Related Manuals for Denios STEELSAFE 1 FS
Summary of Contents for Denios STEELSAFE 1 FS
- Page 1 S T E E L S A F E H A Z A R D O U S M A T E R I A L D E P O T S O P E R A T I N G I N S T R U C T I O N S T R A N S L A T I O N O F T H E O R I G I N A L O P E R A T I N G I N S T R U C T I O N S V E R S I O N 2 0 2 4 - 0 9...
- Page 2 W W W . D E N I O S . C O M These instructions contain texts, images and drawings which need express written authorisation before they can be reproduced, distributed or otherwise shared, in part or in full. IMPORTANT Read carefully before commissioning © Copyright DENIOS SE Technical changes reserved!
-
Page 3: Table Of Contents
T A B L E O F C O N T E N T S . 1 . N O T I C E S R E G A R D I N G T H E O P E R A T I N G I N S T R U C T I O N S ..5 1 . - Page 4 5 . 2 S L I D I N G D O O R ..............2 1 5 .
- Page 5 1 . N O T I C E S R E G A R D I N G T H E O P E R A T I N G I N S T R U C T I O N S . Thank you for your trust in DENIOS! Before you put your product into operation, ensure you read these operating instructions completely.
-
Page 6: W A R N I N G S
Return to the table of contents 1 . 2 W A R N I N G S . Warnings are shown at the start of a chapter, or before sections in instructions for action where a hazard may occur. The warnings are structured as follows: NOTICE Warns of damage to property. -
Page 7: P I C T O G R A M S
Return to the table of contents 1 . 3 P I C T O G R A M S . Pictograms are used to warn of hazards: Pictogram Meaning General warning Warning: explosive substances Warning: risk of crushing Warning: risk of hand injury... -
Page 8: G E N E R A L S A F E T Y I N F O R M A T I O N
Return to the table of contents 2 . G E N E R A L S A F E T Y I N F O R M A T I O N . The product must only be used in accordance with the intended use. The product may only be used by persons who have been instructed and trained. -
Page 9: Explosion Hazard
Return to the table of contents 2 . 1 S A F E T Y I N F O R M A T I O N F O R U S E I N E X Z O N E S . DANGER Explosion hazard! The roller shutter models for the SteelSafe hazardous... -
Page 10: Further Information
Return to the table of contents 2 . 2 I N T E N D E D U S E . The SteelSafe hazardous materials depots consist of a non-combustible sheet steel construction with integral leak spill sump and individually removable grids. - Page 11 Return to the table of contents 2 . 2 . 1 P E R M I T T E D A N D P R O H I B I T E D S T O R A G E . The safety information in the safety data sheet for the stored substances must be observed! Notice for use in Ex zones:...
- Page 12 Return to the table of contents 2 . 2 . 2 M I S U S E . The following in particular is considered incorrect use: ■ Use of models with roller shutters in explosive atmospheres. ■ Use of model 1 l plus outdoors. ■...
- Page 13 Alongside the depot itself, the scope of delivery depends on the model ordered and its design. Your order confirmation contains all the information you need regarding additional parts. The accessories listed below can be reordered from DENIOS upon request. For model (+ item no.) Number Accessory (+ item no.)
- Page 14 Return to the table of contents 4 . I N S T A L L A T I O N . 4 . 1 I N S T A L L A T I O N C O N D I T I O N S . You will receive the hazardous materials depot in a packaged condition.
- Page 15 Return to the table of contents 4 . 2 ( O P T I O N A L ) R E M O V A L O F T H E T R A N S P O R T L O C K . CAUTION Risk of injury from crushing! Do not remove the transport lock until the hazardous...
- Page 16 Return to the table of contents 4 . 3 F I T T I N G O F E Q U I P O T E N T I A L B O N D I N G . Notice for use in Ex zones: Before commissioning, the equipotential bonding must be connected with the ground.
- Page 17 Return to the table of contents 4 . 4 ( O P T I O N A L ) S E T T I N G U P T H E S T E E L S H E L V I N G . Some variants of SteelSafe depots come with steel shelving which must be p .
-
Page 18: Before Continuing
Return to the table of contents Press the side bar flat against the T-profile Tap down the side bar into the T-profile using a rubber mallet. Press in the clips on the side bar using a screwdriver or a punch. Before continuing: Place the T-profile frame as shown. -
Page 19: S A F E T Y I N F O R M A T I O N F O R U S E I N E X Z O N E S
Return to the table of contents Position the side frames on the left and right of the spill sump on the depot. Fit the upper and lower cross bars Secure the cross bars with the safety pins Fit the centre cross bar at the desired height. Set the shelves between the front and rear cross bars. -
Page 20: O P E N I N G A N D C L O S I N G T H E D E P O
Return to the table of contents 5 . O P E N I N G A N D C L O S I N G T H E D E P O T . The three door designs: Wing door Sliding door Roller shutter (Product may vary from the illustration) - Page 21 Return to the table of contents 5 . 1 W I N G D O O R . Insert the key into the lock and turn it. Turn the handle on the door, then raise it. To close the depot, carry out the above steps in reverse order.
-
Page 22: T E C H N I C A L D A T
Return to the table of contents 6 . T E C H N I C A L D A T A . The SteelSafe hazardous material depots are available in different sizes, designs, and with or without one or multiple shelves. When using your depot, be sure not to exceed the maximum load limits! You can see the model name of your SteelSafe hazardous material depot on the nameplate. -
Page 23: M O D E L S 1 I , 1 I P L U S A N
Return to the table of contents 6 . 2 M O D E L S 1 I , 1 I P L U S A N D 2 I . Model 1 I plus Item number 280 244 312 191 281 129 External dimensions 1420 x 1635 x 2020... - Page 24 Return to the table of contents 6 . 4 M O D E L S 2 D , 4 D A N D 4 4 4 0 D W I T H R O L L E R S H U T T E R S . Model 4 440 D Item number...
- Page 25 Return to the table of contents 7 . 2 D I S P O S A L . The SteelSafe hazardous materials depot is mainly constructed from metal parts. Dispose of any waste materials in accordance with regional statutory regulations after taking the sump out of service. The spill sump must be cleaned of all residues before disposal.
- Page 26 Return to the table of contents 8 . I N S E R T . 8 . 1 M A N U F A C T U R E R ' S D E C L A R A T I O N . Manufacturer's declaration Ignition hazard assessment / non-electrical equipment in accordance with DIN EN ISO 80079-36:2016-12,...
- Page 27 8 . 2 D E C L A R A T I O N O F C O M P L I A N C E . This declaration of compliance is a translation of the original! Declaration of compliance (ÜHP) We at DENIOS SE, hereby confirm that the product meets the requirements for steel spill sumps with up to 1000 litre volume (StawaR directive). Models...
Need help?
Do you have a question about the STEELSAFE 1 FS and is the answer not in the manual?
Questions and answers