Download Print this page

Vision ZM1601US-8 Installation & Operation Manual

Wireless siren & strobe alarm battery power

Advertisement

Quick Links

Federal Communications Commission Statement
This equipment has been followed to comply with Part 15 of the FCC Rules. This
equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try and correct the
interference by one of the following measures:
-Reorient or relocate the receiving antenna,
-Increase the separation between the equipment and receiver,
-Connect the equipment into and outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesirable operation.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this equipment.
Limited Warranty
Vision Guarantees that every wireless siren & strobe alarm is free from physical
defects in material and workmanship under normal use for one year from the
date of purchase. If the product proves defective during this one-year warranty
period, Vision will replace it free of charge. Vision does not issue any refunds.
This warranty is extended to the original end user purchase only and is not
transferable. This warranty does not apply to : (1) damage to units caused by
accident, dropping or abuse in handling, or any negligent use; (2) units which
have been subject to unauthorized repair, taken apart, or otherwise modified;
(3) units not used in accordance with instruction; (4) damages exceeding the
cost of the product; (5) transit damage, initial installation costs, removal cost, or
reinstallation cost.
For information on addional devices, plesae visit us at www.visionsecurity.com.tw
ZM1601-8
V0
1130423
The Ultimate in Security & Automation
Installation & Operation Manual
ZM1601US-8
ZM1601USLR-8
ZM1601EU-8
ZM1601BR-8
ZM1601IN-8
ZM1601IL-8
ZM1601RU-8
ZM1601JP-8
ZM1601KR-8
Wireless Siren & Strobe Alarm
Battery Power
www.visionsecurity.com.tw

Advertisement

loading
Need help?

Need help?

Do you have a question about the ZM1601US-8 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Vision ZM1601US-8

  • Page 1 ZM1601IL-8 date of purchase. If the product proves defective during this one-year warranty period, Vision will replace it free of charge. Vision does not issue any refunds. ZM1601RU-8 This warranty is extended to the original end user purchase only and is not ZM1601JP-8 transferable.
  • Page 2 Z-Wave™ Command Classes: Introduction Thanks for choosing the Vision’s wireless siren & strobe alarm of the home security REQUIRED device. This siren is a Z-Wave™ enabled device (interoperable, two-way RF mesh COMMAND CLASS NAME VERSION SECURITY networking technology) and is fully compatible with any Z-Wave™ enabled network CLASS and its security framework.
  • Page 3 Configuration – Siren Single Count Installation Size VALUE Default Parameter 2 0 (off)、1 ~ 10 0 (off) (Parameter 2) To set up the alarm time when triggered. Parameter 3 will activate when Parameter 2 is 0 (off) Note: If you are installing the entire Z-Wave™ system for the first time, please refer to the installation guide of Z-Wave™...
  • Page 4 Support OTA Firmware update from controller. Please refer to your controller Operation manual. Once OTA function succeeded, we recommend you to proceed the factory Normal operation, the LED will light off. default reset (please refer to 6. & include again.) (Remark: Please replace a new battery for OTA process since it will consume the battery power a lot under few minutes!) Alarm Mode:...

This manual is also suitable for:

Zm1601uslr-8Zm1601eu-8Zm1601br-8Zm1601in-8Zm1601il-8Zm1601ru-8 ... Show all