Page 3: Table Of Contents
TABLE OF CONTENTS INTRODUCTION ................7 GETTING TO KNOW YOUR VEHICLE.
Page 4 INTRODUCTION Keyless Enter ‘n Go™ — Passive Entry ..20 Power Mirrors — If Equipped ... 36 Automatic Unlock On Exit Feature — If Equipped .
Page 5 INTERIOR LIGHTS ....43 HOOD ......61 EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS .
Page 6 FUEL SAVER TECHNOLOGY 5.7L AND 6.4L VEHICLE LOADING ....114 STEERING WHEEL AUDIO CONTROLS ..148 ONLY —...
Page 7 BODYWORK..... . . 249 IN CASE OF EMERGENCY Maintenance-Free Battery ... . 213 Protection From Atmospheric Agents .
Page 8 CUSTOMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE ..... 256 Prepare For The Appointment ..256 Prepare A List .
Page 9: Introduction
FCA US LLC aims at a constant improvement of the vehicles produced. For this reason, it reserves the right to make changes to the model described for technical and/or commercial reasons. For further information, contact an authorized dealer. When it comes to service remember that authorized dealers know your Dodge best, have factory-trained technicians, genuine Mopar® parts, and care about your satisfaction.
Page 10: Symbols Key
INTRODUCTION SYMBOLS KEY ROLLOVER WARNING Utility vehicles have a significantly higher rollover rate than other types of vehicles. This vehicle has a higher ground clearance and a higher center of gravity than many pas- WARNING! These statements apply to operating pro- senger vehicles.
Page 11: Vehicle Modifications/Alterations
INTRODUCTION VEHICLE MODIFICATIONS/ALTERATIONS Red Warning Lights Battery Charge Warning Light WARNING! page 76 Any modifications or alterations to this vehicle could seriously affect its roadworthi- ness and safety and may lead to a collision resulting in serious injury or death. Door Open Warning Light page 76 SYMBOL GLOSSARY...
Page 12 INTRODUCTION Red Warning Lights Yellow Warning Lights Oil Pressure Warning Light Electronic Stability Control (ESC) Active Warning Light page 77 page 78 Oil Temperature Warning Light Electronic Stability Control (ESC) OFF Warning Light page 78 page 77 Trailer Brake Disconnected Warning Light Low Washer Fluid Warning Light page 77 page 78...
Page 13 INTRODUCTION Yellow Warning Lights Yellow Indicator Lights Service Adaptive Cruise Control (ACC) Warning Light Forward Collision Warning (FCW) OFF Indicator Light page 79 page 80 Service AWD Warning Light All Wheel Drive (AWD) Low Indicator Light page 79 page 80 Service Stop/Start System Warning Light NEUTRAL Indicator Light page 79...
Page 14 INTRODUCTION Green Indicator Lights White Indicator Lights Cruise Control Set Indicator Light page 80 Adaptive Cruise Control (ACC) Ready Indicator Light page 81 Front Fog Indicator Light page 80 Cruise Control Ready Indicator Light page 81 LaneSense Indicator Light page 81 LaneSense Indicator Light page 81 Parking/Headlights On Indicator Light...
Page 15: Getting To Know Your Vehicle
GETTING TO KNOW YOUR VEHICLE To Lock/Unlock The Doors And Liftgate KEYS Push and release the unlock button on the key fob once to unlock the driver’s door, or twice within five seconds KEY FOB to unlock all the doors and the liftgate. To lock all the Your vehicle is equipped with a key fob which supports doors and the liftgate, push the lock button once.
Page 16 GETTING TO KNOW YOUR VEHICLE The vehicle’s horn will rapidly chirp three times along with a single flash of the vehicle’s exterior lights. NOTE: • The doors have to be open and then closed in order for the vehicle to detect a key fob. The Key Left Vehicle feature will activate when the first door is closed and no key fob is detected in the vehicle.
Page 17: Sentry Key
GETTING TO KNOW YOUR VEHICLE After placing the ignition switch in the ON/RUN position, WARNING! WARNING! the Vehicle Security Light will turn on for three seconds for a bulb check. If the light remains on after the bulb • • The integrated key fob contains a coin cell battery.
Page 18: Ignition Switch
GETTING TO KNOW YOUR VEHICLE IGNITION SWITCH WARNING! • Engine is not started • • Before exiting a vehicle, always shift the automatic Some electrical devices are available (e.g. power KEYLESS ENTER ‘N GO™ IGNITION transmission into PARK and apply the parking windows, etc.) brake.
Page 19: Remote Start - If Equipped
GETTING TO KNOW YOUR VEHICLE NOTE: • HOW TO USE REMOTE START Hazard switch off • Brake pedal not pressed • For more information on normal starting proce- Push and release the Remote Start button on the key • Battery at an acceptable charge level dures, see page 83.
Page 20: Remote Start Front Defrost Activation
GETTING TO KNOW YOUR VEHICLE NOTE: The Remote Start system will turn the engine off if the REMOTE START COMFORT Remote Start button on the key fob is pushed again, or These features will stay on through the duration of SYSTEMS —...
Page 21: Vehicle Security System - If Equipped
GETTING TO KNOW YOUR VEHICLE VEHICLE SECURITY SYSTEM — TO DISARM THE SYSTEM you are in the vehicle or not. If you remain in the vehicle and open a door, the alarm will sound. If this occurs, The Vehicle Security system can be disarmed using any IF EQUIPPED disarm the Vehicle Security system.
Page 22: Doors
GETTING TO KNOW YOUR VEHICLE DOORS If the lock knob is down when the door is closed, the WARNING! door will lock. Make sure the key fob is not inside the • vehicle before closing the door. Allowing children to be in a vehicle unattended is MANUAL DOOR LOCKS dangerous for a number of reasons.
Page 23 GETTING TO KNOW YOUR VEHICLE NOTE: NOTE: • Passive Entry Unlock initiates illuminated approach (low beams, license plate lamp, position lamps) for Either the driver door only or all doors will unlock when • If the vehicle is unlocked, the liftgate will open with whichever duration is set between 0, 30, 60 or you grab hold of the front driver’s door handle, depend- the handle and no key fob is required.
Page 24: Automatic Unlock On Exit Feature - If Equipped
GETTING TO KNOW YOUR VEHICLE NOTE: CHILD-PROTECTION DOOR LOCK When you push the button on the liftgate, either only SYSTEM — REAR DOORS the liftgate will unlock or all doors and the liftgate will unlock, depending on the selected setting in the To provide a safer environment for small children riding Uconnect system page 129.
Page 25: Steering Wheel
GETTING TO KNOW YOUR VEHICLE NOTE: NOTE: WARNING! For emergency exit with the system engaged, move the For vehicles equipped with Driver Memory Settings, use lock knob up (unlocked position), lower the window, and the key fob or the memory switch on the driver's door Do not adjust the steering column while driving.
Page 26: Driver Memory Settings - If Equipped
GETTING TO KNOW YOUR VEHICLE NOTE: NOTE: 1. Place the vehicle’s ignition in the ON/RUN position (do not start the engine). The engine must be running for the heated steering • Your vehicle is equipped with two key fobs, each can wheel to operate.
Page 27: Memory Position Recall
GETTING TO KNOW YOUR VEHICLE Manual Front Passenger Seat SEATS To program your key fobs, perform the following: Forward/Rearward Adjustment 1. Place the vehicle’s ignition in the OFF position. Seats are a part of the Occupant Restraint system of Some models may be equipped with a manual front 2.
Page 28: Manual Adjustment (Rear Seats)
GETTING TO KNOW YOUR VEHICLE Manual Front Passenger Seatback Front Passenger Seat Fold-Flat Feature CAUTION! Adjustment — Recline — If Equipped Do not place any article under a power seat or To adjust the seatback, lift the lever located on the out- To fold the seatback to the flat load-floor position, lift impede its ability to move as it may cause damage to board side of the seat, lean back to the desired position...
Page 29 GETTING TO KNOW YOUR VEHICLE 1. Pull upward on the release lever to release the seat. Fold-Flat Second Row Seats Tumbled Second Row Release Lever NOTE: WARNING! You may experience deformation in the seat cushion 2. Tumble the seat forward using the pull strap located from the seat belt buckles if the seats are left folded for behind the seatback.
Page 30: Rear Captain's Chairs - If Equipped
GETTING TO KNOW YOUR VEHICLE Rear Captain’s Chairs — If Equipped NOTE: 2. Tumble the seat forward using the pull strap located behind the seatback. You may experience deformation in the seat cushion SECOND ROW CAPTAIN’S CHAIRS FOLD-FLAT from the seat belt buckles if the seats are left folded for SEATS an extended period of time.
Page 31: Folding Third Row
GETTING TO KNOW YOUR VEHICLE Folding Third Row NOTE: 3. If your vehicle is equipped with a mini console, there is a stepping pad to allow passengers to easily The second row seats must be in their full upright posi- Both third row seats can be folded forward to increase access the third row seats.
Page 32: Power Adjustment (Front Seats) - If Equipped
GETTING TO KNOW YOUR VEHICLE Adjusting The Seat Up Or Down POWER ADJUSTMENT (FRONT CAUTION! SEATS) — IF EQUIPPED The height of the seats can be adjusted up or down. Do not place any article under a power seat or Pull upward or push downward on the rear of seat Some models may be equipped with eight-way power impede its ability to move as it may cause damage to...
Page 33: Easy Entry/Exit Seat - If Equipped
GETTING TO KNOW YOUR VEHICLE Easy Entry/Exit Seat — If Equipped NOTE: HEATED SEATS — IF EQUIPPED This feature provides automatic driver seat positioning • Once a heat setting is selected, heat will be felt to enhance driver mobility when entering and exiting within two to five minutes.
Page 34: Front Ventilated Seats - If Equipped
GETTING TO KNOW YOUR VEHICLE FRONT VENTILATED SEATS — To adjust the head restraint forward, pull the top of the WARNING! head restraint toward the front of the vehicle as desired IF EQUIPPED • and release. To adjust the head restraint rearward, pull Head restraints should never be adjusted while the the top of the head restraint to the forward most posi- vehicle is in motion.
Page 35: Head Restraint Removal - Rear Seats
GETTING TO KNOW YOUR VEHICLE Head Restraints — Rear Seats Head Restraint Removal — Rear Seats NOTE: For proper routing of a Child Seat Tether, see The head restraints on the outboard seats are not The center head restraint can be adjusted when occu- page 161.
Page 36: Uconnect Voice Recognition - If Equipped
Up word and state your command. Some examples Uconnect 4C/4C NAV With 8.4-inch Display Voice of Wake Up words include “Hey Uconnect” or “Hey Recognition Dodge”. • A passenger can press the VR button shortcut on BASIC VOICE COMMANDS the radio status bar to also issue a command.
Page 37: Additional Information
GETTING TO KNOW YOUR VEHICLE Sun Visor Slide-On-Rod Feature — NOTE: ADDITIONAL INFORMATION If Equipped The Automatic Dimming Mirror feature is disabled when © 2023 FCA US LLC. All rights reserved. Mopar and the vehicle is in REVERSE to improve rear view viewing. Uconnect are registered trademarks and Mopar Owner The sun visor Slide-On-Rod feature allows for additional You can turn the feature on or off by pushing the button...
Page 38: Outside Mirrors With Turn Signal - If Equipped
GETTING TO KNOW YOUR VEHICLE Outside Mirrors Folding Feature POWER MIRRORS — IF EQUIPPED HEATED MIRRORS — IF EQUIPPED All outside mirrors are hinged and may be moved either The power mirror switch is located on the driver's side These mirrors are heated to melt frost or ice. forward or rearward to resist damage.
Page 39: Before You Begin Programming Homelink
GETTING TO KNOW YOUR VEHICLE Use this QR code to access your digital Non-rolling Code Devices ERASING ALL THE HOMELINK® experience. Most devices manufactured before 1995 will not have a CHANNELS rolling code. These devices will also not have a “LEARN” •...
Page 40: Programming Homelink® To A Miscellaneous
GETTING TO KNOW YOUR VEHICLE Rolling Code Garage Door Opener Final Steps REPROGRAMMING A SINGLE WARNING! HOMELINK® BUTTON NOTE: • Your motorized door or gate will open and close You have 30 seconds in which to initiate rolling code To reprogram a single HomeLink® button that has been while you are programming the universal transmit- final step 2, after completing rolling code final step 1.
Page 41: Security
GETTING TO KNOW YOUR VEHICLE 1. Place the ignition in the ON/RUN position. If you unplugged the garage door opener/device for If you have any problems, or require assistance, please programming, plug it back in at this time. call toll-free 1-800-355-3515 or on the Internet at NOTE: Reprogramming A Single HomeLink®...
Page 42: Headlight Switch
GETTING TO KNOW YOUR VEHICLE NOTE: HEADLIGHT SWITCH For vehicles sold in Canada, rotate the headlight switch The headlight switch is located on the left side of the clockwise from the parking lights and instrument panel instrument panel, next to the steering wheel. The head- lights position to the first detent to turn on headlights, light switch controls the operation of the headlights, parking lights, and instrument panel lights.
Page 43: Daytime Running Lights (Drls)
GETTING TO KNOW YOUR VEHICLE NOTE: DAYTIME RUNNING LIGHTS (DRLS) AUTOMATIC HEADLIGHTS The Daytime Running Lights (DRLs) come on whenever • The Automatic High Beam Headlamp Control can be This system automatically turns the headlights on or off the engine is running. The lights will remain on until the turned on or off by selecting or deselecting “Auto according to ambient light levels.
Page 44: Automatic Headlights With Wipers
GETTING TO KNOW YOUR VEHICLE AUTOMATIC HEADLIGHTS WITH FOG LIGHTS — IF EQUIPPED The fog lights will operate only when the parking lights are on or when the vehicle headlights are on low beam. WIPERS The fog lights are turned on by pushing fog light button An indicator light located in the instrument cluster dis- on the headlight switch.
Page 45: Battery Saver
GETTING TO KNOW YOUR VEHICLE BATTERY SAVER To turn the lights off, push the switch a second time. The lights also turn on when a door is opened. The Timers are set to both the interior and exterior lights to lights will also turn on when the unlock button on the protect the life of your vehicle’s battery.
Page 46: Dimmer Control
GETTING TO KNOW YOUR VEHICLE DIMMER CONTROL ILLUMINATED ENTRY CAUTION! The brightness of the instrument panel lighting can be When programmed with the Uconnect system, the Always remove any buildup of snow that prevents the regulated by rotating the dimmer control up (brighter) or headlights and courtesy lights will turn on when you use windshield wiper blades from returning to the parked down (dimmer).
Page 47: Rain Sensing Wipers - If Equipped
GETTING TO KNOW YOUR VEHICLE Windshield Washers Transmission In NEUTRAL Position — When the igni- • RAIN SENSING WIPERS — tion is in the ON position, and the gear selector is in To use the washer, push on the end of the lever (toward IF EQUIPPED NEUTRAL, the Rain Sensing system will not operate the steering wheel) and hold.
Page 48: Climate Controls
GETTING TO KNOW YOUR VEHICLE CLIMATE CONTROLS The Air Conditioning (A/C) button allows the operator to manually activate or deactivate the air conditioning sys- tem. When the air conditioning system is turned on, The Climate Control system allows you to regulate the cool dehumidified air will flow through the outlets into temperature, air flow, and direction of air circulating the cabin.
Page 49 GETTING TO KNOW YOUR VEHICLE AUTO Button SYNC Button CAUTION! Press and release this button on the touch- Press the SYNC button on the touchscreen Failure to follow these cautions can cause damage to screen, or push the button on the faceplate, to toggle the SYNC feature on/off.
Page 50 GETTING TO KNOW YOUR VEHICLE Mode Control Mix Mode Select Mode by pressing the Mode button on Air is directed through the floor, defrost, and the faceplate, or one of the Mode buttons on side window demister outlets. This setting the touchscreen to change the airflow distri- works best in cold or snowy conditions that bution mode.
Page 51 GETTING TO KNOW YOUR VEHICLE REAR AUTO BUTTON REAR BLOWER CONTROL FLOOR MODE Press and release this button on the touch- Rear Blower Control is used to regulate the Press this button on the touchscreen to screen to change the current setting. The amount of air forced through the rear cli- change the air distribution mode to Floor REAR AUTO indicator will illuminate when...
Page 52 GETTING TO KNOW YOUR VEHICLE AUTO BUTTON REAR MODE CONTROL REAR TEMPERATURE LOCK Turn the blower knob to the AUTO setting. Turn the rear mode knob to adjust airflow The Rear Temperature Lock symbol on the This feature automatically controls the rear distribution.
Page 53: Automatic Temperature Control (Atc)
GETTING TO KNOW YOUR VEHICLE Manual Operation Override AUTOMATIC TEMPERATURE OPERATING TIPS CONTROL (ATC) This system offers a full complement of manual over- ride features. The AUTO symbol in the front ATC display CAUTION! Automatic Operation will be turned off when the system is being used in the manual mode.
Page 54: Interior Storage And Equipment
GETTING TO KNOW YOUR VEHICLE Vacation/Storage Stop/Start System — If Equipped INTERIOR STORAGE AND EQUIPMENT For information on maintaining the Climate Control sys- While in an Autostop, the Climate Control system may tem when the vehicle is being stored for an extended automatically adjust airflow to maintain cabin comfort.
Page 55: Front Center Console
GETTING TO KNOW YOUR VEHICLE Front Center Console The front center console contains both an upper and a lower storage area. To open the upper storage compartment, pull upward on the small latch located on the lid. Sunglasses Bin Door Storage Compartment Latches Rear Full Center Console —...
Page 56: Rear Mini Center Console - If Equipped
GETTING TO KNOW YOUR VEHICLE Rear Mini Center Console — If Equipped An open storage area, or cubby bin with removable liner, is located in the front of the console. Storage Compartment Rear Push Button Fold-Flat Mode When lifted forward, there is access to the lower stor- Open storage areas, or cubby bins with removable lin- age compartment.
Page 57: Using This Feature
GETTING TO KNOW YOUR VEHICLE Using This Feature By using an external USB device to connect to the USB port: • The audio device can be played on the vehicle’s sound system, providing metadata (artist, track title, album, etc.) information on the radio display. NOTE: Depending on track configuration, track information may not be present on the radio display.
Page 58: Lighted Cupholders - If Equipped
GETTING TO KNOW YOUR VEHICLE LIGHTED CUPHOLDERS — ELECTRICAL POWER OUTLETS The front power outlet is located to the right of the cli- mate controls. IF EQUIPPED Your vehicle is equipped with 12 Volt (13 Amp) power outlets that can be used to power cellular phones, On some vehicles, the front cupholders are equipped small electronics and other low powered electrical with a light ring that illuminates the cupholders for the...
Page 59 GETTING TO KNOW YOUR VEHICLE If your vehicle is equipped with a rear full center con- WARNING! sole, there is also a power outlet located in the lower storage area of the rear full center console. To avoid serious injury or death: •...
Page 60: Power Inverter - If Equipped
GETTING TO KNOW YOUR VEHICLE POWER INVERTER — IF EQUIPPED WIRELESS CHARGING PAD — Place the device inside the prepared area delimited in the mat as shown in the image. Incorrect positioning There is a 115 Volt, 150 W inverter outlet located on IF EQUIPPED will prevent the phone from charging.
Page 61: Windows
GETTING TO KNOW YOUR VEHICLE • iPhone® 12 (including iPod®) is equipped with soft- To open the window part way (manually), push the CAUTION! ware to protect the device from overheating. When switch to the first detent and release it when you want the software is active, the rate of charge is slowed the window to stop.
Page 62: Reset Auto-Up
GETTING TO KNOW YOUR VEHICLE Window Lockout Switch To stop the window from going all the way up during the POWER SUNROOF — IF EQUIPPED Auto-Up operation, push down on the switch briefly. The window lockout switch on the driver's door trim If the window runs into any obstacle during Auto-Up, it The power sunroof switch is located between the sun panel allows you to disable the window controls on the...
Page 63: Opening And Closing The Sunroof
GETTING TO KNOW YOUR VEHICLE SUNSHADE OPERATION IGNITION OFF OPERATION WARNING! • The sunshade can be opened manually. However, the The power sunroof switch can remain active in • Do not allow small children to operate the sunroof. sunshade will open automatically as the sunroof opens. Accessory Delay for up to approximately 10 minutes Never allow your fingers, other body parts, or any after the vehicle’s ignition is placed to the OFF posi-...
Page 64: Closing The Hood
GETTING TO KNOW YOUR VEHICLE 2. Reach under the hood from outside the vehicle, The power liftgate may also be opened or closed by WARNING! move the safety latch to the left and lift the hood. pushing the liftgate button located on the front over- head console.
Page 65: Cargo Area Features
GETTING TO KNOW YOUR VEHICLE Retractable Cargo Area Cover — NOTE: WARNING! If Equipped • The power liftgate buttons will not operate if the • If you are required to drive with the liftgate open, vehicle is in gear or the vehicle speed is above The purpose of this cover is for privacy, not to secure make sure that all windows are closed, and the 0 mph (0 km/h).
Page 66: Cargo Tie-Down Hooks
GETTING TO KNOW YOUR VEHICLE Cargo Tie-Down Hooks WARNING! The cargo tie-downs, located on the cargo area floor, The weight and position of cargo and passengers can should be used to safely secure loads when the vehicle change the vehicle center of gravity and vehicle han- is moving.
Page 67: Deploying The Crossbars
GETTING TO KNOW YOUR VEHICLE DEPLOYING THE CROSSBARS 5. Slide the crossbar into the deploy position by moving CAUTION! it towards the matching letter in the side rail. Be 1. Starting with one crossbar, completely loosen the sure the crossbar is fully deployed with the crossbar Use care when removing and handling the crossbars thumb screws at both ends of the crossbar.
Page 68: Stowing The Crossbars
GETTING TO KNOW YOUR VEHICLE STOWING THE CROSSBARS 3. Position the crossbar along the correct side rail. 5. Once the driver’s side crossbar is in place, tighten Make sure the letters on the crossbar align with the the thumb screws completely. 1.
Page 69 GETTING TO KNOW YOUR VEHICLE NOTE: CAUTION! • To help control wind noise, stow the crossbars in the • Load should always be secured to crossbars first, side rails when they are not in use. with tie down loops used as additional securing •...
Page 70: Getting To Know Your Instrument Panel
GETTING TO KNOW YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER...
Page 71: Instrument Cluster Descriptions
GETTING TO KNOW YOUR INSTRUMENT PANEL Use this QR code to access your digital instrument cluster display can show how systems are CAUTION! experience. working and give you warnings when they are not. The steering wheel mounted controls allow you to scroll Driving with a hot engine cooling system could dam- through the main menus and submenus.
Page 72 GETTING TO KNOW YOUR INSTRUMENT PANEL • Right Arrow Button The system allows the driver to select information by The instrument cluster display will normally display the pushing the following buttons mounted on the steering Push and release the right main menu or the screens of a selected feature of the arrow button to wheel:...
Page 73: Engine Oil Life Reset
GETTING TO KNOW YOUR INSTRUMENT PANEL Vehicles Equipped With Keyless Enter ‘n Go™ — NOTE: ENGINE OIL LIFE RESET Ignition If the indicator message illuminates when you start the Use this QR code to access your digital vehicle, the oil change indicator system did not reset. If Use the steering wheel instrument cluster display con- experience.
Page 74: Instrument Cluster Display Menu Items
GETTING TO KNOW YOUR INSTRUMENT PANEL Vehicle Not In Park Remote Start Active Push Start Button Remote Start Canceled Fuel Low Remote Start Canceled Door Open Remote Start Canceled Hood Open Remote Start Canceled Liftgate Open Remote Start Canceled Time Expired Remote Start Disabled Start To Reset Service Air Bag System Service Air Bag Warning Light...
Page 75: Performance Features - If Equipped
GETTING TO KNOW YOUR INSTRUMENT PANEL Performance Features — If Equipped • • 1/8 Mile (200 meters) Timer Current MPG, L/100 km, or km/L ○ Best • Average MPG, L/100 km, or km/L Push and release the up or down arrow button ○...
Page 76: Screen Setup
GETTING TO KNOW YOUR INSTRUMENT PANEL NOTE: BATTERY SAVER ON/BATTERY Upper Left or Upper Right Press and hold the OK button to reset all the SAVER MODE MESSAGE — None Compass Outside Temp information. ELECTRICAL LOAD REDUCTION Time Range To Empty Fuel Economy Trailer Brake will display the following: (RTE)
Page 77: Warning Lights And Messages
GETTING TO KNOW YOUR INSTRUMENT PANEL What to do when an electrical load reduction action The electrical loads that may be switched off RED WARNING LIGHTS message is present (“Battery Saver On” or “Battery (if equipped), and vehicle functions which can be Saver Mode”) Seat Belt Reminder Warning Light affected by load reduction:...
Page 78: Battery Charge Warning Light
GETTING TO KNOW YOUR INSTRUMENT PANEL Electric Power Steering (EPS) Fault If the light remains on when the parking brake has Vehicles equipped with the Anti-Lock Brake System been disengaged, and the fluid level is at the full mark (ABS) are also equipped with Electronic Brake Force Warning Light on the master cylinder reservoir, it indicates a possible Distribution (EBD).
Page 79 GETTING TO KNOW YOUR INSTRUMENT PANEL Liftgate Open Warning Light Transmission Temperature Warning ON/RUN or ACC/ON/RUN position and remain on briefly as a bulb check. If the light does not come on during Light This warning light will illuminate when the starting, have the system checked by an authorized liftgate is open.
Page 80: Yellow Warning Lights
GETTING TO KNOW YOUR INSTRUMENT PANEL Low Washer Fluid Warning Light — • YELLOW WARNING LIGHTS The ESC OFF Indicator Light and the ESC Indicator Light come on momentarily each time the ignition is If Equipped Anti-Lock Brake System (ABS) Warning placed in the ON/RUN or ACC/ON/RUN position.
Page 81 GETTING TO KNOW YOUR INSTRUMENT PANEL Service AWD Warning Light — WARNING! CAUTION! If Equipped A malfunctioning catalytic converter can reach higher Do not continue driving with one or more flat tires as This telltale will turn on to indicate the All- temperatures than in normal operating conditions.
Page 82: Yellow Indicator Lights
GETTING TO KNOW YOUR INSTRUMENT PANEL Your vehicle has also been equipped with a TPMS mal- YELLOW INDICATOR LIGHTS GREEN INDICATOR LIGHTS function indicator to indicate when the system is not All-Wheel Drive (AWD) Low Indicator Adaptive Cruise Control (ACC) Set With operating properly.
Page 83: White Indicator Lights
GETTING TO KNOW YOUR INSTRUMENT PANEL LaneSense Indicator Light — If Equipped NOTE: BLUE INDICATOR LIGHTS • The LaneSense indicator light illuminates A continuous chime will sound if the vehicle is High Beam Indicator Light solid green when both lane markings have driven more than 1 mile (1.6 km) with either turn been detected and the system is armed and signal on.
Page 84: Onboard Diagnostic System (Obd Ii) Cybersecurity
GETTING TO KNOW YOUR INSTRUMENT PANEL EMISSIONS INSPECTION AND 3. Approximately 15 seconds later, one of two things CAUTION! will happen: ○ MAINTENANCE PROGRAMS • The MIL will flash for about 10 seconds and Prolonged driving with the MIL on could cause fur- then return to being fully illuminated until you ther damage to the emission control system.
Page 85: Starting And Operating
STARTING AND OPERATING To Turn Off The Engine Using The ENGINE START/STOP STARTING THE ENGINE AUTOMATIC TRANSMISSION Button The gear selector must be in the NEUTRAL (N) or PARK Before starting your vehicle, adjust your seat, adjust the 1. Place the gear selector in PARK, then push and (P) position before you can start the engine.
Page 86: Autopark
STARTING AND OPERATING ENGINE START/STOP Button Functions — With Driver’s AutoPark will engage when all of these conditions are WARNING! Foot OFF The Brake Pedal (In PARK Or NEUTRAL met: Position) • • Vehicle is equipped with an 8-speed transmission Driver inattention could lead to failure to place the The ENGINE START/STOP button operates similar to an •...
Page 87: Extended Park Starting
STARTING AND OPERATING 4WD LOW — If Equipped 4. If the engine fails to start after eight attempts, allow WARNING! AutoPark will be disabled when operating the vehicle the starter to cool for at least 10 minutes, then in 4WD LOW. repeat the procedure.
Page 88: Engine Break-In Recommendations
STARTING AND OPERATING • ENGINE BREAK-IN RECOMMENDATIONS PARKING BRAKE This light only shows that the parking brake is applied. It does not show the degree of brake application. — NON-SRT Before leaving the vehicle, make sure that the parking When parking on a hill, it is important to turn the front brake is fully applied and place the gear selector in the wheels toward the curb on a downhill grade and away PARK (P) position.
Page 89: Automatic Transmission
STARTING AND OPERATING WARNING! WARNING! WARNING! • • • Be sure the parking brake is fully disengaged The transmission may not engage PARK if the Do not leave the key fob in or near the vehicle (or before driving; failure to do so can lead to brake vehicle is moving.
Page 90: Brake Transmission Shift Interlock (Btsi) System
STARTING AND OPERATING BRAKE TRANSMISSION SHIFT When the Fuel Economy (ECO) mode is enabled, the The electronically controlled transmission adapts its vehicle control systems will change the following: shift schedule based on driver inputs, along with envi- INTERLOCK (BTSI) SYSTEM ronmental and road conditions.
Page 91: Gear Ranges
STARTING AND OPERATING NOTE: NEUTRAL (N) When exiting the vehicle, always: • If the gear selector cannot be moved to the PARK, Apply the parking brake. Use this range when the vehicle is standing for pro- REVERSE, or NEUTRAL position (when pushed forward) •...
Page 92: Transmission Limp Home Mode
STARTING AND OPERATING AutoStick — If Equipped During cold temperatures, transmission operation may In the event of a momentary problem, the transmission be modified depending on engine and transmission can be reset to regain all forward gears by performing AutoStick is a driver-interactive transmission feature temperature as well as vehicle speed.
Page 93: Sport Mode - If Equipped
STARTING AND OPERATING • SPORT MODE — IF EQUIPPED If a requested downshift would cause the engine to ELECTRONICALLY SHIFTED overspeed, that shift will not occur. TRANSFER CASE — IF EQUIPPED • The system will ignore attempts to upshift at too low Your vehicle is equipped with a SPORT Mode feature.
Page 94: Transfer Case Position Indicator Messages
STARTING AND OPERATING Transfer Case Position Indicator N (Neutral) WARNING! Messages This range disengages both the front and rear drive- shafts from the powertrain. To be used for flat towing Always engage the parking brake when powering The Transfer Case Position Indicator message (AWD behind another vehicle page 123.
Page 95: Tow N Go - If Equipped
STARTING AND OPERATING NOTE: • If all the requirements to select a new transfer case position have been met, the current position indica- • If steps 1 or 2 of either the “Preferred” or “Alternate tor light will turn off, the selected position indicator Procedure”...
Page 96: Guidelines For Track Use
STARTING AND OPERATING NOTE: NOTE: • TOW – TOW drive mode also optimizes the transmis- sion shifting for towing, as well as maximizing Use of DOT 4 brake fluid is suggested for extended It is recommended that you target below 42 psi straight line traction by optimizing driveline settings track usage due to increased thermal capacity.
Page 97: Fuel Saver Technology 5.7L And 6.4L
STARTING AND OPERATING POWER STEERING STOP/START SYSTEM — IF EQUIPPED 6. Occasionally, a second burnish session is required. If the brake pads begin to emit an odor during the next track session, reduce vehicle speed and brak- The electric power steering system will provide The Stop/Start function is designed to reduce fuel con- ing deceleration rate to burnish targets and follow increased vehicle response and ease of maneuverabil-...
Page 98: Possible Reasons The Engine Does Not Autostop
STARTING AND OPERATING POSSIBLE REASONS THE ENGINE It may be possible for the vehicle to be driven several TO MANUALLY TURN OFF THE times without the Stop/Start system going into a STOP/ DOES NOT AUTOSTOP STOP/START SYSTEM START READY state under more extreme conditions of the items previously listed.
Page 99: System Malfunction
STARTING AND OPERATING To Activate SYSTEM MALFUNCTION CRUISE CONTROL Push the on/off button to activate the Cruise Control. If there is a malfunction in the Stop/Start system, the When engaged, the Cruise Control takes over accelera- “CRUISE CONTROL READY” will appear in the instru- system will not shut down the engine.
Page 100: Adaptive Cruise Control (Acc)
STARTING AND OPERATING To Vary The Speed Setting ADAPTIVE CRUISE CONTROL (ACC) WARNING! To Increase Or Decrease The Set Speed Adaptive Cruise Control (ACC) increases the driving con- Cruise Control can be dangerous where the system venience provided by Cruise Control while traveling on When the Cruise Control is set, you can increase speed cannot maintain a constant speed.
Page 101: Adaptive Cruise Control (Acc) Operation
STARTING AND OPERATING Adaptive Cruise Control (ACC) Menu WARNING! WARNING! The instrument cluster display will show the current ACC • When entering a turn lane or highway off-ramp; • Adaptive Cruise Control (ACC) is a convenience system settings. The information it displays depends on when driving on roads that are winding, icy, snow- system.
Page 102: Activating Adaptive Cruise Control (Acc)
STARTING AND OPERATING Activating Adaptive Cruise Control (ACC) To Activate/Deactivate WARNING! The minimum set speed for the ACC system is 20 mph Push and release the Adaptive Cruise Control (ACC) In Fixed Speed Cruise Control mode (ACC not (32 km/h). on/off button.
Page 103: To Turn Off
STARTING AND OPERATING To Cancel To Resume To Vary The Speed Setting To Increase Or Decrease The Set Speed The following conditions cancel the ACC or Fixed Speed If there is a set speed in memory, push the RES Cruise Control systems: (resume) button and remove your foot from the accel- After setting a speed, you can increase the set speed by erator pedal.
Page 104: Setting The Following Distance In Acc
STARTING AND OPERATING NOTE: The vehicle will then maintain the set distance until: When you override and push the SET (+) button or SET • The vehicle ahead accelerates to a speed above the (-) button, the new set speed will be the current speed set speed.
Page 105: Acc Operation At Stop
STARTING AND OPERATING ACC Operation At Stop This most often occurs at times of poor visibility, such When the condition that deactivated the system is no as in snow or heavy rain. The ACC system may also longer present, the system will return to the “Adaptive If the ACC system brings your vehicle to a standstill become temporarily blinded due to obstructions, such Cruise Control Off”...
Page 106 STARTING AND OPERATING TOWING A TRAILER TURNS AND BENDS If weather conditions are not a factor, the driver should examine the windshield and the camera located on the ACC while towing a trailer is recommended only with an When driving on a curve with ACC engaged, the system back side of the inside rearview mirror.
Page 107: Parksense Front/Rear Park Assist
STARTING AND OPERATING LANE CHANGING PARKSENSE FRONT/REAR PARK ASSIST ACC may not detect a vehicle until it is completely in the SYSTEM — IF EQUIPPED lane in which you are traveling. In the following lane changing example, ACC has not yet detected the vehicle The ParkSense Park Assist system provides visual and changing lanes and it may not detect the vehicle until audible indications of the distance between the rear,...
Page 108: Parksense Sensors
STARTING AND OPERATING • The automatic emergency braking function can be PARKSENSE SENSORS enabled/disabled from the Customer Programmable Six ParkSense sensors located in the front fascia/ Features section of the Uconnect system. bumper (if equipped) and six ParkSense sensors (four •...
Page 109 STARTING AND OPERATING Front/Rear ParkSense Arcs 1 — No Tone/Solid Arc 6 — Fast Tone/Flashing Arc 2 — No Tone/Flashing Arc 7 — Fast Tone/Flashing Arc 3 — Fast Tone/Flashing Arc 8 — Slow Tone/Solid Arc 4 — Continuous Tone/Flashing Arc 9 —...
Page 110 STARTING AND OPERATING The vehicle is close to the obstacle when the instrument cluster display shows one flashing arc and sounds a continuous tone. The following chart shows the warning alert opera- tion when the system is detecting an obstacle: WARNING ALERTS FOR REAR Rear Distance Greater than...
Page 111: Parksense Warning Display
STARTING AND OPERATING Front Park Assist Audible Alerts When the ParkSense switch is pushed to disable the When the vehicle is connected to a trailer, the instru- system, the instrument cluster will display the ment cluster display will show the "Rear ParkSense ParkSense will turn off the Front Park Assist audible “PARKSENSE OFF”...
Page 112: Service The Parksense Park Assist System
STARTING AND OPERATING • SERVICE THE PARKSENSE PARK CLEANING THE PARKSENSE Use the ParkSense switch to turn the ParkSense system off if objects such as bicycle carriers, trailer ASSIST SYSTEM SYSTEM hitches, etc. are placed within 12 inches (30 cm) of During vehicle start up, when the ParkSense System the rear fascia/bumper.
Page 113: Lanesense - If Equipped
STARTING AND OPERATING When only a single lane marking is detected and the LANESENSE WARNING MESSAGE CAUTION! driver drifts across the lane marking (no turn signal The LaneSense system will indicate the current lane applied), the LaneSense system provides visual warn- •...
Page 114 STARTING AND OPERATING • When the LaneSense system senses the lane has been approached and is in a lane departure situa- tion, the left lane line flashes yellow (on/off). The LaneSense telltale changes from solid yellow to flashing yellow. At this time torque is applied to the steering wheel in the opposite direction of the lane boundary.
Page 115: Changing Lanesense Status
STARTING AND OPERATING Manual Activation Of The Back Up Camera CHANGING LANESENSE STATUS The following table shows the approximate distances for each zone: 1. Press the Vehicle Menu button located at the bot- The LaneSense system has settings to adjust the inten- tom of the Uconnect display.
Page 116: Refueling The Vehicle
STARTING AND OPERATING CAUTION! CAUTION! • To avoid vehicle damage, ParkView should only be To avoid fuel spillage and overfilling, do not “top off” used as a parking aid. The ParkView camera is the fuel tank after filling. unable to view every obstacle or object in your drive path.
Page 117: Inflation Pressure
STARTING AND OPERATING Gross Axle Weight Rating (GAWR) Loading TRAILER TOWING The GAWR is the maximum permissible load on the The actual total weight and the weight of the front and In this section you will find safety tips and information front and rear axles.
Page 118: Gross Combination Weight Rating (Gcwr)
STARTING AND OPERATING Tongue Weight (TW) Weight-Distributing Hitch WARNING! The TW is the downward force exerted on the hitch ball A weight-distributing system works by applying leverage If the gross trailer weight is 5,000 lb (2,267 kg) or by the trailer. You must consider this as part of the load through spring (load) bars.
Page 119: Trailer Hitch Classification
STARTING AND OPERATING RECOMMENDED DISTRIBUTION HITCH 2. Attach the trailer to the vehicle without the weight 5. The vehicle can now be driven. distribution bars connected. ADJUSTMENT Measurement Example Example Height (mm) 3. Measure the height from the top of the front wheel 1.
Page 120: Trailer Towing Weights (Maximum Trailer Weight Ratings) - Non-Srt
STARTING AND OPERATING TRAILER TOWING WEIGHTS (MAXIMUM TRAILER WEIGHT RATINGS) — NON-SRT Engine GCWR Maximum GTW Maximum Trailer TW (See Note) 3.6L - RWD Light Duty Cooling 8,900 lb (4,037 kg) 3,500 lb (1,588 kg) 350 lb (159 kg) 3.6L - RWD 11,600 lb (5,262 kg) 6,200 lb (2,812 kg) 620 lb (281 kg)
Page 121: Trailer And Tongue Weight
STARTING AND OPERATING NOTE: Consider the following items when computing the WARNING! weight on the rear axle of the vehicle: Be sure to engage all tabs of the hitch receiver cover in • the bumper fascia prior to installation. The tongue weight of the trailer. Improper towing can lead to a collision.
Page 122: Towing Requirements - Tires
STARTING AND OPERATING Towing Requirements — Tires WARNING! • Do not attempt to tow a trailer while using a com- • Do not connect trailer brakes to your vehicle's pact spare tire. hydraulic brake lines. It can overload your brake •...
Page 123 STARTING AND OPERATING Trailer Brake Status Indicator Light Display Messages 3. When a trailer with electric/EOH brakes is plugged in, the trailer connected message should appear in This light indicates the trailer electrical connection The trailer brake control interacts with the instrument the instrument cluster display (if the connection is status.
Page 124: Towing Requirements - Trailer Lights And Wiring
STARTING AND OPERATING Towing Requirements — Trailer Lights And Wiring Whenever pulling a trailer, regardless of the trailer size, stoplights and turn signals on the trailer are required for motoring safety. The Trailer Tow Package may include a four- and seven- pin wiring harness.
Page 125: Towing Tips
STARTING AND OPERATING NOTE: • TOWING TIPS To prevent excess heat generation, avoid continuous driving at high RPM. Reduce vehicle speed as nec- Using a lower gear while operating the vehicle under Before towing, practice turning, stopping, and backing essary to avoid extended driving at high RPM. heavy loading conditions, will improve performance and up the trailer in an area located away from heavy traffic.
Page 126: Recreational Towing - Rear-Wheel Drive Models
STARTING AND OPERATING NOTE: RECREATIONAL TOWING — RECREATIONAL TOWING — If the Mopar® Flat Tow Harness kit is installed, the EPS REAR-WHEEL DRIVE MODELS ALL-WHEEL DRIVE MODELS will use power from the battery to keep the EPS pow- (SINGLE-SPEED TRANSFER CASE) DO NOT flat tow this vehicle.
Page 127 STARTING AND OPERATING Shifting Into N (Neutral) NOTE: ○ Steps 1 through 3 are requirements that must be met before pushing the N (Neutral) button, and WARNING! must continue to be met until the shift has been completed. If any of these requirements are not You or others could be injured or killed if you leave met before pushing the N (Neutral) button or are the vehicle unattended with the transfer case in the N...
Page 128: Driving Tips
STARTING AND OPERATING ○ The ignition must be in the ON/RUN mode for a 12. Start the engine. CAUTION! shift to take place and for the position indicator 13. Press and hold the brake pedal. lights to be operable. If the ignition is not in the Damage to the transmission may occur if the trans- ON/RUN mode, the shift will not take place and 14.
Page 129: Off-Road Driving Tips
STARTING AND OPERATING Driving In Snow, Mud And Sand OFF-ROAD DRIVING TIPS Driving through water more than a few inches/ centimeters deep will require extra caution to ensure In heavy snow, when pulling a load, or for additional When To Use 4WD Low — If Equipped safety and prevent damage to your vehicle.
Page 130: Traction Downhill
STARTING AND OPERATING • Completely inspect the underbody of your vehicle. WARNING! Check tires, body structure, steering, suspension, and exhaust system for damage. If the engine stalls, you lose forward motion, or can- • Inspect the radiator for mud and debris and clean not make it to the top of a steep hill or grade, never as required.
Page 131: Multimedia
MULTIMEDIA UCONNECT SYSTEMS UCONNECT SETTINGS WARNING! • For detailed information about your Uconnect 4C/4C The Uconnect system uses a combination of buttons on ONLY insert trusted media devices/components NAV With 8.4-inch Display or Uconnect 5 NAV With 10.1- the touchscreen and buttons on the faceplate located into your vehicle.
Page 132: Customer Programmable Features
MULTIMEDIA NOTE: NOTE: CUSTOMER PROGRAMMABLE FEATURES • • Only one touchscreen area may be selected at a Only one touchscreen area may be selected at a time. time. • • Depending on the vehicle’s options, feature settings Depending on the vehicle’s options, feature settings may vary.
Page 133 MULTIMEDIA Language When the Language button is pressed on the touchscreen, the system displays the different language options. Once an option is selected, the system will display in the chosen language. The available setting is: NOTE: Depending on the vehicle’s options, feature settings may vary. Setting Name Description Language...
Page 134 MULTIMEDIA Setting Name Description Units This setting changes the “Speed” (MPH or km/h), “Distance” (mi or km), “Fuel Consumption” (MPG [US], MPG [UK], L/100 km, or km/L), “Pressure” (psi, kPa, or bar), “Temperature” (°C or °F), “Power” (SRT only) (HP [US], HP [UK], or kW), and “Torque”...
Page 135: Setting Name
This setting will allow you to change the voice options for the radio to “Male” or “Female”. Wake Up Word This setting will change the system’s “Wake Up” word. The available options are “Hey Uconnect” and “Hey Dodge”. Voice Barge-in This setting will allow voice barge-in to be turned on and off.
Page 136: Safety & Driving Assistance
MULTIMEDIA Setting Name Description Auto-On Driver Heated/Ventilated Seat & Heated This setting will activate the vehicle’s comfort systems and heated seats or heated steering wheel when the vehicle is Steering Wheel With Vehicle Start remote started or ignition is started. The “Off” setting will not activate the comfort systems. The “Remote Start” setting will only activate the comfort systems when using Remote Start.
Page 137 MULTIMEDIA Setting Name Description This setting will alert the driver by vibrating the steering wheel and moving the steering wheel when a lane departure is detected. The available options within Active Lane Management are Lane Management “Vibration Only”, “Steering Assist Active Lane Management Only”, and “Vibration + Steering Assist”;...
Page 138 MULTIMEDIA Units When the Units button is pressed on the touchscreen, the system displays the different measurement options. The selected unit of measurement will display in the instrument cluster display and Navigation system (if equipped). The available settings are: NOTE: Depending on the vehicle’s options, feature settings may vary.
Page 139 MULTIMEDIA Setting Name Description Time Format This setting will allow you to set the time format (AM/PM). Sync Time With GPS must be off for this setting to be available. The “12 hrs” setting will set the time to a 12-hour format. The “24 hrs” setting will set the time to a 24-hour format. Set Time This setting will allow you to set the hours and minutes.
Page 140: Navigation - If Equipped
Command List off. Wake Up Word This setting will change the system’s “Wake Up” word. The available options are “Hey Uconnect” and “Hey Dodge”. Voice Barge-in This setting will turn the Voice Barge-in function on or off.
Page 141 MULTIMEDIA Trailer When the Trailer button is pressed on the touchscreen, the system will display settings related to trailer towing. NOTE: Depending on the vehicle’s options, feature settings may vary. Setting Name Description Trailer Select Select from “Trailer 1”, “Trailer 2”, “Trailer 3”, and “Trailer 4”. These trailer designations can be used to save different trailer settings.
Page 142 MULTIMEDIA Mirrors & Wipers When the Mirrors & Wipers button is pressed on the touchscreen, the system displays the options related to the vehicle’s mirrors and wipers. NOTE: Depending on the vehicle’s options, feature settings may vary. Setting Name Description Tilt Side Mirrors In Reverse This setting will tilt the outside side-view mirrors when the ignition is in the ON/RUN position and the transmission gear selector is in the REVERSE position.
Page 143: Doors And Locks
MULTIMEDIA Setting Name Description Auto Dim High Beams This setting will allow you to turn the Auto Dim High Beams on or off. Daytime Running Lights This setting will allow you to turn the Daytime Running Lights on or off. Flash Lights With Lock This setting will allow you to turn the flashing of the lights when the Lock button is pushed on the key fob on or off.
Page 144 MULTIMEDIA Seats & Comfort/Auto-On Comfort — If Equipped When Seats & Comfort/Auto-On Comfort button is pressed on the touchscreen, the system displays the options related to the vehicle’s comfort systems when remote start has been activated or the vehicle has been started. NOTE: Depending on the vehicle’s options, feature settings may vary.
Page 145 MULTIMEDIA Audio When the Audio button is pressed on the touchscreen, the system displays options related to the vehicle’s sound system. These settings can change the audio location within the vehicle, adjust the bass or treble levels, and auto-play settings from an audio device or smartphone. NOTE: Depending on the vehicle’s options, feature settings may vary.
Page 146: Aux Switches
MULTIMEDIA AUX Switches When the AUX Switches button is pressed on the touchscreen, the system displays the options related to the four vehicle AUX switches. NOTE: Depending on the vehicle’s options, feature settings may vary. Setting Name Description AUX 1-4 This setting will adjust the type and power source for the four vehicle AUX switches.
Page 147: Siriusxm® Setup
MULTIMEDIA SiriusXM® Setup When the SiriusXM® Setup button is pressed on the touchscreen, the system displays options related to SiriusXM® satellite radio. These settings can be used to skip specific radio channels and restart favorite songs from the beginning. NOTE: •...
Page 148: Software Update
MULTIMEDIA Software Update When the Software Update button is selected, the system will display a menu with possible Wi-Fi connections. From this page, you can select and connect to one of the avail- able Wi-Fi networks to begin system software updates. To begin, make sure the system is set to allow for Wi-Fi updates. 1.
Page 149 MULTIMEDIA Reset When the Reset button is pressed on the touchscreen, the system displays the options related to resetting the Uconnect system back to its default settings. These settings can clear personal data and reset selected settings from other menus. NOTE: Depending on the vehicle’s options, feature settings may vary.
Page 150: Steering Wheel Audio Controls
MULTIMEDIA STEERING WHEEL AUDIO CONTROLS The following describes the left-hand control operation REGULATORY AND SAFETY in each mode: INFORMATION The remote sound system controls are located on the RADIO OPERATION US/CANADA rear surface of the steering wheel at the three and nine o’clock positions.
Page 151: Safety
SAFETY Anti-Lock Brake System (ABS) Warning SAFETY FEATURES WARNING! Light • The ABS contains sophisticated electronic equip- ANTI-LOCK BRAKE SYSTEM (ABS) The yellow ABS Warning Light will turn on when the igni- ment that may be susceptible to interference tion is placed in the ON/RUN mode and may stay on for caused by improperly installed or high output radio The ABS provides increased vehicle stability and brake as long as four seconds.
Page 152: Electronic Brake Control (Ebc) System
SAFETY Brake Assist System (BAS) Brake System Warning Light WARNING! The BAS is designed to optimize the vehicle’s braking The red Brake System Warning Light will turn on when • Before exiting a vehicle, always come to a com- capability during emergency braking maneuvers. The the ignition is placed in the ON/RUN mode and may plete stop, then shift the automatic transmission system detects an emergency braking situation by...
Page 153: Electronic Brake Force Distribution (Ebd)
SAFETY Electronic Brake Force Distribution Electronic Stability Control (ESC) WARNING! (EBD) ESC enhances directional control and stability of the • Electronic Stability Control (ESC) cannot prevent vehicle under various driving conditions. ESC corrects EBD manages the distribution of the braking torque the natural laws of physics from acting on the for oversteering or understeering of the vehicle by between the front and rear axles by limiting braking...
Page 154: Esc Operating Modes
SAFETY ESC Operating Modes flash during acceleration, ease up on the accelerator WARNING! and apply as little throttle as possible. Be sure to adapt Depending upon model and mode of operation, the ESC your speed and driving to the prevailing road •...
Page 155 SAFETY Traction Control System (TCS) • The driver door must be closed. WARNING! • The vehicle must be on a sufficient grade. The TCS monitors the amount of wheel spin of each of • • If you use a trailer brake controller with your trailer, The gear selection must match vehicle uphill direc- the driven wheels.
Page 156: Auxiliary Driving Systems
SAFETY AUXILIARY DRIVING SYSTEMS vehicle when the vehicle speed has reached approxi- The area on the rear fascia/bumper where the radar mately 6 mph (10 km/h) or higher and will alert the sensors are located must remain free of snow, ice, and driver of vehicles in these areas.
Page 157 SAFETY Entering From The Rear Vehicles that come up from behind your vehicle on either side and enter the rear detection zone with a relative speed of less than 30 mph (48 km/h). BSM Warning Light Overtaking/Approaching The BSM system monitors the detection zone from three different entry points (Side, Rear, Front) while driving to see if an alert is necessary.
Page 158: Rear Cross Path (Rcp)
SAFETY WARNING! Rear Cross Path (RCP) detection is not a backup aid system. It is intended to be used to help a driver detect an oncoming vehicle in a parking lot situation. Drivers must be careful when backing up, even when using RCP.
Page 159: Forward Collision Warning (Fcw) With Mitigation
SAFETY NOTE: NOTE: When the system determines a collision with the vehicle in front of you is no longer probable, the Whenever an audible alert is requested by the BSM FCW monitors the information from the forward looking warning message will be deactivated. system, the radio is also muted.
Page 160: Fcw Braking Status And Sensitivity
SAFETY FCW Braking Status And Sensitivity Service FCW Warning NOTE: The FCW Sensitivity and Active Braking status are pro- • If the system turns off, and the instrument cluster dis- Changing the FCW status to “Only Warning” pre- grammable through the Uconnect system plays: vents the system from providing limited active brak- page 129.
Page 161 SAFETY • The TPMS will continue to warn the driver of low tire Driving on a significantly underinflated tire causes CAUTION! pressure as long as the condition exists, and will not the tire to overheat and can lead to tire failure. turn off until the tire pressure is at or above recom- Underinflation also reduces fuel efficiency and tire •...
Page 162: Service Tpms Warning
SAFETY Service TPMS Warning NOTE: It is particularly important for you to regularly check the The TPMS Warning Light will flash on and off for 75 tire pressure in all of your tires and to maintain the seconds, and remain on solid when a system fault is proper pressure page 260.
Page 163: Tpms Deactivation - If Equipped
SAFETY TPMS Deactivation — If Equipped NOTE: OCCUPANT RESTRAINT SYSTEMS There is no TPMS sensor in the spare tire. The TPMS The TPMS can be deactivated if replacing all four wheel will not be able to monitor the tire pressure. If you Some of the most important safety features in your and tire assemblies (road tires) with wheel and tire install the spare tire in place of a road tire that has a...
Page 164: Seat Belt Systems
SAFETY BeltAlert Warning Sequence 4. Never allow children to slide the shoulder belt SEAT BELT SYSTEMS behind them or under their arm. The BeltAlert warning sequence is activated when the Buckle up even though you are an excellent driver, even vehicle is moving above a specified vehicle speed range 5.
Page 165: Lap/Shoulder Belts
SAFETY NOTE: WARNING! WARNING! If BeltAlert has been deactivated and the driver or out- • • board front seat passenger (if equipped with outboard Do not allow people to ride in any area of your A seat belt that is buckled into the wrong buckle front passenger seat BeltAlert) is unbuckled the Seat vehicle that is not equipped with seats and seat will not protect you properly.
Page 166: Lap/Shoulder Belt Untwisting Procedure
SAFETY Lap/Shoulder Belt Operating 3. When the seat belt is long enough to fit, insert the 5. Position the shoulder belt across the shoulder and Instructions latch plate into the buckle until you hear a “click.” chest with minimal, if any slack so that it is comfort- able and not resting on your neck.
Page 167: Adjustable Upper Shoulder Belt Anchorage
SAFETY Adjustable Upper Shoulder Belt NOTE: WARNING! Anchorage The adjustable upper shoulder belt anchorage is equipped with an Easy Up feature. This feature allows • ONLY use a Seat Belt Extender if it is physically In the driver and outboard front passenger seats, the the shoulder belt anchorage to be adjusted in the required in order to properly fit the original seat top of the shoulder belt can be adjusted upward or...
Page 168: Seat Belt Pretensioner
SAFETY Energy Management Feature Seat belts must be worn by all occupants including pregnant women: the risk of injury in the event of an The front outboard seat belt system is equipped with an accident is reduced for the mother and the unborn child Energy Management feature that may help further if they are wearing a seat belt.
Page 169: Supplemental Restraint Systems (Srs)
SAFETY How To Engage The Automatic Locking Mode If the passenger seating position is equipped with an SUPPLEMENTAL RESTRAINT ALR and is being used for normal usage, only pull the 1. Buckle the combination lap and shoulder belt. SYSTEMS (SRS) seat belt webbing out far enough to comfortably wrap around the occupant’s mid-section so as to not activate 2.
Page 170: Air Bag Warning Light
SAFETY Air Bag Warning Light Front Air Bags NOTE: If the speedometer, tachometer, or any engine related The Occupant Restraint Controller (ORC) This vehicle has front air bags and lap/shoulder belts gauges are not working, the Occupant Restraint Control- monitors the readiness of the electronic for both the driver and front passenger.
Page 171: Driver And Passenger Front Air Bag Features
SAFETY Front Air Bag Operation This vehicle may be equipped with a driver and/or front WARNING! passenger seat belt buckle switch that detects whether Front Air Bags are designed to provide additional pro- the driver or front passenger seat belt is buckled. The •...
Page 172: Occupant Classification System (Ocs) - Front Passenger Seat
SAFETY Occupant Classification System (OCS) — Occupant Classification Module (OCM) And Sensor The OCS will NOT prevent deployment of the Passenger Front Passenger Seat Advanced Front Air Bag. The OCS may reduce the infla- The Occupant Classification Module (OCM) is located tion rate of the Passenger Advanced Front Air Bag if the underneath the front passenger seat.
Page 173 SAFETY Lighter Weight Passengers (Including Small Adults) • The OCS determines the front passenger’s most prob- Objects are lodged under the front passenger seat. able classification. The OCS estimates the seated • When a lighter weight passenger, including a small Objects are lodged between the front passenger weight on the front passenger seat and where that adult, occupies the front passenger seat, the OCS may...
Page 174 SAFETY WARNING! • Placing an object on the floor under the front pas- senger seat may prevent the OCS from working properly, which may result in serious injury or death in a collision. Do not place any objects on the floor under the front passenger seat. The Air Bag Warning Light in the instrument panel will turn on whenever the OCS is unable to classify the...
Page 175: Knee Impact Bolsters
SAFETY Knee Impact Bolsters The following requirements must be strictly followed: • Do not modify the front passenger seat assembly or The Knee Impact Bolsters help protect the knees of the components in any way. driver and front passenger, and position the front occu- •...
Page 176 SAFETY Supplemental Side Air Bag Inflatable Curtains The SABICs may help reduce the risk of partial or com- The Side Air Bags will not deploy in all side collisions, (SABICs) plete ejection of vehicle occupants through side win- including some collisions at certain angles, or some dows in certain side impact events.
Page 177: If A Deployment Occurs
SAFETY The SABICs may help reduce the risk of partial or com- If you do have a collision which deploys the air bags, WARNING! plete ejection of vehicle occupants through side win- any or all of the following may occur: dows in certain rollover or side impact events.
Page 178: Enhanced Accident Response System Reset Procedure
SAFETY ○ Maintaining Your Air Bag System NOTE: Electric park brake ○ Automatic transmission gear selector • ○ Air bag covers may not be obvious in the interior Horn WARNING! trim, but they will open during air bag deployment. ○ Front wiper •...
Page 179: Child Restraints
SAFETY Event Data Recorder (EDR) NOTE: CHILD RESTRAINTS This vehicle is equipped with an event data recorder • Everyone in your vehicle needs to be buckled up at all For additional information, refer to (EDR). The main purpose of an EDR is to record, in cer- http://www.nhtsa.gov/parents-and-caregivers or times, including babies and children.
Page 180: Summary Of Recommendations For Restraining Children In Vehicles
SAFETY Summary Of Recommendations For Restraining Children In Vehicles Child Size, Height, Weight Or Age Recommended Type Of Child Restraint Children who are two years old or younger and who have not Either an Infant Carrier or a Convertible Child Restraint, facing Infants and Toddlers reached the height or weight limits of their child restraint rearward in a rear seat of the vehicle...
Page 181: Recommendations For Attaching Child Restraints
SAFETY Children Too Large For Booster Seats If the answer to any of these questions was “no,” then WARNING! the child still needs to use a booster seat in this Children who are large enough to wear the shoulder vehicle. If the child is using the lap/shoulder belt, check •...
Page 182: Lower Anchors And Tethers For Children (Latch) Restraint System
SAFETY Lower Anchors And Tethers For CHildren LATCH Positions For Installing Child (LATCH) Restraint System Restraints In This Vehicle 60/40 Second Row LATCH Positions (7 Passenger) Lower Anchorage Symbol (2 Anchorages Per Seat- LATCH Label ing Position) Top Tether Anchorage Symbol 60/40 Second Row LATCH Positions (5 Passenger) Your vehicle is equipped with the child restraint anchor- age system called LATCH, which stands for Lower...
Page 183 SAFETY Frequently Asked Questions About Installing Child Restraints With LATCH Use the LATCH anchorage system until the combined weight of the What is the weight limit (child’s weight + weight of the child restraint) child and the child restraint is 65 lb (29.5 kg). Use the seat belt and 65 lb (29.5 kg) for using the LATCH anchorage system to attach the child restraint? tether anchor instead of the LATCH system once the combined...
Page 184: Locating The Latch Anchorages
SAFETY Locating The LATCH Anchorages The lower anchorages are round bars that are found at the rear of the seat cushion where it meets the seatback. They are just visible when you lean into the rear seat to install the child restraint. You will easily feel them if you run your finger along the gap between the seatback and seat cushion.
Page 185 SAFETY WARNING! • Never use the same lower anchorage to attach more than one child restraint. For typical installa- tion instructions, see page 184. Vehicle With A Center Arm Rest Tether — Five Or Seven Passenger Seating Only For rear-facing child restraints secured in the center seat position with the vehicle seat belts, the rear center seat position has an armrest tether that secures the Seven Passenger Top Tether Strap Mounting (2nd Row...
Page 186: To Install A Latch-Compatible Child Restraint
SAFETY How To Stow An Unused Switchable-ALR 2. Pull down on the tether to unhook it from the plastic 1. Loosen the adjusters on the lower straps and on the seat backing. tether strap of the child seat so that you can more (ALR) Seat Belt: easily attach the hooks or connectors to the vehicle When using the LATCH attaching system to install a...
Page 187: Installing Child Restraints Using The Vehicle Seat Belt
SAFETY Installing Child Restraints Using The Lap/Shoulder Belt Systems For Vehicle Seat Belt Installing Child Restraints In This Vehicle Child restraint systems are designed to be secured in vehicle seats by lap belts or the lap belt portion of a lap/shoulder belt.
Page 188: Installing A Child Restraint With A Switchable Automatic Locking Retractor (Alr)
SAFETY Frequently Asked Questions About Installing Child Restraints With Seat Belts What is the weight limit (child’s weight + weight of the child restraint) Always use the tether anchor when using the seat belt to install a for using the Tether Anchor with the seat belt to attach a forward- Weight limit of the Child Restraint forward-facing child restraint, up to the recommended weight limit of facing child restraint?
Page 189: Installing Child Restraints Using The Top Tether Anchorage
SAFETY Installing Child Restraints Using The Top Tether Anchorage WARNING! Do not attach a tether strap for a rear-facing car seat to any location in front of the car seat, including the seat frame or a tether anchorage. Only attach the tether strap of a rear-facing car seat to the tether anchorage that is approved for that seating position, located behind the top of the vehicle seat.
Page 190: Safety Tips
SAFETY WARNING! • The top tether anchorages are not visible until the gap panel is folded down. Do not use the visible cargo tie down hooks, located on the floor behind the seats, to attach a child restraint tether anchor. •...
Page 191: Transporting Pets
SAFETY Floor Mat Safety Information TRANSPORTING PETS SAFETY CHECKS YOU SHOULD MAKE INSIDE THE VEHICLE Always use floor mats designed to fit your vehicle. Only Air Bags deploying in the front seat could harm your use a floor mat that does not interfere with the opera- pet.
Page 192: Periodic Safety Checks You Should Make Outside The Vehicle
SAFETY PERIODIC SAFETY CHECKS YOU EXHAUST GAS WARNING! SHOULD MAKE OUTSIDE THE • ONLY use the driver’s side floor mat on the driver’s WARNING! VEHICLE side floor area. To check for interference, with the vehicle properly parked with the engine off, fully Exhaust gases can injure or kill.
Page 193: Carbon Monoxide Warnings
SAFETY CARBON MONOXIDE WARNINGS WARNING! Carbon monoxide (CO) in exhaust gases is deadly. Follow the precautions provided to prevent carbon monoxide poisoning: • Do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas, which can kill. Never run the engine in a closed area, such as a garage, and never sit in a parked vehicle with the engine running for an extended period.
Page 194: In Case Of Emergency
IN CASE OF EMERGENCY HAZARD WARNING FLASHERS SOS AND ASSIST MIRROR — IF EQUIPPED If equipped, the rearview mirror contains an SOS and ASSIST button. The Hazard Warning Flashers button is located on the NOTE: switch bank just below the climate controls. •...
Page 195 IN CASE OF EMERGENCY SOS Call System Limitations 3. Once a connection between the vehicle and an SOS WARNING! operator is made, the SOS Call system may transmit Vehicles sold in Mexico DO NOT have SOS Call system the following important vehicle information to an •...
Page 196: Jacking And Tire Changing - If Equipped
IN CASE OF EMERGENCY NOTE: Even if the SOS Call system is fully functional, factors CAUTION! beyond FCA US LLC’s control may prevent or stop the • Never place anything on or near the vehicle’s LTE SOS Call system operation. These include, but are not To avoid damage to the mirror during cleaning, never (voice/data), 4G (data) and GPS antennas.
Page 197: Preparations For Jacking
IN CASE OF EMERGENCY Lift up on the load floor handle to access the jack and WARNING! tools in the cargo area. • The jack is designed to be used as a tool for changing tires only. The jack should not be used to lift the vehicle for service purposes.
Page 198: Spare Tire Stowage - If Equipped
IN CASE OF EMERGENCY Rotate the plastic thumb screw on the end of the jack to loosen the jack and remove from the bracket. Spare Tire Location Winch Plug Location 3. Fit the jack handle extension over the drive nut. Use Jack Removal CAUTION! the lug wrench handle and extension to completely...
Page 199: Jacking Instructions - If Equipped
IN CASE OF EMERGENCY 4. Slide the tire out from under the vehicle and rotate it 6. Slide the metal stamping up the steel extension vertically behind the rear fascia/bumper. tube and winch cable. Rotate the metal stamping and push it through the hole and wheel. Winch Location Spare Tire Sleeve And Cable...
Page 200 IN CASE OF EMERGENCY 1. Loosen (but do not remove) the wheel lug nuts by 3. For the front tire, place the jack on the body flange WARNING! just behind the front tire. Do not raise the vehicle turning them to the left, one turn, while the wheel is until you are sure the jack is fully engaged.
Page 201 IN CASE OF EMERGENCY 4. For a rear tire, place the jack in the slot on the rear 5. Raise the vehicle by turning the jack screw clock- CAUTION! tie-down bracket, just forward of the rear tire. Do not wise. Raise the vehicle just enough to remove the raise the vehicle until you are sure the jack is fully flat tire.
Page 202: Jump Starting
IN CASE OF EMERGENCY NOTE: to the jack with the lug wrench on the forward side of the jack. Expand the jack on the bracket by turn- Double check to ensure the tire is snug against the ing the thumb screw clockwise until it is tight to underbody of the vehicle.
Page 203: Preparations For Jump Start
IN CASE OF EMERGENCY NOTE: CAUTION! WARNING! Be sure that the disconnected cable ends do not touch each other, or either vehicle, before properly connected • Do not use a portable battery booster pack or any Take care to avoid the radiator cooling fan when- for jump starting.
Page 204: Refueling In Emergency - If Equipped
IN CASE OF EMERGENCY Connecting The Jumper Cables Disconnecting The Jumper Cables REFUELING IN EMERGENCY – 1. Connect the positive (+) end of the jumper cable to 1. Disconnect the negative (-) end of the jumper cable IF EQUIPPED the remote positive (+) post of the discharged from the remote negative (-) post of the discharged vehicle.
Page 205: If Your Engine Overheats
IN CASE OF EMERGENCY WARNING! You or others can be badly burned by hot engine cool- ant (antifreeze) or steam from your radiator. If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.
Page 206: Manual Park Release
IN CASE OF EMERGENCY MANUAL PARK RELEASE 5. While the metal latch is in the open position, pull upward on the tether strap until the lever clicks and latches in the released position. The transmission is now out of PARK (P) and the vehicle can be moved. WARNING! Always secure your vehicle by fully applying the park- ing brake before activating the Manual Park Release.
Page 207: Freeing A Stuck Vehicle
IN CASE OF EMERGENCY NOTE: To Disengage The Manual Park Release Lever: WARNING! Be sure to replace the cover by snapping it back in 1. To disengage the Manual Park Release, apply ten- place. Fast spinning tires can be dangerous. Forces gener- sion upward while pushing the release latch towards ated by excessive wheel speeds may cause damage, the tether to unlock the lever.
Page 208: Towing A Disabled Vehicle
IN CASE OF EMERGENCY TOWING A DISABLED VEHICLE This section describes procedures for towing a disabled vehicle using a commercial towing service. If the transmission and drivetrain are operable, disabled 4x4 vehicles may also be towed as described under page 123. Towing Condition Wheels OFF The Ground Rear-Wheel Drive Models...
Page 209: All-Wheel Drive Models
IN CASE OF EMERGENCY CAUTION! CAUTION! • • Towing faster than 30 mph (48 km/h) or farther Front or rear wheel lifts must not be used (if the than 30 miles (48 km) with rear wheels on the remaining wheels are on the ground). Internal ground can cause severe transmission damage.
Page 210: Servicing And Maintenance
SERVICING AND MAINTENANCE Once A Month Or Before A Long Trip: SCHEDULED SERVICING influence when the “Oil Change Required” message is displayed. Have your vehicle serviced as soon as pos- • Check engine oil level sible, within the next 500 miles (805 km). Your vehicle is equipped with an automatic oil change •...
Page 211 SERVICING AND MAINTENANCE Mileage Or Time Passed (Whichever Comes First) Or Years: Or Kilometers: Additional Inspections Inspect the CV/Universal joints. Inspect front suspension, tie rod ends, and replace if necessary. Inspect the front and rear axle fluid, change if using your vehicle for police, taxi, fleet, off- road or frequent trailer towing.
Page 212 SERVICING AND MAINTENANCE Mileage Or Time Passed (Whichever Comes First) Or Years: Or Kilometers: Inspect accessory drive belt tensioner and pul- ley, replace if necessary. Change transfer case fluid - Normal Usage. Change transfer case fluid - Severe Usage (police, taxi, fleet, off-road or frequent trailer towing).
Page 213: Engine Compartment
SERVICING AND MAINTENANCE ENGINE COMPARTMENT 3.6L ENGINE 1 — Remote Jump Start Negative Terminal 6 — Brake Fluid Reservoir Cap 2 — Remote Jump Start Positive Terminal 7 — Engine Coolant Pressure Cap 3 — Power Distribution Center (Fuses) 8 — Washer Fluid Reservoir Cap 4 —...
Page 214: L Engine
SERVICING AND MAINTENANCE 5.7L ENGINE 1 — Remote Jump Start Negative Terminal 6 — Engine Coolant Reservoir Cap 2 — Remote Jump Start Positive Terminal 7 — Engine Coolant Pressure Cap 3 — Power Distribution Center (Fuses) 8 — Engine Oil Dipstick 4 —...
Page 215: Checking Oil Level
SERVICING AND MAINTENANCE CHECKING OIL LEVEL ADDING WASHER FLUID WARNING! To ensure proper engine lubrication, the engine oil must The instrument cluster display will indicate when the • Battery fluid is a corrosive acid solution and can be maintained at the correct level. Check the oil level at washer fluid level is low.
Page 216: Pressure Washing
SERVICING AND MAINTENANCE PRESSURE WASHING ENGINE OIL CAUTION! Cleaning the engine compartment with a high pressure Engine Oil Selection — Non-SRT Do not use chemical flushes in your engine oil as the washer is not recommended. chemicals can damage your engine. Such damage is Use only the manufacturer's recommended fluid not covered by the New Vehicle Limited Warranty.
Page 217: Engine Oil Filter
SERVICING AND MAINTENANCE Engine Air Cleaner Filter Inspection and ENGINE OIL FILTER Replacement The engine oil filter should be replaced with a new filter Engine Air Cleaner Filter Removal at every engine oil change. Engine Oil Filter Selection 1. Release the spring clips from the engine air cleaner A full-flow type disposable oil filter should be used for filter cover.
Page 218: Air Conditioner Maintenance
SERVICING AND MAINTENANCE Refrigerant Recovery And Recycling Cabin Air Filter AIR CONDITIONER MAINTENANCE R-134a — If Equipped For the proper maintenance intervals page 208. For best possible performance, your air conditioner should be checked and serviced by an authorized R-134a Air Conditioning Refrigerant is a Hydrofluoro- dealer at the start of each warm season.
Page 219: Accessory Drive Belt Inspection
SERVICING AND MAINTENANCE 2. There are glove compartment travel stops on both 5. Remove the filter cover by disengaging the retaining 8. Reinstall the glove compartment door on the door sides of the glove compartment door. Partially close tab and mid way snap that secures the filter cover to hinge and reattach the tension tether by inserting the glove compartment door and push inward to the HVAC housing.
Page 220: Body Lubrication
SERVICING AND MAINTENANCE When inspecting accessory drive belts, small cracks Some conditions can be caused by a faulty component WINDSHIELD WIPER BLADES that run across the ribbed surface of the belt from rib to such as a belt pulley. Belt pulleys should be carefully Clean the rubber edges of the wiper blades and the rib, are considered normal.
Page 221: Front Wiper Blade Removal/Installation
SERVICING AND MAINTENANCE Front Wiper Blade Removal/Installation 2. To disengage the wiper blade from the wiper arm, flip up the release tab on the wiper blade and while holding the wiper arm with one hand, slide the wiper CAUTION! blade down towards the base of the wiper arm. Do not allow the wiper arm to spring back against the glass without the wiper blade in place or the glass may be damaged.
Page 222: Rear Wiper Blade Removal/Installation
SERVICING AND MAINTENANCE Rear Wiper Blade Removal/Installation 2. Lift the rear wiper arm fully off the glass. 1. Lift the rear wiper arm pivot cap away from the glass to allow the rear wiper blade to be raised off of the glass.
Page 223: Exhaust System
SERVICING AND MAINTENANCE 3. Insert the wiper blade pivot pin into the opening on To minimize the possibility of catalytic converter CAUTION! the end of the wiper arm. Grab the bottom end of the damage: wiper arm with one hand, and press the wiper blade •...
Page 224: Engine Coolant Checks
SERVICING AND MAINTENANCE Engine Coolant Checks Selection Of Coolant Adding Coolant Check the engine coolant (antifreeze) protection every For further information page 255. Your vehicle has been built with an improved engine 12 months (before the onset of freezing weather, where coolant (OAT coolant conforming to MS.90032) that NOTE: applicable).
Page 225: Cooling System Pressure Cap
SERVICING AND MAINTENANCE Disposal Of Used Coolant • • Some vehicles require special tools to add coolant Maintain engine coolant concentration at a mini- properly. Failure to fill these systems properly could mum of 50% OAT coolant (conforming to MS.90032) Used ethylene glycol-based coolant (antifreeze) is a lead to severe internal engine damage.
Page 226: Fluid Level Check - Brake Master Cylinder
SERVICING AND MAINTENANCE Fluid Level Check — Brake Master Fluid Level Check WARNING! Cylinder The fluid level is preset at the factory and does not • Overfilling the brake fluid reservoir can result in require adjustment under normal operating conditions. The fluid level of the master cylinder should be checked spilling brake fluid on hot engine parts, causing Routine fluid level checks are not required;...
Page 227: Front/Rear Axle Fluid
SERVICING AND MAINTENANCE Fluid And Filter Changes FRONT/REAR AXLE FLUID TRANSFER CASE Under normal operating conditions, the fluid installed at For normal service, periodic fluid level checks are not Fluid Level Check the factory will provide satisfactory lubrication for the required.
Page 228: Fuses
SERVICING AND MAINTENANCE Underhood Fuses FUSES The fuses protect electrical systems against excessive current. The Power Distribution Center is located in the engine General Information When a device does not work, you must check the fuse compartment near the battery jump start posts. This element inside the blade fuse for a break/melt.
Page 229 SERVICING AND MAINTENANCE Power Distribution Center Location Cavity Cartridge Fuse Micro Fuse Description * If Equipped – – Spare – – Spare 60 Amp Yellow – Rad Fan *...
Page 230 SERVICING AND MAINTENANCE Cavity Cartridge Fuse Micro Fuse Description * If Equipped 60 Amp Yellow – ESP Pump Non-SRT 40 Amp Green – Air Suspension Comp * 40 Amp Green – ABS Pump SRT 30 Amp Pink – Starter Solenoid –...
Page 231 SERVICING AND MAINTENANCE Cavity Cartridge Fuse Micro Fuse Description * If Equipped 30 Amp Pink – DTCM – – Spare 30 Amp Pink – ELSD * 30 Amp Pink – Sunroof * 30 Amp Pink – 25 Amp Clear – HVAC RR Blower MTR * 30 Amp Pink –...
Page 232 SERVICING AND MAINTENANCE Cavity Cartridge Fuse Micro Fuse Description * If Equipped – 15 Amp Blue – 10 Amp Red PM Sensor * – 10 Amp Red A/C Clutch – 20 Amp Yellow Ignition Coils */ Ignition Coil Capacitors* – 25 Amp Clear Fuel Injectors / ECM –...
Page 233 SERVICING AND MAINTENANCE Cavity Cartridge Fuse Micro Fuse Description * If Equipped – 15 Amp Blue Cluster / CSG * / ITBM * – – Spare – – Spare – 20 Amp Yellow Pwr Outlet Cargo Area – 10 Amp Red Rr Console Lamp * / RR Pwr Outlet –...
Page 234: Bulb Replacement
SERVICING AND MAINTENANCE BULB REPLACEMENT Replacement Bulbs, Names, And Part Numbers In the instance a bulb needs to be replaced, this section includes bulb description and replacement part numbers. NOTE: See an authorized dealer for LED bulb replacement. Interior Bulbs Bulb Name Bulb Number Glove Compartment Lamp...
Page 235 SERVICING AND MAINTENANCE Exterior Bulbs Bulb Name Bulb Number Rear Stop/Turn Signal Lamps Rear Liftgate Tail Lamps Rear Backup Lamps 921 (W16W) Rear License Lamps Center High Mounted Stop Lamp (CHMSL) Bulb Replacement FRONT FOG LAMPS CENTER HIGH MOUNTED STOP LAMP (CHMSL) The front fog lamps are LEDs.
Page 236: Tires
SERVICING AND MAINTENANCE NOTE: TIRES • P (Passenger) — Metric tire sizing is based on US design standards. P-Metric tires have the letter “P” TIRE SAFETY INFORMATION molded into the sidewall preceding the size designa- Tire safety information will cover aspects of the follow- tion.
Page 237 SERVICING AND MAINTENANCE TIRE SIZING CHART EXAMPLE: Example Size Designation: P215/65R15XL 95H, 215/65R15 96H, LT235/85R16C, T145/80D18 103M, 31x10.5 R15 LT P = Passenger car tire size based on US design standards, or "..blank.." = Passenger car tire based on European design standards, or LT = Light truck tire based on US design standards, or T or S = Temporary spare tire or 31 = Overall diameter in inches (in)
Page 238: Tire Identification Number (Tin)
SERVICING AND MAINTENANCE Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire; however, the date code may only be on one side. Tires with white sidewalls will have the full TIN, including the date code, located on the white sidewall side of the tire.
Page 239: Tire Loading And Tire Pressure
SERVICING AND MAINTENANCE Tire Loading And Tire Pressure This placard tells you important information about the: 1. Number of people that can be carried in the vehicle. NOTE: 2. Total weight your vehicle can carry. The proper cold tire inflation pressure is listed on the driver’s side B-pillar or the rear edge of the driver's side 3.
Page 240 SERVICING AND MAINTENANCE Steps For Determining Correct Load (6) If your vehicle will be towing a Limit— trailer, load from your trailer will be transferred to your vehicle. Consult (1) Locate the statement “The com- this manual to determine how this bined weight of occupants and cargo reduces the available cargo and lug- should never exceed XXX kg or...
Page 241 SERVICING AND MAINTENANCE WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them.
Page 242: Tires - General Information
SERVICING AND MAINTENANCE TIRES — GENERAL INFORMATION Both underinflation and overinflation affect the stability CAUTION! of the vehicle and can produce a feeling of sluggish Tire Pressure response or over responsiveness in the steering. After inspecting or adjusting the tire pressure, always reinstall the valve stem cap.
Page 243: Tire Pressures For High Speed Operation
SERVICING AND MAINTENANCE Tire Pressures For High Speed Operation Tire Repair It is not recommended driving a vehicle loaded at full capacity or to tow a trailer while a tire is in the Run Flat If your tire becomes damaged, it may be repaired if it The manufacturer advocates driving at safe speeds and mode.
Page 244: Tread Wear Indicators
SERVICING AND MAINTENANCE Tread Wear Indicators • Distance driven It is recommended to replace the two front tires or two rear tires as a pair. Replacing just one tire can seriously • Performance tires, tires with a speed rating of V or Tread wear indicators are in the original equipment affect your vehicle’s handling.
Page 245: Tire Types
SERVICING AND MAINTENANCE SPARE TIRES — IF EQUIPPED CAUTION! WARNING! NOTE: Replacing original tires with tires of a different size Do not use Summer tires in snow/ice conditions. You may result in false speedometer and odometer could lose vehicle control, resulting in severe injury or For vehicles equipped with Tire Service Kit instead of a readings.
Page 246: Collapsible Spare Tire - If Equipped
SERVICING AND MAINTENANCE Limited Use Spare — If Equipped tire. Compact spare tire descriptions begin with the let- Since this tire has limited tread life, the original equip- ter “T” or “S” preceding the size designation. Example: ment tire should be repaired (or replaced) and rein- The limited use spare tire is for temporary emergency T145/80D18 103M.
Page 247: Wheel And Wheel Trim Care
SERVICING AND MAINTENANCE WHEEL AND WHEEL TRIM CARE SNOW TRACTION DEVICES CAUTION! All wheels and wheel trim, especially aluminum and Use of traction devices require sufficient tire-to-body Do not use scouring pads, steel wool, a bristle brush, chrome plated wheels, should be cleaned regularly clearance.
Page 248 SERVICING AND MAINTENANCE Snow Traction Device (Maximum Pro- Axle Tire/Wheel Size jection Beyond Tire Profile Or Trim Level Equivalent) SPECIAL SERVICE P265/60R18 265/60R18 265/50R20 Rear THULE XG-12 PRO or Equivalent 265/50R20 CITADEL Snow Traction Device (Maximum Pro- Axle Tire/Wheel Size jection Beyond Tire Profile Or Trim Level Equivalent)
Page 249: Tire Rotation Recommendations
SERVICING AND MAINTENANCE TIRE ROTATION CAUTION! RECOMMENDATIONS To avoid damage to your vehicle or tires, observe the The tires on the front and rear of your vehicle operate following precautions: • at different loads and perform different steering, han- Because of restricted traction device clearance dling, and braking functions.
Page 250: Treadwear
SERVICING AND MAINTENANCE TREADWEAR 109. Grades B and A represent higher WARNING! levels of performance on the labora- The Treadwear grade is a comparative The traction grade assigned to this tory test wheel, than the minimum rating, based on the wear rate of the tire is based on straight-ahead brak- required by law.
Page 251: Bodywork
SERVICING AND MAINTENANCE • BODYWORK BODY AND UNDERBODY Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint MAINTENANCE finish. PROTECTION FROM ATMOSPHERIC Cleaning Headlights AGENTS CAUTION! Your vehicle is equipped with plastic headlights and fog •...
Page 252: Interiors
SERVICING AND MAINTENANCE INTERIORS PLASTIC AND COATED PARTS avoid soaking your leather upholstery with any liquid. Please do not use polishes, oils, cleaning fluids, sol- Use Mopar® Total Clean to clean vinyl upholstery. vents, detergents, or ammonia-based cleaners to clean SEATS AND FABRIC PARTS your leather upholstery.
Page 253: Technical Specifications
TECHNICAL SPECIFICATIONS VEHICLE IDENTIFICATION NUMBER (VIN) In the event power assist is lost for any reason (i.e., repeated brake applications with the engine off) the brakes will still function. However, the effort required to The VIN is found on a label located on the left front cor- brake the vehicle will be much greater than that ner of the instrument panel pad, visible from outside of required with the power system operating.
Page 254: Fuel Requirements
TECHNICAL SPECIFICATIONS 3.6L ENGINE MATERIALS ADDED TO FUEL Do not use E-85 flex fuel or ethanol blends greater than Besides using unleaded gasoline with the proper 15% in this engine. octane rating, gasolines that contain detergents, corro- sion and stability additives are recommended. Using This engine is designed to meet all emis- gasolines that have these additives will help improve sions regulations and provide optimum fuel...
Page 255: Gasoline/Oxygenate Blends
TECHNICAL SPECIFICATIONS GASOLINE/OXYGENATE BLENDS CNG AND LP FUEL SYSTEM FUEL SYSTEM CAUTIONS MODIFICATIONS Some fuel suppliers blend unleaded gasoline with oxy- genates such as ethanol. CAUTION! Modifications that allow the engine to run on Com- pressed Natural Gas (CNG) or Liquid Propane (LP) may CAUTION! Follow these guidelines to maintain your vehicle’s result in damage to the engine, emissions, and fuel...
Page 256: Fluid Capacities - Non-Srt
TECHNICAL SPECIFICATIONS FLUID CAPACITIES — NON-SRT Metric Fuel (Approximate) 3.6L and 5.7L Engines 24.6 gal 93 L Engine Oil With Filter 3.6L Engine 6 qt 5.6 L 5.7L Engine 7 qt 6.6 L Cooling System * 3.6L Engine – Without Trailer Tow Package 10.4 qt 9.9 L 3.6L Engine –...
Page 257: Engine Fluids And Lubricants - Non-Srt
TECHNICAL SPECIFICATIONS ENGINE FLUIDS AND LUBRICANTS — NON-SRT Component Fluid, Lubricant, or Genuine Part We recommend using Mopar® Antifreeze/Coolant 10 Year/150,000 Mile Engine Coolant (240,000 km) Formula OAT (Organic Additive Technology) meeting the requirements of the manufacturer Material Standard MS.90032. We recommend using Mopar®...
Page 258: Customer Assistance
CUSTOMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE IF YOU NEED ASSISTANCE ROADSIDE ASSISTANCE Available 24 hours, 7 days a week. FOR YOUR VEHICLE FCA US LLC and its authorized dealers are vitally inter- Call 1-800-521-2779 or visit chrysler.rsahelp.com(USA) ested in your satisfaction. We want you to be happy with Call 1-800-363-4869 or visit fca.roadsideaid.com our products and services.
Page 259: Fca Us Llc Customer Center
(TDD/TTY) FCA US LLC reserves the right to modify the terms or closest authorized Chrysler, Dodge, Jeep®, or Ram discontinue the Roadside Assistance Program at any dealer. If you choose to go to another dealer, you will be To assist customers who have hearing difficulties, FCA time.
Page 260: Service Contract
CUSTOMER ASSISTANCE SERVICE CONTRACT We appreciate that you have made a major investment REPORTING SAFETY DEFECTS when you purchased the vehicle. An authorized dealer You may have purchased a service contract for a has also made a major investment in facilities, tools, vehicle to help protect you from the high cost of unex- IN THE 50 UNITED STATES AND and training to assure that you are absolutely delighted...
Page 261: In Canada
CUSTOMER ASSISTANCE PUBLICATION ORDER FORMS Change Of Ownership Or Address To contact NHTSA, you may call the Vehicle Safety Hotline toll free at To order the following manuals, you may use either the *If you have purchased this vehicle used or have 1-888-327-4236 (TTY: website or the phone numbers listed below.
Page 262: General Information
CUSTOMER ASSISTANCE General Information The following regulatory statement applies to all Radio Frequency (RF) devices equipped in this vehicle: This device complies with Part 15 of the FCC Rules and with Innovation, Science and Economic Development Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: 1.
Page 263 INDEX Air Conditioning System ....51 Auxiliary Power Outlet ....56 Air Filter..... .215 Axle Fluid .
Page 264 INDEX Cargo Area Cover ....63 Disposal Of Used Coolant ...223 Anti-Lock Brake System ... .149 Cargo Compartment .
Page 265 INDEX Fueling ..... .114 Fuses ..... . .226 Filters Ignition .
Page 266 INDEX Air Bag ....75, 168, 189 Side Marker ....233 Automatic Headlights .
Page 267 INDEX Exterior Folding ....36 Oil Filter, Change ....215 Pregnant Women And Seat Belts .
Page 268 INDEX Remote Starting System ....17 Pretensioners ....166 Resume ....98 Replacement Bulbs .
Page 269 INDEX Tire And Loading Information Placard ..237 Towing Behind A Motorhome... .123 Tire Markings ....234 Tow N Go .

Dodge DURANGO 2023 Owner's Manual

Quick Links

Need help?

Questions and answers

Related Manuals for Dodge DURANGO 2023

Summary of Contents for Dodge DURANGO 2023