Page 1 Durango 2 0 1 8 O W N E R ’ S M A N U A L...
Page 2 VEHICLES SOLD IN CANADA This manual illustrates and describes the operation of With respect to any Vehicles Sold in Canada, the name features and equipment that are either standard or op- FCA US LLC shall be deemed to be deleted and the name tional on this vehicle.
Page 3: Table Of Contents
TABLE OF CONTENTS SECTION PAGE INTRODUCTION ..............3 GRAPHICAL TABLE OF CONTENTS .
Page 5: Introduction
INTRODUCTION CONTENTS INTRODUCTION ......4 ▫ Symbols .......6 ROLLOVER WARNING .
Page 6: Introduction
4 INTRODUCTION INTRODUCTION This Owner’s Manual has been prepared with the assis- tance of service and engineering specialists to acquaint you Dear Customer, congratulations on selecting your new with the operation and maintenance of your vehicle. It is vehicle. Be assured that it represents precision workman- supplemented by Warranty Information, and customer ship, distinctive styling, and high quality.
Page 7: Rollover Warning
INTRODUCTION reason, it reserves the right to make changes to the model Do not attempt sharp turns, abrupt maneuvers, or other described for technical and/or commercial reasons. For unsafe driving actions that can cause loss of vehicle con- further information, contact an authorized dealer. trol.
Page 8: Symbols
6 INTRODUCTION HOW TO USE THIS MANUAL The detailed index at the back of this Owner’s Manual contains a complete listing of all subjects. Essential Information Symbols Consult the Table of Contents to determine which section contains the information you desire. Consult the following table for a description of the symbols that may be used on your vehicle or throughout this Since the specification of your vehicle depends on the items...
Page 9: Warnings And Cautions
INTRODUCTION WARNINGS AND CAUTIONS This Owner’s Manual contains WARNINGS against oper- ating procedures that could result in a collision, bodily injury and/or death. It also contains CAUTIONS against procedures that could result in damage to your vehicle. If you do not read this entire Owner’s Manual, you may miss important information.
Page 11: Graphical Table Of Contents
GRAPHICAL TABLE OF CONTENTS CONTENTS FRONT VIEW ......10 INSTRUMENT PANEL .....12 REAR VIEW.
Page 12 10 GRAPHICAL TABLE OF CONTENTS FRONT VIEW Front View 1 — Doors 4 — Wheels/Tires 2 — Exterior Mirrors 5 — Hood/Engine Compartment 3 — Windshield 6 — Headlights...
Page 13 GRAPHICAL TABLE OF CONTENTS 11 REAR VIEW Rear View 1 — Rear Lights 2 — Rear Windshield Wiper 3 — Liftgate...
Page 14 12 GRAPHICAL TABLE OF CONTENTS INSTRUMENT PANEL Instrument Panel 1 — Air Vents 4 — Instrument Cluster 2 — Paddle Shifter (–) 5 — Paddle Shifter (+) 3 — Steering Wheel 6 — Radio...
Page 15 GRAPHICAL TABLE OF CONTENTS 13 INTERIOR Interior 1 — Door Locks/Window Switches 4 — Climate Controls 2 — Seats 5 — Switch Panel 3 — Gear Selector 6 — Glove Compartment...
Page 17 GETTING TO KNOW YOUR VEHICLE CONTENTS KEYS ....... . .20 ▫...
Page 18 16 GETTING TO KNOW YOUR VEHICLE ▫ Automatic Unlock On Exit Feature — HEAD RESTRAINTS ..... .64 If Equipped ......42 ▫...
Page 19: Windshield
GETTING TO KNOW YOUR VEHICLE 17 ▫ Heated Mirrors — If Equipped ... . .75 ▫ Turn Signals ......80 ▫...
Page 20 18 GETTING TO KNOW YOUR VEHICLE ▫ Wind Buffeting ......111 GARAGE DOOR OPENER — IF EQUIPPED ..120 POWER SUNROOF —...
Page 21 GETTING TO KNOW YOUR VEHICLE 19 ROOF LUGGAGE RACK — IF EQUIPPED ..139 ▫ Stowing The Crossbars ....143 ▫...
Page 22: Keys
20 GETTING TO KNOW YOUR VEHICLE KEYS To remove the emergency key, slide the mechanical latch at the top of the key fob sideways with your thumb and then Key Fob pull the key out with your other hand. Your vehicle uses a keyless ignition system. The ignition system consists of a key fob with Remote Keyless Entry (RKE) and a START/STOP push button ignition system.
Page 23 GETTING TO KNOW YOUR VEHICLE 21 To Unlock The Doors And Liftgate Push the interior door unlock button on the door panel. Push and release the unlock button on the key fob once to unlock the driver’s door or twice within five seconds to unlock all doors and the liftgate.
Page 24 22 GETTING TO KNOW YOUR VEHICLE To Lock The Doors And Liftgate Replacing The Battery In The Key With Remote Control Push and release the lock button on the key fob to lock all doors and liftgate. The recommended replacement battery is one CR2032 battery.
Page 25 GETTING TO KNOW YOUR VEHICLE 23 2. Separate the key fob halves using the tip of the emer- gency key, a #2 flat blade screwdriver, or a coin and gently pry the two halves of the key fob apart. Make sure not to damage the seal during removal.
Page 26 24 GETTING TO KNOW YOUR VEHICLE Separating Case With A Coin Key Fob Battery Replacement 3. Remove the battery by turning the back cover over (battery facing downward) and tapping it lightly on a solid surface such as a table or similar and replace the battery.
Page 27 GETTING TO KNOW YOUR VEHICLE 25 Programming Additional Key Fobs General Information Programming the key fob may be performed by an autho- The following regulatory statement applies to all radio rized dealer. frequency (RF) devices equipped in this vehicle: Request For Additional Remote Controls This device complies with Part 15 of the FCC Rules and with Industry Canada license-exempt RSS standard(s).
Page 28: Ignition Switch
26 GETTING TO KNOW YOUR VEHICLE IGNITION SWITCH NOTE: In case the ignition switch does not change with the push of a button, the key fob may have a low or dead Keyless Push Button Ignition battery. In this situation, a back up method can be used to This feature allows the driver to operate the ignition with operate the ignition switch.
Page 29 GETTING TO KNOW YOUR VEHICLE 27 WARNING! WARNING! (Continued) ignition of a vehicle equipped with Keyless Enter- • Before exiting a vehicle, always shift the automatic N-Go in the ACC or ON/RUN mode. A child could transmission into PARK and apply the parking operate power windows, other controls, or move the brake.
Page 30: Dead Key Fob Battery
28 GETTING TO KNOW YOUR VEHICLE Dead Key Fob Battery REMOTE START — IF EQUIPPED Key Not Detected Feature How To Use Remote Start If the ignition position does not change with a push of the ignition button, and the instrument cluster display message This system uses the key fob to start the engine “Key Fob Not Detected”...
Page 31: Remote Start Abort Message - If Equipped
GETTING TO KNOW YOUR VEHICLE 29 Remote Start Abort Message — If Equipped • Battery at an acceptable charge level • PANIC button not pushed The following messages will display in the instrument cluster display if the vehicle fails to remote start or exits •...
Page 32: To Exit Remote Start Mode Without Driving The Vehicle
30 GETTING TO KNOW YOUR VEHICLE To Exit Remote Start Mode And Drive The Vehicle NOTE: • If an engine fault is present or fuel level is low, the Before the end of 15-minute cycle, push and release the vehicle will start and then shut down in 10 seconds. unlock button on the key fob to unlock the doors, or unlock the vehicle using Keyless Enter-N-Go —...
Page 33: General Information
GETTING TO KNOW YOUR VEHICLE 31 General Information The system uses a key fob and a Keyless Push Button Ignition, and a RF receiver to prevent unauthorized vehicle The following regulatory statement applies to all radio operation. Therefore, only key fobs that are programmed to frequency (RF) devices equipped in this vehicle: the vehicle can be used to start and operate the vehicle.
Page 34: Customer Key Programming
32 GETTING TO KNOW YOUR VEHICLE CAUTION! CAUTION! (Continued) • For vehicles equipped with Keyless Enter-N-Go — The Sentry Key Immobilizer system is not compatible Ignition, always remember to place the ignition in with some aftermarket remote starting systems. Use of the OFF position.
Page 35: Vehicle Security Alarm - If Equipped
GETTING TO KNOW YOUR VEHICLE 33 NOTE: Changes or modifications not expressly approved 2. Perform one of the following methods to lock the by the party responsible for compliance could void the vehicle: user’s authority to operate the equipment. • Push lock on the interior power door lock switch with the driver and/or passenger door open.
Page 36: To Disarm The System
34 GETTING TO KNOW YOUR VEHICLE To Disarm The System • The vehicle security alarm remains armed during power liftgate entry. Pushing the liftgate button will not disarm The vehicle security alarm can be disarmed using any of the vehicle security alarm. If someone enters the vehicle the following methods: through the liftgate and opens any door, the alarm will •...
Page 37: Rearming Of The System
GETTING TO KNOW YOUR VEHICLE 35 Rearming Of The System If something triggers the alarm, and no action is taken to disarm it, the vehicle security alarm will turn the horn off after 29 seconds, five seconds between cycles, up to eight cycles if the trigger remains active and the vehicle security alarm will rearm itself.
Page 38: Power Door Locks
36 GETTING TO KNOW YOUR VEHICLE WARNING! (Continued) • Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking brake, brake pedal or the gear selector.
Page 39: Keyless Enter-N-Go - Passive Entry
GETTING TO KNOW YOUR VEHICLE 37 If a rear door is locked, it cannot be opened from inside the • If the vehicle is unlocked by Passive Entry and no door vehicle without first unlocking the door. The door may be is opened within 60 seconds, the vehicle will re-lock and unlocked manually by raising the lock knob.
Page 40 38 GETTING TO KNOW YOUR VEHICLE To Unlock From The Driver’s Side: To Unlock From The Passenger Side: With a valid Passive Entry key fob within 5 ft (1.5 m) of the With a valid Passive Entry key fob within 5 ft (1.5 m) of the driver’s door handle, grab the driver’s front door handle to passenger door handle, grab the front passenger door unlock the driver’s door automatically.
Page 41 GETTING TO KNOW YOUR VEHICLE 39 vehicle’s Passive Entry key fob is detected inside the vehicle, and no other valid Passive Entry key fob are detected outside the vehicle, the Passive Entry System automatically unlocks all vehicle doors and chirps the horn three times (on the third attempt, ALL doors will lock, and the Passive Entry key fob can be locked in the vehicle).
Page 42 40 GETTING TO KNOW YOUR VEHICLE NOTE: If “Unlock All Doors 1st Press” is programmed in Uconnect Settings, all doors will unlock when you push the button on the liftgate. If Unlock Driver Door 1st Press is programmed in Uconnect Settings, the liftgate will unlock when you push the button on the liftgate.
Page 43 GETTING TO KNOW YOUR VEHICLE 41 NOTE: Do NOT grab the door handle, when pushing the • The Passive Entry system will not operate if the key fob door handle button. This could unlock the door(s). battery is dead. • Closeness to mobile devices can have an effect on the passive entry system.
Page 44: Automatic Unlock On Exit Feature - If Equipped
42 GETTING TO KNOW YOUR VEHICLE Automatic Unlock On Exit Feature — If Equipped To Engage Or Disengage The Child Protection Door Lock System If Auto Unlock is enabled, this feature will unlock all the doors when any door is opened if the vehicle is stopped 1.
Page 45: Seats
GETTING TO KNOW YOUR VEHICLE 43 SEATS Seats are a part of the Occupant Restraint System of the vehicle. WARNING! • It is dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed.
Page 46: Manual Adjustment (Front Seats)
44 GETTING TO KNOW YOUR VEHICLE Manual Adjustment (Front Seats) WARNING! • Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be adjusted properly and you could be injured.
Page 47 GETTING TO KNOW YOUR VEHICLE 45 WARNING! • Adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death. • Seats should be adjusted before fastening the seat belts and while the vehicle is parked.
Page 48 46 GETTING TO KNOW YOUR VEHICLE Front Passenger Seat Fold-Flat Feature — If WARNING! Equipped • Adjusting a seat while the vehicle is moving is To fold the seatback to the flat load-floor position, lift the dangerous. The sudden movement of the seat could recline lever and push the seatback forward.
Page 49: Power Adjustment (Front Seats) - If Equipped
GETTING TO KNOW YOUR VEHICLE 47 Power Adjustment (Front Seats) — If Equipped Adjusting The Seat Forward Or Rearward Some models may be equipped with eight-way power The seat can be adjusted both forward and rearward. Push driver and front passenger seats. The power seat switches the seat switch forward or rearward.
Page 50 48 GETTING TO KNOW YOUR VEHICLE Power Lumbar — If Equipped WARNING! Vehicles equipped with power driver or passenger seats • Adjusting a seat while driving may be dangerous. may also be equipped with power lumbar. The power Moving a seat while driving could result in loss of lumbar switch is located on the outboard side of the power control which could cause a collision and serious seat.
Page 51: Power Passenger Seat Adjustment - If Equipped
GETTING TO KNOW YOUR VEHICLE 49 Power Passenger Seat Adjustment — If Equipped Reclining The Seatback Some models are equipped with a six-way power passen- The angle of the seatback can be adjusted forward or ger seat. The power seat switch is located on the outboard rearward.
Page 52: Driver Memory Seat - If Equipped
50 GETTING TO KNOW YOUR VEHICLE CAUTION! (Continued) controls. Seat travel may become limited if movement is stopped by an obstruction in the seat’s path. Driver Memory Seat — If Equipped This feature allows the driver to store up to two different memory profiles for easy recall through a memory switch.
Page 53 GETTING TO KNOW YOUR VEHICLE 51 3. Push and release the set (S) button on the memory To program your key fobs, perform the following: switch. 1. Cycle the vehicle’s ignition to the OFF position. 4. Within five seconds, push and release either of the 2.
Page 54 52 GETTING TO KNOW YOUR VEHICLE Memory Position Recall driver’s seat and steering column (if equipped) stop mov- ing. A delay of one second will occur before another recall NOTE: The vehicle must be in PARK to recall memory can be selected. positions.
Page 55: Heated Seats - If Equipped
GETTING TO KNOW YOUR VEHICLE 53 Each stored memory setting will have an associated Easy WARNING! (Continued) Entry and Easy Exit position. • Do not place anything on the seat or seatback that NOTE: The Easy Entry/Exit feature is not enabled when insulates against heat, such as a blanket or cushion.
Page 56 54 GETTING TO KNOW YOUR VEHICLE If the HI-level setting is selected, the system will automati- WARNING! cally switch to LO-level after approximately 60 minutes of continuous operation. At that time, the display will change • Persons who are unable to feel pain to the skin from HI to LO, indicating the change.
Page 57 GETTING TO KNOW YOUR VEHICLE 55 Rear Heated Seats — If Equipped Push the switch once to select HI-level heating. Push the switch a second time to select LO-level On some models, the two rear outboard seats may be heating. Push the switch a third time to shut the equipped with heated seats.
Page 58: Front Ventilated Seats - If Equipped
56 GETTING TO KNOW YOUR VEHICLE • Press the ventilated seat button a third time to turn WARNING! (Continued) the ventilated seat off. • Do not place anything on the seat or seatback that NOTE: The engine must be running for the ventilated seats insulates against heat, such as a blanket or cushion.
Page 59: 60/40 Split Rear Seat
GETTING TO KNOW YOUR VEHICLE 57 60/40 Split Rear Seat Second Row Fold Flat Seat The second row seats can be folded flat to carry cargo. Pull upward on the release lever located on the outboard side of the seat. Fold-Flat Second Row Seat NOTE: You may experience deformation in the seat cush- ion from the seat belt buckles if the seats are left folded for...
Page 60 58 GETTING TO KNOW YOUR VEHICLE Easy Access For Third Row 2. Tumble the seat forward using the pull strap located behind the seatback. Either side of the rear seat can be tumbled forward to allow passengers to easily access the third row seats. 1.
Page 61 GETTING TO KNOW YOUR VEHICLE 59 To Raise Rear Seat Fold the seat rearward to it’s original position, and lock it into place. WARNING! Be certain that the seatback is securely locked into position. If the seatback is not securely locked into position the seat will not provide the proper stability for child seats and/or passengers.
Page 62: Rear Captain's Chairs - If Equipped
60 GETTING TO KNOW YOUR VEHICLE Rear Captain’s Chairs — If Equipped Second Row Captain Chair Fold Flat Seats The second row seats can be folded flat to carry cargo. Pull upward on the release lever located on the outboard side of the seat.
Page 63 GETTING TO KNOW YOUR VEHICLE 61 Easy Access For Third Row Either side of the rear seat can be tumbled forward to allow passengers to easily access the third row seats. 1. Pull upward on the release lever to release the seat. Tumble Strap WARNING! Do not drive the vehicle with the second row seats in...
Page 64 62 GETTING TO KNOW YOUR VEHICLE 3. If your vehicle is equipped with a mini console, there is To Raise Rear Seat a stepping pad to allow passengers to easily access the Fold the seat rearward to it’s original position, and lock it third row seats.
Page 65: Folding Third Row
GETTING TO KNOW YOUR VEHICLE 63 Folding Third Row Both third row seats can be folded forward to increase the cargo area. To lower either seat, pull on the release handle located on back of the seat and lower the seat using the pull strap located next to the release handle.
Page 66: Head Restraints
64 GETTING TO KNOW YOUR VEHICLE WARNING! WARNING! (Continued) • Head restraints should never be adjusted while the Be certain that the seatback is securely locked into vehicle is in motion. Driving a vehicle with the head position. If the seatback is not securely locked into restraints improperly adjusted or removed could position the seat will not provide the proper stability cause serious injury or death in the event of a...
Page 67 GETTING TO KNOW YOUR VEHICLE 65 To raise the head restraint, pull upward on the head For comfort the Active Head Restraints can be tilted restraint. To lower the head restraint, push the adjustment forward and rearward. To tilt the head restraint closer to button, located at the base of the head restraint, and push the back of your head, pull forward on the bottom of the downward on the head restraint.
Page 68 66 GETTING TO KNOW YOUR VEHICLE WARNING! • All occupants, including the driver, should not oper- ate a vehicle or sit in a vehicle’s seat until the head restraints are placed in their proper positions in order to minimize the risk of neck injury in the event of a collision.
Page 69: Head Restraints - Rear Seats
GETTING TO KNOW YOUR VEHICLE 67 Head Restraints — Rear Seats WARNING! The head restraints on the outboard seats are not adjust- Sitting in a seat with the head restraint in its lowered able. They automatically fold forward when the rear seat is position could result in serious injury or death in a folded to a load floor position, but do not return to their collision.
Page 70: Power Folding Third Row Head Restraints
68 GETTING TO KNOW YOUR VEHICLE NOTE: For proper routing of a Child Seat Tether, refer to WARNING! “Occupant Restraints” in “Safety” for further information. • ALL the head restraints MUST be reinstalled in the WARNING! vehicle to properly protect the occupants. Follow the re-installation instructions above prior to operating •...
Page 71: Steering Wheel
GETTING TO KNOW YOUR VEHICLE 69 NOTE: • The head restraints can only be folded downward using the Headrest Fold button. The head restraints must be raised manually when occupying the third row. • Do not fold if there are passengers seated in the third row seats.
Page 72: Power Tilt/Telescoping Steering Column - If Equipped
70 GETTING TO KNOW YOUR VEHICLE WARNING! Do not adjust the steering column while driving. Adjusting the steering column while driving or driv- ing with the steering column unlocked, could cause the driver to lose control of the vehicle. Failure to follow this warning may result in serious injury or death.
Page 73: Heated Steering Wheel - If Equipped
GETTING TO KNOW YOUR VEHICLE 71 The heated steering wheel control button is located within WARNING! the Uconnect system. You can gain access to the control button through the climate screen or the controls screen. Do not adjust the steering column while driving. Adjusting the steering column while driving or driv- •...
Page 74: Mirrors
72 GETTING TO KNOW YOUR VEHICLE MIRRORS Vehicles Equipped With Remote Start On models that are equipped with remote start, the heated Inside Day/Night Mirror — If Equipped steering wheel can be programmed to come on during a The mirror head can be adjusted up, down, left, and right remote start through the Uconnect system.
Page 75: Automatic Dimming Mirror - If Equipped
GETTING TO KNOW YOUR VEHICLE 73 Automatic Dimming Mirror — If Equipped The mirror head can be adjusted up, down, left, and right for various drivers. The mirror should be adjusted to center on the view through the rear window. This mirror automatically adjusts for headlight glare from vehicles behind you.
Page 76: Outside Automatic Dimming Mirrors - If
74 GETTING TO KNOW YOUR VEHICLE The power mirror controls consist of mirror select buttons WARNING! (Continued) and a four-way mirror control switch. To adjust a mirror, could cause you to collide with another vehicle or other push the mirror select button for the mirror that you want object.
Page 77: Heated Mirrors - If Equipped
GETTING TO KNOW YOUR VEHICLE 75 Power mirror preselected positions can be controlled by NOTE: The Tilt Side Mirrors In Reverse feature is not the optional Memory Seat Feature. Refer to “Driver turned on when delivered from the factory. The Tilt Side Memory Seat”...
Page 78: Exterior Lights
76 GETTING TO KNOW YOUR VEHICLE Sun Visor “Slide-On-Rod” Feature — If Equipped The sun visor “Slide-On-Rod” feature allows for additional flexibility in positioning the sun visor to block out the sun. 1. Fold down the sun visor. 2. Unclip the visor from the center clip. 3.
Page 79: Daytime Running Lights - If Equipped
GETTING TO KNOW YOUR VEHICLE 77 NOTE: NOTE: If allowed by law in the country in which the vehicle was purchased the Daytime Running Lights can be • Your vehicle is equipped with plastic headlight and fog turned on and off using the Uconnect System, refer to light (if equipped) lenses that are lighter and less sus- “Uconnect Settings”...
Page 80: High/Low Beam Switch
78 GETTING TO KNOW YOUR VEHICLE High/Low Beam Switch If the windshield or Automatic High Beam Headlamp Control mirror is replaced, the mirror must be re-aimed to Push the multifunction lever toward the instrument panel ensure proper performance. See your local authorized to switch the headlights to high beams.
Page 81: Parking Lights And Panel Lights
GETTING TO KNOW YOUR VEHICLE 79 Headlight Delay NOTE: The engine must be running before the headlights will come on in the automatic mode. To aid in your exit, your vehicle is equipped with a headlight delay that will leave the headlights on for Parking Lights And Panel Lights approximately 90 seconds.
Page 82: Turn Signals
80 GETTING TO KNOW YOUR VEHICLE Turn Signals Move the multifunction lever up or down and the arrows on each side of the instrument cluster will flash to show proper operation of the front and rear turn signal lights. NOTE: If either light remains on and does not flash, or there is a very fast flash rate, check for a defective outside light bulb.
Page 83: Battery Saver
GETTING TO KNOW YOUR VEHICLE 81 Battery Saver INTERIOR LIGHTS To protect the life of your vehicle’s battery, load shedding Courtesy Lights is provided for both the interior and exterior lights. The courtesy lights can be turned on by pushing the top If the ignition is OFF and any door is left ajar for 10 minutes corner of the lens.
Page 84 82 GETTING TO KNOW YOUR VEHICLE Front Map/Reading Lights — If Equipped To turn the lights off, push the switch a second time. The lights also turn on when a door is opened. The lights will Lights are mounted in the overhead console. Each light can also turn on when the unlock button on the key fob is be turned on by pushing the switch on either side of the pushed.
Page 85 GETTING TO KNOW YOUR VEHICLE 83 Ambient Light — If Equipped Dimmer Control The overhead console is equipped with an ambient light Courtesy and dome lights are turned on when the front feature. This light casts illumination for improved visibility doors are opened or when the dimmer control (rotating of the floor and center console area.
Page 86: Windshield Wipers And Washers
84 GETTING TO KNOW YOUR VEHICLE WINDSHIELD WIPERS AND WASHERS supplement the brightness of the odometer, trip odometer, radio and overhead console by rotating the control to its The windshield wiper/washer controls are located on the farthest position up until you hear a click. This feature is multifunction lever on the left side of the steering column.
Page 87: Windshield Wiper Operation
GETTING TO KNOW YOUR VEHICLE 85 Windshield Wiper Operation Intermittent Wiper System Rotate the end of the lever to one of the first four detent Use one of the four intermittent wiper settings when positions for intermittent settings, the fifth detent for low weather conditions make a single wiping cycle, with a wiper operation and the sixth detent for high wiper operation.
Page 88 86 GETTING TO KNOW YOUR VEHICLE Windshield Washer Operation WARNING! To use the washer, push on the end of the lever (toward the Sudden loss of visibility through the windshield could steering wheel) and hold while spray is desired. If the lever lead to a collision.
Page 89: Rain Sensing Wipers - If Equipped
GETTING TO KNOW YOUR VEHICLE 87 The sensitivity of the system can be adjusted with the multifunction lever. Wiper delay position one is the least sensitive, and wiper delay position four is the most sensi- tive. Setting three should be used for normal rain condi- tions.
Page 90: Rear Window Wiper/Washer
88 GETTING TO KNOW YOUR VEHICLE Rear Window Wiper/Washer The Rain Sensing system has protection features for the wiper blades and arms, and will not operate under the The rear wiper/washer controls are located on the multi- following conditions: function lever on the left side of the steering column. The •...
Page 91: Climate Controls
GETTING TO KNOW YOUR VEHICLE 89 Rotate the center portion of the lever upward to the NOTE: As a protective measure, the pump will stop if the first detent for intermittent operation and to the switch is held for more than 20 seconds. Once the switch is second detent for continuous rear wiper operation.
Page 92: Automatic Climate Control Overview
90 GETTING TO KNOW YOUR VEHICLE Automatic Climate Control Overview Uconnect 4 With 7–inch Display Temperature Controls...
Page 93 GETTING TO KNOW YOUR VEHICLE 91 Uconnect 4C/4C NAV With 8.4–inch Display Temperature Controls...
Page 94 92 GETTING TO KNOW YOUR VEHICLE Control Descriptions Icon Description MAX A/C Button Press and release to change the current setting, the indicator illuminates when MAX A/C is ON. Performing this function again will cause the MAX A/C operation to switch into manual mode and the MAX A/C indicator will turn off.
Page 95 GETTING TO KNOW YOUR VEHICLE 93 Icon Description Front Defrost Button Press and release to change the current airflow setting to Defrost mode. The indicator illumi- nates when this feature is ON. Air comes from the windshield and side window demist outlets. When the defrost button is selected, the blower level may increase.
Page 96 94 GETTING TO KNOW YOUR VEHICLE Icon Description SYNC Button Press the Sync button on the touchscreen to toggle the Sync feature On/Off. The Sync indicator is illuminated when this feature is enabled. Sync is used to synchronize the passenger tempera- ture setting with the driver temperature setting.
Page 97 GETTING TO KNOW YOUR VEHICLE 95 Icon Description Bi-Level Mode Bi-Level Mode Air comes from the instrument panel outlets and floor outlets. A slight amount of air is directed through the defrost and side window demister outlets. NOTE: BI-LEVEL mode is designed under comfort conditions to provide cooler air out of the panel out- lets and warmer air from the floor outlets.
Page 98 96 GETTING TO KNOW YOUR VEHICLE Controlling The Rear Climate Controls From The CAUTION! Front ATC Panel Failure to follow these cautions can cause damage to the heating elements: • Use care when washing the inside of the rear win- dow.
Page 99 GETTING TO KNOW YOUR VEHICLE 97 The Three-Zone ATC system allows for adjustment of the rear climate controls from the front ATC panel. To change the rear system settings: • Press the REAR CLIMATE button on the touchscreen to change control to rear control mode, Rear display (below) will appear.
Page 100 98 GETTING TO KNOW YOUR VEHICLE Icon Description Rear Mode Controls Select the desired air distribution mode from the selectable modes on the touchscreen. The rear airflow distribution mode can be adjusted so air comes from the headliner outlets, and floor outlets. Headliner Headliner Mode Mode...
Page 101 GETTING TO KNOW YOUR VEHICLE 99 Icon Description Rear Temperature Display This display shows the temperature setting for the rear seat occupants. Blower Control Display This display shows the current Blower speed selection. Rear Auto Indicator This indicates when the system is in Rear Auto mode. Rear Lock Button Press and release to lock out the rear manual temperature controls from adjusting the rear tempera- ture and blower settings.
Page 102 100 GETTING TO KNOW YOUR VEHICLE Rear Automatic Temperature Control The rear ATC system has floor air outlets at the rear right side of the 3rd Row seats and overhead outlets at each outboard rear seating position. The system provides heated air through the floor outlets or cool, dehumidified air through the headliner outlets.
Page 103 GETTING TO KNOW YOUR VEHICLE 101 Icon Description Panel Mode Headliner Mode Air comes from the outlets in the headliner. Each of these outlets can be individually adjusted to direct the flow of air. Moving the air vanes of the outlets to one side will shut off the airflow. Bi-Level Mode Bi-Level Mode Air comes from both the headliner outlets and the floor outlets.
Page 104 102 GETTING TO KNOW YOUR VEHICLE Icon Description Rear Blower Control The rear blower control can be manually set to off, or any fixed blower speed by rotating the Blower Control Knob in the rear of the vehicle. This allows the rear seat occupants to control the volume of air circulated in the rear of the vehicle.
Page 105: Climate Control Functions
GETTING TO KNOW YOUR VEHICLE 103 NOTE: It is not necessary to move the temperature. The • If your air conditioning performance seems lower than system automatically adjusts the temperature, mode and expected, check the front of the A/C condenser (located fan speed to provide comfort as quickly as possible.
Page 106: Automatic Temperature Control (Atc) - If Equipped
104 GETTING TO KNOW YOUR VEHICLE Recirculation 2. Adjust the temperature you would like the system to maintain, by adjusting the driver, passenger, and rear When outside air contains smoke, odors, or high humidity, temperatures. Once the desired temperature is dis- or if rapid cooling is desired, you may wish to recirculate played, the system will achieve and automatically main- interior air by pressing the recirculation control button.
Page 107: Operating Tips
GETTING TO KNOW YOUR VEHICLE 105 Manual Operation Override CAUTION! (Continued) This system offers a full complement of manual override heater outlets are located in the right side trim panel, features. The AUTO symbol in the front ATC display will just behind the sliding door.
Page 108 106 GETTING TO KNOW YOUR VEHICLE Summer Operation Window Fogging The engine cooling system must be protected with a Interior fogging on the windshield can be quickly removed high-quality antifreeze coolant to provide proper corrosion by turning the mode selector to Defrost. The Defrost/Floor protection and to protect against engine overheating.
Page 109 GETTING TO KNOW YOUR VEHICLE 107 Outside Air Intake The climate control system filters outside air containing dust, pollen and some odors. Strong odors cannot be totally Make sure the air intake, located directly in front of the filtered out. Refer to “Dealer Service” in “Servicing And windshield, is free of obstructions, such as leaves.
Page 110 108 GETTING TO KNOW YOUR VEHICLE Control Setting Suggestions For Various Weather Conditions...
Page 111: Windows
GETTING TO KNOW YOUR VEHICLE 109 WINDOWS The power window switches remain active for up to 10 minutes after the ignition has been turned OFF. Opening a Power Windows vehicle front door will cancel this feature. The power window controls are located on the driver’s door trim panel.
Page 112 110 GETTING TO KNOW YOUR VEHICLE Auto-Down Auto-Up Feature With Anti-Pinch Protection — Driver And Front Passenger Door Only Both the driver and front passenger window switches have an Auto-Down feature. Push the window switch past the Lift the window switch fully upward to the second detent, first detent, release, and the window will go down auto- release, and the window will go up automatically.
Page 113: Wind Buffeting
GETTING TO KNOW YOUR VEHICLE 111 Reset Auto-Up Should the Auto-Up feature stop working, the window may need to be reset. To reset Auto-Up: 1. Make sure the door is fully closed. 2. Pull the window switch up to close the window com- pletely and continue to hold the switch up for an additional two seconds after the window is closed.
Page 114: Power Sunroof - If Equipped
112 GETTING TO KNOW YOUR VEHICLE POWER SUNROOF — IF EQUIPPED WARNING! (Continued) The power sunroof switch is located between the sun equipped with Keyless Enter-N-Go in the ACC or visors on the overhead console. ON/RUN mode. Occupants, particularly unattended children, can become entrapped by the power sun- roof while operating the power sunroof switch.
Page 115: Closing Sunroof
GETTING TO KNOW YOUR VEHICLE 113 Wind Buffeting Manual Mode To open the sunroof, push and hold the switch rearward. Wind buffeting can be described as the perception of The sunroof will move rearward and automatically stop at pressure on the ears or a helicopter-type sound in the ears. full open position.
Page 116: Venting Sunroof - Express
114 GETTING TO KNOW YOUR VEHICLE Relearn Procedure NOTE: If three consecutive sunroof close attempts result in Pinch Protect reversals, Pinch Protect will disable and the For vehicles equipped with a sunroof, there is a relearn sunroof must be closed in Manual Mode. procedure that allows you to calibrate the sunroof when the “Express Operation”...
Page 117: Hood
GETTING TO KNOW YOUR VEHICLE 115 HOOD 2. Reach under the hood from outside the vehicle, move the safety latch to the left and lift the hood. Opening The Hood To open the hood, two latches must be released. 1. Pull the release lever located below the instrument panel and in front of the driver’s door.
Page 118: Closing The Hood
116 GETTING TO KNOW YOUR VEHICLE Closing The Hood LIFTGATE Power Liftgate — If Equipped WARNING! Be sure the hood is fully latched before driving your The power liftgate may be opened by pushing vehicle. If the hood is not fully latched, it could open the electronic liftgate release (refer to “Keyless when the vehicle is in motion and block your vision.
Page 119 GETTING TO KNOW YOUR VEHICLE 117 NOTE: • If anything obstructs the power liftgate while it is closing or opening, the liftgate will automatically re- • In the event of a power malfunction to the liftgate, an verse to the closed or open position, provided it meets emergency liftgate latch release can be used to open the sufficient resistance.
Page 120: Cargo Area Features
118 GETTING TO KNOW YOUR VEHICLE WARNING! • Driving with the liftgate open can allow poisonous exhaust gases into your vehicle. You and your pas- sengers could be injured by these fumes. Keep the liftgate closed when you are operating the vehicle. •...
Page 121 GETTING TO KNOW YOUR VEHICLE 119 3. The liftgate may be opened with the cargo cover in place. WARNING! In a collision, a loose cargo cover in the vehicle could cause injury. It could fly around in a sudden stop and strike someone in the vehicle.
Page 122: Garage Door Opener - If Equipped
120 GETTING TO KNOW YOUR VEHICLE GARAGE DOOR OPENER — IF EQUIPPED WARNING! (Continued) HomeLink replaces up to three remote controls (handheld • To help protect against personal injury, passengers transmitters) that operate devices such as garage door should not be seated in the rear cargo area. The rear openers, motorized gates, lighting or home security sys- cargo space is intended for load carrying purposes tems.
Page 123: Before You Begin Programming Homelink
GETTING TO KNOW YOUR VEHICLE 121 To erase the channels, place the ignition in the ON/RUN position and push and hold the two outside HomeLink buttons (I and III) for up 20 seconds or until the red indicator flashes. NOTE: •...
Page 124 122 GETTING TO KNOW YOUR VEHICLE 2. Place the hand-held transmitter 1 to 3 inches (3 to 8 cm) away from the HomeLink button you wish to program while keeping the HomeLink indicator light in view. 3. Push and hold the HomeLink button you want to program while you push and hold the hand-held trans- mitter button.
Page 125: Programming A Non-Rolling Code
GETTING TO KNOW YOUR VEHICLE 123 NOTE: You have 30 seconds in which to initiate the next 2. Place the hand-held transmitter 1 to 3 inches (3 to 8 cm) step after the LEARN button has been pushed. away from the HomeLink button you wish to program while keeping the HomeLink indicator light in view.
Page 126: Canadian/Gate Operator Programming
124 GETTING TO KNOW YOUR VEHICLE Canadian/Gate Operator Programming 3. Continue to push and hold the HomeLink button while you push and release (“cycle”) your hand-held trans- For programming transmitters in Canada/United States mitter every two seconds until HomeLink has success- that require the transmitter signals to “time-out”...
Page 127: Using Homelink
GETTING TO KNOW YOUR VEHICLE 125 Using HomeLink Troubleshooting Tips To operate, switch the ignition to the ON/RUN position If you are having trouble programming HomeLink, here and the press and release the programmed HomeLink are some of the most common solutions: button.
Page 128: General Information
126 GETTING TO KNOW YOUR VEHICLE INTERNAL EQUIPMENT WARNING! (Continued) Storage are in the path of the door or gate. Only use this transceiver with a garage door opener that has a “stop Glove Compartment and reverse” feature as required by Federal safety The glove compartment is located on the passenger side of standards.
Page 129 GETTING TO KNOW YOUR VEHICLE 127 Door Storage To open the upper storage compartment, pull upward on the small latch located on the lid. Large storage areas are built into the door panels for easy access. Storage Compartment Latches Lift upward on the larger of the latches to access the lower Door Panel Storage storage compartment.
Page 130 128 GETTING TO KNOW YOUR VEHICLE Rear Full Center Console — If Equipped The rear full center console contains both an upper and a lower storage area. Upper Storage Compartment Lift upward on the larger of the latches to access the lower storage compartment.
Page 131 GETTING TO KNOW YOUR VEHICLE 129 CAUTION! Remove any items stored in the console cupholders or devices with cords routing through upper storage area. Damage may occur to upper console lid and device cables when upper storage compartment is lifted for- ward.
Page 132 130 GETTING TO KNOW YOUR VEHICLE When lifted forward there is access to the lower storage NOTE: When the lower storage compartment is accessed, compartment. it allows the armrest to flip forward for “fold flat mode”. Fold flat mode allows the console armrest to be lowered below the fold flat seat plane and protect the armrest vinyl from damage when using the vehicle to haul cargo.
Page 133 GETTING TO KNOW YOUR VEHICLE 131 Open storage areas, or cubby bins with removable liners, Rear Mini Center Console — If Equipped are located rearward of the cupholders and in the lower An open storage area, or cubby bin with removable liner, is front of the console.
Page 134: Cupholders
132 GETTING TO KNOW YOUR VEHICLE Cupholders Rear Cupholders Rear Center Arm Rest Cupholders — If Equipped Front Seat Cupholders There are two cupholders for the front seat passengers There are two cupholders for the rear seat passengers located in the center console. located in the fold-down center armrest.
Page 135 GETTING TO KNOW YOUR VEHICLE 133 Rear Full Console Cupholders — If Equipped The rear full console cupholders are equipped with a light ring that illuminates the cupholders for the rear passen- There are two cupholders for the rear seat passengers gers.
Page 136: Electrical Power Outlets
134 GETTING TO KNOW YOUR VEHICLE Rear Mini Console Cupholders — If Equipped Power outlets labeled with a “key” are powered when the ignition switch is in the ON or ACC position, while the There are two cupholders for the rear seat passengers outlets labeled with a “battery”...
Page 137 GETTING TO KNOW YOUR VEHICLE 135 The front power outlet is located inside the storage area on In addition to the front power outlet, there is also a power the center stack of the instrument panel. outlet located in the storage area of the center console. Front Power Outlet Front Center Console Outlet...
Page 138 136 GETTING TO KNOW YOUR VEHICLE If your vehicle is equipped with a rear full center console, The rear cargo power outlet is located in the right rear there is also a power outlet located in the lower storage cargo area. area of the rear full center console.
Page 139 GETTING TO KNOW YOUR VEHICLE 137 NOTE: The rear cargo power outlet can be changed to “battery” powered all the time by switching the power outlet right rear quarter panel fuse in the fuse panel from fuse location F90 to F91. Power Outlet Fuse Locations 1 —...
Page 140: Power Inverter - If Equipped
138 GETTING TO KNOW YOUR VEHICLE Power Inverter — If Equipped WARNING! (Continued) There is a 115 or 230 Volt, 150 Watt inverter outlet located • Close the lid when not in use and while driving the on the back of the center console to convert DC current to vehicle.
Page 141: Sunglasses Bin Door
GETTING TO KNOW YOUR VEHICLE 139 The power inverter is designed with built-in overload protection. If the power rating of 150 Watts is exceeded, the power inverter will automatically shut down. Once the electrical device has been removed from the outlet the inverter should automatically reset.
Page 142 140 GETTING TO KNOW YOUR VEHICLE Deploying The Crossbars 1. Starting with one crossbar, completely loosen the thumb screws at both ends of the crossbar. Roof Rack 1 — Side Rail 2 — Crossbar Thumb Screw The roof rack does not increase the total load carrying NOTE: The thumb screws cannot be fully removed.
Page 143 GETTING TO KNOW YOUR VEHICLE 141 2. Remove the crossbar from the stowed position by slid- 3. Starting with one crossbar, bend down the pivot sup- ing the crossbar towards the center of the roof. Repeat ports at each end. with crossbar on the opposite side.
Page 144 142 GETTING TO KNOW YOUR VEHICLE 4. Position the crossbars across the roof making sure the 5. Slide the cross bar into to the deploy position by moving letters on the crossbars align with the matching letters it towards the matching letter in the side rail. Be sure the on the side rail.
Page 145 GETTING TO KNOW YOUR VEHICLE 143 6. Deploy and tighten the second crossbar to complete the CAUTION! deployment of the crossbars. Use care when removing and handling the crossbars to prevent damage to the vehicle. 2. Starting with the one crossbar, bend up the pivot supports at each end.
Page 146 144 GETTING TO KNOW YOUR VEHICLE 3. Position the crossbar along the correct side rail. Make 4. Slide the crossbar outward, away from the center of the sure the letters on the crossbar align with the matching roof. The crossbar will nest fully within the side rail. letters on the side rail.
Page 147 GETTING TO KNOW YOUR VEHICLE 145 5. Once the driver’s side crossbar is in place, tighten the thumb screws completely. Stowed Crossbars NOTE: Tightening Crossbar • To help control wind noise, stow the crossbars in the side 6. Repeat the procedure to stow the second crossbar on the rails when they are not in use.
Page 148 146 GETTING TO KNOW YOUR VEHICLE WARNING! CAUTION! (Continued) • Load should always be secured to cross bars first, Cargo must be securely tied down before driving your with tie down loops used as additional securing vehicle. Improperly secured loads can fly off the ve- points if needed.
Page 149: Getting To Know Your Instrument Panel
GETTING TO KNOW YOUR INSTRUMENT PANEL CONTENTS INSTRUMENT CLUSTER ....148 WARNING LIGHTS AND MESSAGES ..161 ▫...
Page 150: Instrument Cluster
148 GETTING TO KNOW YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER Instrument Cluster Instrument Cluster Descriptions 2. Speedometer • Indicates vehicle speed. 1. Tachometer • Indicates the engine speed in revolutions per minute (RPM x 1000).
Page 151 GETTING TO KNOW YOUR INSTRUMENT PANEL 149 3. Temperature Gauge CAUTION! • The temperature gauge shows engine coolant tem- Driving with a hot engine cooling system could dam- perature. Any reading within the normal range indi- age your vehicle. If the temperature gauge reads “H” cates that the engine cooling system is operating pull over and stop the vehicle.
Page 152: Instrument Cluster Display
150 GETTING TO KNOW YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DISPLAY Location And Controls Your vehicle may be equipped with an instrument cluster display, which offers useful information to the driver. With the ignition in the STOP/OFF mode, opening/closing of a door will activate the display for viewing, and display the total miles, or kilometers, in the odometer.
Page 153 GETTING TO KNOW YOUR INSTRUMENT PANEL 151 • Audio • Down Arrow Button • Stored Messages Push and release the down arrow button to scroll downward through the main menu. • Screen Setup The system allows the driver to select information by •...
Page 154 152 GETTING TO KNOW YOUR INSTRUMENT PANEL The instrument cluster display is located in the center messages that consist of approximately 60 possible warn- portion of the cluster and consist of multiple sections: ing or information messages. These pop up messages fall into several categories: •...
Page 155: Engine Oil Life Reset
GETTING TO KNOW YOUR INSTRUMENT PANEL 153 • Unstored Messages Until RUN Unless reset, this message will continue to display each time you place the ignition in the ON/RUN position. To These messages deal primarily with the Remote Start turn off the message temporarily, push and release the OK feature.
Page 156: Display And Messages
154 GETTING TO KNOW YOUR INSTRUMENT PANEL Display And Messages 5. Push and release the up or down arrow button to exit the submenu screen. Includes the following, but not limited to: NOTE: If the indicator message illuminates when you •...
Page 157 GETTING TO KNOW YOUR INSTRUMENT PANEL 155 • Service Tire Pressure System • Remote Start Canceled Time Expired • Park Brake Engaged • Remote Start Disabled Start To Reset • Brake Fluid Low • Service Air Bag System • Engine Temperature Hot •...
Page 158: Safety
156 GETTING TO KNOW YOUR INSTRUMENT PANEL Instrument Cluster Display Selectable Menu Items • If one or more tires have low pressure, “Inflate Tire To XX” is displayed with the vehicle icon and the tire Push and release the up or down arrow button until the pressure values in each corner of the icon with the desired Selectable Menu item is displayed in the instru- pressure value of the low tire are displayed in a different...
Page 159 GETTING TO KNOW YOUR INSTRUMENT PANEL 157 Trip Battery Voltage • Displays the current voltage level of the battery. Push and release the up or down arrow button until the Trip icon/title is highlighted in the instrument cluster Driver Assist — If Equipped display, then push and release the left or right arrow Push and release the up or down arrow button until the button to select Trip A or Trip B.
Page 160: Screen Setup Driver Selectable Items
158 GETTING TO KNOW YOUR INSTRUMENT PANEL Stored Messages Gear Display • Full (default setting) Push and release the up or down arrow button until the Messages Menu item is highlighted. This feature shows the • Single number of stored warning messages. Pushing the right Favorite Menus arrow button will allow you to see what the stored messages are.
Page 161: Battery Saver On/Battery Saver Mode Message - Electrical Load Reduction Actions - If Equipped
GETTING TO KNOW YOUR INSTRUMENT PANEL 159 Upper Left • Trip A • None • Trip B • Compass (default setting) Defaults (Restores All Settings To Default Settings) • Outside Temp • Restore • Time • Cancel • Range To Empty (RTE) Battery Saver On/Battery Saver Mode Message —...
Page 162 160 GETTING TO KNOW YOUR INSTRUMENT PANEL • Audio and Telematics System When load reduction is activated, the message “Battery Saver On” or “Battery Saver Mode” will appear in the Loss of the battery charge may indicate one or more of the instrument cluster.
Page 163: Warning Lights And Messages
GETTING TO KNOW YOUR INSTRUMENT PANEL 161 • The battery was discharged by an electrical load left on • Evaluate the latest driving cycles (distance, driving time when the vehicle was parked. and parking time). • The battery was used for an extended period with the •...
Page 164 162 GETTING TO KNOW YOUR INSTRUMENT PANEL — Air Bag Warning Light been corrected. If the problem is related to the brake booster, the ABS pump will run when applying the brake, This light indicates a fault with the air bag, and will turn on and a brake pedal pulsation may be felt during each stop.
Page 165 GETTING TO KNOW YOUR INSTRUMENT PANEL 163 Vehicles equipped with the Anti-Lock Brake System (ABS) — Door Open Warning Light — If Equipped are also equipped with Electronic Brake Force Distribution This indicator will illuminate when a door is ajar/open and (EBD).
Page 166 164 GETTING TO KNOW YOUR INSTRUMENT PANEL The light should turn off. If the light remains on with the If the light turns on while driving, safely pull over and stop vehicle running, your vehicle will usually be drivable; the vehicle. If the A/C system is on, turn it off. Also, shift however, see an authorized dealer for service as soon as the transmission into NEUTRAL and idle the vehicle.
Page 167: Yellow Warning Lights
GETTING TO KNOW YOUR INSTRUMENT PANEL 165 Do not operate the vehicle until the cause is corrected. This CAUTION! light does not indicate how much oil is in the engine. The engine oil level must be checked under the hood. Continuous driving with the Transmission Tempera- ture Warning Light illuminated will eventually cause —...
Page 168 166 GETTING TO KNOW YOUR INSTRUMENT PANEL several typical driving styles. In most situations, the ve- — Electronic Stability Control (ESC) Active hicle will drive normally and will not require towing. Warning Light — If Equipped This light will indicate when the Electronic Stability Con- When the engine is running, the MIL may flash to alert trol system is Active.
Page 169 GETTING TO KNOW YOUR INSTRUMENT PANEL 167 — Electronic Stability Control (ESC) Off Warning CAUTION! Light — If Equipped Do not continue driving with one or more flat tires as This light indicates the Electronic Stability Control (ESC) is handling may be compromised. Stop the vehicle, off.
Page 170 168 GETTING TO KNOW YOUR INSTRUMENT PANEL can lead to tire failure. Under-inflation also reduces fuel replacing one or more tires or wheels on your vehicle to efficiency and tire tread life, and may affect the vehicle’s ensure that the replacement or alternate tires and wheels handling and stopping ability.
Page 171 GETTING TO KNOW YOUR INSTRUMENT PANEL 169 — Anti-Lock Brake (ABS) Warning Light — Service Adaptive Cruise Control Warning Light — If Equipped This light monitors the Anti-Lock Brake System (ABS). The light will turn on when the ignition is placed in the This light will turn on when a ACC is not operating and ON/RUN or ACC/ON/RUN position and may stay on for needs service.
Page 172: Yellow Indicator Lights
170 GETTING TO KNOW YOUR INSTRUMENT PANEL Green Indicator Lights — LaneSense Fault Warning Light — If Equipped This light will turn on when the LaneSense system is not — Adaptive Cruise Control (ACC) Set With operating and needs service. Please see your authorized Target Light —...
Page 173: White Indicator Lights
GETTING TO KNOW YOUR INSTRUMENT PANEL 171 — LaneSense Indicator Light — If Equipped NOTE: • A continuous chime will sound if the vehicle is driven The LaneSense indicator is solid green when both lane mark- more than 1 mile (1.6 km) with either turn signal on. ings have been detected and the system is “armed”...
Page 174: Blue Indicator Lights
172 GETTING TO KNOW YOUR INSTRUMENT PANEL detected lane line. Refer to “LaneSense — If Equipped in If any of these systems require service, the OBD II system “Starting And Operating” for further information. will turn on the Malfunction Indicator Light (MIL). It will also store diagnostic codes and other information to assist Blue Indicator Lights your service technician in making repairs.
Page 175: Onboard Diagnostic System (Obd Ii) Cybersecurity
GETTING TO KNOW YOUR INSTRUMENT PANEL 173 Onboard Diagnostic System (OBD II) Cybersecurity EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS Your vehicle is required to have an Onboard Diagnostic system (OBD II) and a connection port to allow access to In some localities, it may be a legal requirement to pass an information related to the performance of your emissions inspection of your vehicle’s emissions control system.
Page 176 174 GETTING TO KNOW YOUR INSTRUMENT PANEL 2. As soon as you cycle the ignition switch to the ON If your OBD II system is not ready, you should see your position, you will see the “Malfunction Indicator Light authorized dealer or repair facility. If your vehicle was (MIL)”...
Page 177 SAFETY CONTENTS SAFETY FEATURES ..... .176 ▫ Seat Belt Systems ..... .204 ▫...
Page 178: Safety Features
176 SAFETY SAFETY FEATURES These are all normal characteristics of ABS. Anti-Lock Brake System (ABS) WARNING! The Anti-Lock Brake System (ABS) provides increased • The ABS contains sophisticated electronic equip- vehicle stability and brake performance under most brak- ment that may be susceptible to interference caused ing conditions.
Page 179: Electronic Brake Control System
SAFETY Electronic Brake Control System WARNING! (Continued) Your vehicle is equipped with an advanced Electronic • The capabilities of an ABS equipped vehicle must never Brake Control system (EBC). This system includes Elec- be exploited in a reckless or dangerous manner that tronic Brake Force Distribution (EBD), Anti-Lock Brake could jeopardize the user’s safety or the safety of others.
Page 180 178 SAFETY If the “Brake System Warning Light” remains on or comes WARNING! on while driving, it indicates that the brake system is not functioning properly and that immediate service is re- The Brake Assist System (BAS) cannot prevent the quired.
Page 181 SAFETY The following conditions must be met in order for HSA to WARNING! (Continued) activate: while pulling a trailer. HSA is not a substitute for • The feature must be enabled. active driving involvement. It is always the driver’s • The vehicle must be stopped. responsibility to be attentive to distance to other ve- hicles, people, and objects, and most importantly brake •...
Page 182 180 SAFETY For vehicles not equipped with an instrument cluster Towing With HSA display, perform the following steps: HSA will also provide assistance to mitigate roll back while towing a trailer. 1. Center the steering wheel (front wheels pointing straight forward). WARNING! 2.
Page 183 SAFETY Traction Control System (TCS) the intended path, ESC applies the brake of the appropriate wheel to assist in counteracting the oversteer or understeer This system monitors the amount of wheel spin of each of condition. the driven wheels. If wheel spin is detected, the TCS may •...
Page 184 182 SAFETY ESC Operating Modes WARNING! (Continued) NOTE: Depending upon model and mode of operation, the road conditions. ESC cannot prevent accidents, in- ESC system may have multiple operating modes. cluding those resulting from excessive speed in turns, driving on very slippery surfaces, or hydro- ESC On planing.
Page 185 SAFETY NOTE: For vehicles with multiple partial ESC modes a “ESC Activation/Malfunction Indicator Light” comes on momentary button push will toggle the ESC mode. Mul- continuously with the engine running, a malfunction has tiple momentary button pushed may be required to return been detected in the ESC system.
Page 186 184 SAFETY • The ESC system will make buzzing or clicking sounds WARNING! when it is active. This is normal; the sounds will stop when ESC becomes inactive following the maneuver Many factors, such as vehicle loading, road conditions that caused the ESC activation. and driving conditions, influence the chance that wheel lift or rollover may occur.
Page 187 SAFETY to individual wheels to attempt to stop the trailer from Dynamic Steering Torque (DST) swaying. TSC is disabled when the ESC system is in the Dynamic Steering Torque is a feature of the ESC and “Partial Off” modes. Electric Power Steering (EPS) modules that provides torque at the steering wheel for certain driving conditions WARNING! in which the ESC module is detecting vehicle instability.
Page 188: Auxiliary Driving Systems
186 SAFETY AUXILIARY DRIVING SYSTEMS The BSM detection zone covers approximately one lane on both sides of the vehicle 12 ft (3.8 m). The zone length starts Blind Spot Monitoring (BSM) — If Equipped at the outside rear view mirror and extends approximately The Blind Spot Monitoring (BSM) system uses two radar 10 ft (3 m) beyond the rear bumper of the vehicle.
Page 189 SAFETY • The Blind Spot Monitoring (BSM) system may experi- The BSM system notifies the driver of objects in the ence drop outs (blinking on and off) of the side mirror detection zones by illuminating the BSM warning light Warning Indicator lamps when a motorcycle or any located in the outside mirrors.
Page 190 188 SAFETY Entering From The Side Entering From The Rear Vehicles that move into your adjacent lanes from either Vehicles that come up from behind your vehicle on either side of the vehicle. side and enter the rear detection zone with a relative speed of less than 30 mph (48 km/h).
Page 191 SAFETY Overtaking Traffic If you pass another vehicle slowly (with a relative speed of less than 15 mph (24 km/h)) and the vehicle remains in the blind spot for approximately 1.5 seconds, the warning light will be illuminated. If the difference in speed between the two vehicles is greater than 15 mph (24 km/h), the warning light will not illuminate.
Page 192 190 SAFETY Stationary Objects Opposing Traffic The BSM system will not alert you of objects that are WARNING! traveling in the opposite direction of the vehicle in adjacent lanes. The Blind Spot Monitoring system is only an aid to help detect objects in the blind spot zones. The BSM system is not designed to detect pedestrians, bicyclists, or animals.
Page 193 SAFETY Rear Cross Path (RCP) (5 km/h), to objects moving a maximum of approximately 20 mph (32 km/h), such as in parking lot situations. The Rear Cross Path (RCP) feature is intended to aid the driver when backing out of parking spaces where their NOTE: In a parking lot situation, oncoming vehicles can be vision of oncoming vehicles may be blocked.
Page 194 192 SAFETY Modes Of Operation object are present on the same side at the same time, both the visual and audible alerts will be issued. In addition to Three selectable modes of operation are available in the the audible alert the radio (if on) will also be muted. Uconnect System.
Page 195: Forward Collision Warning (Fcw) With Mitigation
SAFETY General Information NOTE: FCW monitors the information from the forward looking sensors as well as the Electronic Brake Controller The following regulatory statement applies to all Radio (EBC), to calculate the probability of a forward collision. Frequency (RF) devices equipped in this vehicle: When the system determines that a forward collision is This device complies with Part 15 of the FCC Rules and probable, the driver will be provided with audible and...
Page 196 194 SAFETY • It is unsafe to test the FCW system. To prevent such misuse of the system, after four Active Braking events within an ignition cycle, the Active Braking portion of FCW will be deactivated until the next ignition cycle. •...
Page 197 SAFETY FCW Braking Status And Sensitivity NOTE: • Changing the FCW status to “Only Warning” prevents The FCW Sensitivity and Active Braking status are pro- the system from providing limited active braking, or grammable through the Uconnect System. Refer to additional brake support if the driver is not braking “Uconnect Settings”...
Page 198: Tire Pressure Monitor System (Tpms)
196 SAFETY FCW Limited Warning The tire pressure will vary with temperature by about 1 psi (7 kPa) for every 12°F (6.5°C). This means that when the If the instrument cluster displays “ACC/FCW Limited outside temperature decreases, the tire pressure will de- Functionality”...
Page 199 SAFETY NOTE: When filling warm tires, the tire pressure may need CAUTION! to be increased up to an additional 4 psi (30 kPa) above the recommended cold placard pressure in order to turn the • The TPMS has been optimized for the original Tire Pressure Monitoring Telltale Light off.
Page 200 198 SAFETY NOTE: • The TPMS is not intended to replace normal tire care and maintenance, or to provide warning of a tire failure or condition. • The TPMS should not be used as a tire pressure gauge while adjusting your tire pressure. •...
Page 201 SAFETY Tire Pressure Monitoring Low Pressure Warnings The Tire Pressure Monitoring Telltale Light will illuminate in the instrument cluster, and an audible chime will be activated, when one or more of the four active road tire pressures are low. In addition, the instru- ment cluster will display an Inflate to XX message and a graphic display of the pressure value(s) with the low tire(s) in a different color.
Page 202 200 SAFETY The system will automatically update, the graphic display will not be present, and a pressure value will be displayed of the pressure value(s) will return to its original color and instead of dashes. A system fault can occur by any of the the Tire Pressure Monitoring Telltale Light will extinguish following: once the updated tire pressure(s) have been received.
Page 203 SAFETY a pressure value in the different color graphic display and TPMS Deactivation — If Equipped an “Inflate to XX” message will be displayed. After driving The TPMS can be deactivated if replacing all four wheel the vehicle for up to 20 minutes above 15 mph (24 km/h), and tire assemblies (road tires) with wheel and tire assem- the Tire Pressure Monitoring Telltale Light will flash on blies that do not have TPMS Sensors, such as when...
Page 204: Occupant Restraint Systems
202 SAFETY OCCUPANT RESTRAINT SYSTEMS The instrument cluster will display the “SERVICE TPM SYSTEM” message and then display pressure values in Some of the most important safety features in your vehicle place of the dashes. On the next ignition cycle the SER- are the restraint systems: VICE TPM SYSTEM message will no longer be displayed Occupant Restraint Systems Features...
Page 205 SAFETY 2. If a child from 2 to 12 years old (not in a rear-facing child 7. The driver and front passenger seats should be moved restraint) must ride in the front passenger seat, move the back as far as practical to allow the front air bags room seat as far back as possible and use the proper child to inflate.
Page 206: Seat Belt Systems
204 SAFETY Seat Belt Systems equipped with outboard front passenger seat BeltAlert) is unbuckled when the ignition switch is first in the START or Buckle up even though you are an excellent driver, even on ON/RUN position the Seat Belt Reminder Light will turn on short trips.
Page 207 SAFETY Change of Status Lap/Shoulder Belts All seating positions in your vehicle are equipped with If the driver or outboard front seat passenger (if equipped lap/shoulder belts. with outboard front passenger seat BeltAlert) unbuckles their seat belt while the vehicle is traveling, the BeltAlert The seat belt webbing retractor will lock only during very warning sequence will begin until the seat belts are buck- sudden stops or collisions.
Page 208 206 SAFETY WARNING! (Continued) WARNING! • It is dangerous to ride in a cargo area, inside or • A lap belt worn too high can increase the risk of outside of a vehicle. In a collision, people riding in injury in a collision. The seat belt forces won’t be at these areas are more likely to be seriously injured or the strong hip and pelvic bones, but across your killed.
Page 209 SAFETY Lap/Shoulder Belt Operating Instructions WARNING! (Continued) 1. Enter the vehicle and close the door. Sit back and adjust • A seat belt that is worn under your arm is dangerous. the seat. Your body could strike the inside surfaces of the vehicle in a collision, increasing head and neck 2.
Page 210 208 SAFETY 3. When the seat belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” Positioning The Lap Belt 5. Position the shoulder belt across the shoulder and chest with minimal, if any slack so that it is comfortable and Inserting Latch Plate Into Buckle not resting on your neck.
Page 211 SAFETY Lap/Shoulder Belt Untwisting Procedure Use the following procedure to untwist a twisted lap/ shoulder belt. 1. Position the latch plate as close as possible to the anchor point. 2. At about 6 to 12 inches (15 to 30 cm) above the latch plate, grasp and twist the seat belt webbing 180 degrees to create a fold that begins immediately above the latch plate.
Page 212 210 SAFETY NOTE: The adjustable upper shoulder belt anchorage is Seat Belt Extender equipped with an Easy Up feature. This feature allows the If a seat belt is not long enough to fit properly, even when shoulder belt anchorage to be adjusted in the upward the webbing is fully extended and the adjustable upper position without pushing or squeezing the release button.
Page 213 SAFETY Seat Belts And Pregnant Women Seat Belt Pretensioner The front seat belt system is equipped with pretensioning devices that are designed to remove slack from the seat belt in the event of a collision. These devices may improve the performance of the seat belt by removing slack from the seat belt early in a collision.
Page 214 212 SAFETY Switchable Automatic Locking Retractor (ALR) The seat belts in the passenger seating positions are equipped with a Switchable Automatic Locking Retractor (ALR) which is used to secure a child restraint system. For additional information, refer to “Installing Child Restraints Using The Vehicle Seat Belt”...
Page 215 SAFETY In Automatic Locking Mode, the shoulder belt is automati- cally pre-locked. The seat belt will still retract to remove any slack in the shoulder belt. Use the Automatic Locking Mode anytime a child restraint is installed in a seating position that has a seat belt with this feature.
Page 216 214 SAFETY 3. Allow the seat belt to retract. As the seat belt retracts, Supplemental Active Head Restraints (AHR) you will hear a clicking sound. This indicates the seat These head restraints are passive, deployable components, belt is now in the Automatic Locking Mode. and vehicles with this equipment cannot be readily iden- tified by any markings, only through visual inspection of How To Disengage The Automatic Locking Mode...
Page 217 SAFETY NOTE: The Active Head Restraints (AHR) may or may not WARNING! deploy in the event of a front or side impact. However, if during a front impact, a secondary rear impact occurs, the • All occupants, including the driver, should not oper- AHR may deploy based on the severity and type of the ate a vehicle or sit in a vehicle’s seat until the head impact.
Page 218: Supplemental Restraint Systems (Srs)
216 SAFETY Resetting Active Head Restraints (AHR) WARNING! Deployed AHRs are not able to best protect you in all types of collisions. Have deployed AHRs reset by an authorized dealer immediately. Supplemental Restraint Systems (SRS) Some of the safety features described in this section may be standard equipment on some models, or may be optional equipment on others.
Page 219 SAFETY • Knee Impact Bolsters The ORC turns on the Air Bag Warning Light in the instru- ment panel for approximately four to eight seconds for a • Driver and Front Passenger Air Bags self-check when the ignition switch is first in the ON/RUN •...
Page 220: Glove Compartment
218 SAFETY NOTE: If the speedometer, tachometer, or any engine panel. The Redundant Air Bag Warning Light will stay on related gauges are not working, the Occupant Restraint until the fault is cleared. In addition, a single chime will Controller (ORC) may also be disabled. In this condition sound to alert you that the Redundant Air Bag Warning the air bags may not be ready to inflate for your protection.
Page 221 SAFETY WARNING! (Continued) • Never place a rear-facing child restraint in front of an air bag. A deploying passenger front air bag can cause death or serious injury to a child 12 years or younger, including a child in a rear-facing child restraint.
Page 222 220 SAFETY This vehicle may be equipped with a driver and/or front WARNING! (Continued) passenger seat belt buckle switch that detects whether the • Relying on the air bags alone could lead to more driver or front passenger seat belt is buckled. The seat belt severe injuries in a collision.
Page 223 SAFETY Because air bag sensors measure vehicle deceleration over Knee Impact Bolsters time, vehicle speed and damage by themselves are not The Knee Impact Bolsters help protect the knees of the good indicators of whether or not an air bag should have driver and front passenger, and position the front occu- deployed.
Page 224 222 SAFETY Supplemental Side Air Bags Supplemental Seat-Mounted Side Air Bags (SABs) This vehicle is equipped with Supplemental Seat-Mounted Side Air Bags (SABs). Supplemental Seat-Mounted Side Air Bags (SABs) are located in the outboard side of the front seats. The SABs are marked with a “SRS AIRBAG”...
Page 225 SAFETY WARNING! Do not use accessory seat covers or place objects between you and the Side Air Bags; the performance could be adversely affected and/or objects could be pushed into you, causing serious injury. Supplemental Side Air Bag Inflatable Curtains (SABICs) This vehicle is equipped with Supplemental Side Air Bag Inflatable Curtains (SABICs).
Page 226 224 SAFETY The SABICs inflate with enough force to injure occupants if Side Impacts they are not belted and seated properly, or if items are The Side Air Bags are designed to activate in certain side positioned in the area where the SABICs inflate. Children impacts.
Page 227 SAFETY Side Air Bags are a supplement to the seat belt restraint WARNING! system. Side Air Bags deploy in less time than it takes to blink your eyes. • Side Air Bags need room to inflate. Do not lean against the door or window. Sit upright in the center WARNING! of the seat.
Page 228 226 SAFETY • Supplemental Side Air Bags The Side Air Bags will not deploy in all rollover events. The rollover sensing system determines if a rollover event may • Supplemental Knee Air Bags be in progress and whether deployment is appropriate. In •...
Page 229 SAFETY • As the air bags deflate, you may see some smoke-like NOTE: particles. The particles are a normal by-product of the • Air bag covers may not be obvious in the interior trim, process that generates the non-toxic gas used for air bag but they will open during air bag deployment.
Page 230 228 SAFETY Enhanced Accident Response System Reset WARNING! (Continued) Procedure • It is dangerous to try to repair any part of the air bag In order to reset the Enhanced Accident Response System system yourself. Be sure to tell anyone who works on functions after an event, the ignition switch must be your vehicle that it has an air bag system.
Page 231: Child Restraints
SAFETY Event Data Recorder (EDR) data (e.g., name, gender, age, and crash location) are recorded. However, other parties, such as law enforcement, This vehicle is equipped with an event data recorder could combine the EDR data with the type of personally (EDR).
Page 232 230 SAFETY Before buying any restraint system, make sure that it has a WARNING! label certifying that it meets all applicable Safety Stan- dards. You should also make sure that you can install it in In a collision, an unrestrained child can become a the vehicle where you will use it.
Page 233 SAFETY Summary Of Recommendations For Restraining Children In Vehicles Recommended Type Of Child Child Size, Height, Weight Or Age Restraint Infants and Toddlers Children who are two years old or Either an Infant Carrier or a Convert- younger and who have not reached ible Child Restraint, facing rearward the height or weight limits of their in the rear seat of the vehicle...
Page 234 232 SAFETY Infant And Child Restraints WARNING! Safety experts recommend that children ride rear-facing in • Never place a rear-facing child restraint in front of an the vehicle until they are two years old or until they reach air bag. A deploying passenger front air bag can either the height or weight limit of their rear-facing child cause death or serious injury to a child 12 years or restraint.
Page 235 SAFETY All children whose weight or height is above the forward- WARNING! (Continued) facing limit for the child seat should use a belt-positioning the vehicle. In a sudden stop or accident, it could booster seat until the vehicle’s seat belts fit properly. If the strike the occupants or seatbacks and cause serious child cannot sit with knees bent over the vehicle’s seat cushion personal injury.
Page 236 234 SAFETY If the answer to any of these questions was “no,” then the WARNING! child still needs to use a booster seat in this vehicle. If the child is using the lap/shoulder belt, check seat belt fit Never allow a child to put the shoulder belt under an periodically and make sure the seat belt buckle is latched.
Page 237 SAFETY Lower Anchors And Tethers For CHildren (LATCH) used with the top tether anchorage to install the child Restraint System restraint. Please see the following table for more information. LATCH Positions For Installing Child Restraints In This Vehicle LATCH Label Your vehicle is equipped with the child restraint anchorage system called LATCH, which stands for Lower Anchors and Tethers for CHildren.
Page 238 236 SAFETY 60/40 Second Row LATCH Positions (7 Passenger) Captain’s Chairs Second Row LATCH Positions (6 Passenger) Lower Anchorage Symbol (2 Anchorages Per Seating Position) Top Tether Anchorage Symbol Lower Anchorage Symbol (2 Anchorages Per Seating Position) Top Tether Anchorage Symbol Frequently Asked Questions About Installing Child Restraints With LATCH What is the weight limit (child’s weight + 65 lbs (29.5 kg)
Page 239 SAFETY Frequently Asked Questions About Installing Child Restraints With LATCH Can the LATCH anchorages and the seat belt Do not use the seat belt when you use the be used together to attach a rear-facing or LATCH anchorage system to attach a rear- forward-facing child restraint? facing or forward-facing child restraint.
Page 240 238 SAFETY Frequently Asked Questions About Installing Child Restraints With LATCH Can the head restraints be removed? Yes — 5 Passenger 5 Passenger: Only the head restraint in the No — 6 Passenger center position may be removed. Yes — 7 Passenger 7 Passenger: The head restraint in the center position may be removed in the second row, as well as the outboard head restraints in the...
Page 241 SAFETY Six Passenger Rear Seat Lower Anchorages Seven Passenger Rear Seat Lower Anchorages...
Page 242 240 SAFETY Locating The Upper Tether Anchorages 2nd Row Upper Tether Anchorage Locations There are tether strap anchorages behind each rear seating position located on the back of the seat. (Six/Seven Passenger) There are tether strap anchorages behind each rear seating position located on the back of the seat.
Page 243 SAFETY Five Passenger Top Tether Strap Mounting Seven Passenger Top Tether Strap Mounting (2nd Row Bench)
Page 244 242 SAFETY 5 Passenger Models And 3rd Row Upper Tether Anchor- age Locations For 6 And 7 Passenger Models There are tether strap anchorages behind each rear seating position located on the back of the seat. To access them, pull the carpeted floor panel away from the seat back, this will expose the top tether strap anchorages.
Page 245 SAFETY Center Seat LATCH — Five Or Seven Passenger Seating Only WARNING! • Do not install a child restraint in the center position using the LATCH system. This position is not ap- proved for installing child seats using the LATCH attachments.
Page 246 244 SAFETY 1. Loosen the adjusters on the lower straps and on the tether strap of the child seat so that you can more easily attach the hooks or connectors to the vehicle anchor- ages. 2. Place the child seat between the lower anchorages for that seating position.
Page 247 SAFETY 6. Test that the child restraint is installed tightly by pulling WARNING! back and forth on the child seat at the belt path. It should not move more than 1 inch (25.4 mm) in any • Improper installation of a child restraint to the direction.
Page 248 246 SAFETY Installing Child Restraints Using The Vehicle Seat Belt Please see the table below and the following sections for more information. Child restraint systems are designed to be secured in vehicle seats by lap belts or the lap belt portion of a Lap/Shoulder Belt Systems For Installing Child lap/shoulder belt.
Page 249 SAFETY 60/40 Second Row (7 Passenger) Automatic Locking Captain’s Chairs Second Row (6 Passenger) Automatic Retractor (ALR) Locations Locking Retractor (ALR) Locations ALR = Switchable Automatic Locking Retractor ALR = Switchable Automatic Locking Retractor Top Tether Anchorage Symbol Top Tether Anchorage Symbol Frequently Asked Questions About Installing Child Restraints With Seat Belts What is the weight limit (child’s weight + Weight limit of the...
Page 250 248 SAFETY Frequently Asked Questions About Installing Child Restraints With Seat Belts Can the rear-facing child restraint touch the Contact between the front passenger seat and back of the front passenger seat? the child restraint is allowed, if the child re- straint manufacturer also allows contact.
Page 251 SAFETY 1. Place the child seat in the center of the seating position. 6. Try to pull the webbing out of the retractor. If it is For some second row seats, you may need to recline the locked, you should not be able to pull out any webbing. seat and/or raise the head restraint to get a better fit.
Page 252 250 SAFETY Installing Child Restraints Using The Top Tether 1. Look behind the seating position where you plan to Anchorage install the child restraint to find the tether anchorage. You may need to move the seat forward to provide WARNING! better access to the tether anchorage.
Page 253 SAFETY Pulling Down The Carpet Floor Panel To Access Top Top Tether Strap Anchorage (Located On Seatback) Tether Strap Anchorage (Six Passenger) 3. Route the tether strap to provide the most direct path for the strap between the anchor and the child seat. If your vehicle is equipped with adjustable rear head restraints, raise the head restraint, and where possible, route the tether strap under the head restraint and between the...
Page 254 252 SAFETY 5. Attach the tether strap hook of the child restraint to the top tether anchorage as shown in the diagram. Bench Seat Top Tether Strap Mounting (7 Passenger Seating) Bench Seat Top Tether Strap Mounting (5 Passenger Seating)
Page 255: Transporting Pets
SAFETY WARNING! (Continued) • An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchorage position directly be- hind the child seat to secure a child restraint top tether strap. •...
Page 256: Safety Tips
254 SAFETY SAFETY TIPS Exhaust Gas Transporting Passengers WARNING! NEVER TRANSPORT PASSENGERS IN THE CARGO Exhaust gases can injure or kill. They contain carbon AREA. monoxide (CO), which is colorless and odorless. Breathing it can make you unconscious and can even- WARNING! tually poison you.
Page 257: Safety Checks You Should Make Inside The Vehicle
SAFETY Whenever a change is noticed in the sound of the exhaust Air Bag Warning Light system, when exhaust fumes can be detected inside the The Air Bag warning light will turn on for four to vehicle, or when the underside or rear of the vehicle is eight seconds as a bulb check when the ignition switch damaged, have a competent mechanic inspect the complete is first turned to ON/RUN.
Page 258 256 SAFETY Floor Mat Safety Information WARNING! (Continued) Always use floor mats designed to fit your vehicle. Only use a • ONLY install floor mats designed to fit your vehicle. floor mat that does not interfere with the operation of the NEVER install a floor mat that cannot be properly accelerator, brake or clutch pedals.
Page 259: Periodic Safety Checks You Should Make Outside The Vehicle
SAFETY Periodic Safety Checks You Should Make Outside WARNING! (Continued) The Vehicle • NEVER place any objects under the floor mat (e.g., Tires towels, keys, etc.). These objects could change the position of the floor mat and may cause interference Examine tires for excessive tread wear and uneven wear with the accelerator, brake, or clutch pedals.
Page 261 STARTING AND OPERATING CONTENTS STARTING THE ENGINE ....263 ▫ Fuel Economy (ECO) Mode....273 ▫...
Page 262 260 STARTING AND OPERATING ▫ To Start The Engine While In Autostop Mode . .289 ▫ To Cancel ......299 ▫...
Page 263 STARTING AND OPERATING 261 ▫ Enabling And Disabling ParkSense ..322 ▫ Changing LaneSense Status ....339 ▫ Service The ParkSense Rear Park Assist System. .322 PARKVIEW REAR BACK UP CAMERA .
Page 264 262 STARTING AND OPERATING ▫ Trailer Towing Weights (Maximum Trailer Weight ▫ Towing This Vehicle Behind Another Vehicle . . .358 Ratings) ......350 ▫...
Page 265: Starting The Engine
STARTING AND OPERATING 263 STARTING THE ENGINE WARNING! (Continued) Before starting your vehicle, adjust your seat, adjust the inside • Do not leave children or animals inside parked and outside mirrors, fasten your seat belt, and if present, vehicles in hot weather. Interior heat build-up may instruct all other occupants to buckle their seat belts.
Page 266: Keyless Enter-N-Go - Ignition
264 STARTING AND OPERATING Keyless Enter-N-Go — Ignition 2. Press and hold the brake pedal while pushing the ENGINE START/STOP button once. 3. The system takes over and attempts to start the vehicle. If the vehicle fails to start, the starter will disengage automatically after 10 seconds.
Page 267 STARTING AND OPERATING 265 4. If the gear selector is not in PARK and the ENGINE 3. Push the ENGINE START/STOP button a second time START/STOP button is pushed once with the vehicle to place the ignition to the RUN mode. speed above 5 MPH (8 km/h), the instrument cluster 4.
Page 268 266 STARTING AND OPERATING AutoPark will engage when all of these conditions are met: WARNING! (Continued) • Vehicle is equipped with an 8-speed transmission • AutoPark is a supplemental feature. It is not de- signed to replace the need to shift your vehicle into •...
Page 269: If Engine Fails To Start
STARTING AND OPERATING 267 ALWAYS DO A VISUAL CHECK that your vehicle is in WARNING! PARK by looking for the P in the instrument cluster display and on the shifter. As an added precaution, always If vehicle speed is above 1.2 MPH (1.9 km/h), the apply the parking brake when exiting the vehicle.
Page 270: Cold Weather Operation (Below -22°F Or −30°C)
268 STARTING AND OPERATING Cold Weather Operation (Below –22°F Or −30°C) WARNING! To ensure reliable starting at these temperatures, use of an Remember to disconnect the engine block heater cord externally powered electric engine block heater (available before driving. Damage to the 110-115 Volt electrical from your authorized dealer) is recommended.
Page 271: Parking Brake
STARTING AND OPERATING 269 CAUTION! Never use Non-Detergent Oil or Straight Mineral Oil in the engine or damage may result. NOTE: A new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be considered a normal part of the break-in and not interpreted as a problem.
Page 272 270 STARTING AND OPERATING When parking on a hill, it is important to turn the front WARNING! (Continued) wheels toward the curb on a downhill grade and away • When leaving the vehicle, always make sure the from the curb on an uphill grade. Apply the parking brake keyless ignition node is in the OFF mode, remove the before placing the gear selector in PARK, otherwise the key fob from the vehicle and lock the vehicle.
Page 273: Automatic Transmission
STARTING AND OPERATING 271 CAUTION! WARNING! (Continued) indicates PARK (P) without blinking. Ensure that the If the Brake Warning Light remains on with the park- vehicle is completely stopped, and the PARK posi- ing brake released, a brake system malfunction is tion is properly indicated, before exiting the vehicle.
Page 274: Ignition Park Interlock
272 STARTING AND OPERATING WARNING! (Continued) CAUTION! (Continued) • When exiting the vehicle, always make sure the • Do not shift between PARK, REVERSE, NEUTRAL, ignition is in the OFF mode, remove the key fob from or DRIVE when the engine is above idle speed. •...
Page 275: Brake/Transmission Shift Interlock System
STARTING AND OPERATING 273 Brake/Transmission Shift Interlock System This vehicle is equipped with a Brake Transmission Shift Interlock system (BTSI) that holds the transmission gear selector in PARK unless the brakes are applied. To shift the transmission out of PARK, the engine must be running and the brake pedal must be pressed.
Page 276: Eight-Speed Automatic Transmission
274 STARTING AND OPERATING Eight-Speed Automatic Transmission and road conditions. The transmission electronics are self- calibrating; therefore, the first few shifts on a new vehicle may The transmission gear range (PRNDM) is displayed both be somewhat abrupt. This is a normal condition, and precision on the gear selector and in the instrument cluster.
Page 277 STARTING AND OPERATING 275 Gear Ranges Do not depress the accelerator pedal when shifting from PARK or NEUTRAL into another gear range. NOTE: After selecting any gear range, wait a moment to allow the selected gear to engage before accelerating. This is especially important when the engine is cold.
Page 278 276 STARTING AND OPERATING NOTE: On vehicles equipped with the electronically WARNING! (Continued) shifted transfer case, ensure that the transfer case is in • The transmission may not engage PARK if the ve- AWD AUTO or LOW RANGE position on the AWD hicle is moving.
Page 279 STARTING AND OPERATING 277 WARNING! (Continued) CAUTION! transmission is locked in PARK, securing the vehicle • Before moving the transmission gear selector out of against unwanted movement. PARK, you must start the engine, and also press the • When exiting the vehicle, always make sure the brake pedal.
Page 280 278 STARTING AND OPERATING NOTE: If the gear selector cannot be moved to the PARK, CAUTION! REVERSE, or NEUTRAL position (when pushed forward) it is probably in the MANUAL (AutoStick, +/-) position Towing the vehicle, coasting, or driving for any other (beside the DRIVE position).
Page 281 STARTING AND OPERATING 279 During cold temperatures, transmission operation may be may stall. In some situations, the transmission may not modified depending on engine and transmission tempera- re-engage if the engine is turned off and restarted. The ture as well as vehicle speed. This feature improves warm Malfunction Indicator Light (MIL) may be illuminated.
Page 282 280 STARTING AND OPERATING 6. Shift into the desired gear range. If the problem is no Operation longer detected, the transmission will return to normal To activate AutoStick mode, move the gear selector into the operation. MANUAL (M) position (beside the DRIVE position), or tap NOTE: Even if the transmission can be reset, we recom- one of the shift paddles on the steering wheel (if equipped).
Page 283 STARTING AND OPERATING 281 In AutoStick mode, the transmission will shift up or down • Holding the (-) paddle depressed (if equipped), or when (+/-) is manually selected by the driver, unless an holding the gear selector in the (-) position, will down- engine lugging or overspeed condition would result.
Page 284: Sport Mode - If Equipped
282 STARTING AND OPERATING SPORT MODE — IF EQUIPPED Electronically Shifted Transfer Case (Three-Position Switch) — If Equipped Your vehicle is equipped with a Sport Mode feature. This mode is a configuration set up for typical enthusiast This is an electronic shift transfer case and it is operated by driving.
Page 285 STARTING AND OPERATING 283 This electronically shifted transfer case is designed to be selection. Refer to “Instrument Cluster Display” in “Get- driven in the AWD AUTO position for normal street and ting To Know Your Instrument Panel” for further informa- highway conditions on dry hard surfaced roads.
Page 286 284 STARTING AND OPERATING NOTE: Before retrying a selection, make certain that all the When operating your vehicle in LOW RANGE, the engine necessary requirements for selecting a new transfer case speed is approximately three times that of the AWD AUTO position have been met.
Page 287: Shifting Procedure
STARTING AND OPERATING 285 Shifting Procedure LOW Range All-Wheel Drive Low Range – This range provides low NOTE: speed all-wheel drive. Locks the front and rear driveshafts • If any of the requirements to select a new transfer case together forcing the front and rear wheels to rotate at the position have not been met, the transfer case will not same speed.
Page 288 286 STARTING AND OPERATING Shifting can be performed with the vehicle rolling 2 to NOTE: 3 mph (3 to 5 km/h) or completely stopped. Use either of • If steps 1 or 2 of either the Preferred or Alternate the following procedures: Procedure are not satisfied prior to attempting the shift or if they no longer are being met while the shift attempt Preferred Procedure...
Page 289: Fuel Saver Technology - If Equipped
STARTING AND OPERATING 287 FUEL SAVER TECHNOLOGY — IF EQUIPPED Alternate electric power steering efforts can be selected through the Uconnect System. Refer to ”Customer Pro- This feature offers improved fuel economy by shutting off grammable Features” within “Uconnect Settings” in “Mul- four of the engine’s eight cylinders during light load and timedia”...
Page 290: Stop/Start System - If Equipped
288 STARTING AND OPERATING If the Steering icon is displayed and the “POWER STEER- To Activate The Autostop Mode, The Following Must ING SYSTEM OVER TEMP” message is displayed on the Occur: instrument cluster screen, they indicate that extreme steer- •...
Page 291: Possible Reasons The Engine Does Not Autostop
STARTING AND OPERATING 289 Possible Reasons The Engine Does Not Autostop Other Factors Which Can Inhibit Autostop Include: • Accelerator pedal input. Prior to engine shut down, the system will check many safety and comfort conditions to see if they are fulfilled. •...
Page 292: To Manually Turn Off The Stop/Start System
290 STARTING AND OPERATING • HVAC system temperature or fan speed is manually 1. Push the STOP/START OFF switch (located on the adjusted. switch bank). The light on the switch will illuminate. • Battery voltage drops too low. 2. The “STOP/START OFF” message will appear in instru- ment cluster display within the Stop/Start section.
Page 293: System Malfunction
STARTING AND OPERATING 291 System Malfunction If there is a malfunction in the STOP/START system, the system will not shut down the engine. A “SERVICE STOP/ START SYSTEM” message will appear in the instrument cluster display. Refer to “Instrument Cluster Display“ in “Getting to Know Your Instrument Panel”...
Page 294: To Activate
292 STARTING AND OPERATING To Set A Desired Speed WARNING! Turn the Speed Control on. When the vehicle has reached Speed Control can be dangerous where the system the desired speed, push the SET (+) or SET (-) button and cannot maintain a constant speed.
Page 295: To Accelerate For Passing
STARTING AND OPERATING 293 • If the button is continually pushed, the set speed will • If the button is continually pushed, the set speed will continue to increase until the button is released, then the continue to decrease until the button is released, then the new set speed will be established.
Page 296: To Resume Speed
294 STARTING AND OPERATING ADAPTIVE CRUISE CONTROL (ACC) — IF WARNING! EQUIPPED Speed Control can be dangerous where the system Adaptive Cruise Control (ACC) increases the driving con- cannot maintain a constant speed. Your vehicle could venience provided by cruise control while traveling on go too fast for the conditions, and you could lose highways and major roadways.
Page 297 STARTING AND OPERATING 295 The Cruise Control system has two control modes: WARNING! (Continued) • Adaptive Cruise Control mode for maintaining an ap- operation of the vehicle under all road conditions. propriate distance between vehicles. Your complete attention is always required while •...
Page 298: Adaptive Cruise Control (Acc) Operation
296 STARTING AND OPERATING WARNING! (Continued) release the brakes and that the brakes must be applied manually. An audible chime will sound when the brakes are released. You should switch off the ACC system: • When driving in fog, heavy rain, heavy snow, sleet, heavy traffic, and complex driving situations (i.e., in highway construction zones).
Page 299: Activating Adaptive Cruise Control (Acc)
STARTING AND OPERATING 297 Activating Adaptive Cruise Control (ACC) To Activate/Deactivate You can only engage ACC if the vehicle speed is above Push and release the Adaptive Cruise Control (ACC) 0 mph (0 km/h). on/off button. The ACC menu in the instrument cluster displays “ACC Ready.”...
Page 300: To Set A Desired Acc Speed
298 STARTING AND OPERATING To Set A Desired ACC Speed When the vehicle reaches the speed desired, push the SET (+) button or the SET (-) button and release. The instrument cluster display will display the set speed. If the system is set when the vehicle speed is below 20 mph (32 km/h), the set speed shall be defaulted to 20 mph (32 km/h).
Page 301: To Cancel
STARTING AND OPERATING 299 To Cancel • The Normal (Fixed Speed) Cruise Control on/off button is pushed. The following conditions cancel the system: • The ignition is turned OFF. • The brake pedal is applied. To Resume • The CANC button is pushed. If there is a set speed in memory push the RES (resume) •...
Page 302: To Vary The Speed Setting
300 STARTING AND OPERATING To Vary The Speed Setting • If the button is continually pushed, the set speed will continue to increase in 10 km/h increments until the To Increase Speed button is released. The increase in set speed is reflected While ACC is set, you can increase the set speed by in the instrument cluster display.
Page 303 STARTING AND OPERATING 301 • The ACC system applies the brake down to a full stop Metric Speed (km/h) when following a target vehicle. If an ACC host vehicle • Pushing the SET (-) button once will result in a 1 km/h follows a target vehicle to a standstill, the host vehicle decrease in set speed.
Page 304: Setting The Following Distance In Acc
302 STARTING AND OPERATING Setting The Following Distance In ACC The specified following distance for ACC can be set by varying the distance setting between four bars (longest), three bars (long), two bars (medium) and one bar (short). Using this distance setting and the vehicle speed, ACC calculates and sets the distance to the vehicle ahead.
Page 305 STARTING AND OPERATING 303 Distance Setting 2 Bars (Medium) Distance Setting 1 Bar (Short) To increase the distance setting, push the Distance Setting — Increase button and release. Each time the button is pushed, the distance setting increases by one bar (longer). To decrease the distance setting, push the Distance Setting —...
Page 306: Overtake Aid
304 STARTING AND OPERATING Indicator” icon, and the system adjusts vehicle speed automatically to maintain the distance setting, regardless of the set speed. The vehicle will then maintain the set distance until: • The vehicle ahead accelerates to a speed above the set speed.
Page 307: Acc Operation At Stop
STARTING AND OPERATING 305 ACC Operation At Stop WARNING! (Continued) If the ACC system brings your vehicle to a standstill while in the path of the vehicle. Failure to follow these following a target vehicle, if the target vehicle starts warnings can result in a collision and death or serious moving within two seconds of your vehicle coming to a personal injury.
Page 308: Display Warnings And Maintenance
306 STARTING AND OPERATING Display Warnings And Maintenance Adaptive Cruise Control Set When the SET (+) or the SET (-) button (located on the “Wipe Front Radar Sensor In Front Of Vehicle” steering wheel) is pushed, the display will read “ACC Warning SET.”...
Page 309 STARTING AND OPERATING 307 NOTE: If the “ACC/FCW Unavailable Wipe Front Radar • Do not attach or install any accessories near the sensor, Sensor” warning is active Normal (Fixed Speed) Cruise including transparent material or aftermarket grilles. Control is still available. For additional information refer to Doing so could cause an ACC system failure or malfunc- “Normal (Fixed Speed) Cruise Control Mode”...
Page 310: Precautions While Driving With Acc
308 STARTING AND OPERATING “Clean Front Windshield” Warning NOTE: If the “ACC/FCW Limited Functionality Clean Front Windshield” message occurs frequently (e.g. more The “ACC/FCW Limited Functionality Clean Front Wind- than once on every trip) without any snow, rain, mud, or shield”...
Page 311 STARTING AND OPERATING 309 Offset Driving Turns And Bends ACC may not detect a vehicle in the same lane that is offset When driving on a curve with ACC engaged, the system from your direct line of travel, or a vehicle merging in from may decrease the vehicle speed and acceleration for stabil- a side lane.
Page 312 310 STARTING AND OPERATING Using ACC On Hills Lane Changing When driving on hills, ACC may not detect a vehicle in ACC may not detect a vehicle until it is completely in the your lane. Depending on the speed, vehicle load, traffic lane in which you are traveling.
Page 313 STARTING AND OPERATING 311 Narrow Vehicles Stationary Objects And Vehicles Some narrow vehicles traveling near the outer edges of the ACC does not react to stationary objects and stationary lane or edging into the lane are not detected until they have vehicles.
Page 314: General Information
312 STARTING AND OPERATING General Information To change between the different control modes, push the Adaptive Cruise Control (ACC) on/off button which turns The following regulatory statement applies to all Radio the ACC and the Normal (Fixed Speed) Cruise Control off. Frequency (RF) devices equipped in this vehicle: Pushing the Normal (Fixed Speed) Cruise Control on/off This device complies with Part 15 of the FCC Rules and...
Page 315 STARTING AND OPERATING 313 will operate at the selected speed. Once a speed has been Metric Speed (km/h) set a message “CRUISE CONTROL SET TO MPH (km/h)” • Pushing the SET (+) button once will result in a 1 km/h will appear indicating what speed was set.
Page 316 314 STARTING AND OPERATING • If the button is continually pushed, the set speed will • The vehicle parking brake is applied. continue to decrease in 5 mph decrements until the • The braking temperature exceeds normal range (over- button is released. The decrease in set speed is reflected heated).
Page 317: Parksense Rear Park Assist - If Equipped
STARTING AND OPERATING 315 PARKSENSE REAR PARK ASSIST — IF EQUIPPED • The automatic braking function may not be applied fast enough for obstacles that move toward the rear of the The ParkSense Rear Park Assist system provides visual and vehicle from the left and/or right sides.
Page 318: Parksense Sensors
316 STARTING AND OPERATING ParkSense Warning Display ParkSense will retain the last system state (enabled or disabled) from the last ignition cycle when the ignition is The ParkSense Warning screen will only be displayed if changed to the ON/RUN position. Sound and Display is selected from the Customer - Pro- grammable Features section of the Uconnect System.
Page 319: Parksense Display
STARTING AND OPERATING 317 ParkSense Display If an obstacle is detected in the left and/or right rear region, the display will show a single arc in the left and/or When the vehicle is in REVERSE and an obstacle has been right rear region and the system will produce a tone.
Page 320 318 STARTING AND OPERATING Slow Tone Slow Tone...
Page 321 STARTING AND OPERATING 319 Fast Tone Fast Tone...
Page 322 320 STARTING AND OPERATING The vehicle is close to the obstacle when the warning display shows one flashing arc and sounds a continuous tone. The following chart shows the warning alert opera- tion when the system is detecting an obstacle: Continuous Tone WARNING ALERTS Rear Dis-...
Page 323 STARTING AND OPERATING 321 WARNING ALERTS Rear Dis- Greater 79-59 inches 59-47 inches 47-39 inches 39-25 inches 25-12 inches Less than tance than (200- (150- (120- (100-65 cm) (65-30 cm) 12 inches (inches/cm) 79 inches 150 cm) 120 cm) 100 cm) (30 cm) (200 cm) Arcs-Left...
Page 324: Enabling And Disabling Parksense
322 STARTING AND OPERATING Enabling And Disabling ParkSense SENSORS” or the “PARKSENSE UNAVAILABLE SERVICE REQUIRED” message. Refer to “Instrument Cluster Display”. ParkSense can be enabled and disabled with the ParkSense When the gear selector is moved to REVERSE and the system switch.
Page 325: Parksense System Usage Precautions
STARTING AND OPERATING 323 ParkSense System Usage Precautions properly. The ParkSense system might not detect an obstacle behind the fascia/bumper, or it could provide a NOTE: false indication that an obstacle is behind the fascia/ • Ensure that the rear bumper is free of snow, ice, mud, bumper.
Page 326: Parksense Front And Rear Park Assist - If Equipped
324 STARTING AND OPERATING PARKSENSE FRONT AND REAR PARK ASSIST — WARNING! (Continued) IF EQUIPPED • Before using ParkSense, it is strongly recommended The ParkSense Park Assist system provides visual and that the ball mount and hitch ball assembly is audible indications of the distance between the rear and/or disconnected from the vehicle when the vehicle is front fascia and a detected obstacle when backing up or...
Page 327: Parksense Sensors
STARTING AND OPERATING 325 • The automatic braking function may not be applied fast ParkSense will retain the last system state (enabled or enough for obstacles that move toward the rear of the disabled) from the last ignition cycle when the ignition is vehicle from the left and/or right sides.
Page 328: Parksense Warning Display
326 STARTING AND OPERATING ParkSense Display The six ParkSense sensors, located in the front fascia/ bumper, monitor the area in front of the vehicle that is The warning display will turn on indicating the system within the sensors’ field of view. The sensors can detect status when the vehicle is in REVERSE or when the vehicle obstacles from approximately 12 inches (30 cm) up to is in DRIVE and an obstacle has been detected.
Page 329 STARTING AND OPERATING 327 If an object is detected in the left and/or right rear region, the display will show a single arc in the left and/or right rear region and the system will produce a tone. As the vehicle moves closer to the object, the display will show the single arc moving closer to the vehicle and the tone will change from a single 1/2 second tone to slow, to fast, to continuous.
Page 330 328 STARTING AND OPERATING Slow Tone For Rear Only Fast Tone For Rear Only...
Page 331 STARTING AND OPERATING 329 Fast Tone Continuous Tone...
Page 332 330 STARTING AND OPERATING The vehicle is close to the obstacle when the instrument cluster display shows one flashing arc and sounds a continuous tone. The following chart shows the warning alert operation when the system is detecting an obstacle: WARNING ALERTS FOR REAR Rear Dis- Greater...
Page 333 STARTING AND OPERATING 331 WARNING ALERTS FOR FRONT Front Distance Greater than 47-39 inches 39-25 inches 25-12 inches Less than (inches/cm) 47 inches (120-100 cm) (100-65 cm) (65-30 cm) 12 inches (120 cm) (30 cm) Audible Alert None None None Fast Continuous Chime...
Page 334: Enabling And Disabling Parksense
332 STARTING AND OPERATING Enabling And Disabling ParkSense Service The ParkSense Park Assist System ParkSense can be enabled and disabled with the ParkSense During vehicle start up, when the ParkSense System has switch. detected a faulted condition, the instrument cluster will actuate a single chime, once per ignition cycle, and it will When the ParkSense switch is pushed to disable display the PARKSENSE UNAVAILABLE WIPE REAR...
Page 335: Cleaning The Parksense System
STARTING AND OPERATING 333 Refer to “Instrument Cluster Display” in “Getting To Know • Jackhammers, large trucks, and other vibrations could Your Instrument Panel” for further information. affect the performance of ParkSense. If PARKSENSE UNAVAILABLE WIPE REAR SENSORS • When you turn ParkSense off, the instrument cluster or PARKSENSE UNAVAILABLE WIPE FRONT SEN- will display “PARKSENSE OFF.”...
Page 336 334 STARTING AND OPERATING fascia/bumper. Failure to do so can result in the system WARNING! (Continued) misinterpreting a close object as a sensor problem, hitch ball will be much closer to the obstacle than the causing the “PARKSENSE UNAVAILABLE SERVICE rear fascia when the loudspeaker sounds the con- REQUIRED”...
Page 337: Lanesense - If Equipped
STARTING AND OPERATING 335 LANESENSE — IF EQUIPPED The driver may manually override the haptic warning by applying torque into the steering wheel at any time. LaneSense Operation When only a single lane marking is detected and the driver The LaneSense system is operational at speeds above unintentionally drifts across the lane marking (no turn 37 mph (60 km/h) and below 112 mph (180 km/h).
Page 338: Turning Lanesense On Or Off
336 STARTING AND OPERATING Turning LaneSense On Or Off The default status of LaneSense is “off”. The LaneSense button is located on the switch panel below the Uconnect display. Lane Sense On Message To turn the LaneSense system off, push the LaneSense button once (LED turns on).
Page 339: Lanesense Warning Message
STARTING AND OPERATING 337 LaneSense Warning Message Left Lane Departure — Only Left Lane Detected • When the LaneSense system is on, the LaneSense telltale The LaneSense system will indicate the current lane drift is solid white when only the left lane marking has been condition through the instrument cluster display.
Page 340 338 STARTING AND OPERATING • When the LaneSense system senses a lane drift situation, NOTE: The LaneSense system operates with the similar behavior for a right lane departure when only the right the left thick lane line and left thin line turn solid yellow. lane marking has been detected.
Page 341: Changing Lanesense Status
STARTING AND OPERATING 339 Changing LaneSense Status • When the LaneSense system senses the lane has been approached and is in a lane departure situation, the left The LaneSense system has settings to adjust the intensity of thick lane line flashes yellow (on/off) and the left thin the torque warning and the warning zone sensitivity line remains solid yellow.
Page 342 340 STARTING AND OPERATING the top of the screen. After five seconds this note will NOTE: The ParkView Rear Back Up Camera has program- disappear. The ParkView camera is located on the rear of mable modes of operation that may be selected through the the vehicle above the rear license plate.
Page 343 STARTING AND OPERATING 341 NOTE: If snow, ice, mud, or any foreign substance builds WARNING! up on the camera lens, clean the lens, rinse with water, and dry with a soft cloth. Do not cover the lens. Drivers must be careful when backing up even when using the ParkView Rear Back Up Camera.
Page 344: Refueling The Vehicle
342 STARTING AND OPERATING REFUELING THE VEHICLE 1. Push the fuel filler door release switch (located under the headlamp switch). Fuel Filler Door NOTE: In certain cold conditions, ice may prevent the fuel door from opening. If this occurs, lightly push on the fuel door to break the ice buildup and re-release the fuel door Fuel Filler Door Release Switch using the inside release button.
Page 345 STARTING AND OPERATING 343 5. Fill the vehicle with fuel – when the fuel nozzle “clicks” WARNING! or shuts off the fuel tank is full. • Never have any smoking materials lit in or near the 6. Wait five seconds before removing the fuel nozzle to vehicle when the fuel door is open or the tank is allow fuel to drain from nozzle.
Page 346: Emergency Fuel Filler Door Release
344 STARTING AND OPERATING Emergency Fuel Filler Door Release If you are unable to open the fuel filler door, use the fuel filler door emergency release. 1. Open the liftgate. 2. Push the inboard edge of the left storage bin to the center, this will pop up the outboard edge.
Page 347: Vehicle Loading
STARTING AND OPERATING 345 VEHICLE LOADING Tire Size The tire size on the Vehicle Certification Label represents Gross Vehicle Weight Rating (GVWR) the actual tire size on your vehicle. Replacement tires must The GVWR is the total permissible weight of your vehicle be equal to the load capacity of this tire size.
Page 348: Trailer Towing
346 STARTING AND OPERATING TRAILER TOWING The entire vehicle should first be weighed on a commercial scale to insure that the GVWR has not been exceeded. The In this section you will find safety tips and information on weight on the front and rear of the vehicle should then be limits to the type of towing you can reasonably do with determined separately to be sure that the load is properly your vehicle.
Page 349 STARTING AND OPERATING 347 Gross Trailer Weight (GTW) Gross Axle Weight Rating (GAWR) The GTW is the weight of the trailer plus the weight of all The GAWR is the maximum capacity of the front and rear cargo, consumables and equipment (permanent or tempo- axles.
Page 350 348 STARTING AND OPERATING Trailer Sway Control vehicle’s front axle and the trailer axle(s). When used in accordance with the manufacturer’s directions, it provides The trailer sway control can be a mechanical telescoping for a more level ride, offering more consistent steering and link that can be installed between the hitch receiver and the brake control thereby enhancing towing safety.
Page 351: Trailer Hitch Classification
STARTING AND OPERATING 349 Trailer Hitch Classification and should be used to assist you in selecting the correct trailer hitch for your intended towing condition. The following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can tow Trailer Hitch Classification Definitions Class Max.
Page 352: Trailer Towing Weights
350 STARTING AND OPERATING Trailer Towing Weights (Maximum Trailer Weight Ratings) GCWR (Gross Max. GTW Max. Trailer Engine Model Combined Wt. Frontal Area (Gross Trailer Tongue Wt. Rating) Wt.) (See Note) 3.6L RWD Light Duty 8,900 lbs 40 sq ft 3,500 lbs 350 lbs (159 kg) Cooling...
Page 353: Trailer Hitch Receiver Cover Removal - If Equipped
STARTING AND OPERATING 351 NOTE: • The trailer tongue weight must be considered as part of the combined weight of occupants and cargo, and should never exceed the weight referenced on the Tire and Loading Information placard. Refer to “Tires” in “Servicing And Maintenance”...
Page 354: Trailer And Tongue Weight
352 STARTING AND OPERATING Hitch Receiver Cover Weight Distribution To reinstall the cover after towing repeat the procedure in Consider the following items when computing the weight reverse order. on the rear axle of the vehicle: • The tongue weight of the trailer. NOTE: Be sure to engage all tabs of the hitch receiver cover in the bumper fascia prior to installation.
Page 355: Towing Requirements
STARTING AND OPERATING 353 NOTE: Remember that everything put into or on the Maintenance” for the proper maintenance intervals. When trailer adds to the load on your vehicle. Also, additional towing a trailer, never exceed the GAWR or GCWR ratings. factory-installed options or dealer-installed options must WARNING! be considered as part of the total load on your vehicle.
Page 356 354 STARTING AND OPERATING Towing Requirements — Tires WARNING! (Continued) • Do not attempt to tow a trailer while using a compact • Vehicles with trailers should not be parked on a spare tire. grade. When parking, apply the parking brake on the tow vehicle.
Page 357 STARTING AND OPERATING 355 Towing Requirements — Trailer Brakes CAUTION! • Do not interconnect the hydraulic brake system or If the trailer weighs more than 1,000 lbs (453 kg) vacuum system of your vehicle with that of the trailer. loaded, it should have its own brakes and they should This could cause inadequate braking and possible per- be of adequate capacity.
Page 358: Towing Tips
356 STARTING AND OPERATING NOTE: • Disconnect trailer wiring connector from the vehicle before launching a boat (or any other device plugged into vehicle’s electrical connect) into water. • Be sure to reconnect after clear from water area. Seven-Pin Connector 1 —...
Page 359 STARTING AND OPERATING 357 Automatic Transmission Speed Control — If Equipped • Do not use on hilly terrain or with heavy loads. Select the DRIVE range when towing. The transmission controls include a drive strategy to avoid frequent shifting • When using the speed control, if you experience speed when towing.
Page 360: Snow Plow
358 STARTING AND OPERATING SNOW PLOW WARNING! Snow plows, winches, and other aftermarket equipment Do not add a snow plow, winches, or any other should not be added to the front end of your vehicle. The aftermarket equipment to the front of your vehicle. airbag crash sensors may be affected by the change in the This could adversely affect the functioning of the front end structure.
Page 361: Recreational Towing - Rear-Wheel Drive Models
STARTING AND OPERATING 359 NOTE: When towing your vehicle, always follow appli- CAUTION! cable state and provincial laws. Contact state and provin- cial Highway Safety offices for additional details. Towing with the rear wheels on the ground will cause severe transmission damage. Damage from improper Recreational Towing —...
Page 362: Recreational Towing - All-Wheel Drive Models (Two-Speed Transfer Case)
360 STARTING AND OPERATING Recreational Towing — All-Wheel Drive Models CAUTION! (Continued) (Two-Speed Transfer Case) • Towing this vehicle in violation of the above require- The transfer case must be shifted into NEUTRAL (N) and the ments can cause severe transmission and/or transfer transmission must be in PARK for recreational towing.
Page 363 STARTING AND OPERATING 361 CAUTION! It is necessary to follow these steps to be certain that the transfer case is fully in NEUTRAL (N) before recreational towing to prevent damage to internal parts. 1. Bring the vehicle to a complete stop on level ground, with the engine running.
Page 364 362 STARTING AND OPERATING 9. Firmly apply the parking brake. NOTE: • Steps 1 through 3 are requirements that must be met 10. With the transmission and transfer case in NEUTRAL, before pushing the NEUTRAL (N) button, and must push and hold the ENGINE START/STOP button until continue to be met until the shift has been completed.
Page 365 STARTING AND OPERATING 363 3. Start the engine. 8. After the NEUTRAL (N) button has been released, the transfer case will shift to the position indicated by the 4. Press and hold the brake pedal. selector switch. 5. Shift the transmission into NEUTRAL. 9.
Page 366: Driving Tips
364 STARTING AND OPERATING DRIVING TIPS NOTE: • Steps 1 through 5 are requirements that must be met On-Road Driving Tips before pushing the NEUTRAL (N) button, and must Utility vehicles have higher ground clearance and a nar- continue to be met until the shift has been completed. If rower track to make them capable of performing in a wide any of these requirements are not met before pushing variety of off-road applications.
Page 367: Off-Road Driving Tips
STARTING AND OPERATING 365 Off-Road Driving Tips CAUTION! When To Use 4WD LOW Range — If Equipped When driving through water, do not exceed 5 mph When off-road driving, shift to 4WD LOW for additional (8 km/h). Always check water depth before entering as traction.
Page 368: Hill Climbing
366 STARTING AND OPERATING Standing Water Hill Climbing Avoid driving in standing water deeper than 20 inches NOTE: Before attempting to climb a hill, determine the (51 cm), and reduce speed appropriately to minimize wave conditions at the crest and/or on the other side. effects.
Page 369 STARTING AND OPERATING 367 Remember, never drive diagonally across a hill; always After Driving Off-Road drive straight up or down. Off-road operation puts more stress on your vehicle than does most on-road driving. After going off-road, it is If the wheels start to slip as you approach the crest of a hill, always a good idea to check for damage.
Page 370 368 STARTING AND OPERATING WARNING! Abrasive material in any part of the brakes may cause excessive wear or unpredictable braking. You might not have full braking power when you need it to prevent a collision. If you have been operating your vehicle in dirty conditions, get your brakes checked and cleaned as necessary.
Page 371 IN CASE OF EMERGENCY CONTENTS HAZARD WARNING FLASHERS ... .370 ▫ Road Tire Installation ....398 ASSIST AND SOS MIRROR —...
Page 372: Hazard Warning Flashers
370 IN CASE OF EMERGENCY HAZARD WARNING FLASHERS ASSIST AND SOS MIRROR — IF EQUIPPED The Hazard Warning flasher switch is located on the switch bank just above the climate controls. Push the switch to turn on the Hazard Warning flasher.
Page 373 IN CASE OF EMERGENCY 371 ASSIST Call WARNING! The ASSIST Button is used to automatically connect you to ALWAYS obey traffic laws and pay attention to the any one of the following support centers: road. ALWAYS drive safely with your hands on the •...
Page 374 372 IN CASE OF EMERGENCY 2. The LED light located between the ASSIST and SOS NOTE: buttons on the Rearview Mirror will turn green once a • Your vehicle may be transmitting data as authorized connection to a SOS operator has been made. by the subscriber.
Page 375 IN CASE OF EMERGENCY 373 WARNING! WARNING! (Continued) ANY REASON (INCLUDING DURING OR AFTER • If anyone in the vehicle could be in danger (e.g., fire AN ACCIDENT), THE UCONNECT FEATURES, or smoke is visible, dangerous road conditions or APPS AND SERVICES, AMONG OTHERS, WILL location), do not wait for voice contact from an NOT OPERATE.
Page 376 374 IN CASE OF EMERGENCY • An In-Vehicle Audio message will state “Vehicle device • The SOS Call system software and/or hardware are requires service. Please contact your dealer.” damaged during a crash. • The vehicle battery loses power or becomes discon- WARNING! nected during a vehicle crash.
Page 377 IN CASE OF EMERGENCY 375 NOTE: General Information • Your vehicle may be transmitting data as authorized by This device complies with Part 15 of the FCC Rules. the subscriber. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) •...
Page 378: Bulb Replacement
376 IN CASE OF EMERGENCY BULB REPLACEMENT Replacement Bulbs Interior Bulbs Bulb Number Glove Compartment Lamp Grab Handle Lamp L002825W5W Overhead Console Reading Lamps VT4976 Visor Vanity Lamp V26377 Rear Cargo Lamp 214–2 Underpanel Courtesy Lamps Instrument Cluster (General Illumination) Telltale/Hazard Lamp Exterior Bulbs Bulb Number...
Page 379: Bulb Replacement
IN CASE OF EMERGENCY 377 Bulb Number Front Park/Turn Signal Lamps (Base) 3157NAK Front Turn Signal Lamps (Uplevel & Premium) 3157NAK Front Park Lamp/Daytime Running Lamp (Uplevel & LED (Serviced At Authorized Dealer) Premium) Front Side Marker Lamps LED (Serviced At Authorized Dealer) Front Fog Lamps Rear Tail Lamps/Sidemarker Lamps LED (Serviced At Authorized Dealer)
Page 380 378 IN CASE OF EMERGENCY 4. Firmly grasp the access cap and rotate counterclockwise WARNING! to remove lamp housing. A transient high voltage occurs at the bulb sockets of 5. Firmly grasp the low/high beam bulb and connector High Intensity Discharge (HID) headlamps when the assembly and rotate counterclockwise to remove from headlamp switch is turned ON.
Page 381 IN CASE OF EMERGENCY 379 Front Turn Signal CAUTION! 1. Open the hood. • Do not touch the new bulb with your fingers. Oil 2. Turn the turn signal bulb one–quarter turn counter- contamination will severely shorten bulb life. If the clockwise to remove from housing.
Page 382: Fuses
380 IN CASE OF EMERGENCY 5. Reinstall the socket(s). WARNING! (Continued) 6. Reverse process to reinstall the liftgate trim. • Before replacing a fuse, make sure that the ignition is off and that all the other services are switched off Center High-Mounted Stop Lamp (CHMSL) and/or disengaged.
Page 383: Underhood Fuses
IN CASE OF EMERGENCY 381 Underhood Fuses Also, please be aware that when using power outlets for extended periods of time with the engine off may result in The Power Distribution Center is located in the engine vehicle battery discharge. compartment near the battery.
Page 384 382 IN CASE OF EMERGENCY Cavity Cartridge Fuse Micro Fuse Description 60 Amp Yellow – Radiator Fan 40 Amp Green – Compressor for Air Suspension — If Equipped 40 Amp Green – Anti-lock Brakes/Electronic Stability Control Pump 30 Amp Pink –...
Page 385 IN CASE OF EMERGENCY 383 Cavity Cartridge Fuse Micro Fuse Description 30 Amp Pink – Anti-lock Brakes/Stability Control Module/Valves 20 Amp Blue – Trailer Tow Backup Lights — If Equipped 20 Amp Blue – Trailer Tow Parking Lights — If Equipped 30 Amp Pink –...
Page 386 384 IN CASE OF EMERGENCY Cavity Cartridge Fuse Micro Fuse Description – 20 Amp Yellow Trailer Tow – Left Turn/Stop Lights — If Equipped – 15 Amp Blue Additional Content (Diesel engine only) – 20 Amp Yellow NOX Sensor – 15 Amp Blue HID Headlamps LH —...
Page 387 IN CASE OF EMERGENCY 385 Cavity Cartridge Fuse Micro Fuse Description – 10 Amp Red Dual Batt Control — If Equipped – 10 Amp Red Anti-lock Brakes/Electronic Stability Control – 10 Amp Red Drivetrain Control Module/Front Axle Disconnect Module – 10 Amp Red Engine Control Module/Electric Power Steering –...
Page 388 386 IN CASE OF EMERGENCY Cavity Cartridge Fuse Micro Fuse Description – 10 Amp Red Shifter/Transfer Case Module – 10 Amp Red Rear Camera/ParkSense – 10 Amp Red Rear Seat Heater Switch/Flashlamp Charger — If Equipped – 20 Amp Yellow Rear Heated Seats &...
Page 389: Jacking And Tire Changing
IN CASE OF EMERGENCY 387 JACKING AND TIRE CHANGING CAUTION! WARNING! • When installing the power distribution center cover, it is important to ensure the cover is properly posi- • Do not attempt to change a tire on the side of the tioned and fully latched.
Page 390: Jack Location
388 IN CASE OF EMERGENCY Jack Location Rotate the plastic thumb screw on the end of the jack to loosen the jack and remove from the bracket. The scissor-type jack and tire changing tools are located in rear cargo area, below the load floor. Thumb Screw Location Jack Storage Location...
Page 391: Spare Tire Stowage
IN CASE OF EMERGENCY 389 Spare Tire Stowage CAUTION! The spare tire is stowed under the rear of the vehicle by The winch mechanism is designed for use with the means of a cable winch mechanism. To remove or stow the jack wrench extension tool only.
Page 392 390 IN CASE OF EMERGENCY 3. Fit the jack handle extension over the drive nut. Use the lug wrench handle and extension to completely lower the spare tire. Keep turning the handle until the winch stops. Spare Tire 5. Pull the metal stamping toward you to release it from the plastic plate.
Page 393 IN CASE OF EMERGENCY 391 6. Slide the metal stamping up the steel extension tube and 7. Pinch the three short and two long tubes to remove the winch cable. Rotate the metal stamping and push it protective plate from the steel spare wheel. through the hole in the plastic plate and wheel.
Page 394: Preparations For Jacking
392 IN CASE OF EMERGENCY Preparations For Jacking Jacking Instructions 1. Park the vehicle on a firm, level surface as far from the edge WARNING! of the roadway as possible. Avoid icy or slippery areas. Carefully follow these tire changing warnings to help WARNING! prevent personal injury or damage to your vehicle: •...
Page 395 IN CASE OF EMERGENCY 393 WARNING! (Continued) CAUTION! • If working on or near a roadway, be extremely Do not attempt to raise the vehicle by jacking on careful of motor traffic. locations other than those indicated in the Jacking •...
Page 396 394 IN CASE OF EMERGENCY 3. For the front tire, place the jack on the body flange just behind the front tire. Do not raise the vehicle until you are sure the jack is fully engaged. Rear Jacking Location 5. Raise the vehicle by turning the jack screw clockwise. Raise the vehicle just enough to remove the flat tire.
Page 397 IN CASE OF EMERGENCY 395 7. Install the spare wheel/tire on the vehicle and install the CAUTION! lug nuts with the cone-shaped end toward the wheel. Lightly tighten the nuts. Be sure to mount the spare tire with the valve stem facing outward.
Page 398 396 IN CASE OF EMERGENCY 10. Push out the small center cap using the jack tool from inside the aluminum road wheel and position the wheel behind the rear bumper with the protective plate facing outward. Installing Winch 12. Slide the road wheel on the ground using the protec- tive plate until it is directly under the winch and between the rear bumper and exhaust system heat shields.
Page 399 IN CASE OF EMERGENCY 397 13. Lower the jack to the fully closed position. Return the tools to the proper positions in the tool bag. Fold the flap on the tool bag under the tools and roll the tools in the bag underneath the others.
Page 400: Road Tire Installation
398 IN CASE OF EMERGENCY Road Tire Installation JUMP STARTING If your vehicle has a discharged battery, it can be jump 1. Mount the road tire on the axle. started using a set of jumper cables and a battery in another 2.
Page 401: Preparations For Jump Start
IN CASE OF EMERGENCY 399 Preparations For Jump Start WARNING! The battery in your vehicle is located under the passenger’s • Take care to avoid the radiator cooling fan whenever front seat. There are remote terminals located under the the hood is raised. It can start anytime the ignition hood to assist in jump starting.
Page 402: Jump Starting Procedure
400 IN CASE OF EMERGENCY 4. If using another vehicle to jump start the battery, park Connecting The Jumper Cables the vehicle within the jumper cables reach, apply the 1. Connect the positive (+) end of the jumper cable to the parking brake and make sure the ignition is OFF.
Page 403: If Your Engine Overheats
IN CASE OF EMERGENCY 401 If frequent jump starting is required to start your vehicle CAUTION! you should have the battery and charging system tested at an authorized dealer. Do not run the booster vehicle engine above 2000 rpm since it provides no charging benefit, wastes fuel and CAUTION! can damage booster vehicle engine.
Page 404: Manual Park Release
402 IN CASE OF EMERGENCY NOTE: There are steps that you can take to slow down an CAUTION! (Continued) impending overheat condition: over and stop the vehicle. Idle the vehicle with the air • If your air conditioner (A/C) is on, turn it off. The A/C conditioner turned off until the pointer drops back system adds heat to the engine cooling system and into the normal range.
Page 405 IN CASE OF EMERGENCY 403 In order to move the vehicle in cases where the transmis- 4. Using a screwdriver or similar tool, push the metal latch sion will not shift out of PARK (such as a dead battery), a in towards the tether strap.
Page 406 404 IN CASE OF EMERGENCY 5. While the metal latch is in the open position, simulta- NOTE: To prevent the vehicle from rolling unintentionally, neously pull upwards on the tether strap until the lever firmly apply the parking brake. clicks and latches in the released position. The transmis- To Disengage The Manual Park Release Lever: sion is now out of PARK and the vehicle can be moved.
Page 407: Freeing A Stuck Vehicle
IN CASE OF EMERGENCY 405 FREEING A STUCK VEHICLE 2. Once the tension has been released and the lever has been unlocked, be sure it is stowed properly and locks If your vehicle becomes stuck in mud, sand or snow, it can into position.
Page 408: Towing A Disabled Vehicle
406 IN CASE OF EMERGENCY WARNING! CAUTION! (Continued) • When “rocking” a stuck vehicle by shifting between Fast spinning tires can be dangerous. Forces generated DRIVE and REVERSE, do not spin the wheels faster by excessive wheel speeds may cause damage, or even than 15 mph (24 km/h), or drivetrain damage may failure, of the axle and tires.
Page 409 IN CASE OF EMERGENCY 407 Towing Con- Wheels OFF Rear-Wheel Drive Models All-Wheel All-Wheel Drive Models With dition The Ground Drive Models Two-Speed Transfer Case With Single- Speed Trans- fer Case Flat Tow NONE If Transmission Is Operable: See Instructions in “Recre- •...
Page 410: Rear Wheel Drive Models
408 IN CASE OF EMERGENCY Rear Wheel Drive Models Proper towing or lifting equipment is required to prevent damage to your vehicle. Use only tow bars and other The manufacturer recommends towing your vehicle with equipment designed for this purpose, following equipment all four wheels OFF the ground using a flatbed.
Page 411: All Wheel Drive Models
IN CASE OF EMERGENCY 409 Acceptable methods are to tow the vehicle on a flatbed, or CAUTION! with the front wheels raised and the rear wheels on a towing dolly, or (when using a suitable steering wheel • Front or rear wheel lifts must not be used (if the stabilizer to hold the front wheels in the straight position) remaining wheels are on the ground).
Page 412: Event Data Recorder (Edr)
410 IN CASE OF EMERGENCY EVENT DATA RECORDER (EDR) This vehicle is equipped with an Event Data Recorder (EDR). The main purpose of an EDR is to record data that will assist in understanding how a vehicle’s systems per- formed under certain crash or near crash-like situations, such as an air bag deployment or hitting a road obstacle.
Page 413 SERVICING AND MAINTENANCE CONTENTS SCHEDULED SERVICING ....413 ▫ Accessory Drive Belt Inspection ... .429 ▫...
Page 414 412 SERVICING AND MAINTENANCE ▫ Spare Tires — If Equipped ....462 BODYWORK ......469 ▫...
Page 415: Scheduled Servicing
SERVICING AND MAINTENANCE 413 SCHEDULED SERVICING Severe Duty All Models Your vehicle is equipped with an automatic oil change Change Engine Oil at 4,000 miles (6,500 km) or 350 hours of indicator system. The oil change indicator system will engine run time if the vehicle is operated in a dusty and off remind you that it is time to take your vehicle in for road environment or is operated predominately at idle or scheduled maintenance.
Page 416: Maintenance Plan
414 SERVICING AND MAINTENANCE Maintenance Plan Required Maintenance Refer to the Maintenance Plans on the following pages for required maintenance. At Every Oil Change Interval As Indicated By Oil Change Indicator System: • Change oil and filter. • Rotate the tires. Rotate at the first sign of irregular wear, even if it occurs before the oil indicator system turns on. •...
Page 417 SERVICING AND MAINTENANCE 415 Mileage or time passed (which- ever comes first) Or Years: Or Kilometers: Additional Inspections Inspect the CV joints. Inspect front suspension, tie rod ends, and replace if necessary. Inspect the front and rear axle fluid, change if using your vehicle for police, taxi, fleet, off-road or frequent trailer towing.
Page 418 416 SERVICING AND MAINTENANCE Mileage or time passed (which- ever comes first) Or Years: Or Kilometers: Flush and replace the engine cool- ant at 10 years or 150,000 miles (240,000 km) whichever comes first. Change transfer case fluid. Inspect and replace PCV valve if necessary.
Page 419: Heavy Duty Use Of The Vehicle
SERVICING AND MAINTENANCE 417 Heavy Duty Use Of The Vehicle ** The spark plug change interval is mileage based only, yearly intervals do not apply. Change engine oil at 4,000 miles (6,500 km) or 350 hours of engine run time if the vehicle is operated in a dusty and off WARNING! road environment or is operated predominately at idle or only very low engine RPM’s.
Page 420: Engine Compartment
418 SERVICING AND MAINTENANCE ENGINE COMPARTMENT 3.6L Engine 1 — Remote Jump Start Positive Terminal 6 — Brake Fluid Reservoir 2 — Power Distribution Center (Fuses) 7 — Air Cleaner Filter 3 — Coolant Pressure Cap (Reservoir) 8 — Washer Fluid Reservoir 4 —...
Page 421: L Engine
SERVICING AND MAINTENANCE 419 5.7L Engine 1 — Remote Jump Start Negative Terminal 6 — Air Cleaner Filter 2 — Remote Jump Start Positive Terminal 7 — Washer Fluid Reservoir 3 — Power Distribution Center (Fuses) 8 — Engine Oil Dipstick 4 —...
Page 422: Checking Oil Level
420 SERVICING AND MAINTENANCE Checking Oil Level The fluid reservoir for the windshield washers and the rear window washer is shared. The fluid reservoir is located in To assure proper lubrication of your vehicle’s engine, the the engine compartment, be sure to check the fluid level at engine oil must be maintained at the correct level.
Page 423: Maintenance-Free Battery
SERVICING AND MAINTENANCE 421 Maintenance-Free Battery CAUTION! Your vehicle is equipped with a maintenance-free battery. • It is essential when replacing the cables on the You will never have to add water, nor is periodic mainte- battery that the positive cable is attached to the nance required.
Page 424: Engine Oil
422 SERVICING AND MAINTENANCE American Petroleum Institute (API) Engine Oil WARNING! Identification Symbol You can be badly injured working on or around a motor vehicle. Only do service work for which you This symbol means that the oil has have the knowledge and the proper equipment. If you been certified by the American Pe- have any doubt about your ability to perform a service troleum Institute (API).
Page 425 SERVICING AND MAINTENANCE 423 Engine Oil Viscosity (SAE Grade) — 3.6L Engine NOTE: Vehicles equipped with a 5.7L engine must use SAE 5W-20 oil. Failure to do so may result in improper opera- Mopar SAE 0W-20 engine oil approved to FCA Material tion of the Fuel Saver Technology.
Page 426: Engine Oil Filter
424 SERVICING AND MAINTENANCE Disposing Of Used Engine Oil And Oil Filters NOTE: Be sure to follow the “Severe Duty Conditions” maintenance interval if applicable. Care should be taken in disposing of used engine oil and oil filters from your vehicle. Used oil and oil filters, WARNING! indiscriminately discarded, can present a problem to the environment.
Page 427: Air Conditioner Maintenance
SERVICING AND MAINTENANCE 425 Air Conditioner Maintenance CAUTION! For best possible performance, your air conditioner should Do not use chemical flushes in your air conditioning be checked and serviced by an authorized dealer at the system as the chemicals can damage your air condition- start of each warm season.
Page 428 426 SERVICING AND MAINTENANCE Refrigerant Recovery And Recycling — R–1234yf The A/C air filter is located in the fresh air inlet behind the glove compartment. Perform the following procedure to R–1234yf Air Conditioning Refrigerant is a hydrofluo- replace the filter: roolefin (HFO) that is endorsed by the Environmental Protection Agency and is an ozone-friendly substance with 1.
Page 429 SERVICING AND MAINTENANCE 427 2. There are glove compartment travel stops on both sides of the glove compartment door, partially close the glove compartment door and push inward to release the glove compartment travel stop on one side and repeat this procedure for the opposite side.
Page 430 428 SERVICING AND MAINTENANCE CAUTION! The cabin air filter is identified with an arrow to indicate airflow direction through the filter. Failure to properly install the filter will result in the need to replace it more often. 8. Reinstall the glove compartment door on the glove compartment door hinge and reattach the tension tether by inserting the tether clip in the glove compartment and sliding the clip away from the face of the glove...
Page 431: Accessory Drive Belt Inspection
SERVICING AND MAINTENANCE 429 Accessory Drive Belt Inspection WARNING! • Do not attempt to inspect an accessory drive belt with vehicle running. • When working near the radiator cooling fan, discon- nect the fan motor lead. The fan is temperature controlled and can start at any time regardless of ignition mode.
Page 432: Body Lubrication
430 SERVICING AND MAINTENANCE • Noise (objectionable squeal, squeak, or rumble is heard The external lock cylinders should be lubricated twice a or felt while drive belt is in operation) year, preferably in the Fall and Spring. Apply a small amount of a high quality lubricant, such as Mopar Lock Some conditions can be caused by a faulty component such Cylinder Lubricant directly into the lock cylinder.
Page 433 SERVICING AND MAINTENANCE 431 The wiper blades and wiper arms should be inspected periodically, not just when wiper performance problems are experienced. This inspection should include the follow- ing points: • Wear Or Uneven Edges • Foreign Material • Hardening Or Cracking •...
Page 434 432 SERVICING AND MAINTENANCE Wiper Blade With Release Tab In Unlocked Position Wiper Blade Removed From Wiper Arm 1 — Wiper Blade 1 — Wiper Blade 2 — Release Tab 2 — Wiper Arm 3 — Wiper Arm 3 — Release Tab 3.
Page 435 SERVICING AND MAINTENANCE 433 Installing The Front Wipers 1. Lift the wiper arm off of the glass, until the wiper arm is in the full up position. 2. Position the wiper blade near the hook on the tip of the wiper arm with the wiper release tab open and the blade side of the wiper facing up and away from the windshield.
Page 436 434 SERVICING AND MAINTENANCE NOTE: Resistance will be accompanied by an audible snap. 4. Still grasping the bottom end of the wiper blade, move the wiper blade upward and away from the wiper arm to disengage. Wiper Blade In Folded Out Position 1 —...
Page 437: Exhaust System
SERVICING AND MAINTENANCE 435 Installing The Rear Wiper If you notice a change in the sound of the exhaust system; or if the exhaust fumes can be detected inside the vehicle; 1. Lift the rear wiper arm pivot cap away from the glass to or when the underside or rear of the vehicle is damaged;...
Page 438 436 SERVICING AND MAINTENANCE NOTE: Intentional tampering with emissions control sys- CAUTION! tems can result in civil penalties being assessed against you. • The catalytic converter requires the use of unleaded fuel only. Leaded gasoline will destroy the effective- In unusual situations involving grossly malfunctioning ness of the catalyst as an emissions control device engine operation, a scorching odor may suggest severe and and may seriously reduce engine performance and...
Page 439: Cooling System
SERVICING AND MAINTENANCE 437 Cooling System Engine Coolant Checks Check the engine coolant (antifreeze) protection every 12 WARNING! months (before the onset of freezing weather, where appli- cable). If the engine coolant (antifreeze) is dirty, the system • Turn vehicle off and disconnect the fan motor lead should be drained, flushed, and refilled with fresh OAT before working near the radiator cooling fan.
Page 440 438 SERVICING AND MAINTENANCE If the engine coolant (antifreeze) is dirty or contains visible CAUTION! (Continued) sediment, have an authorized dealer clean and flush with • Do not use water alone or alcohol-based engine OAT coolant (antifreeze) (conforming to MS.90032). coolant (antifreeze) products.
Page 441 SERVICING AND MAINTENANCE 439 Please review these recommendations for using Organic NOTE: Additive Technology (OAT) engine coolant (antifreeze) • It is the owner’s responsibility to maintain the proper that meets the requirements of FCA Material Standard level of protection against freezing according to the MS.90032.
Page 442 440 SERVICING AND MAINTENANCE Cooling System Pressure Cap community. To prevent ingestion by animals or children, do not store ethylene glycol-based coolant in open contain- The cap must be fully tightened to prevent loss of engine ers or allow it to remain in puddles on the ground. If coolant (antifreeze), and to ensure that engine coolant ingested by a child or pet, seek emergency assistance (antifreeze) will return to the radiator from the coolant...
Page 443: Brake System
SERVICING AND MAINTENANCE 441 Points To Remember • Make sure that the coolant expansion bottle overflow hoses are not kinked or obstructed. NOTE: When the vehicle is stopped after a few miles/ • Keep the front of the radiator clean. If your vehicle is kilometers of operation, you may observe vapor coming equipped with air conditioning, keep the front of the from the front of the engine compartment.
Page 444 442 SERVICING AND MAINTENANCE Fluid Level Check — Brake Master Cylinder WARNING! (Continued) The fluid level of the master cylinder should be checked • To avoid contamination from foreign matter or mois- whenever the vehicle is serviced, or immediately if the brake ture, use only new brake fluid or fluid that has been system warning light is on.
Page 445: Automatic Transmission
SERVICING AND MAINTENANCE 443 Automatic Transmission Special Additives The manufacturer strongly recommends against using any Selection Of Lubricant special additives in the transmission. Automatic Transmis- It is important to use the proper transmission fluid to sion Fluid (ATF) is an engineered product and its perfor- ensure optimum transmission performance and life.
Page 446: Front/Rear Axle Fluid
444 SERVICING AND MAINTENANCE Front/Rear Axle Fluid transmission fluid level using special service tools. If you notice fluid leakage or transmission malfunction, visit an For normal service, periodic fluid level checks are not authorized dealer immediately to have the transmission required.
Page 447: Transfer Case
SERVICING AND MAINTENANCE 445 Rear Axle Fluid Level Check Adding Fluid The rear axle oil level needs to be no lower than 1/8 inch Add fluid at the filler hole, until it runs out of the hole, (3 mm) below the bottom of the fill hole. when the vehicle is in a level position.
Page 448: Tires
446 SERVICING AND MAINTENANCE TIRES NOTE: Tire Safety Information • P (Passenger) — Metric tire sizing is based on U.S. Tire safety information will cover aspects of the following design standards. P-Metric tires have the letter “P” information: Tire Markings, Tire Identification Numbers, Tire molded into the sidewall preceding the size designation.
Page 449 SERVICING AND MAINTENANCE 447 Tire Sizing Chart EXAMPLE: Example Size Designation: P215/65R15XL 95H, 215/65R15 96H, LT235/85R16C, T145/80D18 103M, 31x10.5 R15 LT P = Passenger car tire size based on U.S. design standards, or ..blank..= Passenger car tire based on European design standards, or LT = Light truck tire based on U.S.
Page 450 448 SERVICING AND MAINTENANCE EXAMPLE: H = Speed Symbol – A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under cer- tain operating conditions – The maximum speed corresponding to the speed symbol should only be achieved under specified operating condi- tions (i.e., tire pressure, vehicle loading, road conditions, and posted speed limits) Load Identification: Absence of the following load identification symbols on the sidewall of the tire indicates a Standard Load (SL) tire:...
Page 451 SERVICING AND MAINTENANCE 449 EXAMPLE: DOT MA L9 ABCD 0301 DOT = Department of Transportation – This symbol certifies that the tire is in compliance with the U.S. Department of Transportation tire safety standards and is approved for highway use MA = Code representing the tire manufacturing location (two digits) L9 = Code representing the tire size (two digits) ABCD = Code used by the tire manufacturer (one to four digits)
Page 452 450 SERVICING AND MAINTENANCE Tire Terminology And Definitions Term Definition B-Pillar The vehicle B-Pillar is the structural member of the body located be- hind the front door. Cold Tire Inflation Pressure Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least three hours, or driven less than 1 mile (1.6 km) after sitting for a minimum of three hours.
Page 453 SERVICING AND MAINTENANCE 451 Tire Loading And Tire Pressure NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar or the rear edge of the driver’s side door. Check the inflation pressure of each tire, including the spare tire (if equipped), at least monthly and inflate to the recommended pressure for your vehicle.
Page 454 452 SERVICING AND MAINTENANCE Tire And Loading Information Placard Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the Tire and Loading Information placard in “Vehicle Loading”...
Page 455 SERVICING AND MAINTENANCE 453 Steps For Determining Correct Load Limit— this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle. (1) Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or Metric Example For Load Limit XXX lbs.”...
Page 456 454 SERVICING AND MAINTENANCE WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the rec- ommended load capacity for your vehicle. Never over- load them.
Page 457: Tires - General Information
SERVICING AND MAINTENANCE 455 Tires — General Information WARNING! (Continued) Tire Pressure • Overinflated or underinflated tires can affect vehicle handling and can fail suddenly, resulting in loss of Proper tire inflation pressure is essential to the safe and vehicle control. satisfactory operation of your vehicle.
Page 458 456 SERVICING AND MAINTENANCE Fuel Economy CAUTION! Underinflated tires will increase tire rolling resistance After inspecting or adjusting the tire pressure, always resulting in higher fuel consumption. reinstall the valve stem cap. This will prevent moisture Tread Wear and dirt from entering the valve stem, which could damage the valve stem.
Page 459 SERVICING AND MAINTENANCE 457 pressure should be increased by 3 psi (21 kPa), which Radial Ply Tires equals 1 psi (7 kPa) for every 12°F (7°C) for this outside temperature condition. WARNING! Tire pressure may increase from 2 to 6 psi (13 to 40 kPa) Combining radial ply tires with other types of tires on during operation.
Page 460 458 SERVICING AND MAINTENANCE Run Flat Tires — If Equipped Refer to “Freeing A Stuck Vehicle” in “In Case Of Emer- gency” for further information. Run Flat tires allow you the capability to drive 50 miles (80 km) at 50 mph (80 km/h) after a rapid loss of inflation WARNING! pressure.
Page 461 SERVICING AND MAINTENANCE 459 Life Of Tire The service life of a tire is dependent upon varying factors including, but not limited to: • Driving style. • Tire pressure - Improper cold tire inflation pressures can cause uneven wear patterns to develop across the tire tread.
Page 462 460 SERVICING AND MAINTENANCE Keep dismounted tires in a cool, dry place with as little It is recommended you contact your authorized tire dealer exposure to light as possible. Protect tires from contact with or original equipment dealer with any questions you may oil, grease, and gasoline.
Page 463: Tire Types
SERVICING AND MAINTENANCE 461 Summer Or Three Season Tires — If Equipped WARNING! (Continued) Summer tires provide traction in both wet and dry condi- • Failure to equip your vehicle with tires having ad- tions, and are not intended to be driven in snow or on ice. equate speed capability can result in sudden tire If your vehicle is equipped with Summer tires, be aware failure and loss of vehicle control.
Page 464: Spare Tires - If Equipped
462 SERVICING AND MAINTENANCE Spare Tires — If Equipped Snow Tires Some areas of the country require the use of snow tires NOTE: For vehicles equipped with Tire Service Kit instead during the Winter. Snow tires can be identified by a of a spare tire, please refer to “Tire Service Kit”...
Page 465 SERVICING AND MAINTENANCE 463 Compact Spare Tire — If Equipped WARNING! (Continued) The compact spare is for temporary emergency use only. You more than 50 mph (80 km/h). Temporary use spares can identify if your vehicle is equipped with a compact spare have limited tread life.
Page 466 464 SERVICING AND MAINTENANCE Do not install a wheel cover or attempt to mount a Limited Use Spare — If Equipped conventional tire on the collapsible spare wheel, since the The limited use spare tire is for temporary emergency use wheel is designed specifically for the collapsible spare tire.
Page 467: Wheel And Wheel Trim Care
SERVICING AND MAINTENANCE 465 Wheel And Wheel Trim Care When cleaning extremely dirty wheels including excessive brake dust, care must be taken in the selection of tire and All wheels and wheel trim, especially aluminum and wheel cleaning chemicals and equipment to prevent dam- chrome plated wheels, should be cleaned regularly using age to the wheels.
Page 468: Tire Chains (Traction Devices)
466 SERVICING AND MAINTENANCE Dark Vapor Chrome, Black Satin Chrome, or Low Gloss WARNING! Clear Coat Wheels Using tires of different size and type (M+S, Snow) CAUTION! between front and rear axles can cause unpredictable handling. You could lose control and have a collision. If your vehicle is equipped with these specialty wheels, DO NOT USE wheel cleaners, abrasives, or CAUTION!
Page 469: Tire Rotation Recommendations
SERVICING AND MAINTENANCE 467 NOTE: The premium Tire Pressure Monitor System will CAUTION! (Continued) automatically locate the pressure values displayed in the • Observe the traction device manufacturer’s instruc- correct vehicle position following a tire rotation. tions on the method of installation, operating speed, The suggested rotation method is the “rearward-cross”...
Page 470: Department Of Transportation Uniform Tire Quality Grades
468 SERVICING AND MAINTENANCE DEPARTMENT OF TRANSPORTATION UNIFORM wet pavement, as measured under controlled conditions on TIRE QUALITY GRADES specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance. The following tire grading categories were established by the National Highway Traffic Safety Administration.
Page 471: Storing The Vehicle
SERVICING AND MAINTENANCE 469 BODYWORK WARNING! Protection From Atmospheric Agents The temperature grade for this tire is established for Vehicle body care requirements vary according to geographic a tire that is properly inflated and not overloaded. locations and usage. Chemicals that make roads passable in Excessive speed, under-inflation, or excessive load- snow and ice and those that are sprayed on trees and road ing, either separately or in combination, can cause...
Page 472: Body And Underbody Maintenance
470 SERVICING AND MAINTENANCE Preserving The Bodywork The most common causes are: • Road salt, dirt and moisture accumulation. Washing • Stone and gravel impact. • Wash your vehicle regularly. Always wash your vehicle in the shade using Mopar Car Wash, or a mild car wash •...
Page 473: Interiors
SERVICING AND MAINTENANCE 471 INTERIORS Special Care • If you drive on salted or dusty roads or if you drive near Seats And Fabric Parts the ocean, hose off the undercarriage at least once a Use Mopar Total Clean to clean fabric upholstery and month.
Page 474: Plastic And Coated Parts
472 SERVICING AND MAINTENANCE Cleaning Plastic Instrument Cluster Lenses WARNING! The lenses in front of the instruments in this vehicle are A frayed or torn belt could rip apart in a collision and molded in clear plastic. When cleaning the lenses, care leave you with no protection.
Page 475: Glass Surfaces
SERVICING AND MAINTENANCE 473 Glass Surfaces leather upholstery with any liquid. Please do not use polishes, oils, cleaning fluids, solvents, detergents, or All glass surfaces should be cleaned on a regular basis with ammonia-based cleaners to clean your leather upholstery. Mopar Glass Cleaner, or any commercial household-type Application of a leather conditioner is not required to glass cleaner.
Page 477 TECHNICAL SPECIFICATIONS CONTENTS IDENTIFICATION DATA....476 ▫ Gasoline/Oxygenate Blends ....481 ▫...
Page 478: Identification Data
476 TECHNICAL SPECIFICATIONS IDENTIFICATION DATA Vehicle Identification Number The Vehicle Identification Number (VIN) is found on a label located on the left front corner of the instrument panel pad, visible from outside of the vehicle through the wind- shield. This number also is stamped on the right front floor, behind the right front seat.
Page 479: Brake System
TECHNICAL SPECIFICATIONS 477 In the event power assist is lost for any reason (i.e., repeated brake applications with the engine off) the brakes will still function. However, the effort required to brake the vehicle will be much greater than that required with the power system operating.
Page 480 478 TECHNICAL SPECIFICATIONS Inspect the wheel mounting surface prior to mounting the After 25 miles (40 km), check the lug nut/bolt torque to be tire and remove any corrosion or loose particles. sure that all the lug nuts/bolts are properly seated against the wheel.
Page 481: Fuel Requirements
TECHNICAL SPECIFICATIONS 479 FUEL REQUIREMENTS Poor quality gasoline can cause problems such as hard starting, stalling, and hesitations. If you experience these 3.6L Engine symptoms, try another brand of gasoline before consider- Do not use E-85 flex fuel or ethanol blends greater than ing service for the vehicle.
Page 482: Reformulated Gasoline
480 TECHNICAL SPECIFICATIONS Materials Added To Fuel Use of gasoline with an octane number lower than 87 can cause engine failure and may void or not be covered by the Besides using unleaded gasoline with the proper octane New Vehicle Limited Warranty. rating, gasolines that contain detergents, corrosion and Poor quality gasoline can cause problems such as hard stability additives are recommended.
Page 483: Gasoline/Oxygenate Blends
TECHNICAL SPECIFICATIONS 481 Gasoline/Oxygenate Blends Do Not Use E-85 In Non-Flex Fuel Vehicles Some fuel suppliers blend unleaded gasoline with oxygen- Non-Flex Fuel Vehicles (FFV) are compatible with gasoline ates such as ethanol. containing up to 15% ethanol (E-15). Use of gasoline with higher ethanol content may void the New Vehicle Limited CAUTION! Warranty.
Page 484: Mmt In Gasoline
482 TECHNICAL SPECIFICATIONS MMT In Gasoline CAUTION! (Continued) Methylcyclopentadienyl Manganese Tricarbonyl (MMT) is • An out-of-tune engine or certain fuel or ignition a manganese-containing metallic additive that is blended malfunctions can cause the catalytic converter to into some gasoline to increase octane. Gasoline blended overheat.
Page 485: Carbon Monoxide Warnings
TECHNICAL SPECIFICATIONS 483 Carbon Monoxide Warnings WARNING! (Continued) engine running for an extended period. If the vehicle WARNING! is stopped in an open area with the engine running Carbon monoxide (CO) in exhaust gases is deadly. for more than a short period, adjust the ventilation Follow the precautions below to prevent carbon mon- system to force fresh, outside air into the vehicle.
Page 486 484 TECHNICAL SPECIFICATIONS U.S. Metric Cooling System * 3.6L Engine (Mopar Antifreeze/Engine Coolant 10 Year/ 10.4 Quarts 9.9 Liters 150,000 Mile Formula or equivalent) – Without Trailer Tow Package 3.6L Engine (Mopar Antifreeze/Engine Coolant 10 Year/ 11 Quarts 10.4 Liters 150,000 Mile Formula or equivalent) –...
Page 487: Fluids And Lubricants
TECHNICAL SPECIFICATIONS 485 FLUIDS AND LUBRICANTS Engine Component Fluid, Lubricant, or Genuine Part Engine Coolant We recommend you use Mopar Antifreeze/Coolant 10 Year/150,000 Mile Formula OAT (Organic Additive Technology) meeting the requirements of FCA Material Standard MS.90032. Engine Oil – 3.6L Engine We recommend you use API Certified SAE 0W-20 Engine Oil, meeting the requirements of FCA Material Standard MS-6395 such as Mopar, Pennzoil, Shell Helix or equivalent.
Page 488 486 TECHNICAL SPECIFICATIONS CAUTION! CAUTION! (Continued) (conforming to MS.90032), by an authorized dealer as • Mixing of engine coolant (antifreeze) other than speci- soon as possible. fied Organic Additive Technology (OAT) engine coolant • Do not use water alone or alcohol-based engine (antifreeze), may result in engine damage and may coolant (antifreeze) products.
Page 489: Chassis
TECHNICAL SPECIFICATIONS 487 Chassis Component Fluid, Lubricant, or Genuine Part Automatic Transmission Use only Mopar ZF 8&9 Speed ATF Automatic Transmis- sion Fluid or equivalent. Failure to use the correct fluid may affect the function or performance of your transmis- sion.
Page 491: Multimedia
MULTIMEDIA CONTENTS UCONNECT RADIOS ....491 ▫ Second Row USB Charging Port ... .534 PERSONALIZED MENU BAR .
Page 492 490 MULTIMEDIA ▫ Accessibility — If Equipped ....545 ▫ Navigation (4C NAV) ....559 ▫...
Page 493: Uconnect Radios
MULTIMEDIA UCONNECT RADIOS For detailed information about your Uconnect radio, refer to your Uconnect Owner’s Manual Supplement. NOTE: Uconnect screen images are for illustration pur- poses only and may not reflect exact software for your vehicle. PERSONALIZED MENU BAR The Uconnect features and services in the main menu bar are easily changed for your convenience.
Page 494: Cybersecurity
492 MULTIMEDIA CYBERSECURITY WARNING! Your vehicle may be a connected vehicle and may be • It is not possible to know or to predict all of the equipped with both wired and wireless networks. These possible outcomes if your vehicle’s systems are networks allow your vehicle to send and receive informa- breached.
Page 495: Uconnect Settings
MULTIMEDIA UCONNECT SETTINGS NOTE: • FCA US LLC or your dealer may contact you directly The Uconnect system uses a combination of buttons on the regarding software updates. touchscreen and buttons on the faceplate located on the center of the instrument panel that allow you to access and •...
Page 496: Customer Programmable Features
494 MULTIMEDIA equipped such as Display, Voice, Clock & Date, Safety & Assistance, Lights, Doors & Locks, Auto-On Comfort, Engine Off Options, Compass Settings, Audio, Phone/ Bluetooth, Sirius Setup, Restore Settings, Clear Personal Data, and System Information. When making a selection, press the button on the touch- screen to enter the desired mode.
Page 497 MULTIMEDIA Display After pressing the “Display” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Display Mode Manual Auto Display Brightness With Headlights ON NOTE: To make changes to the Display Brightness with Headlights ON setting, the headlights must be on and the interior dimmer switch must not be in the party or parade positions.
Page 498 496 MULTIMEDIA Setting Name Selectable Options Set Language NOTE: When the “Set Language” feature is selected, you may select one of multiple languages (English/Français/Español) for all display nomenclature, including the trip functions and the navigation system (if equipped). Press the “Set Lan- guage”...
Page 499 MULTIMEDIA Voice After pressing the “Voice” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Voice Response Length Brief Detailed Show Command List Always With Help Never Clock & Date After pressing the “Clock & Date” button on the touch- screen, the following settings will be available: Setting Name Selectable Options...
Page 500 498 MULTIMEDIA Safety/Assistance After pressing the “Safety/Assistance” button on the touchscreen, the following settings will be available: Setting Name Selectable Options ParkView Backup Camera Delay — If Equipped NOTE: The “ParkView Backup Camera Delay” setting determines whether or not the screen will display the rear view image with dynamic grid lines for up to ten seconds after the vehicle is shifted out of REVERSE.
Page 501 MULTIMEDIA Setting Name Selectable Options Forward Collision Warn- Warning Only Warning & Braking ing — If Equipped NOTE: Changing the FCW status to “Off” prevents the system from warning you of a possible collision with the vehicle in front of you. The FCW system state is kept in memory from one ignition cycle to the next.
Page 502 500 MULTIMEDIA Setting Name Selectable Options ParkSense — If Equipped Sound Only Sound and Display NOTE: The “ParkSense” system setting will scan for objects behind the vehicle when the transmission gear selector is in REVERSE and the vehicle speed is less than 7 mph (11 km/h), when enabled. It will provide an alert (audible and/or visual) to indi- cate the proximity to other objects.
Page 503 MULTIMEDIA Setting Name Selectable Options Blind Spot Alert — If Lights Lights and Chime Equipped NOTE: When the “Blind Spot Alert” feature is selected, the Blind Spot Monitor (BSM) system is activated and will show a visual alert in the outside mirrors, or it will show a visual alert in the outside mirrors as well as play an audible alert when the turn signal is on.
Page 504 502 MULTIMEDIA Lights After pressing the “Lights” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Headlight Off Delay 0 sec 30 sec 60 sec 90 sec NOTE: When the “Headlight Off Delay” feature is selected, it allows the adjustment of the amount of time the headlights remain on after the engine is shut off.
Page 505 MULTIMEDIA Setting Name Selectable Options Daytime Running Lights Flash Lights With Lock Doors & Locks After pressing the “Doors & Locks” button on the touch- screen, the following settings will be available: Setting Name Selectable Options Auto Door Locks NOTE: The “Auto Door Locks”...
Page 506 504 MULTIMEDIA Setting Name Selectable Options Passive Entry Remote Door Unlock/Door Driver Unlock NOTE: When “Driver” is selected, only the driver’s door will unlock on the first push of the key fob unlock button, you must push the key fob unlock button twice to unlock the passenger’s doors. When “All” is selected, all of the doors will unlock on the first press of the key fob unlock button.
Page 507 MULTIMEDIA Auto Comfort Systems — If Equipped After pressing the “Auto-On Comfort & Remote Start” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Auto-On Driver Heated/ Remote Start All Starts Ventilated Seat & Steering Wheel With Vehicle Start —...
Page 508 506 MULTIMEDIA Engine Off Options After pressing the “Engine Off Options” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Engine Off Power 0 sec 45 sec 5 min 10 min Delay — If Equipped NOTE: When the “Engine Off Power Delay”...
Page 509 MULTIMEDIA Audio After pressing the “Audio” button on the touchscreen, the following settings will be available: Setting Name Adjustable Options Equalizer Bass Treble NOTE: When in this display you may adjust the “Bass”, “Mid” and “Treble” settings. Adjust the settings with the “+” and “–”...
Page 510 508 MULTIMEDIA Setting Name Adjustable Options AUX Volume Offset — If Equipped NOTE: This feature provides the ability to tune the audio level for portable devices connected through the AUX input Phone/Bluetooth After pressing the “Phone/Bluetooth” button on the touch- screen, the following settings will be available: Setting Name Selectable Options...
Page 511 MULTIMEDIA SiriusXM Setup — If Equipped After pressing the “SiriusXM Setup” button on the touch- screen, the following settings will be available: Setting Name Selectable Options Channel Skip List of Channels NOTE: SiriusXM can be programmed to designate a group of channels that are the most desirable to listen to or to exclude undesirable channels while scanning.
Page 512 510 MULTIMEDIA Restore Settings After pressing the “Restore Settings” button on the touch- screen, the following settings will be available: Setting Name Selectable Options Restore Settings Cancel NOTE: When this feature is selected, it will reset all settings to their default settings. To restore the settings to their default setting, press the “Restore Settings”...
Page 513: Customer Programmable Features - Uconnect 4C/4C Nav Settings
MULTIMEDIA System Information After pressing the “System Information” button on the touchscreen, the following settings will be available: Setting Name Selectable Options System Information System Software Information Screen NOTE: When the “System Information” feature is selected, a “System Software Information” screen will appear, displaying the system software version.
Page 514 512 MULTIMEDIA Display After pressing the “Display” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Display Mode Manual Auto Display Brightness With Headlights ON NOTE: To make changes to the Display Brightness with Headlights ON setting, the headlights must be on and the interior dimmer switch must not be in the party or parade positions.
Page 515 MULTIMEDIA Setting Name Selectable Options Set Language NOTE: When the “Set Language” feature is selected, you may select one of multiple languages (English / Français / Espa- ñol) for all display nomenclature, including the trip functions and the navigation system (if equipped). Press the “Set Language”...
Page 516 514 MULTIMEDIA Units After pressing the “Units” button on the touchscreen, you may select each unit of measure independently displayed in the instrument cluster display, and navigation system (if equipped). The following selectable units of measure are listed below: Setting Name Selectable Options Units Metric...
Page 517 MULTIMEDIA Clock After pressing the “Clock” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Sync Time With GPS Set Time Hours NOTE: The “Set Time Hours” feature will allow you to adjust the hours. The “Sync time with GPS” button on the touch- screen must be unchecked.
Page 518 516 MULTIMEDIA Safety & Driving Assistance After pressing the “Safety/Assistance” button on the touchscreen, the following settings will be available: Setting Name Selectable Options ParkView Backup Camera Delay — If Equipped NOTE: The “ParkView Backup Camera Delay” setting determines whether or not the screen will display the rear view image with dynamic grid lines for up to ten seconds after the vehicle is shifted out of REVERSE.
Page 519 MULTIMEDIA Setting Name Selectable Options Forward Collision Warn- Warning Only Warning & Braking ing — If Equipped NOTE: Changing the FCW status to “Off” prevents the system from warning you of a possible collision with the vehicle in front of you. The FCW system state is kept in memory from one ignition cycle to the next.
Page 520 518 MULTIMEDIA Setting Name Selectable Options ParkSense — If Equipped Sound Only Sound and Display NOTE: The “ParkSense” system setting will scan for objects behind the vehicle when the transmission gear selector is in REVERSE and the vehicle speed is less than 7 mph (11 km/h), when enabled. It will provide an alert (audible and/or visual) to indi- cate the proximity to other objects.
Page 521 MULTIMEDIA Setting Name Selectable Options LaneSense Strength — If Medium High Equipped Blind Spot Alert — If Lights Lights and Chime Equipped NOTE: When the “Blind Spot Alert” feature is selected, the Blind Spot Alert system is activated and will show a visual alert in the outside mirrors, or it will show a visual alert in the outside mirrors as well as play an audible alert when the turn signal is on.
Page 522 520 MULTIMEDIA Lights After pressing the “Lights” button on the touchscreen, the following settings will be available. Setting Name Selectable Options Headlight Off Delay 0 sec 30 sec 60 sec 90 sec NOTE: When the “Headlight Off Delay” feature is selected, it allows the adjustment of the amount of time the headlights remain on after the engine is shut off.
Page 523 MULTIMEDIA Setting Name Selectable Options Auto Dim High Beams— If Equipped NOTE: When the “Auto Dim High Beams” feature is selected, the high beam headlights will activate/deactivate automati- cally under certain conditions. Daytime Running Lights — If Equipped Flash Lights With Lock Doors &...
Page 524 522 MULTIMEDIA Setting Name Selectable Options Auto Unlock On Exit NOTE: When this feature is selected, all doors will unlock when the vehicle is stopped, the transmission is in the PARK or NEUTRAL position and the driver’s door is opened. Flash Lights With Lock Sound Horn With Lock 1st Press...
Page 525 MULTIMEDIA Setting Name Selectable Options Passive Entry — If Equipped NOTE: This feature allows you to lock and unlock the vehicles door(s) without having to push the key fob lock or unlock buttons. Personal Settings Linked to Key Fob — If Equipped NOTE: This feature provides automatic recall of all settings stored to a memory location (driver’s seat, exterior mirrors, steer-...
Page 526 524 MULTIMEDIA Auto-On Comfort — If Equipped After pressing the “Auto-On Comfort” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Auto-On Driver Heated/ Remote Start All Starts Vented & Steering Wheel With Vehicle Start — If Equipped NOTE: When this feature is selected the driver’s heated seat and heated steering wheel will automatically turn ON when...
Page 527 MULTIMEDIA Engine Off Options After pressing the “Engine Off Options” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Engine Off Power 0 sec 45 sec 5 min 10 min Delay — If Equipped NOTE: When the “Engine Off Power Delay”...
Page 528 526 MULTIMEDIA Audio After pressing the “Audio” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Balance/Fade Speaker Icon NOTE: When in this display you may adjust the “Balance/Fade” of the audio by pressing and dragging the “Speaker Icon” toward any location in the box.
Page 529 MULTIMEDIA Phone Settings After pressing the “Phone Settings” button on the touch- screen, the following settings will be available: Setting Name Selectable Options Do Not Disturb List of Settings NOTE: Press “Do Not Disturb” to access the available settings. The following settings are: Auto Reply (both, text, call), Auto Reply Message (custom, default) and Custom Auto Reply Message (create message).
Page 530 528 MULTIMEDIA SiriusXM Setup — If Equipped After pressing the “SiriusXM Setup” button on the touch- screen, the following settings will be available: Setting Name Selectable Options Tune Start NOTE: The “Tune Start” feature begins playing the current song from the beginning when you tune to a music channel using one of the twelve presets, so you can enjoy the complete song.
Page 531 MULTIMEDIA Setting Name Selectable Options Subscription Info Sirius ID NOTE: New vehicle purchasers or lessees will receive a free limited time subscription to SiriusXM Satellite Radio with your radio. Following the expiration of the free services, it will be necessary to access the information on the Subscription Information screen to re-subscribe.
Page 532 530 MULTIMEDIA Restore Settings After pressing the “Restore Settings” button on the touch- screen, the following settings will be available: Setting Name Selectable Options Restore Settings Cancel NOTE: When this feature is selected, it will reset all settings to their default settings. To restore the settings to their default setting, press the “Restore Settings”...
Page 533: Steering Wheel Audio Controls - If
MULTIMEDIA System Information After pressing the “System Information” button on the touchscreen, the following settings will be available: Setting Name Selectable Options System Information System Software Information Screen NOTE: When the “System Information” feature is selected, a “System Software Information” screen will appear, displaying the system software version.
Page 534: Radio Operation
532 MULTIMEDIA CD Player The right-hand control is a rocker-type switch with a push-button in the center and controls the volume and Pushing the top of the switch once will go to the next track mode of the sound system. Pushing the top of the rocker on the CD.
Page 535: Connecting The Ipod Or External Usb Device
MULTIMEDIA Connecting The iPod Or External USB Device Once the audio device is connected and synchronized to the vehicles iPod/USB/MP3 control system (iPod or exter- Use the connection cable to connect an iPod or external nal USB device may take a few minutes to connect), the USB device to the vehicles USB/AUX connector port which audio device starts charging and is ready for use.
Page 536: Second Row Usb Charging Port
534 MULTIMEDIA Second Row USB Charging Port Second row USB connector ports can be used for charging purposes only. Use the connection cable to connect an iPod or external USB device to the vehicle’s USB charging ports which are located either on the rear of the front center console and/or in the second row center console.
Page 537: Getting Started
MULTIMEDIA Getting Started • Turn on the Rear Seat Entertainment system by pushing the power button on the remote control. • Screen(s) located in the rear of front seats: Open the LCD screen cover by lifting up on cover. • When the Video Screen(s) are open and a DVD/Blu-ray disc is inserted into the disc player, the screen(s) turn(s) on automatically, the headphone transmitters turn on and playback begins.
Page 538: Dual Video Screen
536 MULTIMEDIA • With the Dual Video Screen System, Channel 1 (Rear 1) on the remote control and headphones, refers to Screen 1 (driver’s side) and Channel 2 (Rear 2) on the Remote Control and Headphones refers to Screen 2 (passenger side).
Page 539: Blu-Ray Disc Player
MULTIMEDIA Blu-ray Disc Player 2. To watch a Blu-ray disc on Rear 1 for driver’s side rear passengers, ensure the Remote Control and Headphone Play A Blu-ray Disc switch is on Rear 1. The Blu-ray disc player is located in the center console. 3.
Page 540 538 MULTIMEDIA Using The Touchscreen Radio 3. RSE Mute Mute rear headphones for the current ignition cycle. Press- ing mute again will unmute rear headphones. 4. RSE Remote Control Lock Out Press to enable/disable remote control functions. 5. RSE Channel 2 Mode Indicates the current source for Screen 2/Channel 2.
Page 541: Play Video Games
MULTIMEDIA 8. RSE Mode Select this button to change source for the active (highlighted) rear Screen/Channel on the rear media control screen. • Press the Media button on the touchscreen, and then press the rear media button on the touchscreen. •...
Page 542: Play A Dvd/Blu-Ray Disc Using The Touchscreen Radio
540 MULTIMEDIA Play A DVD/Blu-ray Disc Using The Touchscreen Radio 1. Insert the DVD/Blu-ray Disc with the label facing as indicated on the DVD/Blu-ray Disc player. The radio automatically selects the appropriate mode after the disc is recognized and displays the menu screen or starts playing the first track.
Page 543 MULTIMEDIA Rear Media Control Screen Rear Seat Entertainment Source Screen 3. Press the 1 or 2 buttons on the touchscreen, and the NOTE: Pressing the screen on the radio while a DVD or select source button on the touchscreen. Press the DISC Blu-ray Disc is playing, brings up the basic remote control button on the touchscreen in the MEDIA column.
Page 544: Important Notes For Dual Video Screen System
542 MULTIMEDIA Important Notes For Dual Video Screen System Blu-ray Disc Player Remote Control — If Equipped • The Rear Seat Entertainment System is able to transmit two channels of stereo audio and video simultaneously. • The Blu-ray Disc Player can play CDs, DVDs and Blu-ray Discs.
Page 545 MULTIMEDIA 3. SOURCE — Push to enter Source Selection screen. 11. KEYPAD — Push to navigate chapters or titles. 4. Channel/Screen Selector Switch — Indicates which 12. ▪ (Stop) — Stops disc play. channel is being controlled by the remote control. When —...
Page 546: Headphones Operation
544 MULTIMEDIA Headphones Operation Controls The headphones receive two separate channels of audio The headphone power indicator and controls are located using an infrared transmitter from the video screen. on the right ear cup. If no audio is heard after increasing the volume control, NOTE: The rear video system must be turned on before verify that the screen is turned on, the channel is not muted sound can be heard from the headphones.
Page 547: Replacing The Headphone Batteries
MULTIMEDIA Unwired Stereo Headphone Lifetime Limited 3. Pushing the SOURCE button will advance to the next mode. Warranty Who Does This Warranty Cover? This warranty covers the 4. When the Mode Selection menu appears on screen, use initial user or purchaser ( you or your ) of this particular the cursor buttons on the remote control to navigate to Unwired Technology LLC ( Unwired ) wireless headphone the available modes and push the OK button to select...
Page 548 546 MULTIMEDIA states and jurisdictions may not allow the exclusion or System Information limitation of incidental or consequential damages, so the Disc Menu above limitation may not apply to you. This warranty gives When listening to a CD Audio or CD Data disc, pushing you specific legal rights.
Page 549 MULTIMEDIA video on the screen. The factory default settings are already • When the screen is reopened, the video screen will set for optimum viewing, so there is no need to change automatically turn back on and show the appropriate these settings under normal circumstances.
Page 550 548 MULTIMEDIA DVD Region Codes If you record a disc using a personal computer, there may be cases where the Blu-ray Disc player may not be able to The Blu-ray Disc player and many DVD discs are coded by play some or the entire disc, even if it is recorded in a geographic region.
Page 551 MULTIMEDIA The recommended method for labeling recordable discs • Other compression formats such as AAC, MP3 Pro, Ogg (CD-R, CD-RW, and DVD-R) is with a permanent marker. Vorbis, and ATRAC3 will not play. The Blu-ray player Do not use adhesive labels as they may separate from the will automatically skip the file and begin playing the disc, become stuck, and cause permanent damage to the next available file.
Page 552: Radio Operation And Mobile Phones
550 MULTIMEDIA RADIO OPERATION AND MOBILE PHONES the disc is reached, the Blu-ray Disc player will return to the beginning of the disc and attempt to play the start of Under certain conditions, the mobile phone being on in the first track. your vehicle can cause erratic or noisy performance from your radio.
Page 553 MULTIMEDIA The radio manufacturer believes the internal wireless radio NOTE: is safe for use by consumers. The level of energy emitted is • This equipment has been tested and found to comply far less than the electromagnetic energy emitted by wire- with the limits for a Class B digital device, pursuant to less devices such as mobile phones.
Page 554: Voice Commands
552 MULTIMEDIA VOICE COMMANDS Introducing Uconnect Start using Uconnect Voice Recognition with these helpful quick tips. It provides the key Voice Commands and tips you need to know to control your Uconnect system. Uconnect 4C NAV NOTE: If you see the NAV icon on the bottom bar, or in the Apps menus, of your touchscreen, you have the Uconnect Uconnect 4 4C NAV system.
Page 555: Get Started
MULTIMEDIA Get Started All you need to control your Uconnect system with your voice are the buttons on your steering wheel. See below for helpful hints when using Voice Recognition: 1. Visit UconnectPhone.com to check mobile device and feature compatibility and to find phone pairing instruc- tions.
Page 556: Basic Voice Commands
554 MULTIMEDIA Basic Voice Commands The basic Voice Commands below can be given at any point while using your Uconnect system. Push the VR button . After the beep, say: • “Cancel” to stop a current voice session • “Help” to hear a list of suggested Voice Commands •...
Page 557 MULTIMEDIA TIP: At any time, if you are not sure of what to say or want to learn a Voice Command, push the VR button and say “Help.” The system will provide you with a list of commands. Uconnect 4C/4C NAV Radio Uconnect 4 Radio...
Page 558: Media
556 MULTIMEDIA Media Uconnect offers connections via USB, Bluetooth and auxil- iary ports (If Equipped). Voice operation is only available for connected USB and AUX devices. (Remote CD player optional and not available on all vehicles.) Push the VR button .
Page 559: Phone
MULTIMEDIA • “ Call John Smith” • “ Dial 123-456-7890 and follow the system prompts” • “ Redial (call previous outgoing phone number)” • “ Call back (call previous incoming phone number)” TIP: When providing a Voice Command, push the Phone button and say “Call,”...
Page 560: Climate (4C/4C Nav)
558 MULTIMEDIA • “ Set passenger temperature to 70 degrees” TIP: Voice Command for Climate may only be used to adjust the interior temperature of your vehicle. Voice Command will not work to adjust the heated seats or steering wheel if equipped. Uconnect 4C/4C NAV Phone Climate (4C/4C NAV) Too hot? Too cold? Adjust vehicle temperatures hands-free...
Page 561: Navigation (4C Nav)
MULTIMEDIA Navigation (4C NAV) The Uconnect navigation feature helps you save time and become more productive when you do not know exactly how to get to where you want to go. (Navigation is optional on the Uconnect 4C system.) 1. To enter a destination, push the VR button .
Page 562: Siriusxm Guardian (4C Nav) - If Equipped
560 MULTIMEDIA SiriusXM Guardian (4C NAV) — If Equipped Send & Go Vehicle Finder CAUTION! Stolen Vehicle Assistance Some SiriusXM Guardian services, including SOS Call Remote Vehicle Start** and Roadside Assistance Call will NOT work without an operable LTE (voice/data) or 3G or 4G (data) net- Remote Horn &...
Page 563: Mobile App (4C Nav)
MULTIMEDIA 3. Select “Customer Care” to speak with a SiriusXM To use the Uconnect App: Guardian Customer Care agent who will activate ser- • Download the Uconnect App to your mobile device. vices in your vehicle, or select “Enter Email” to activate •...
Page 564: Apple Carplay - If Equipped
562 MULTIMEDIA Apple CarPlay — If Equipped Push the VR button . After the beep, say one of the following commands: Apple CarPlay allows you to use your voice to interact • Show fuel prices with Siri through your vehicle’s voice recognition system, and use your smartphone’s data plan to project your •...
Page 565 MULTIMEDIA Uconnect 4 Apple CarPlay Uconnect 4C/4C NAV Apple CarPlay Refer to your Uconnect Owner’s Manual Supplement for further information.
Page 566: Android Auto - If Equipped
564 MULTIMEDIA Android Auto — If Equipped Android Auto allows you to use your voice to interact with Android’s best-in-class speech technology through your vehicle’s voice recognition system, and use your smart- phone’s data plan to project your Android powered smart- phone and a number of its apps onto your Uconnect touchscreen.
Page 567: General Information
MULTIMEDIA General Information The following regulatory statement applies to all Radio Frequency (RF) devices equipped in this vehicle: This device complies with Part 15 of the FCC Rules and with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: 1.
Page 568: Additional Information
566 MULTIMEDIA Additional Information CD/DVD DISC MAINTENANCE © 2017 FCA US LLC. All rights reserved. Mopar and To keep a CD/DVD in good condition, take the following Uconnect are registered trademarks and Mopar Owner precautions: Connect is a trademark of FCA US LLC. Android is a 1.
Page 569 CUSTOMER ASSISTANCE CONTENTS SUGGESTIONS FOR OBTAINING SERVICE FOR ▫ Customer Assistance For The Hearing Or Speech YOUR VEHICLE ......568 Impaired (TDD/TTY) .
Page 570: Suggestions For Obtaining Service For Your Vehicle
568 CUSTOMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR IF YOU NEED ASSISTANCE YOUR VEHICLE The manufacturer and its authorized dealer are vitally interested in your satisfaction. We want you to be happy Prepare For The Appointment with our products and services. If you are having warranty work done, be sure to have the right papers with you.
Page 571: Fca Us Llc Customer Center
CUSTOMER ASSISTANCE 569 In Mexico Contact Any communication to the manufacturer’s customer center should include the following information: Av. Prolongacion Paseo de la Reforma, 1240 • Owner’s name and address Sante Fe C.P. 05109 • Owner’s telephone number (home and office) Mexico, D.
Page 572: Customer Assistance For The Hearing Or Speech Impaired (Tdd/Tty)
570 CUSTOMER ASSISTANCE Customer Assistance For The Hearing Or Speech and an Owner Identification Card in the mail within three Impaired (TDD/TTY) weeks of the vehicle delivery date. If you have any questions about the service contract, call the manufactur- To assist customers who have hearing difficulties, the er’s Service Contract National Customer Hotline at 1-800- manufacturer has installed special TDD (Telecommunica-...
Page 573: Warranty Information
CUSTOMER ASSISTANCE 571 REPORTING SAFETY DEFECTS WARNING! In The 50 United States And Washington, D.C. Engine exhaust (internal combustion engines only), If you believe that your vehicle has a defect that could some of its constituents, and certain vehicle compo- cause a crash or cause injury or death, you should nents contain, or emit, chemicals known to the State of immediately inform the National Highway Traffic...
Page 574: In Canada
572 CUSTOMER ASSISTANCE In Canada Diagnostic Procedure Manuals If you believe that your vehicle has a safety defect, you Diagnostic Procedure Manuals are filled with diagrams, should contact the Customer Service Department imme- charts and detailed illustrations. These practical manuals diately.
Page 575 INDEX...
Page 576 574 INDEX About Your Brakes ......477 Air Conditioner Maintenance ....425 Adaptive Cruise Control (ACC) (Cruise Control) .
Page 577 INDEX 575 Automatic High Beams ..... . .78 Anti-Lock (ABS) ......477 Automatic Temperature Control (ATC) .
Page 578 576 INDEX Chains, Tire ......466 Compact Spare Tire ......463 Changing A Flat Tire .
Page 579 INDEX 577 Disposal Hazard Warning Flasher ....370 Antifreeze (Engine Coolant) ....440 Jacking .
Page 580 578 INDEX Enhanced Accident Response Feature ..227, 409 Forward Collision Warning....193 Ethanol........481 Four-Way Hazard Flasher.
Page 581 INDEX 579 Gross Axle Weight Rating.....347 Key Fob Not Detected ..... .26 Gross Vehicle Weight Rating .
Page 582 580 INDEX Arm The Alarm ......33 Light Bulbs .......257 Disarm The Alarm .
Page 583 INDEX 581 Seat Belt Reminder ..... . .161 Maintenance Schedule ..... . .413 Security Alarm .
Page 584 582 INDEX Oil, Engine .......422 Parking Brake ......269 Capacity .
Page 585 INDEX 583 Preparation For Jacking ..... .392 Release, Hood ......115 Pretensioners Reminder, Seat Belt .
Page 586 584 INDEX Safety Checks Inside Vehicle ....255 Front Seat ..... . .204, 205, 207 Safety Checks Outside Vehicle .
Page 587 INDEX 585 Sentry Key Replacement ....25, 32 Remote ....... .28 Service Assistance .
Page 588 586 INDEX Tires ......257, 455, 462, 468 Tread Wear Indicators .....458 Aging (Life Of Tires) .
Page 589 INDEX 587 Fluid ....... . .487 Vanity Mirrors ......75 Maintenance .
Page 590 588 INDEX Fluid ....... . .420 Windshield Wiper Blades .....430 Windshield Wipers .
Page 591 INSTALLATION OF RADIO TRANSMITTING The antenna cable should be as short as practical and EQUIPMENT routed away from the vehicle wiring when possible. Use Special design considerations are incorporated into this only fully shielded coaxial cable. vehicle’s electronic system to provide immunity to radio Carefully match the antenna and cable to the radio to frequency signals.

Dodge Durango 2018 Owner's Manual

Table of Contents

Getting to Know Your Vehicle

Getting to Know Your Instrument Panel

Safety

Starting and Operating

In Case of Emergency

Quick Links

Chapters

Related Manuals for Dodge Durango 2018

Summary of Contents for Dodge Durango 2018