Advertisement
Federal Communications Commission Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try and correct the interferene by one of the following measures:
- Reorient or relocate the receiving antenna,
- Increase the separation between the equipment and receiver,
- Connect the equipment into and outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undersired
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this equipment.
Limited Warranty
Vision Guarantees that every wireless siren & strobe alarm is free from physical defects
in material and workmanship under normal usage for one year from the date of purchase.
If the product proves defective during this one-year warranty period, Vision will replace it
free of charge. Vision does not issue any refunds. This warranty is extended to the
original end user purchase only and is not transferable. This warranty does not apply to :
(1) damage to units caused by accident, dropping or abuse in handling, or any negligent
usage; (2) units which have been repaired, taken apart, or modified by a unauthorized
personnel; (3) units not used in accordance with instruction; (4) damages exceeding the
cost of the product; (5) transit damage, initial installation costs, removal cost, or
reinstallation cost.
For information on addional devices, plesae visit us at www.visionsecurity.com.tw
ZM1602-5
V1
1040909
6B1Z-16006
Installation & Operation Manual
ZM 1602 IN-5
ZM 1602 MY-5
ZM 1602 EU-5
ZM 1602 RU-5
ZM 1602 US-5
ZM 1602 IL-5
ZM 1602 KR-5
ZM 1602 HK-5
ZM 1602 JP-5
ZM 1602 BR-5
DC/AC Power Siren
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Vision ZM 1602 IN-5
Summary of Contents for Vision ZM 1602 IN-5
- Page 1 If the product proves defective during this one-year warranty period, Vision will replace it ZM 1602 MY-5 free of charge. Vision does not issue any refunds. This warranty is extended to the ZM 1602 EU-5 original end user purchase only and is not transferable. This warranty does not apply to :...
- Page 2 Z-Wave Command Class: Introduction COMMAND_CLASS_ASSOCIATION_V2 Thanks for choosing the Vision’s wireless siren & strobe alarm of the home security device. COMMAND_CLASS_ASSOCIATION_GRP_INFO COMMAND_CLASS_CONFIGURATION This sensor is a Z-Wave™ enabled device (interoperable, two-way RF mesh networking technology) and is fully compatible with any Z-Wave™ enabled network and it’s security...
- Page 3 Z-Wave NIF and not be included then it will send 4 times NWI in every 4 ~ 6 Operation seconds for auto inclusion. The LED Setting Light will flash again if the siren has not Normal operation, the LED light will not on. been included or the LED Setting Light will go off after inclusion.) Alarm Mode: For “Exclusion”...
Need help?
Do you have a question about the ZM 1602 IN-5 and is the answer not in the manual?
Questions and answers