Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Offroad Animal Manuals
  4. Automobile Accessories
  5. FB-IGR-G1-23-PR-ASM0
  6. Fitting instruction

Offroad Animal FB-IGR-G1-23-PR-ASM0 Fitting Instruction

Ineos grenadier 23+ predator & toro front bar
Hide thumbs

Advertisement

Quick Links

Download this manual
IMPORTANT! – READ BEFORE INSTALLATION
•
When installed in accordance with these instructions, the front protection bar does
not affect the operation of the vehicles SRS airbags.
•
This product must be installed exactly as per these instructions using only
hardware supplied.
•
Take a few moments to read instructions thoroughly before beginning work.
•
In the event of damage to any bar component please contact OFFROAD ANIMAL
to arrange repair/replacement of components.
•
Do not use this product for any vehicle make or model other than that specified on
these instructions.
•
Do not remove labels from this product.
•
This product and its fixings must not be modified in any way unless stated in these
fitting instructions.
•
The installation of this product is recommended for trained personnel.
•
These instructions are correct at time of publication. OFFROAD ANIMAL cannot
be held responsible for the impact of any changes subsequently made by the
vehicle manufacturer. If you find something has changed please contact us to let
us know!
•
During installation it is the duty of the installer to check correct
operation/clearances of all components.
•
If Instructions are to be printed for reference in the workshop, it is recommended
that they are printed in colour, for best legibility.
•
All Grenadiers have a complex electrical system with the main battery under the
rear seat. If vehicle is not equipped with "High Load Auxiliary Switch Panel &
Electrical Preparation" engage a qualified auto electrician to connect the winch.
REV A
FB-IGR-G1-23-PR-ASM0
Fitting Instruction
07/11/2024
INEOS Grenadier 23+
Predator & Toro Front Bar
Page 1 of 65

Advertisement

loading
Need help?

Need help?

Do you have a question about the FB-IGR-G1-23-PR-ASM0 and is the answer not in the manual?

Questions and answers

Related Manuals for Offroad Animal FB-IGR-G1-23-PR-ASM0

Summary of Contents for Offroad Animal FB-IGR-G1-23-PR-ASM0

  • Page 1 • Take a few moments to read instructions thoroughly before beginning work. • In the event of damage to any bar component please contact OFFROAD ANIMAL to arrange repair/replacement of components. • Do not use this product for any vehicle make or model other than that specified on these instructions.
  • Page 2 FB-IGR-G1-23-PR-ASM0 INEOS Grenadier 23+ Fitting Instruction Predator & Toro Front Bar IMPORTANT: Check all parts are present before beginning work! Contact OFFROAD ANIMAL if something is missing. Main Parts – In the Box Part Number Description Image Ineos Grenadier FB-IGR-G1-...
  • Page 3 FB-IGR-G1-23-PR-ASM0 INEOS Grenadier 23+ Fitting Instruction Predator & Toro Front Bar Ineos Grenadier Under B-1342L Panel Support Bracket Ineos Grenadier Under B-1342R Panel Support Bracket Ineos Grenadier Wheel B-1341 Arch Liner Bracket Ineos Grenadier Under B-1343L panel Center Brace Ineos Grenadier Under...
  • Page 4 FB-IGR-G1-23-PR-ASM0 INEOS Grenadier 23+ Fitting Instruction Predator & Toro Front Bar FB-IGR-G1- ADR Compliance Plate 23-PR- Ineos Grenadier ARDCP Optional Winch Cover Kit - FB-IGR-G1-23-PR-ASM4 Part Description Image Number Ineos Grenadier Front Bar Winch B-1297 Delete Panel Ineos Grenadier Front Bar Winch...
  • Page 5 FB-IGR-G1-23-PR-ASM0 INEOS Grenadier 23+ Fitting Instruction Predator & Toro Front Bar Predator Small Parts – Contained in Small Parts Kit Bag QTY. PART NO. DESCRIPTION M8 X 20 BHCS BLACK SCREW, BUTTON HEAD CAP, ZINC M8X20X1.25, ISO4042 ZnNi BLACK PASSIVATED FINISH M8 FLAT WASHER- M8 FLAT WASHER, 16.5x8.4x1.2,...
  • Page 6 FB-IGR-G1-23-PR-ASM0 INEOS Grenadier 23+ Fitting Instruction Predator & Toro Front Bar The following tools will be required to install the product. Hand Tools Power Tools Workshop Supplies Metric Socket Set 8- Electric/Air Impact Panel Stand or Soft 19mm Driver (Optional)
  • Page 7 FB-IGR-G1-23-PR-ASM0 INEOS Grenadier 23+ Fitting Instruction Predator & Toro Front Bar It is the responsibility of the installer to always complete works in a safe manner. Make sure the following safety equipment is available and precautions are observed whilst fitting this product.

  • Page 8: Tools Required

    FB-IGR-G1-23-PR-ASM0 INEOS Grenadier 23+ Fitting Instruction Predator & Toro Front Bar Top - 2x Torx Remove from bottom Bottom - 2x Torx once bolts released 1. Park up vehicle in appropriate work location TOOLS REQUIRED and remove the front number plate.
  • Page 9 FB-IGR-G1-23-PR-ASM0 INEOS Grenadier 23+ Fitting Instruction Predator & Toro Front Bar RH SIDE SHOWN 2x Torx - Top 2x Torx - Bottom 4. Remove the 2x Torx head screws on the top of the TOOLS REQUIRED bumper, under the cover 8mm socket 5.
  • Page 10 FB-IGR-G1-23-PR-ASM0 INEOS Grenadier 23+ Fitting Instruction Predator & Toro Front Bar Release wiring clips with trim tool Disconnect Electrical Connector 8. With all bolts removed, slide the center bumper TOOLS REQUIRED panel forwards to remove. Trim Tool 9. If equipped, disconnect the parking sensors by the electrical connectors, and release the wiring clips to completely remove the center bumper panel.
  • Page 11 FB-IGR-G1-23-PR-ASM0 INEOS Grenadier 23+ Fitting Instruction Predator & Toro Front Bar RH SIDE SHOWN Top Outer 1x Torx Top Inner 1x Torx Underside 3x Torx Wheel Arch 2x Torx 10. Remove Torx head screws retaining the outer TOOLS REQUIRED bumper panel to the vehicle. Locations are shown in the image above.
  • Page 12 FB-IGR-G1-23-PR-ASM0 INEOS Grenadier 23+ Fitting Instruction Predator & Toro Front Bar RH SIDE SHOWN Release parking sensor + cable clips as pas per center section Slide back tab, then squeeze to release 12. Once the bumper panel is forward far enough for TOOLS REQUIRED access, disconnect the clearance light connector.
  • Page 13 FB-IGR-G1-23-PR-ASM0 INEOS Grenadier 23+ Fitting Instruction Predator & Toro Front Bar LH SIDE SHOWN 15. Once bumper panel is removed, replace the TOOLS REQUIRED factory screw that secures the corner of the auxiliary radiator mounts. T30 Torx Driver FASTENERS Factory Screw...
  • Page 14 FB-IGR-G1-23-PR-ASM0 INEOS Grenadier 23+ Fitting Instruction Predator & Toro Front Bar 16. NOTE: IF vehicle is NOT equipped with parking TOOLS REQUIRED sensors and a winch is NOT being fitted, it is possible to avoid removal of the headlight & trims,...
  • Page 15 FB-IGR-G1-23-PR-ASM0 INEOS Grenadier 23+ Fitting Instruction Predator & Toro Front Bar Unclip First 18. Remove the large headlight cover trim from the TOOLS REQUIRED vehicle. T30 Torx Driver 19. Remove the 4x Torx Screws securing trim panel to Trim Tool the vehicle.
  • Page 16 FB-IGR-G1-23-PR-ASM0 INEOS Grenadier 23+ Fitting Instruction Predator & Toro Front Bar Securing Bolts - Remove Alignment bolts – DO NOT REMOVE 22. Remove the Headlight. TOOLS REQUIRED 23. It is important to only release the Silver T40 T40 Torx Driver Securing screws, not the headlight alignment screws.
  • Page 17 FB-IGR-G1-23-PR-ASM0 INEOS Grenadier 23+ Fitting Instruction Predator & Toro Front Bar Parking Sensor Equipped vehicles ONLY Remove retaining Squeeze tab and pull Use screwdriver to Clip to disconnect release retaining clip 25. Disconnect the main parking sensor wiring harness TOOLS REQUIRED connector, accessed through the headlight opening.
  • Page 18 FB-IGR-G1-23-PR-ASM0 INEOS Grenadier 23+ Fitting Instruction Predator & Toro Front Bar LH SIDE SHOWN 29. Unclip the clearance light harness from the wheel TOOLS REQUIRED arch bracket. Trim Tool This will provide more length on the cable to re-plug into the relocated light in the bar.
  • Page 19 FB-IGR-G1-23-PR-ASM0 INEOS Grenadier 23+ Fitting Instruction Predator & Toro Front Bar 31. Remove the 2x T30 Screws holding the bash plate to TOOLS REQUIRED the center crossbeam. T30 Torx Driver FASTENERS Factory Screws (Discard) REV A 07/11/2024 Page 19 of 65...
  • Page 20 FB-IGR-G1-23-PR-ASM0 INEOS Grenadier 23+ Fitting Instruction Predator & Toro Front Bar RH SIDE SHOWN Pull off foam 16mm Socket 18mm Socket Remove Impact Beam 32. Remove the foam buffer from front the center TOOLS REQUIRED impact beam. 16mm Socket 33. Remove the 3x Bolts per side securing the aux...
  • Page 21 FB-IGR-G1-23-PR-ASM0 INEOS Grenadier 23+ Fitting Instruction Predator & Toro Front Bar 36. Remove the 2x T50 Torx screws securing the top of TOOLS REQUIRED the bash plate to the chassis. T50 Torx Driver 37. Remove the 4x T50 Torx Screws securing the bottom of the bash plate to the chassis.
  • Page 22 FB-IGR-G1-23-PR-ASM0 INEOS Grenadier 23+ Fitting Instruction Predator & Toro Front Bar RH SIDE SHOWN Impact Assy Flange sits BEHIND auxiliary radiator support 38. Fit the impact assemblies to the chassis. Insert the TOOLS REQUIRED impact assembly on an angle, such that it positions the side flange BEHIND the auxiliary radiator supports.
  • Page 23 FB-IGR-G1-23-PR-ASM0 INEOS Grenadier 23+ Fitting Instruction Predator & Toro Front Bar RH SIDE SHOWN 39. Secure the impact assembly to the chassis and TOOLS REQUIRED auxiliary radiator bracket, re-using the factory bolts and flange nuts removed from the impact beam.
  • Page 24 FB-IGR-G1-23-PR-ASM0 INEOS Grenadier 23+ Fitting Instruction Predator & Toro Front Bar MEASURE ADJUST 40. Measure Distance between outside edges uprights TOOLS REQUIRED on bar using tape measure. Write distance below for reference if required. 18mm Socket 16mm Socket Bar Upright Width = ___________mm Tape Measure 41.
  • Page 25 FB-IGR-G1-23-PR-ASM0 INEOS Grenadier 23+ Fitting Instruction Predator & Toro Front Bar RH SIDE SHOWN TOOLS REQUIRED 43. Cover the outer section of the plastic aux radiator air guides with masking tape, as shown. Masking Tape FASTENERS REV A 07/11/2024 Page 25 of 65...
  • Page 26 FB-IGR-G1-23-PR-ASM0 INEOS Grenadier 23+ Fitting Instruction Predator & Toro Front Bar RHS Shown TOP VIEW Side of Vehicle Crease Point A Point B 20mm RHS Shown BOTTOM VIEW Crease Point D 16mm Point C 28mm Side of Vehicle 44. Using a steel rule measure and mark the following...
  • Page 27 FB-IGR-G1-23-PR-ASM0 INEOS Grenadier 23+ Fitting Instruction Predator & Toro Front Bar RH SIDE SHOWN 46. Using a ruler and marker, mark a straight line between TOOLS REQUIRED the 4 points marked around the air guide in the previous Ruler step.
  • Page 28 FB-IGR-G1-23-PR-ASM0 INEOS Grenadier 23+ Fitting Instruction Predator & Toro Front Bar RH SIDE SHOWN 48. Using an air hacksaw or oscillating multi tool, cut along TOOLS REQUIRED the line marked. Air Hacksaw 49. Neaten up cut edges using file, utility knife or de-burring tool.
  • Page 29 Trim Tool 52. Take note of the side and orientation of the lamp units to ensure they are re-fitted in the same way 53. Retain lights for re-fitment to Offroad Animal Bar. FASTENERS REV A 07/11/2024...
  • Page 30 FB-IGR-G1-23-PR-ASM0 INEOS Grenadier 23+ Fitting Instruction Predator & Toro Front Bar 54. Remove all adhesive, and adhesive residue from the TOOLS REQUIRED clearance lights. Utility Knife Scraper 55. Remove the bulk of the adhesive using a knife or scraper, then clean the rest off using solvents / rag.
  • Page 31 FB-IGR-G1-23-PR-ASM0 INEOS Grenadier 23+ Fitting Instruction Predator & Toro Front Bar 57. Using tape kit supplied, apply adhesive tape to TOOLS REQUIRED perimeter of the clearance light. Scissors Utility Knife 58. Trim tape to length using scissors / knife as required.
  • Page 32 FB-IGR-G1-23-PR-ASM0 INEOS Grenadier 23+ Fitting Instruction Predator & Toro Front Bar Parking Sensor Equipped vehicles ONLY Push through from front whilst holding tabs apart 60. If fitted, Remove the parking sensors from both TOOLS REQUIRED the center and outer bumper segments. The removal process is the same for all sensors.
  • Page 33 FB-IGR-G1-23-PR-ASM0 INEOS Grenadier 23+ Fitting Instruction Predator & Toro Front Bar Parking Sensor Equipped vehicles ONLY Squeeze retaining tabs inwards, Push from behind to release housing through front 64. Once sensors are removed, remove the sensor TOOLS REQUIRED housings from the bumper.
  • Page 34 FB-IGR-G1-23-PR-ASM0 INEOS Grenadier 23+ Fitting Instruction Predator & Toro Front Bar Parking Sensor Equipped vehicles ONLY 67. Using a sharp utility knife, cut off the keying notch TOOLS REQUIRED on from the sensor housing. Utility Knife 68. Ensure the cut is flush at the bottom edge. The housing should look like the inset image once complete.
  • Page 35 FB-IGR-G1-23-PR-ASM0 INEOS Grenadier 23+ Fitting Instruction Predator & Toro Front Bar RH SIDE SHOWN 70. Re-fit the sensor housing and parking sensors to TOOLS REQUIRED the bar. 71. First insert the housing from the front side of the bar. Then fit the sensor back into the housing from the rear.
  • Page 36 FB-IGR-G1-23-PR-ASM0 INEOS Grenadier 23+ Fitting Instruction Predator & Toro Front Bar Parking Sensor Equipped vehicles ONLY 73. Before refitting the parking sensor loom, remove TOOLS REQUIRED all the stud clips, by carefully cutting off using side cutters. This will make the loom much easier to run through the bar.
  • Page 37 FB-IGR-G1-23-PR-ASM0 INEOS Grenadier 23+ Fitting Instruction Predator & Toro Front Bar Parking Sensor Equipped vehicles ONLY 76. Re-connect the parking sensor electrical TOOLS REQUIRED connectors. 77. Using cable ties, tidy and secure loom to the bar FASTENERS Cable ties REV A...
  • Page 38 FB-IGR-G1-23-PR-ASM0 INEOS Grenadier 23+ Fitting Instruction Predator & Toro Front Bar LH SIDE SHOWN 78. Using isopropyl alcohol or a rag, clean the TOOLS REQUIRED surfaces around the clearance light hole in the wing. 3M Primer Stick 79. Break the ampule on the 3M primer 94 stick, by Isopropyl Alcohol squeezing in the location indicated on the tube.
  • Page 39 FB-IGR-G1-23-PR-ASM0 INEOS Grenadier 23+ Fitting Instruction Predator & Toro Front Bar Cage Cage B-1342L/R 2x 2MM Cage Nut B-1341 2x 2MM Cage Nut B-1343L/R 1x 3MM Cage Nut 82. Whilst waiting for the adhesion promoter to cure, TOOLS REQUIRED fit the cage nuts to parts that require them.
  • Page 40 FB-IGR-G1-23-PR-ASM0 INEOS Grenadier 23+ Fitting Instruction Predator & Toro Front Bar LH SIDE SHOWN 89. Fit the under-panel support brackets to the slots in the TOOLS REQUIRED bottom edge of the wing, using M6x16 Hex bolts, Flat Washers and Flange nuts. Leave finger tight at this stage 90.
  • Page 41 FB-IGR-G1-23-PR-ASM0 INEOS Grenadier 23+ Fitting Instruction Predator & Toro Front Bar LH SIDE SHOWN M6x16mm + Flat Washer + Flange Nut 92. Fit the Inner Arch Liner Brackets to the slots in the back TOOLS REQUIRED edge of the wing, using M6x16 Hex bolts, Flat Washers and Flange nuts.
  • Page 42 FB-IGR-G1-23-PR-ASM0 INEOS Grenadier 23+ Fitting Instruction Predator & Toro Front Bar RH SIDE SHOWN 94. Taking care to ensure the correct orientation is TOOLS REQUIRED maintained, fit the clearance lamps to the cutouts in Utility Knife or the bar, using the previously applied 3M tape.
  • Page 43 FB-IGR-G1-23-PR-ASM0 INEOS Grenadier 23+ Fitting Instruction Predator & Toro Front Bar Antenna Mount Hole Flip to Bar 2x M6x20 Hex, Flat Washer and Flange Number Plate to Flip 2x From Outside-> Inside M5x15 Pan Head, Flat M8x25 Hex > M8 Flat Washer Washer and Flange Nut >...
  • Page 44 FB-IGR-G1-23-PR-ASM0 INEOS Grenadier 23+ Fitting Instruction Predator & Toro Front Bar 100. Temporarily re-fit the headlight surround TOOLS REQUIRED panel, to allow reference for alignment of bar. T30 Torx Driver 101. It is not necessary to refit all fasteners, but ensure the panel is sitting in the correct location and secure.
  • Page 45 FB-IGR-G1-23-PR-ASM0 INEOS Grenadier 23+ Fitting Instruction Predator & Toro Front Bar 102. With assistance, either from another TOOLS REQUIRED person, or a lifting trolley, lift the bar onto the mounts on the vehicle. Lifting Trolley 103. Push the bar onto the mounts to check full range of adjustment.
  • Page 46 FB-IGR-G1-23-PR-ASM0 INEOS Grenadier 23+ Fitting Instruction Predator & Toro Front Bar RH SIDE SHOWN 104. Secure with 4x M12x30 Bolts, Heavy Duty TOOLS REQUIRED washers and M12 Nyloc and Flange Nuts per side, Finger tight at this stage. Lifting Trolley...
  • Page 47 FB-IGR-G1-23-PR-ASM0 INEOS Grenadier 23+ Fitting Instruction Predator & Toro Front Bar LH SIDE SHOWN Approx. 20mm Wing Tip To edge 15-25mm Maintain 10-15mm of Flare Clearance Clearance IN FRONT of body for top edge. 106. With assistance from another person, Align TOOLS REQUIRED the bar with the edges of the vehicle.
  • Page 48 FB-IGR-G1-23-PR-ASM0 INEOS Grenadier 23+ Fitting Instruction Predator & Toro Front Bar RH SIDE SHOWN 109. If NOT fitting a winch, Fit the winch cover TOOLS REQUIRED panel brackets to the bar using M6x16 button head bolts, Flat washers and flange nuts supplied with the 4mm Hex Key winch cover kit.
  • Page 49 FB-IGR-G1-23-PR-ASM0 INEOS Grenadier 23+ Fitting Instruction Predator & Toro Front Bar 111. If fitting a winch, do so now. TOOLS REQUIRED 112. First, fit the winch fairlead to the bar, using 16mm socket / spanner fasteners supplied with winch fairlead. Note that this bar will only suit slimline hawse type fairleads.
  • Page 50 FB-IGR-G1-23-PR-ASM0 INEOS Grenadier 23+ Fitting Instruction Predator & Toro Front Bar Connect Winch Positive to This Terminal on Contactor 500A Contactor Headlight opening 115. For vehicles equipped with “High Load TOOLS REQUIRED Auxiliary Switch Panel & Electrical Preparation” the 17mm Stubby Spanner...
  • Page 51 FB-IGR-G1-23-PR-ASM0 INEOS Grenadier 23+ Fitting Instruction Predator & Toro Front Bar Winch Earth Point 117. For vehicles equipped with “High Load TOOLS REQUIRED Auxiliary Switch Panel & Electrical Preparation” the 13mm Spanner winch negative needs to be connected to the dedicated earthing stud located on the RH chassis rail.
  • Page 52 FB-IGR-G1-23-PR-ASM0 INEOS Grenadier 23+ Fitting Instruction Predator & Toro Front Bar Parking Sensor Equipped vehicles ONLY 119. If Vehicle equipped with parking sensors. Re TOOLS REQUIRED connect the main parking sensor loom behind the headlight. Remember to replace the retaining clip.
  • Page 53 FB-IGR-G1-23-PR-ASM0 INEOS Grenadier 23+ Fitting Instruction Predator & Toro Front Bar RH SIDE SHOWN 120. From underneath, reconnect the side TOOLS REQUIRED clearance lamp electrical connectors. 121. Repeat for both sides FASTENERS REV A 07/11/2024 Page 53 of 65...
  • Page 54 FB-IGR-G1-23-PR-ASM0 INEOS Grenadier 23+ Fitting Instruction Predator & Toro Front Bar RH SIDE SHOWN Insert M6x16 + Flat Washer Cut off Tab Align Cage Nuts Flex wheel arch into position and bolt to wing standoff bracket 122. Using Side cutters, cut of the tabs on the...
  • Page 55 FB-IGR-G1-23-PR-ASM0 INEOS Grenadier 23+ Fitting Instruction Predator & Toro Front Bar RH SIDE SHOWN 127. Once the inner arch bracket is connected, TOOLS REQUIRED tighten the M6 bolts securing the bracket to the wing, using 10mm socket or spanner 10mm Socket or Spanner 128.
  • Page 56 FB-IGR-G1-23-PR-ASM0 INEOS Grenadier 23+ Fitting Instruction Predator & Toro Front Bar RH SIDE SHOWN M8x20 Hex Head, Bracket, Bar, Flange Nut 129. Fit Under-panel Centre Braces to the Winch TOOLS REQUIRED cradle, using supplied M8x20 Hex Bolt Flat washer and Flange Nut. Leave bolt finger tight at this stage.
  • Page 57 FB-IGR-G1-23-PR-ASM0 INEOS Grenadier 23+ Fitting Instruction Predator & Toro Front Bar 132. Replace the headlight and all trims on the TOOLS REQUIRED RH front headlight, re using all original fasteners. T30,40 Torx Driver 133. The refit procedure is reverse of removal.
  • Page 58 FB-IGR-G1-23-PR-ASM0 INEOS Grenadier 23+ Fitting Instruction Predator & Toro Front Bar 134. Using the adhesive backing, fit the TOOLS REQUIRED compliance plate to the underside of the winch cradle. 6MM Hex Key 16/17 mm Socket / Spanner 135. Fit Center Bash Plate. As the bash plate is...
  • Page 59 FB-IGR-G1-23-PR-ASM0 INEOS Grenadier 23+ Fitting Instruction Predator & Toro Front Bar LH SIDE SHOWN 139. Fit 3x M6x2mm Cage nuts to each of the side TOOLS REQUIRED under panels. Flat blade Screwdriver 140. It can be helpful to use a small flat blade screwdriver to push the cage nut into the square slot.
  • Page 60 FB-IGR-G1-23-PR-ASM0 INEOS Grenadier 23+ Fitting Instruction Predator & Toro Front Bar LH SIDE SHOWN Hold up under panel and align 141. Test Fit Side Under panels holding them in TOOLS REQUIRED position and aligning the bolt holes. Adjust position of under panel brackets to suit.
  • Page 61 FB-IGR-G1-23-PR-ASM0 INEOS Grenadier 23+ Fitting Instruction Predator & Toro Front Bar LH SIDE SHOWN M6x16 Button Head M6 Flat Washer into Cage Nut 143. Fit Side Under panels using, 6x M6x16 TOOLS REQUIRED button head and flat washer into the cage nuts placed earlier.
  • Page 62 FB-IGR-G1-23-PR-ASM0 INEOS Grenadier 23+ Fitting Instruction Predator & Toro Front Bar LH SIDE SHOWN M6x16 Button Head M6 Flat Washer into Cage Nut 145. Secure the inner wheel arch liner to the TOOLS REQUIRED bottom of the side under panel using 3x M6 25...
  • Page 63 FB-IGR-G1-23-PR-ASM0 INEOS Grenadier 23+ Fitting Instruction Predator & Toro Front Bar TORO BARS ONLY M8x20 Button Head Flat Washer 148. If required, fit antenna brackets to the TOOLS REQUIRED threaded inserts behind bar upright using M8x20 Button Head bolts and Flat Washers.
  • Page 64 FB-IGR-G1-23-PR-ASM0 INEOS Grenadier 23+ Fitting Instruction Predator & Toro Front Bar Tighten Under-panel RH SIDE SHOWN Centre Braces 152. Using a 13mm spanner, with access from TOOLS REQUIRED behind the winch, tighten the M8 bolt securing the 5mm Hex Key Under-panel Centre Braces to the winch cradle.
  • Page 65 FB-IGR-G1-23-PR-ASM0 INEOS Grenadier 23+ Fitting Instruction Predator & Toro Front Bar 157. Check all Fasteners are tight. 158. Re-Fit number plate to number plate flip, if not done earlier. 159. Head Bush and Enjoy your newly protected Grenadier! REV A...