Subscribe to Our Youtube Channel
Related Manuals for Rothenberger P63-S6
Summary of Contents for Rothenberger P63-S6
- Page 1 SOCKET WELDER P63-S6 Gebrauchsanweisung Instruction Manual Manuel d’instructions Manual de instrucciones Manual de instruções 5.3890X Manuale delle istruzioni 5.3891X 5.3892X 5.3893X 5.3896X 5.3897X www.rothenberger.com...
-
Page 2: Safety Advice
INSTRUCTION MANUAL • Please pay attention to these warnings, since they IMPORTANT are important for safe use of the equipment. This manual contains information required for safe • If this instruction manual is lost or damaged, use of this equipment. request a replacement immediately from our representative. - Page 3 9) Do not overload the equipment. Use it only according to its design conditions. 16) Always ask for assistance from an authorised ROTHENBERGER agent if the equipment must be disassembled for repair. 10) Use proper clothing. Our products comply with applicable safety Do not work wearing a tie, loose or "floppy"...
-
Page 4: Description Of The Equipment
INSTRUCTION MANUAL DESCRIPTION OF THE EQUIPMENT $33/,&$7,216 The SOCKET WELDER P63-S6 has been designed to weld tubes and accessories made of PE, PP, PB and PVDF, both in the workshop and on worksites. ,'(17,),&$7,21 2) 3$576 )LJ *HQHUDO YLHZ The main parts that constitute the SOCKET WELDER P63-S6 are shown in Fig. -
Page 5: Technical Characteristics
Temperature range: max.. 330 C Dimensions: 475 x 359 x 110 mm • Mark the length of Weights: the weld on the tube • SOCKET WELDER P63-S6 Thermostatic = 1.5 Kg • SOCKET WELDER P63-S6 Electronic = 1.4 Kg • G-clamp = 0.4 Kg. - Page 6 INSTRUCTION MANUAL )LJ 8VLQJ WKH XQLW RQ LWV OHJV PRECAUTION The unit must not be connected to the mains supply and used for welding whilst the G-clamp )LJ ,QVHUW WKH DGDSWHU V has not been mounted. The legs can be used to •...
- Page 7 INSTRUCTION MANUAL 0RXQW WKH FRUUHFW DGDSWHUV IRU WKH &RQQHFW WKH XQLW WR WKH SRZHU VRXUFH GLDPHWHU RI WKH WXEH WR EH ZHOGHG 9 9 RQWR WKH KHDWLQJ SODWH Check that the red power LED lights when the unit is •...
- Page 8 62&.(7 :(/'(5 36 (OHFWURQLF The time required to reach working temperature is 0RGHO approximately 5 to 7 min. The SOCKET WELDER P63-S6 Electronic Model has a temperature scale marked from 200 C PRECAUTION to 300 °C 260 C - 280 C Working position The parts of the equipment indicated in Fig.
- Page 9 INSTRUCTION MANUAL NOTE The socket welder is equipped with two safety thermostats which disconnect the unit if the temperature reaches 330 ºC and reconnects it when the temperature has fallen to 265 ºC. & 7+( :(/',1* 352&(66 This consists of four steps: heating, assembly, setting and cooling.
- Page 10 INSTRUCTION MANUAL • Without rotating them, introduce the tube into NOTE the accessory until the weld-length mark is Ensure that the region of the weld is not subjected to reached. This operation should be carried out any force during this time. as quickly and carefully as possible, within the &RROLQJ time (MAX ASSEMBLY TIME) shown in Table 2...
- Page 11 INSTRUCTION MANUAL 78%( Max assembly Heating time Cooling time time Setting time (sec) (sec) (min) WALL (sec) DIAMETER (mm) THICKNESS (mm) 7DEOH 3URFHVV WLPHV IRU ZHOGLQJ 33 WXELQJ...
-
Page 12: Troubleshooting
INSTRUCTION MANUAL TROUBLE-SHOOTING CARE AND MAINTENANCE ,QVSHFW WKH DGDSWHUV EHIRUH XVLQJ WKHP If the socket welding device does not operate correctly, check the following points: &DUHIXOO\ UHPRYH DQ\ PDWHULDO UHPDLQLQJ IURP • Check that the unit is connected to a functioning SUHYLRXV ZHOGLQJ RSHUDWLRQV power source of the correct voltage (230 V / 110 V) •...
Need help?
Do you have a question about the P63-S6 and is the answer not in the manual?
Questions and answers