Related Manuals for Total INDUSTRIAL TOPLI2001 Series
Summary of Contents for Total INDUSTRIAL TOPLI2001 Series
- Page 1 PRODUCT MANUAL CORDLESS POLISHER TOPLI2001xy UTOPLI2001xy x(blank, 1,2,3,4,5,6,7,8,9, E, S,A,M) y(blank, -1,-2,-3,-4,-5,-6,-7,-8,-9, E, S,A,M)
-
Page 2: General Safety Warnings
| English Original Instructions GENERAL SAFETY WARNINGS ⚠ Warning! Work area safety Keep work area clean and well lit. Cluttered and dark areas invite accidents. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes. - Page 3 | English Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries. Prevent unintentional starting. Ensure the switch is in the off position before connecting to power source and/or battery pack, picking up or carrying the tool.
- Page 4 | English operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. Use the power tool, accessories, and tool bits etc.
- Page 5 | English BATTERY TOOL SAFETY WARNINGS Save these instructions. Caution: only use genuine original batteries. Use of non-genuine batteries, or batteries that have been altered, may result in the battery bursting causing fires, personal injury, and damage. It will also void the warranty for the tool and charged and dark areas invite accidents.
- Page 6 | English Never recharge a fully charged battery cartridge. Overcharging shortens the battery service life. Charge the battery cartridge with room temperature at 10°C-40°C (50°F- 104°F). Let a hot battery cartridge cool down before charging it. Charge the battery cartridge if you do not use it for a long period (more than six months).
- Page 7 | English THE SYMBOLS IN INSTRUCTION MANUAL Read the instruction manual before using CE conformity. Safety alert. Please only use the accessories supported by the manufacturer. Wear safety glasses, hearing protection and dust mask. Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist.
-
Page 8: Additional Safety Warning
Additional notes The declared total vibration value has been measured using the standard test method and can be used to compare one tool to another. The declared total vibration value can be used in the initial exposure assessment. Warning! The vibration emission during tool operation may diff er from the declared value, depending on the way the tool is used. -
Page 9: Technical Specifications
| English Technical specifications TOPLI2001xy UTOPLI2001xy x (blank, 1,2,3,4,5,6,7,8,9, x (blank, 1,2,3,4,5,6,7,8,9, Model No. E, S,A,M) E, S,A,M) y (blank, -1,-2,-3,-4,-5,-6,-7,- y (blank, -1,-2,-3,-4,-5,-6,-7,- 8,-9, E, S,A,M） 8,-9, E, S,A,M） Voltage 2500/min No-load Speed 254mm 10˝ Max. mixing paddle dia. IPX0 Mixing pad thread... - Page 10 | English ⚠ Warning! Only use original battery pack and battery charger as below for this power tool: x (blank, 1, 2, 3, 4, 5, 6, 7, 8, 9, E, S, A, M) y (blank, -1, -2, -3, -4, -5, -6, -7, -8, -9, E, S, A, M) Product Battery pack TFBLI2001...
-
Page 11: Operation
| English OPERATION PICTURE OPERATION Make sure the battery has been disconnected from the tool. Check the polishing disc for damage. If any cracks, scratches or other damage are visible, replace the disc with a new one free of these defects. It is forbidden to work with damaged discs! Install the additional handle and the polishing disc. - Page 12 | English tool with smooth movements to and from you. Observe the effects of work and adjust the pressure of the polishing disc. Avoid working in one place for too long, it may lead to local overheating of the polished material and lead to uneven work results.
- Page 13 | English MAINTENANCE&MALFUNCTIONS Possible malfunctions and methods of their eliminations Malfunction Probable causes Actions ● Switch failure ●The power cord or wiring is broken, Disconnect When the machine is turned power cord plug malfunction; machine from the on, the electric motor does ●...
- Page 14 TOTAL TOOLS WORLD T0424.V03 MADE IN CHINA NEWWAY TECHNOLOGY (SUZHOU) CO., LIMITED...
Need help?
Do you have a question about the INDUSTRIAL TOPLI2001 Series and is the answer not in the manual?
Questions and answers