GEZE ECdrive T2 Series Pre-Installation Instructions
GEZE ECdrive T2 Series Pre-Installation Instructions

GEZE ECdrive T2 Series Pre-Installation Instructions

Hide thumbs Also See for ECdrive T2 Series:

Advertisement

Quick Links

ECdrive T2
EN Pre-installation instructions
Product family
186936-01

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ECdrive T2 Series and is the answer not in the manual?

Questions and answers

Summary of Contents for GEZE ECdrive T2 Series

  • Page 1 ECdrive T2 EN Pre-installation instructions Product family 186936-01...
  • Page 2: Table Of Contents

    ECdrive T2 Product family Contents Introduction................................3 Symbols and illustrations....................................3 Revisions and validity......................................3 Product liability .........................................3 Reference documents .....................................3 Fundamental safety precautions ........................4 Intended use........................................4 Safety instructions ......................................4 Safety-conscious working .....................................5 Environmentally conscious working .................................5 Safety instructions related to transportation and storage .......................5 Qualification ........................................5 About this document .............................6 Overview..................................6...
  • Page 3: Introduction

    ECdrive T2 Product family Introduction Introduction 1. 1 Symbols and illustrations Warning notices In these instructions, warning notices are used to warn against material damage and injuries. Always read and observe these warning notices. Observe all measures marked with the warning symbol and warning word. Warning Warning Meaning...
  • Page 4: Fundamental Safety Precautions

    à in the installation variants / types of installation documented by GEZE à within the tested/approved area of application (climate / temperature / IP rating) Any other use is considered non-intended and will lead to the exclusion of all liability and warranty claims to GEZE. Safety instructions à...
  • Page 5: Safety-Conscious Working

    ECdrive T2 Product family Fundamental safety precautions Safety-conscious working à Secure workplace against unauthorised entry. à Use only the cables specified on the cable plan provided. Cables must be shielded in compliance with the wir- ing diagram. à Secure loose, internal drive cables with cable ties. à...
  • Page 6: About This Document

    About this document ECdrive T2 Product family About this document These instructions describe the pre-mounting of the ECdrive T2 product family automatic sliding door drive. Overview 4. 1 Diagrams Drawing no. Type Name 70518-0-001 Drive drawing ECdrive T2, drives 70518-2-0200 Machining drawing Track 70518-2-0205...
  • Page 7: Tools And Aids

    ECdrive T2 Product family Overview Tools and aids Tool Closer size Tape measure Marking pen Torque spanner Allen key 2 mm, 2.5 mm, 3 mm, 4 mm, 5 mm, 6 mm Open-ended spanner 8 mm, 10 mm, 13 mm Screwdriver set Phillip's head PH2 and PH4 Torx key Tx 20;...
  • Page 8: Components And Assembly Groups

    Overview ECdrive T2 Product family Components and assembly groups These illustrations show the equipment of a standard drive in 2-leaf and 1-leaf version. The structure of the assembly groups can vary depending on the drive equipment or version. Precise details about positioning of the individual components can be found on the drive diagram.
  • Page 9: Pre-Mounting

    ECdrive T2 Product family Pre-mounting Pre-mounting The up-to-date drive diagram is applicable for the pre-mounting work to be carried out. All components must be identified and installed in accordance with the drive diagram. 5. 1 Machining the track and cover Check profiles for damage.
  • Page 10: Connecting The Contact On The Toothed Belt Locking (Optional)

    Pre-mounting ECdrive T2 Product family Connecting the contact on the toothed belt locking (optional) Remove the screws (4) on the feedback switch (2) of the tooth belt locking mechanism. Place the alarm contact switch (3) on the feed- back switch (2). Fasten both switches on the tooth-belt locking mechanism with the longer screw (4) from the retrofit set.
  • Page 11: Fitting The Right-Hand Module Mount

    ECdrive T2 Product family Pre-mounting Fitting the right-hand module mount Install the right-hand module mount as shown in the drawing. Drawing no. Name 70518-1-0110 Right module mount 70518-1-0111 Right module mount only 1-leaf right hand slide to open with locking mechanism 70518-1-0112 Right module mount FR 70518-1-0113...
  • Page 12: Installing Cable Guides

    Pre-mounting ECdrive T2 Product family Installing cable guides Cables can be cut! Lay cables in such a way that there are no cables near the moving parts. Fix the cable guide (2) on the module mount (1) and track (3). Distance to cable guide approx. 200 mm. Connecting motor gear unit and control unit ECdrive T2 Lay the rotary encoder cable (2) and motor con-...
  • Page 13: Pre-Positioning The Pre-Mounted Module Mount, Left And Right

    ECdrive T2 Product family Pre-mounting ECdrive T2-FR Route the rotary transducer cable (2), motor connection cable (3) and motor connection cable of the second motor (1) to control unit. Insert the connector into the control unit (4). Do not plug rechargeable battery cable into the control unit yet. The rechargeable battery is not connected to the control unit until the production test and commissioning.
  • Page 14: 5. 1 0 Connecting Transformer And Control Unit

    Pre-mounting ECdrive T2 Product family 5. 1 0 Connecting transformer and control unit Make sure that cables are routed and secured in such a way that they do not become jammed when the cover is slid in place and cannot come into contact with moving components. Cut the three-strand transformer cable (1) to length.
  • Page 15: 5. 1 1 Connecting The Toothed Belt Locking (Optional) And Control Unit

    ECdrive T2 Product family Pre-mounting Fit the three-core transformer cable (1) to termi- nal (5) of the transformer. 5. 1 1 Connecting the toothed belt locking (optional) and control unit Plug the cable for tooth belt locking mecha- nism (1) in at the control unit (2). Lay the cable for tooth belt locking mecha- nism (1) through the cable guide to the tooth belt locking mechanism (optional) (3), shorten...
  • Page 16: 5. 1 2 Attaching The Track Ground Connection

    Pre-mounting ECdrive T2 Product family 5. 1 2 Attaching the track ground connection Precise details about positioning of the individual components can be found on the drive diagram. 2-leaf Drives Regardless of the drive length, always install 2 grounding points beside the left module mount (see image) and on the end of the track (see drive diagram): Screw the device flat plug (1) to the end of the track using the enclosed screw (2) and toothed lock washer (3) (torque 3.5 Nm).
  • Page 17: 5. 1 3 Connecting Rechargeable Battery And Control

    ECdrive T2 Product family Pre-mounting 1-leaf drives Long drives In longer drives, an additional grounding point is required beside the module mount (7) (see drive diagram). Install the device flat plug (1) aligned horizontally (3.5 Nm). Connect the extension line (5) to the transformer cable (4). Connect the extension line with the device flat plug (1).
  • Page 18: Device Safety Test And Production Test

    Device safety test and production test ECdrive T2 Product family Device safety test and production test WARNING! Risk of fatal injury due to electric shock! The electrical system (230 V/115 V) may only be Action connected and disconnected by a professional electri- cian or specialist electrician.
  • Page 19: Preparation For Installation

    The position of the hole must be checked on site. Depending on the positioning of the drive components, minor deviations can occur here. GEZE thus recommends only drilling the hole on site once the exact position of the locking mechanism is known. Dimensional specifications for dimension C can be found in the machining drawing for the cover.
  • Page 20: Fitting The Cover Earthing

    Preparation for installation ECdrive T2 Product family Secure the cover suspension piece (1) on the right and left with approx. 50 mm dis- tance to the end of the cover with 2 screws (max. torque 1.5 Nm). Hook the cover safety rope (3) on the cover suspension piece (1).
  • Page 21: Installing The Side Plates

    ECdrive T2 Product family Preparation for installation Installing the side plates Push the sealing brush in before installation in tracks for post-rail assembly. Screw the sheet-metal part (3) for securing the cover in the left-hand and right-hand side panels (2) (torque max. 1.5 Nm). Screw the side panels (2) to the track (1) (torque 5 Nm).
  • Page 22 ECdrive T2 Product family...
  • Page 23 ECdrive T2 Product family...
  • Page 24 E-Mail: leonberg.de@geze.com Baltic States – Iberia Scandinavia – Norway Lithuania / Latvia / Estonia GEZE Iberia S.R.L. GEZE Scandinavia AB avd. Norge GEZE GmbH E-Mail: norge.se@geze.com E-Mail: baltic-states@geze.com E-Mail: info.es@geze.com Niederlassung Süd-Ost www.geze.no www.geze.es Tel. +49 (0) 7152 203 6440 E-Mail: muenchen.de@geze.com...

Table of Contents