Advertisement
Quick Links
Essex crib and changer
Important Information:
Read all instructions BEFORE assembling crib.
KEEP INSTRUCTIONS FOR FUTURE USE.
IMPORTED BY C&T International, Inc. / IMPORTE` PAR de C&T International, Inc.
105 Stonehurst Ct Northvale, NJ 07647 U.S.A.
CANADA ADDRESS:
3453, DU PRESIDENT KENNEDY LAC MEGANTIC, QUEBEC, CANADA G6B 2Y4
Website: www.sorellefurniture.com / Site Internet : www.sorellefurniture.com
Assembly Instruction
Tel, 201- 531-1919 Fax, 201- 531-1920
CN240802 REV 1.0
Advertisement
Related Manuals for Sorelle Essex
Summary of Contents for Sorelle Essex
- Page 1 Tel, 201- 531-1919 Fax, 201- 531-1920 CANADA ADDRESS: 3453, DU PRESIDENT KENNEDY LAC MEGANTIC, QUEBEC, CANADA G6B 2Y4 Website: www.sorellefurniture.com / Site Internet : www.sorellefurniture.com Essex crib and changer Assembly Instruction Important Information: Read all instructions BEFORE assembling crib. KEEP INSTRUCTIONS FOR FUTURE USE.
- Page 2 Securely tighten loose bolts and other fasteners. Do not use crib if any parts are missing, damaged or broken.Contact C&T International Inc./Sorelle for replacement parts and instructional literature if needed. Do not substitute parts. *Follow warnings on all products in a crib.
- Page 3 Do not leave a child unattended in or on this accessory. Child must be no more than 30 lbs. to use this changing table. Use only the pad provided by C&T International / Sorelle or Manufacturer’s TODDLER BED WARNINGS WARNING INFANTS HAVE DIED IN TODDLER BEDS FROM ENTRAPMENT.
-
Page 4: Parts Identification
ESSEX CRIB AND CHANGER ASSEMBLY INSTRUCTIONS NOTES ON ASSEMBLY: -During the assembly process whenever using screws or bolts, check each by placing the screw/bolt on the diagram of the item which is drawn actual size and design. Be sure to use the proper size and shape specified in the instructions. -
Page 5: Hardware Identification
ESSEX CRIB AND CHANGER ASSEMBLY INSTRUCTIONS HARDWARE IDENTIFICATION Spec. REF. Name Allen Bolt 13*M6*75mm Ø 13*M6*60mm Ø Allen Bolt Allen Bolt 13*M6*55mm Ø Allen Bolt 13*M6*45mm Ø Allen Bolt 13*M6*40mm Ø Allen Bolt 13*M6*30mm Ø Allen Bolt 13*M6*17mm Ø 10*M6*17mm Slotted Nut Ø... - Page 6 ESSEX CRIB AND CHANGER ASSEMBLY INSTRUCTIONS STEP 1 STEP 2...
- Page 7 ESSEX CRIB AND CHANGER ASSEMBLY INSTRUCTIONS STEP 3 STEP 4...
- Page 8 ESSEX CRIB AND CHANGER ASSEMBLY INSTRUCTIONS STEP 5 STEP 6 Insert three (3) drawers into changer.
- Page 9 ESSEX CRIB AND CHANGER ASSEMBLY INSTRUCTIONS STEP 7 STEP 8...
- Page 10 ESSEX CRIB AND CHANGER ASSEMBLY INSTRUCTIONS STEP 9 STEP 10 Recommended mattress position: Top position for newborn. Middle position as your child starts to roll over. Lowest position when your child can sit or pull up on his/her knees.
- Page 11 ESSEX CRIB AND CHANGER ASSEMBLY INSTRUCTIONS STEP 11 STEP 12 FINALLY CHECK • PRIOR TO USING THE CRIB, ENSURE ALL BOLTS ARE TIGHTENED. DO NOT OVER TIGHTEN. • ENSURE THAT THE MATTRESS IS THE RECOMMENDED SIZE. • ENSURE THE MATTRESS BASE IS LOCATED AT THE CORRECT LEVEL TO SUIT THE CHILD.
- Page 12 ESSEX CRIB AND CHANGER ASSEMBLY INSTRUCTIONS STEP 13 Important : If changing pad and safety belt are assembled, make sure warnings are facing up and visible. If not, reassemble by following the steps below. 1. Locate safety belt bolted to dresser top. Insert safety belt through slit in changing pad from back of pad.
- Page 13 ESSEX CRIB AND CHANGER ASSEMBLY INSTRUCTIONS Converting to a Toddler Bed (Optional) Follow all instructions supplied with the 148# Toddler Rail System. NOTE:148# Toddler Rail System is not included. Please see your crib retailer, visit WWW.Sorellefurniture.com or contact C&T International / Sorelle for more information.
- Page 14 ESSEX CRIB AND CHANGER ASSEMBLY INSTRUCTIONS NOTES BE A A THI Disassembling Crib for Storage To disassemble crib for storage, follow assembly steps in reverse. Store all parts and hardware together in a safe place. Store the instruction manual in the supplied envelope attached to mattress support base for future reference for reassembly.
Need help?
Do you have a question about the Essex and is the answer not in the manual?
Questions and answers