HIKVISION DS-KV8103Y-IMPE2 Manual

DS-KV8103Y-IMPE2
Video Intercom Two-Wire Villa Door Station
UD33350B
Diagram References
Appearance
1 Microphone 2 Calling Indicator 3 Speaking Indicator
4 Open Door Indicator 5 Built-in Camera 6 Supplement Light
7 Loudspeaker 8 TAMPER 9 Call Button
Terminals
1
AIN2 : Alarm Input 2
A1 NC1 : Normally Close A7
A2 AIN1 : Alarm Input 1
NO1 : Normally Open A8
A3
COM : Common Interface 12V OUT : Power Output for Lock
A9
A4 NC2 : Normally Close
A10 GND : Grounding
A5 NO2 : Normally Open
A11 2-WIRE: Wire to Indoor Station
A6 GND : Grounding
Installation
2
The door station supports surface mounting and flush mounting.
You are required to use the protective shield for surface mounting.
You are required to use the mounting box for flush mounting.
The dimension of the protective shield and mounting box is showed in part 2.1.
Before you begin:
1. Make sure the device in the package is in good condition and all the assembly
parts are included.
2. Make sure all the related equipment is power-off during the installation.
3. Check the product specification for the installation environment.
4. Connect cables to the door station before mounting.
Surface Mounting with Protective Shield
1. Secure the protective shield to the wall with 4 screws (KA-4X22-SUS) .
2. Use the wrench to secure the door station to the protective shield with 4 screws
(KM3X37) .
Flush Mounting with Mounting Box
1. Cave the installation hole, and pull the cable out.
2. Insert the mounting box into the hole with 4 screws.
3. Install the door station into the mounting box, and fix it with 4 screws.
Getting Started
3
Wire the door station to the indoor station with 2-wire cables.
You can activate the door station by indoor station.
Set the open duration and other parameters by indoor station.
Refers to the Indoor Station User Manual for details.
The application of the device is shown.
Video Intercom Operation
4
You can call the resident by pressing the call button.
1. Press the call button of the door station.
2. The resident can receive/decline the video call, unlock the door, etc.
Note:
When the video intercom between you and the resident is realized, you can speak to the
resident, and the live view of door station will be displayed on the connected indoor
station.
When the door station is calling the resident, the door station will detect the brightness
of video automatically. When the brightness is lower than the expected threshold, the
supplement light will be enabled.
When the supplement light is enabled, the backlight of key will be auto-enabled,
otherwise, the door station will detect the brightness of live view and enable the backlight
of key when the brightness of live view is lower than expected threshold.
5
Installation Positions
Recommended Installation Height (The distance between the camera and the ground):
1.4 m to 1.6 m
The FOV of the camera is : Horizontal: 140°, Vertical: 85°.
The highest visual height and lowest visual height of the camera is shown in the picture.
Refers to Video Intercom Villa Door Station User
Manual (scan the QR code) for details.
Quick Start Flow Chart
1 Terminals
Terminals and terminal
description.
2 Installation
2.1 Mounting accessories.
2.2 Installation of the
device: Surface mounting
and flush mounting.
3 Getting Started
What you should do to
get started.
4 Operation
Quick Operation of the
device.
5 Installation Position
5.1 Recommended
installation height .
5.2 FOV and visual height
of the camera .
.
Appearance
1
2
3
4
1
A1
NC1 NO1 COM NC2 NO2 GND
LOCK1 LOCK2
2.1
Protective Shield
115 mm
59.5 mm
5
6
7
8
9
A11
AIN2 AIN1 12V GND 2-WIRE
OUT
ALARM IN
LOCK POWER
Mounting Box
105 mm
39 mm