Table of Contents
Advertisement
Quick Links
KIT_XMC_PLT2GO_XMC4400 Evaluation Board guide
About this document
Scope and purpose
This document explains about the KIT_XMC_PLT2GO_XMC4400 Evaluation board: kit operation, out-of-the-box
example and its operation, and the hardware details of the board.
Intended audience
This document is intended for all embedded developers using the KIT_XMC_PLT2GO_XMC4400 Evaluation
board.
Evaluation board
This board is to be used during the design-in process for evaluating and measuring characteristic curves, and
for checking datasheet specifications.
Note:
PCB and auxiliary circuits are NOT optimized for final customer design.
User guide
Please read the sections "Important notice" and "Warnings" at the end of this document
Rev. 1.1
www.infineon.com
2025-01-23
Advertisement
Table of Contents
Related Manuals for Infineon XMC PLT2GO
Summary of Contents for Infineon XMC PLT2GO
-
Page 1: About This Document
This board is to be used during the design-in process for evaluating and measuring characteristic curves, and for checking datasheet specifications. Note: PCB and auxiliary circuits are NOT optimized for final customer design. User guide Please read the sections "Important notice" and "Warnings" at the end of this document Rev. 1.1 www.infineon.com 2025-01-23... -
Page 2: Important Notice
Boards provided by Infineon Technologies. The design of the Evaluation Boards and Reference Boards has been tested by Infineon Technologies only as described in this document. The design is not qualified in terms of safety requirements, manufacturing and operation over the entire operating temperature range or lifetime. -
Page 3: Safety Precautions
KIT_XMC_PLT2GO_XMC4400 Evaluation Board guide Safety precautions Safety precautions Note: Please note the following warnings regarding the hazards associated with development systems. Table 1 Safety precautions Warning: The DC link potential of this board is up to 1000 V or more. When measuring voltage waveforms by oscilloscope, high voltage differential probes must be used. -
Page 4: Table Of Contents
KIT_XMC_PLT2GO_XMC4400 Evaluation Board guide Table of contents Table of contents About this document ..............1 Important notice . -
Page 5: Introduction
-M4 based XMC Microcontroller from Infineon Technologies AG. ™ It can be used with a wide range of development tools including Infineon’s free of charge Eclipse based IDE ModusToolbox . The XMC4400 Platform2Go Series-V1.1 are designed to evaluate the capabilities of the ™... -
Page 6: Key Features
KIT_XMC_PLT2GO_XMC4400 Evaluation Board guide 1 Introduction The XMC4400 Platform2Go features an Ethernet-enabled communication option. You can control the XMC4400 Platform2Go via the web browser on your PC. Additional voltage level shifters and Arduino connection header on the XMC4400 Platform2Go allow the usage of Arduino shields with 3.3V or 5V logic level. - Page 7 KIT_XMC_PLT2GO_XMC4400 Evaluation Board guide 1 Introduction Table 3 (continued) Kit Features of Assembly Versions Feature XMC4400 XMC4400 XMC4400 XMC4400 Platform2Go 3.3V Platform2Go 3.3V Platform2Go Platform2Go Lite 5V Lite Voltage level shifter ✓ ✓ for 5 V Arduino Ethernet PHY and ✓...
-
Page 8: Block Diagram
Two 40-pin header X1 and X2 • Connection Header for Arduino • mikroBus connector ™ • Two Infineon Shield2Go connectors (at the bottom of the board) • Potentiometer (10kOhm) • On-board power generation • 2 User Push-Buttons, 2 User LEDs, Reset Push-Button •... -
Page 9: Hardware Description
KIT_XMC_PLT2GO_XMC4400 Evaluation Board guide 2 Hardware Description Hardware Description The following chapters give a detailed description of the board hardware and how it can be used. The different assembly versions of the kits series are shown in Figure Figure Figure 4 Figure Figure 2 XMC4400 Platform2Go 3.3V... - Page 10 KIT_XMC_PLT2GO_XMC4400 Evaluation Board guide 2 Hardware Description Figure 3 XMC4400 Platform2Go 5V Figure 4 XMC4400 Platform2Go 3.3V Lite User guide Rev. 1.1 2025-01-23...
- Page 11 KIT_XMC_PLT2GO_XMC4400 Evaluation Board guide 2 Hardware Description Figure 5 XMC4400 Platform2Go 5V Lite User guide Rev. 1.1 2025-01-23...
-
Page 12: Power Supply
KIT_XMC_PLT2GO_XMC4400 Evaluation Board guide 2 Hardware Description Power Supply The XMC4400 Platform2Go Series-V1.1 must be supplied by an external 5 Volt DC power supply connected to any of the micro USB plugs (X100, X101). The green Power LED (VDD3.3) indicates the presence of the generated 3.3 V supply voltage. -
Page 13: Pin Header X1 And X2
KIT_XMC_PLT2GO_XMC4400 Evaluation Board guide 2 Hardware Description Pin Header X1 and X2 The pin headers X1 and X2 can be used to extend the evaluation board or to perform measurements on the XMC4400. Figure 7 shows the available GPIOs/signals at these pin headers. The pin table is also printed onto the bottom side of the PCB in bottom view. -
Page 14: Pin Header For Microbus And Shield2Go Connector 1 And 2
KIT_XMC_PLT2GO_XMC4400 Evaluation Board guide 2 Hardware Description Pin Header for Microbus and Shield2Go Connector 1 and 2 The pin header for Microbus and Shield2Go Connector 1 and 2 can be used to extend the evaluation board or to perform measurements on the XMC4400. Figure 8 shows the available signals at these pin headers. -
Page 15: Solderable 0 Ohm Pin Bridges
KIT_XMC_PLT2GO_XMC4400 Evaluation Board guide 2 Hardware Description Solderable 0 Ohm Pin Bridges The 0 Ohm (0805) pin bridges enable/disable the signal pins in Table 4 (enabled by default). To disable the signals, their resistor has to be removed. The XMC4400 pins are then usable for other usages. Table 4 Signal mapping of the 0 Ohm Pin Bridges Resistor... -
Page 16: User Push Buttons And User Leds
KIT_XMC_PLT2GO_XMC4400 Evaluation Board guide 2 Hardware Description Figure 9 Mapping of Arduino Functions to XMC Pin Functions The XMC4400 Platform2Go 5V features bi-directional voltage level shifter and therefor supports 5 V Arduino shields. Jumper JP300 (IOREF) determines whether the Arduino shield is driven with 5 V or 3.3 V. Analog input signals ADC0-5 are limited to 3.3 V input voltage. -
Page 17: On-Board Debug Probe
KIT_XMC_PLT2GO_XMC4400 Evaluation Board guide 2 Hardware Description Table 6 (continued) XMC4400 Pin Mapping for User Push Buttons and Potentiometer Button XMC Pin Resistor BUTTON2 P3.2 Potentiometer P14.0 Each push Buttons, the potentiometer and the LEDs can be disabled by removing their resistor. Also see Table Debugging and UART-to-USB Communication... -
Page 18: Uart Communication For Xmc4200
KIT_XMC_PLT2GO_XMC4400 Evaluation Board guide 2 Hardware Description UART Communication for XMC4200 To enable* the optional UART communication between the XMC4400 and the XMC4200 Debugger, R1 and R2 have to be assembled with 0 Ohm, 0805 resistor. Table 7 XMC4400 Pins Mapping for Debugging and UART-Communication Pin Function Input/Output XMC Pin... -
Page 19: Can Transceiver
2.11 CAN Transceiver The XMC4400 Platform2Go provides a CAN interface via the X3 connector. Infineon’s high speed CAN transceiver IFX1051LE for industrial application supports 3.3V I/O logic and is suitable for 12V and 24V bus systems with an excellent EMC performance. The CAN bus (signals CANH, CANL) is not terminated by a 120Ohm and needs to be terminated externally. -
Page 20: Ethernet
KIT_XMC_PLT2GO_XMC4400 Evaluation Board guide 2 Hardware Description 2.13 Ethernet The XMC4400 Platform2Go provides an Ethernet Phy and RJ45 plug. Table 11 XMC4400 Pins used for Ethernet XMC Pin Ethernet Function XMC Function P15.9 Carrier Sense/Receive Data Valid ETH0.CRS_DVC P15.8 Clock Input ETH0.CLK_RMIIC P5.1 Interrupt (disabled... -
Page 21: Production Data
KIT_XMC_PLT2GO_XMC4400 Evaluation Board guide 3 Production Data Production Data This chapter covers schematics, board dimensions, component placement and the list of material. Schematics In the following figures shows the schematics of the XMC4400 Platform2Go Series-V1.1 in. User guide Rev. 1.1 2025-01-23... - Page 22 KIT_XMC_PLT2GO_XMC4400 Evaluation Board guide 3 Production Data C301 100nF C303 100nF C302 100nF C300 100nF Figure 10 Connectors Schematic: Pin header, Pin Bridges, Level Shifter, Microbus, Shield2Go Connector, Arduino Level Jumper, UART Bridges User guide Rev. 1.1 2025-01-23...
- Page 23 KIT_XMC_PLT2GO_XMC4400 Evaluation Board guide 3 Production Data C130 100nF C129 100nF C128 100nF C127 10uF C126 10uF 4.7uF C125 C124 100nF C123 100nF 5 TH-Pads 2.54mm pitch Figure 11 XMC_4200_Debug Schematic: OBD Probe, Ethernet, Quad-SPI Memory User guide Rev. 1.1 2025-01-23...
- Page 24 KIT_XMC_PLT2GO_XMC4400 Evaluation Board guide 3 Production Data Figure 12 XMC4400 Schematic: USB connector, Microcontroller pins and power, Potentiometer Buttons and LEDs User guide Rev. 1.1 2025-01-23...
- Page 25 KIT_XMC_PLT2GO_XMC4400 Evaluation Board guide 3 Production Data C133 10uF C132 10uF Figure 13 ICs and Power Schematic: Can Transceiver, RTC Battery, Power User guide Rev. 1.1 2025-01-23...
- Page 26 KIT_XMC_PLT2GO_XMC4400 Evaluation Board guide 3 Production Data Figure 14 Geometry User guide Rev. 1.1 2025-01-23...
-
Page 27: List Of Material
KIT_XMC_PLT2GO_XMC4400 Evaluation Board guide 3 Production Data List of Material The list of material is valid for the Platform2Go XMC4400 Lite/3.3V/5V. Table 13 List of Material Description Designator Package Value Quantity Not fitted in Reference Micro Miniature BUTTON1 P3.1, FSM2JSMA ... - Page 28 KIT_XMC_PLT2GO_XMC4400 Evaluation Board guide 3 Production Data Table 13 (continued) List of Material Description Designator Package Value Quantity Not fitted in Reference Chip Monolithic C125 0805/2012 4.7uF Ceramic Capacitor Chip Monolithic C400, C401 0402/1005 15pF Ceramic Capacitor Chip Monolithic C402 0603/1608 22uF...
- Page 29 KIT_XMC_PLT2GO_XMC4400 Evaluation Board guide 3 Production Data Table 13 (continued) List of Material Description Designator Package Value Quantity Not fitted in Reference Performance of IC101 IFX_ the ARM Cortex- XMC4200Q48K25 M4 Core with 6ABXUMA1 Powerful On-Chip Peripheral Subsystems, Temp Range(-40°C to 125°C)
- Page 30 KIT_XMC_PLT2GO_XMC4400 Evaluation Board guide 3 Production Data Table 13 (continued) List of Material Description Designator Package Value Quantity Not fitted in Reference For Power Lines; L400, L401 0603/1608 For General LED1 P0.6, LED2 P0.7 mikroBUS Host MIKROBUS ...
- Page 31 KIT_XMC_PLT2GO_XMC4400 Evaluation Board guide 3 Production Data Table 13 (continued) List of Material Description Designator Package Value Quantity Not fitted in Reference Standard Thick R109, R301, R303 0402/1005 Film Chip Resistor, 0R/50V Surface Mount R23 POTI P14, 15 Single Turn Trimmer, Model 23A - J Hook...
- Page 32 KIT_XMC_PLT2GO_XMC4400 Evaluation Board guide 3 Production Data Table 13 (continued) List of Material Description Designator Package Value Quantity Not fitted in Reference XMC4000 Family IFX_XMC4400- Microcontroller F100 for Industrial Applications, ® ® Cortex -M4, 32-bit processor core, Flash 512 Kbytes,SRAM 80 Kbytes (Temperature...
- Page 33 KIT_XMC_PLT2GO_XMC4400 Evaluation Board guide 3 Production Data Table 13 (continued) List of Material Description Designator Package Value Quantity Not fitted in Reference Through hole X300 Header 3X2A .025'' SQ Post Header, 2.54mm pitch, 6 pin, vertical, double Through hole X301 ...
-
Page 34: Revision History
KIT_XMC_PLT2GO_XMC4400 Evaluation Board guide Revision history Revision history Document Date Description of changes revision 2019-08-30 Initial version 2025-01-23 Template update. Replaced DAVE with ModusToolbox ™ ™ User guide Rev. 1.1 2025-01-23... -
Page 35: Disclaimer
Infineon Technologies, Email: erratum@infineon.com Infineon Technologies’ products may not be used in any applications where a failure of the product or any consequences of the use thereof can reasonably be Document reference expected to result in personal injury.
Need help?
Do you have a question about the XMC PLT2GO and is the answer not in the manual?
Questions and answers