Supermicro SYS-211E-FRN2T Disassembly Instructions Manual
Supermicro SYS-211E-FRN2T Disassembly Instructions Manual

Supermicro SYS-211E-FRN2T Disassembly Instructions Manual

Hide thumbs Also See for SYS-211E-FRN2T:

Advertisement

Quick Links

WEEE DISASSEMBLY INSTRUCTIONS
SUPERMICRO SYS-211E-FRN2T ENCLOSURE
Abstract
This document provides clear guidance for end-of-life recyclers on how to identify
and disassemble reportable materials in compliance with the Waste Electrical and
Electronic Equipment (WEEE) directive.
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SYS-211E-FRN2T and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Supermicro SYS-211E-FRN2T

  • Page 1 WEEE DISASSEMBLY INSTRUCTIONS SUPERMICRO SYS-211E-FRN2T ENCLOSURE Abstract This document provides clear guidance for end-of-life recyclers on how to identify and disassemble reportable materials in compliance with the Waste Electrical and Electronic Equipment (WEEE) directive.
  • Page 2: Table Of Contents

    Table of Contents Product Views ............................1 Reportable Materials on SYS-221E-FRN2T....................3 Disassemble Instructions .......................... 4 3.3 Step-by-Step Disassembly Instructions ....................7 Removing Cable and Chassis Top Cover ..................7 Removing Hard Disk Drive (HDDD) / Solid State Drive (SDD) ............8 Removing Power Supply .......................
  • Page 3: Product Views

    1. Product Views Front view Rear view Product construct view...
  • Page 5: Reportable Materials On Sys-221E-Frn2T

    2. Reportable Materials on SYS-221E-FRN2T According to Article 8(2) and Annex VII of WEEE directive 2012/19/EU, below materials and components should be selectively treated. Description Notes Quantity Printed Circuit Boards (PCB) or With a surface greater than 10 sq cm 2.4,3.5,4.2,5.1, 7.3, 8.2, Printed Circuit Assemblies (PCA) (Depending on the configuration)
  • Page 6: Disassemble Instructions

    3. Disassemble Instructions The intent of this document is to provide guidance to recyclers on the presence of materials and components at the product / family level, as required by the EU WEEE Directive 2012/10/EU. This document should also help direct recyclers to proper methods for removing parts and general product disassembly instructions.
  • Page 7 Chassis Motherboard Backplane Riser Card Riser Card Screw, Stand-off Cable Cable Battery...
  • Page 8 Power Supply Power Enclosure*2 Screw and Standoff*2 Set Power Supply Module*2 Power Distributor*1 Storage Card and CPU Heat Sink Processor SSD * 2 Power Cable...
  • Page 9: Step-By-Step Disassembly Instructions

    3.3 Step-by-Step Disassembly Instructions 1. Removing Cable and Chassis Top Cover 1. Use the operating system to power down the system. 2. After the system has completely shutdown, disconnect the power cords from the power supply modules. 3. Remove all cables/ unit from the server IO port. 4.
  • Page 10: Removing Hard Disk Drive (Hddd) / Solid State Drive (Sdd)

    2. Removing Hard Disk Drive (HDD) / Solid State Drive (SDD) 1. Push the release button on the drive carrier, which will extend the drive bay handle 2. Use the drive bay handle to pull the drive carrier out of the chassis 3.
  • Page 11: Removing Power Supply

    6. Use a cross screwdriver to remove screws and lift off the PCB Description Dummy Tray HDD/ SSD Hard Drive Enclosure Hard Drive PCB 3. Removing Power Supply 1. Press the release tab on the failed power supply. 2. Use the handle to gently slide the power supply out the back of the chassis. 3.
  • Page 12: Removing Power Distributor

    4. Cut the power leads connected to the fan and lift the main board from the chassis Description Power Supply Power Enclosure Fan Cable Power Module PCB Capacitor 4. Removing Power Distributor 1. Disconnect the power cords from the power supply modules. Remove 4 screws and lift out the power distributor from the chassis 3.
  • Page 13: Removing Backplane

    Remove screw and standoff Description Power Distributor Power Distributor PCB 5. Removing Backplane 1. Remove the backplane 8 screws from the chassis Description Backplane 6. Removing Fan 1. Remove the AIOM and expansion card brackets to access the failed fan's power cable. 2.
  • Page 14: Removing Expansion Card

    Description Cooling Fan 7. Removing Expansion Card 1. Remove the top cover. 2. Remove the screw as shown below. 3. Remove the bracket from the chassis using the square hole at the top of the bracket. Description Expansion Card Expansion Bracket Expansion PCB 8.
  • Page 15 2. Removing the screw from riser card, take away riser card (in red). 3. Removing the screw from riser bracket and lift riser card. Description Air shroud Riser Card Riser Bracket...
  • Page 16: Removing Processor

    9. Removing Processor 1. Use a T30 Torx-bit screwdriver to loosen the four screws. You can start with any screw, but make sure to loosen the screws in a diagonal pattern. 2. Press the four rotating wires inwards to unlatch the PHM from the socket. 3.
  • Page 17: Removing Dimm

    10. Removing DIMM 10.1 1. Hand press both release tabs on the ends of the DIMM module to unlock it 2. Once the DIMM module is loose, remove it from the memory slot Description 10.1 DIMM 11. Removing Motherboard 1. Remove screws, lift out motherboard 2.

Table of Contents