-01 - Cutout installation For additional information regarding installation and mounting orientation, see "Commissioning" on page 114. Automation Panel 900 user's manual V2.22...
Page 101: Automation Panel Link Plug-In Cards
B&R Industrial PC (e.g. Automation PC 810) via the cable. A plug-in card is simply inserted into the Automation Panel 900 slot provided and fastened into place using the two locating screws (max. tightening torque 0.5 Nm).
Page 102: 5Dldvi.1000-01
This type of transfer supports the transmission of display data, USB 2.0 data and touch screen data over separate cables for each. • Can be used in all Automation Panel 900 devices • DVI-D, RS232 and USB 2.0 connections 2.3.2.1.2 Order data...
Page 103 USB Type B connector Figure 84: Comparison of USB Type A/B connectors If the Display Link is connected correctly, then the Automation Panel 900 is equipped with one or more (depending on the type) USB ports (front and back). Information: USB 2.0 is supported for cables up to 5 meters in length.
Page 104 Technical data 2.3.2.1.4.4 COM Serial interface The RS232 interface is used to transfer signals from the Automation Panel 900 touch screen. B&R offers RS232 cables up to 10 meters in length (see "Cables" on page 157). COM serial interface RS232...
Page 105: 5Dlsdl.1000-00
1.1 is fully integrated in SDL and transferred over this distance as well without the need for external modules. A panel can be operated on a line using an SDL receiver. • Can be used in all Automation Panel 900 devices • SDL IN connections 2.3.2.2.2 Order data...
Page 106 2.3.2.2.4.3 Panel IN This interface is intended for the SDL connection to a B&R Industrial PC. The necessary SDL cables are available separately from B&R (see "Cables" on page 157). Automation Panel 900 user's manual V2.22...
Page 107: 5Dlsdl.1000-01
To achieve the maximum segment length, it is possible to use cables with an integrated extender that acts as an amplifier. Additional hardware is not required. • Can be used in all Automation Panel 900 devices • SDL IN and SDL OUT connections 2.3.2.3.2 Order data...
Page 108 B&R (see "Cables" on page 157). 2.3.2.3.4.4 Panel OUT This interface is intended for the SDL connection to an additional Automation Panel 900 device. The necessary SDL cables are available separately from B&R (see "Cables" on page 157).
Page 109: 5Dlsd3.1000-00
✓ SDL3 interface USB1, USB2 USB 2.0 Power supply Grounding Maximum cable length for SDL3: 100 m Requirements • Automation Panel with SDL3 receiver • B&R industrial PC with SDL3 interface • SDL3/SDL4 cable Automation Panel 900 user's manual V2.22...
Page 110 The specified value refers to an Automation Panel Link plug-in card connected in a 19" Automation Panel device. 2.3.2.4.4 Interfaces 2.3.2.4.4.1 SDL3 In interface The "SDL3 In" interface is a female RJ45 connector and operated with SDL3 transmission technology. For addi- tional information, see section "SDL3 operation" on page 109. Automation Panel 900 user's manual V2.22...
Page 111 The male panel connector is specified for 500 connection cycles. Information: If a display device with a touch screen is connected to the panel interface and then disconnected again during operation (hot-plugging), it may be necessary to recalibrate the touch screen. Automation Panel 900 user's manual V2.22...
Page 112 The interfaces, etc. available on the device or module have been numbered as such for easy identification. This numbering may differ from that used by the particular operating system. Each USB interface is protected by a maintenance-free "USB current-limiting circuit breaker" (total max. 500 mA). Automation Panel 900 user's manual V2.22...
Page 113 • 5AP982.1043-01 ≤ Rev. E0 • 5AP920.1214-01 ≤ Rev. D0 • 5AP951.1505-01 • 5AP920.1505-01 ≤ Rev. H0 • 5AP980.1505-01 ≤ Rev. G0 • 5AP981.1505-01 ≤ Rev. I0 • 5AP920.1706-01 • 5AP920.1906-01 ≤ Rev. L0 • 5AP920.2138-01 Automation Panel 900 user's manual V2.22...
Page 114: Commissioning
A hex key (3 mm) is needed to tighten and loosen the screws. The maximum torque when tightening the clamp is 0.5 Nm. Devices must be installed on flat, clean and burr-free surface; uneven areas can cause damage to the display when the screws are tightened or intrusion of dust and water. Automation Panel 900 user's manual V2.22...
Page 115: Mounting Orientation
Commissioning 3.2 Mounting orientation The following diagrams show the approved mounting orientations for the Automation Panel 900. 3.2.1 Mounting orientation 0° Side with connections facing down! Figure 88: Mounting orientation 0° 3.2.2 Mounting orientation 45° Side with connections facing down! Side with connections facing down! Figure 89: Mounting orientations -45°...
Page 116: Spacing For Air Circulation
Air inlet Figure 90: Spacing for air circulation - Side view At least At least 10 mm spacing 10 mm spacing Side with connections facing down! Figure 91: Spacing for air circulation - Rear view Automation Panel 900 user's manual V2.22...
Page 117: Fastening Cables
This grounding clip (functional ground) must be connected to a central grounding point on the control cabinet using a 6.3 mm tab connector and the shortest possible path with the least resistance possible (e.g. copper strip, at least 2.5 mm²). Figure 93: Functional grounding clip Automation Panel 900 user's manual V2.22...
Page 118: General Instructions For The Temperature Test Procedure
(www.br-automation.com). The B&R Control Center uses the B&R Automation Device Interface (ADI). A separate application can be developed if it is necessary to collect historical data. Information: Software development kits such as the ADI .NET SDK are available on the B&R website (www.br-au- tomation.com). Automation Panel 900 user's manual V2.22...
Page 119: Evaluating With The Burnintest Tool From Passmark
Loopback plugs are also available from Passmark. More information is available at www.pass- mark.com. The following screenshots are based on Passmark BurnInTest Pro V4 and a 2-slot APC810 with DVD. Figure 94: Settings for Passmark BurnInTest Pro V4 and a 2-slot APC810 with DVD Automation Panel 900 user's manual V2.22...
Page 120 Windows. The test USB must then be deselected, and the USB flash drives must be configured as the testing device in the disk properties. Information: Serial loopback plugs are relatively easy to create. Simply connect several pins on the serial interface with wires. Automation Panel 900 user's manual V2.22...
Page 121: Evaluating Temperatures In Non-Windows Operating Systems
76°C Board I/O 51°C 66°C 76°C Board ETH2 52°C 67°C 77°C Board power supply 51°C 66°C 76°C ETH2 65°C 80°C 90°C Power supply 51°C 66°C 76°C Table 51: Evaluation example using a 2-slot APC810 Automation Panel 900 user's manual V2.22...
Page 122: Connection Examples
3.7.1 Selecting display units In order to connect an Automation Panel 800 and an Automation Panel 900 on the same line, the devices must have the same display type. The following table lists the AP900 devices that can be connected on the same line with an AP800 device.
Page 123: One Automation Panel 900 System Via Onboard Dvi
A separate cable is used for both the touch screen and USB data. If USB devices are to be operated on the Automation Panel 900, the maximum distance is 5 meters. USB devices can only be connected directly to the Automation Panel (i.e.
Page 124: Possible Automation Panel Devices, Resolutions And Segment Lengths
5 m / 10 m Table 55: Possible Automation Panel devices, resolutions and segment lengths USB support is not possible on the Automation Panel 900 in these cases since USB is limited to 5 m. Information: When transferring data via DVI, it is not possible to read statistical values from Automation Panel 900 devices.
Page 125: One Automation Panel 900 System Via Onboard Sdl
3.7.3 One Automation Panel 900 system via onboard SDL An Automation Panel 900 is connected to the integrated SDL interface (onboard) via an SDL cable. USB devices can only be connected directly to the Automation Panel (i.e. without a hub).
Page 126: Settings In Bios
For detailed information, see the user's manual for the B&R Industrial PC being used. Touch screen functionality COM C must be enabled in BIOS in order to operate the panel touch screen connected to the monitor/panel interface ("Advanced - Baseboard/Panel features - Legacy devices"). Automation Panel 900 user's manual V2.22...
Page 127: Four Automation Panel 900 Systems Via Onboard Sdl
3.7.4 Four Automation Panel 900 systems via onboard SDL An Automation Panel 900 is connected to the integrated SDL interface (onboard) via an SDL cable. Up to three other Automation Panels of the same type are connected to this Automation Panel and operated via SDL. All four of the panels show the same content (display clone).
Page 128: Settings In Bios
For detailed information, see the user's manual for the B&R Industrial PC being used. Touch screen functionality COM C must be enabled in BIOS in order to operate the panel touch screen connected to the monitor/panel interface ("Advanced - Baseboard/Panel features - Legacy devices"). Automation Panel 900 user's manual V2.22...
Page 129: One Automation Panel 900 Via Sdl3
Commissioning 3.7.5 One Automation Panel 900 via SDL3 One Automation Panel 900 is connected to the optional SDL3 interface via an SDL3 cable. USB devices can only be connected directly to the Automation Panel (i.e. without a hub). Monitor/Panel Option SDL3 segment Max.
Page 130 For detailed information, see the user's manual for the B&R Industrial PC being used. Touch screen functionality COM C must be enabled in BIOS in order to operate the panel touch screen connected to the monitor/panel interface ("Advanced - Baseboard/Panel features - Legacy devices"). Automation Panel 900 user's manual V2.22...
Page 131: Connecting Peripheral Usb Devices
Many different peripheral USB devices can be connected to the 2 or 3 USB interfaces on the Automation Panel 900. These can each handle a load of 500 mA. The maximum transfer rate is USB 2.0. Information: Only end devices (not hubs) can be connected to the Automation Panel 900. USB 2.0 USB 2.0...
Page 132: Remote Connection To Automation Panel 800 / 900 Via Sdl
3.8.2 Remote connection to Automation Panel 800 / 900 via SDL Many different peripheral USB devices can be connected to the 2 or 3 USB interfaces on Automation Panel 900 or the USB interfaces on Automation Panel 800 devices. These can each handle a load of 500 mA. The maximum transfer rate is USB 1.1.
Page 133: Remote Connection To Automation Panel 900 Via Sdl3
Many different peripheral USB devices can be connected to the 2 or 3 USB interfaces on the Automation Panel 900. These can each handle a load of 500 mA. The maximum transfer rate is USB 2.0. Information: Only end devices (not hubs) can be connected to the Automation Panel 900. SDL3 (USB 2.0) USB 2.0 USB memory media e.g.
Page 134: Key And Led Configurations
The images below show the positions of keys and LEDs in the matrix. This information is indicated as follows. Hardware number of LED Hardware number of key Hardware number of LED Hardware number of key Key without LED Key with LED Figure 104: Keys and LEDs in the matrix Automation Panel 900 user's manual V2.22...
Page 135: Automation Panel 10.4" Vga
Commissioning 3.9.1 Automation Panel 10.4" VGA 3.9.1.1 Automation Panel 5AP951.1043-01 / 5AP981.1043-01 Figure 105: 5AP951.1043-01 / 5AP981.1043-01 - Hardware numbers 3.9.1.2 Automation Panel 5AP952.1043-01 / 5AP982.1043-01 Figure 106: 5AP952.1043-01 / 5AP982.1043-01 - Hardware numbers Automation Panel 900 user's manual V2.22...
Page 136: Automation Panel 5Ap980.1043-01
Commissioning 3.9.1.3 Automation Panel 5AP980.1043-01 Figure 107: 5AP980.1043-01 - Hardware numbers 3.9.2 Automation Panel 15" XGA 3.9.2.1 Automation Panel 5AP951.1505-01 / 5AP981.1505-01 Figure 108: 5AP951.1505-01 / 5AP981.1505-01 - Hardware numbers Automation Panel 900 user's manual V2.22...
Page 137: Automation Panel 5Ap980.1505-01
Commissioning 3.9.2.2 Automation Panel 5AP980.1505-01 Figure 109: 5AP980.1505-01 - Hardware numbers Automation Panel 900 user's manual V2.22...
Page 138: Touch Screen Calibration
On all other devices, the touch screen driver must be subsequently installed to operate the touch screen. The appropriate driver is available for download in the Downloads section of the B&R website (www.br-automation.com). Automation Panel 900 user's manual V2.22...
Page 139: Automation Runtime / Visual Components
• Use complementary colors for subsequent images. • Use screensavers. 3.12 Pixel errors Information: Displays can contain faulty pixels (pixel errors) due to the manufacturing process. They are not grounds for initiating a complaint or warranty claim. Automation Panel 900 user's manual V2.22...
Page 140: Software
• Reading temperatures, fan speeds, statistical data and switch settings • Reading operating hours (power-on hours) • Reading user and factory settings • Reading software versions • Updating and backing up BIOS and firmware • Creating reports about the current system (support assistance) Automation Panel 900 user's manual V2.22...
Page 141: Installation
The ADI driver is already included in B&R images of embedded operating systems. If a more current ADI driver version exists (see the Downloads section of the B&R website), it can be installed later. It is important that Enhanced Write Filter (EWF) is disabled for this. Automation Panel 900 user's manual V2.22...
Page 142: B&R Automation Device Interface (Adi) Development Kit
• Automation PC 2100 • Panel PC 300 • Panel PC 700 • Panel PC 800 • Panel PC 900 • Panel PC 2100 • Power Panel 100/200 • Power Panel 300/400 • Power Panel 500 Automation Panel 900 user's manual V2.22...
Page 143 A detailed description of how to use ADI functions can be found in the help system. The B&R Automation Device Interface (ADI) development kit is available at no cost in the Downloads section of the B&R website (www.br-automation.com). Automation Panel 900 user's manual V2.22...
Page 144: B&R Automation Device Interface (Adi) .Net Sdk
• Automation PC 2100 • Panel PC 300 • Panel PC 700 • Panel PC 800 • Panel PC 900 • Panel PC 2100 • Power Panel 100/200 • Power Panel 300/400 • Power Panel 500 Automation Panel 900 user's manual V2.22...
Page 145 B&R images of embedded operating systems. A detailed description of how to use ADI functions can be found in the help system. The ADI .NET SDK is available in the Downloads section of the B&R website (www.br-automation.com). Automation Panel 900 user's manual V2.22...
Page 146: B&R Key Editor
• Assignment of functions to LEDs (HDD access, power, etc.) • 4 assignments possible per key (using layers) • Configuration of the panel locking time when multiple Automation Panel 900 devices are connected to Automation PC and Panel PC devices.
Page 147 A detailed guide for configuring keys and LEDs can be found in the B&R Key Editor's help system. The B&R Key Editor is available at no cost in the Downloads section of the B&R website (www.br-automation.com). It can also be found on the B&R HMI Drivers & Utilities DVD (model number 5SWHMI.0000-00). Automation Panel 900 user's manual V2.22...
Page 148: Standards And Certifications
These devices satisfy the requirements of EC directive "2006/95/EC Low voltage directive" and are designed for the following areas: EN 61131-2:2007 Programmable logic controllers - Part 2: Equipment requirements and tests EN 60204-1:2006 + Safety of machinery - Electrical equipment of machines - Part 1: General requirements A1:2009 Automation Panel 900 user's manual V2.22...
Page 149: Certifications
Eurasian Customs Union (based on EU conformity). 5.2.3 KC Products with this mark are tested by an accredited test laboratory and permitted to be introduced into the Korean market (based on EU conformity). Automation Panel 900 user's manual V2.22...
Page 150: Gl Certification (Germanischer Lloyd)
Connector, 24 VDC, 3-pin female, screw clamps 3.31 mm², protected against vibration by the screw flange 0TB103.91 Connector, 24 VDC, 3-pin female, cage clamp terminal block 3.31 mm², protected against vibration by the screw flange 5AC804.MFLT-00 Line filter Table 65: DNV certifications Automation Panel 900 user's manual V2.22...
Page 151: Sdl Flex Cable Test Description
• Touch screen functionality • USB mouse functionality • Hot plugging functionality tested by disconnecting the USB cable • After a test duration of 150,000 cycles, testing was concluded with a result of "OK". Automation Panel 900 user's manual V2.22...
Page 152: Cable Drag Chain
• Touch screen functionality • USB mouse functionality • Hot plugging functionality tested by disconnecting the USB cable • After a test duration of 300,000 cycles, testing was concluded with a result of "OK". Automation Panel 900 user's manual V2.22...
Page 153: Accessories
All components listed in this manual have undergone intensive system and compatibility testing and been approved accordingly. B&R cannot assume any functional warranty for accessories that have not been approved. Automation Panel 900 user's manual V2.22...
Page 154: 0Tb103.9X
Yes, but applies only if all components installed in the complete system have this certification and are listed on the associated DNV GL certificate for the product family. The cage clamp terminal block cannot be used side by side. The respective limit data of the I/O modules must be taken into account! Automation Panel 900 user's manual V2.22...
Page 155: Terminal Blocks
Electrical properties Nominal voltage 300 V Nominal current 10 A / contact Contact resistance ≤5 mΩ Table 69: 0TB103.8 - Technical data The limit data for each I/O module must be taken into consideration. Automation Panel 900 user's manual V2.22...
Page 156: Legend Strip Templates
10,4" Automation Panel 5AP980.1043-01; for 3 devices. 5AC900.150X-01 Legend Strips Template 15,0" Automation Panel 5AP951.1505-01, 5AP980.1505-01 and 5AP981.1505-01 and Panel PC 5PC781.1505-00; for 4 devices. Table 70: 5AC900.104X-03, 5AC900.104X-04, 5AC900.104X-05, 5AC900.150X-01 - Order data Automation Panel 900 user's manual V2.22...
Page 157: Cables
≥5x cable diameter (male connector - ferrite bead and ferrite bead - ferrite bead) Weight Approx. 260 g Approx. 460 g Approx. 790 g Table 72: 5CADVI.0018-00, 5CADVI.0050-00, 5CADVI.0100-00 - Technical data Yes, although applies only if all components installed within the complete system have this certification. Automation Panel 900 user's manual V2.22...
Page 158 Ferrite bead Connector Bend radius Bend radius Connector - Ferrite bead Ferrite bead - Ferrite bead Ferrite bead Ferrite bead Figure 116: Bend radius specification 6.4.1.1.5 Dimensions 25±5 28.5 Length Figure 117: 5CADVI.0xxx-00 - Dimensions Automation Panel 900 user's manual V2.22...
Page 159 If a field-assembled cable is used, B&R cannot guarantee its functionality. Functionality is only guar- anteed for the cables available from B&R. DVI-D (24+1), male DVI-D (24+1), male Cable shield Cable shield Figure 118: 5CADVI.0xxx-00 - Pinout Automation Panel 900 user's manual V2.22...
Page 160: Sdl Cables
Approx. 1500 g Approx. 2250 g Approx. 2880 g Approx. 4800 g Approx. 5520 g Table 74: 5CASDL.0018-00, 5CASDL.0050-00, 5CASDL.0100-00, 5CASDL.0150-00, 5CASDL.0200-00, 5CASDL.0250-00, 5CASDL.0300-00 - Technical data Yes, although applies only if all components installed within the complete system have this certification. Automation Panel 900 user's manual V2.22...
Page 161 Ferrite bead Connector Bend radius Bend radius Connector - Ferrite bead Ferrite bead - Ferrite bead Ferrite bead Ferrite bead Figure 119: Bend radius specification 6.4.2.1.5 Dimensions 35±5 28.5 Length Figure 120: 5CASDL.0xxx-00- Dimensions Automation Panel 900 user's manual V2.22...
Page 162 If a field-assembled cable is used, B&R cannot guarantee its functionality. Functionality is only guar- anteed for the cables available from B&R. DVI (24+1), male DVI (24+1), male Pinout DVI (24+1), male DVI (24+1), male Cable shield Cable shield Figure 121: 5CASDL.0xxx-00 - Pinout Automation Panel 900 user's manual V2.22...
Page 163: Sdl Cables With 45° Connector
Approx. 300 g Approx. 590 g Approx. 2800 g Approx. 2860 g Table 76: 5CASDL.0018-01, 5CASDL.0050-01, 5CASDL.0100-01, 5CASDL.0150-01 - Technical data Yes, although applies only if all components installed within the complete system have this certification. Automation Panel 900 user's manual V2.22...
Page 164 Ferrite bead Connector Bend radius Bend radius Connector - Ferrite bead Ferrite bead - Ferrite bead Ferrite bead Ferrite bead Figure 122: Bend radius specification 6.4.3.1.5 Dimensions 35±5 28.5 Length Figure 123: 5CASDL.0xxx-01 - Dimensions Automation Panel 900 user's manual V2.22...
Page 165: Cable Pinout
If a field-assembled cable is used, B&R cannot guarantee its functionality. Functionality is only guar- anteed for the cables available from B&R. DVI (24+1), male DVI (24+1), male Pinout DVI (24+1), male DVI (24+1), male Cable shield Cable shield Figure 124: 5CASDL.0xxx-01 - Pinout Automation Panel 900 user's manual V2.22...
Page 166: Sdl Flex Cables
UL AWM 20236 80°C 30 V Flame-retardant In accordance with UL758 (cable vertical flame test) Oil and hydrolysis resistance In accordance with VDE 0282-10 Table 78: 5CASDL.0018-03, 5CASDL.0050-03, 5CASDL.0100-03, 5CASDL.0150-03, 5CASDL.0200-03, 5CASDL.0250-03, 5CASDL.0300-03 - Technical data Automation Panel 900 user's manual V2.22...
Page 167 Bend radius Bend radius Connector - Ferrite bead Ferrite bead - Ferrite bead Ferrite bead Ferrite bead Figure 125: Bend radius specification 6.4.4.1.5 Dimensions 36.5 ±10 37.5 ±2.5 Length Figure 126: 5CASDL.0xxx-03 - Dimensions Automation Panel 900 user's manual V2.22...
Page 168 SDL- TMDS data 2 / SDL shield TMDS data 2 / SDL shield TMDS data 2+ TMDS data 2+ TMDS data 2- TMDS data 2- Cable shield Cable shield Figure 127: 5CASDL.0xxx-03 - Pinout Automation Panel 900 user's manual V2.22...
Page 169: Sdl Flex Cables With Extender
Oil and hydrolysis resistance In accordance with VDE 0282-10 Environmental conditions Temperature Storage -20 to 60°C Fixed installation -20 to 60°C Flexible installation -5 to 60°C Table 81: 5CASDL.0300-13, 5CASDL.0400-13, 5CASDL.0430-13 - Technical data Automation Panel 900 user's manual V2.22...
Page 170 Flex radius Flex radius Male connector - Ferrite bead Ferrite bead - Extender Ferrite bead Extender Figure 128: Flex radius specification with extender 6.4.5.1.5 Dimensions 36.5 ±10 37.5 ±2.5 Length Figure 129: 5CASDL.0xx0-13 - Dimensions Automation Panel 900 user's manual V2.22...
Page 171 If a field-assembled cable is used, B&R cannot guarantee its functionality. Functionality is only guar- anteed for the cables available from B&R. DVI (24+1), male DVI (24+1), male Pinout DVI (24+1), male DVI (24+1), male Cable shield Cable shield Figure 130: 5CASDL.0xx0-13 - Pinout Automation Panel 900 user's manual V2.22...
Page 172 • Connect the end labeled "SDL IN" with the video output of the APC910 (monitor/panel output) or Panel OUT of an AP900 AP Link card. • Connect the "SDL OUT" end to the display unit (e.g. Automation Panel 900) via the Automation Panel Link plug-in card (Panel IN).
Page 173: Sdl3 Cables
IP20, only when connected properly Environmental conditions Temperature Storage -40 to 70°C Fixed installation -40 to 70°C Flexible installation -40 to 70°C -10 to 50°C Table 83: 5CASD3.0100-00, 5CASD3.0150-00, 5CASD3.0200-00, 5CASD3.0300-00, 5CASD3.0500-00, 5CASD3.1000-00 - Technical data Automation Panel 900 user's manual V2.22...
Page 174 If a field-assembled cable is used, B&R cannot guarantee its functionality. Functionality is only guar- anteed for the cables available from B&R. Pinout per TIA/EIA 568A wh/gn wh/or wh/bl wh/br Shield Figure 135: 5CASD3.xxxx-00 - Pinout Automation Panel 900 user's manual V2.22...
Page 175 100 m is not permitted. B&R device Patch panel Patch panel B&R device Patch cable Field-assembled cable Patch cable Max. 5 m Max. 5 m Max. 100 m Figure 136: Wiring with a field-assembled cable Automation Panel 900 user's manual V2.22...
Page 176: Usb Cables
If a field-assembled cable is used, B&R cannot guarantee its functionality. Functionality is only guar- anteed for the cables available from B&R. USB type A, male USB type B, male Jacket Jacket Figure 137: 5CAUSB.00xx-00 USB cables - Pinout Automation Panel 900 user's manual V2.22...
Page 177: Rs232 Cables
Max. 0.5 Nm Mechanical characteristics Dimensions Length 1.8 m ±50 mm 5 m ±80 mm 10 m ±100 mm Diameter Max. 5 mm Flex radius Min. 70 mm Table 87: 9A0014.02, 9A0014.05, 9A0014.10 - Technical data Automation Panel 900 user's manual V2.22...
Page 178 If a field-assembled cable is used, B&R cannot guarantee its functionality. Functionality is only guar- anteed for the cables available from B&R. DSUB (9-pin), male DSUB (9-pin), female Pin assignments DSUB (9-pin), male DSUB (9-pin), female Shield Shield Automation Panel 900 user's manual V2.22...
Page 179: Usb Interface Cover
USB interface cover - Flat - For AP920/98x and PPC700 Table 89: 5AC900.1200-01 - Order data 6.5.3 5AC900.1201-00 6.5.3.1 General information Flat front-side USB interface cover for Automation Panel 900, Power Panel 500, Panel PC 700 and Panel PC 800 devices. 6.5.3.2 Order data Order number...
Page 180: 5Ac900.1201-01
Accessories 6.5.4 5AC900.1201-01 6.5.4.1 General information Round front-side knurled USB interface cover (with anti-loss strap) for Automation Panel 900, Power Panel 500, Panel PC 700 and Panel PC 800 devices. 6.5.4.2 Order data Order number Short description Figure Accessories 5AC900.1201-01 USB interface cover M20 IP65 curved Table 91: 5AC900.1201-01 - Order data...
Page 181: Usb Flash Drives
Operating systems Windows XP Professional Windows XP Embedded Windows ME Windows 2000 Windows CE 5.0 Windows CE 4.2 Electrical characteristics Current consumption 650 µA sleep mode, 150 mA read/write Table 93: 5MMUSB.2048-00 - Technical data Automation Panel 900 user's manual V2.22...
Page 182: Temperature/Humidity Diagram
Width 19 mm Length 52.2 mm Height 7.9 mm Table 93: 5MMUSB.2048-00 - Technical data Indicates data being transferred (sending and receiving). 6.6.1.4 Temperature/Humidity diagram Operation Temperature [°C] Figure 138: 5MMUSB.2048-00 - Temperature/Humidity diagram Automation Panel 900 user's manual V2.22...
Page 183: 5Mmusb.xxxx-01
Windows XP Professional Windows XP Embedded Windows ME Windows 2000 Windows CE 5.0 Windows CE 4.2 Electrical characteristics Current consumption Max. 500 μA sleep mode, max. 120 mA read/write Table 95: 5MMUSB.2048-01, 5MMUSB.4096-01 - Technical data Automation Panel 900 user's manual V2.22...
Page 184: Temperature/Humidity Diagram
Length 67.85 mm Height 8.35 mm Table 95: 5MMUSB.2048-01, 5MMUSB.4096-01 - Technical data Indicates data being transferred (sending and receiving). 6.6.2.4 Temperature/Humidity diagram Storage Operation Transport Temperature [°C] Figure 139: 5MMUSB.xxxx-01 - Temperature/Humidity diagram Automation Panel 900 user's manual V2.22...
Page 185: Ap900 Fluorescent Tubes
(see 2 "Technical data" on page 17). Fluorescent tubes can only be replaced on 12.1" and 15" Automation Panel 900 devices. Information: They cannot be replaced on 10.4", 17", 19" and 21.3" Automation Panel 900 devices! The following table lists the fluorescent tubes that can be used for each panel.
Page 186: Line Filter
Overvoltage category per EN 61131-2 Operating conditions Pollution degree per EN 61131-2 Pollution degree 2 Ambient conditions Temperature Operation -25 to 65°C Storage -25 to 65°C Transport -25 to 65°C Mechanical properties Housing Material Galvanized plate Automation Panel 900 user's manual V2.22...
Page 187: Dimensions
• Keep the lines as short as possible (power supply - line filter - end device). • The line filter must be installed on an uncoated, oil-free metallic surface. Line filter End device Figure 142: Connection example Automation Panel 900 user's manual V2.22...
Page 188: Hmi Drivers & Utilities Dvd
• Power Panel 300/400 BIOS user boot logo • Power Panel 500 / Automation PC 510 / Automation PC 511 BIOS • Panel PC 310 Driver for the devices • Automation Device Interface (ADI) • Audio • Chipset • CD-ROM Automation Panel 900 user's manual V2.22...
Page 189 • Windows CE 4.2 • Windows CE 4.1 • Windows CE tools • Windows Embedded Standard 2009 • Windows Embedded Standard 7 • Thin client • Windows NT Embedded • Windows XP Embedded • VNC viewer Automation Panel 900 user's manual V2.22...
Page 190 • Acrobat Reader 5.0.5 (freeware in German, English and French) • Power Archiver 6.0 (freeware in German, English and French) • Internet Explorer 5.0 (German and English) • Internet Explorer 6.0 (German and English) Automation Panel 900 user's manual V2.22...
Page 191: Servicing And Maintenance
Apply the cleaning agent to the cloth first; do not spray it directly onto the device! Never use aggressive solvents, chemicals, abrasive cleaners, compressed air or steam cleaners. Information: Displays with a touch screen should be cleaned at regular intervals. Automation Panel 900 user's manual V2.22...
Page 192: Replacing The Fluorescent Tubes
Servicing and maintenance 7.2 Replacing the fluorescent tubes Danger! Fluorescent tubes may only be replaced by qualified personnel when the Automation Panel 900 device and the entire system are both switched off. 7.2.1 Procedure First step for all units (12.1" and 15"): Remove the cover. Remove the locating screws (1) and insert the card (2).
Page 193: General Information
Figure 144: Warning - Replacing the fluorescent tubes 7.2.1.2 Procedure for 12.1" Automation Panels • Using a small Phillips screwdriver, remove the screws and disconnect the fluorescent tube. Figure 145: 12.1" Automation Panels - Unscrewing and disconnecting Automation Panel 900 user's manual V2.22...
Page 194: Procedure For 15" Automation Panels
• Unplug the fluorescent tube (1). Remove the screws (2) from the fluorescent tubes using a small Phillips screwdriver, and remove the ground (3) from the housing using a size 10 Torx screwdriver. Figure 147: 15" Automation Panels - Unscrewing and disconnecting Automation Panel 900 user's manual V2.22...
Page 195 Figure 148: 15" Automation Panels - Removing the cover and disconnecting • Replace the fluorescent tubes. To do this, carefully pull the tubes out of their holders and replace them with new ones. Figure 149: 15" Automation Panel - Replacing the fluorescent tubes Automation Panel 900 user's manual V2.22...
Page 196: Environmentally Friendly Disposal
Electronics recycling Operating and monitoring devices Uninterruptible power supplies Batteries and rechargeable batteries Cables Paper/Cardboard packaging Paper/Cardboard recycling Plastic packaging material Plastic recycling Disposal must be carried out in accordance with applicable legal regulations. Automation Panel 900 user's manual V2.22...
Page 197: Elo Accutouch Screen
The active area of the touch screen is resistant to these chemicals for a period of one hour at 21°C. A.1.2 Temperature humidity diagram Storage Operation Temperature [°C] Figure 150: Elo AccuTouch screen (5-wire) - Temperature humidity diagram Automation Panel 900 user's manual V2.22...
Page 198: Cleaning
Apply the cleaning agent to the cloth first; do not spray it directly onto the device! Never use aggressive solvents, chemicals, abrasive cleaners, compressed air or steam cleaners. Information: Displays with a touch screen should be cleaned at regular intervals. Automation Panel 900 user's manual V2.22...
Page 199: 5-Wire Amt Touch Screen
Use a damp cloth to clean the device. Use only water with detergent, screen cleaner or alcohol (ethanol) to moisten the cleaning cloth. Apply the cleaning agent to the cloth first; do not spray it directly onto the device! Never use aggressive solvents, chemicals, abrasive cleaners, compressed air or steam cleaners. Automation Panel 900 user's manual V2.22...
Page 200 Appendix A Information: Displays with a touch screen should be cleaned at regular intervals. Automation Panel 900 user's manual V2.22...
Page 201: Panel Overlay
Abrasion-resistant in accordance with DIN 52347 Adhesive strength in accordance with DIN 58 196-K2 (Part 6) Chemical properties Durability according to DIN 50021 - CASS Automation Panel 900 user's manual V2.22...
Page 202: Viewing Angles
Appendix A A.5 Viewing angles For viewing angle specifications (R, L, U, D) of the display types, see the technical data of the individual compo- nents. 6 o'clock direction Automation Panel 900 user's manual V2.22...
Page 203: Mounting Compatibility
A.6 Mounting compatibility This section describes the compatibility of the installation dimensions for Power Panel 100/200, Power Panel 300/400, Power Panel 500, Automation Panel 900, Automation Panel 700 and Panel PC 800 devices according to device display size. The outer dimensions of the device types are identical for the respective display sizes.
Page 204: Compatibility Details
Outer contour of device Cutout for device Figure 154: Mounting compatibility - 5.7" device - Horizontal2 5.7" Power Panel 500 devices and Power Panel 100/200300/400 devices are 100% mounting compatible in the Horizontal2 format. Automation Panel 900 user's manual V2.22...
Page 205: 10.4" Devices
Outer contour of device Cutout for device Figure 156: Mounting compatibility - 10.4" device - Horizontal1 10.4" Power Panel 500 devices and Power Panel 100/200/300/400 devices are 100% mounting compatible in the Horizontal1 format. Automation Panel 900 user's manual V2.22...
Page 206 Figure 157: Mounting compatibility - 10.4" device - Horizontal2 10.4" Power Panel 500, Automation Panel 900 and Panel PC 700 devices are not 100% mounting compatible with Power Panel 100/200/300/400 devices in the Horizontal2 format. The Power Panel 500, Automation Panel 900 and Panel PC 700 devices require a cutout that is 4.5 mm higher (bottom edge).
Page 207: 12.1" Devices
Figure 159: Mounting compatibility - 12.1" device - Horizontal1 12.1" Power Panel 500, Automation Panel 900 and Panel PC 700 devices are not 100% mounting compatible with Power Panel 100/200/300/400 devices in Horizontal1 format. The Power Panel 300/400 and Power Panel 100/200 devices require a cut that is 1.5 mm wider (left and right).
Page 208: 17" Devices
Outer contour of device Cutout for device Figure 162: Mounting compatibility - 17" device - Horizontal1 17" Automation Panel 900 devices are 100% mounting compatible with Panel PC 700 devices in the Horizontal1 format. Automation Panel 900 user's manual V2.22...
Page 209: 19" Devices
Outer contour of device Cutout for device Figure 163: Mounting compatibility - 19" device - Horizontal1 19" Automation Panel 900, Panel PC 700 and Panel PC 800 are 100% mounting compatible in the Horizontal1 format. A.6.2.8 21.3" devices 583 x 464 566 x 447 ±0.5...

B&R Automation Panel 900 User Manual

Quick Links

Need help?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for B&R Automation Panel 900

Summary of Contents for B&R Automation Panel 900

Table of Contents