Advertisement
Quick Links
Offroad Animal
IMPORTANT! – READ BEFORE INSTALLATION
•
When installed in accordance with these instructions, the front protection bar does
not affect the operation of the vehicles SRS airbags.
•
This product must be installed exactly as per these instructions using only
hardware supplied.
•
Take a few moments to read instructions thoroughly before beginning work.
•
In the event of damage to any component please contact OFFROAD ANIMAL to
arrange repair/replacement of components.
•
Do not use this product for any vehicle make or model other than that specified on
these instructions.
•
Do not remove labels from this product.
•
This product and its fixings must not be modified in any way unless stated in these
fitting instructions.
•
The installation of this product is recommended for trained personnel.
•
These instructions are correct at time of publication. OFFROAD ANIMAL cannot
be held responsible for the impact of any changes subsequently made by the
vehicle manufacturer. If you find something has changed please contact us to let
us know!
•
During installation it is the duty of the installer to check correct
operation/clearances of all components.
•
If Instructions are to be printed for reference in the workshop, it is recommended
that they are printed in colour, for best legibility.
•
Estimated install time: 2 hours
REV NIL
PR-JGC-WK2-11-ASM0
Fitting Instruction
28/1/20
2011-2013 Jeep Grand Cherokee
Pre-Runner/ Steel front bumper
Page 1 of 24
Advertisement
Related Manuals for Offroad Animal PR-JGC-WK2-11-ASM0
Summary of Contents for Offroad Animal PR-JGC-WK2-11-ASM0
- Page 1 • Take a few moments to read instructions thoroughly before beginning work. • In the event of damage to any component please contact OFFROAD ANIMAL to arrange repair/replacement of components. • Do not use this product for any vehicle make or model other than that specified on these instructions.
- Page 2 Offroad Animal PR-JGC-WK2-11-ASM0 2011-2013 Jeep Grand Cherokee Fitting Instruction Pre-Runner/ Steel front bumper IMPORTANT: Check all parts are present before beginning work! Contact OFFROAD ANIMAL if something is missing. Main Parts – In the Box Part Number Description Image PR-JGC-...
- Page 3 Offroad Animal PR-JGC-WK2-11-ASM0 2011-2013 Jeep Grand Cherokee Fitting Instruction Pre-Runner/ Steel front bumper B-0319R Wk2 Pre-Runner wing RH P-0021 Acc Cover Pre-Runner wing support B-0324L Pre-Runner Wing support B-0324R Optional extra ACC Acc mount wk2 mount part B-0062 Optional extra ACC...
-
Page 4: Power Tools
M10 x 30 Hex Bolt ZP M10 x 45 M10 x 45 Hex Bolt, Zinc Plate OFA-LOGO OFFROAD ANIMAL METAL LOGO Pinch Weld 2M Pinch Weld Black 14mm x 9mm x 2M M5 x 30 pan M5 x 30 Pan head screw zinc Optional extra... - Page 5 Offroad Animal PR-JGC-WK2-11-ASM0 2011-2013 Jeep Grand Cherokee Fitting Instruction Pre-Runner/ Steel front bumper Take Care not to lose factory hardware, as some will be reused Take care not to damage parking sensors, They may be disturbed by the new bumper. Sorry it’s their position and this can’t be helped with this new bumper.
-
Page 6: Tools Required
Offroad Animal PR-JGC-WK2-11-ASM0 2011-2013 Jeep Grand Cherokee Fitting Instruction Pre-Runner/ Steel front bumper TOOLS REQUIRED 1. First step is to remove the lower air damn fascia. To do this None climb under your Jeep and remove all 5 quarter turn clips by hand. - Page 7 Offroad Animal PR-JGC-WK2-11-ASM0 2011-2013 Jeep Grand Cherokee Fitting Instruction Pre-Runner/ Steel front bumper 3. Remove factory Lower Radiator Cover. 3x M6 bolts on front TOOLS REQUIRED and 2x M8 bolts on back. Use 10mm socket or spanner for front and 13mm for rear...
- Page 8 Offroad Animal PR-JGC-WK2-11-ASM0 2011-2013 Jeep Grand Cherokee Fitting Instruction Pre-Runner/ Steel front bumper TOOLS REQUIRED 4. Remove factory tie down and or tow points Socket set FASTENERS Discard fasteners REV NIL 28/1/20 Page 8 of 24...
- Page 9 PR-JGC-WK2-11-ASM0 2011-2013 Jeep Grand Cherokee Fitting Instruction Pre-Runner/ Steel front bumper TOOLS REQUIRED 5. Stack Offroad Animal Tow points together as shown with M10 bolts and M10 flat washers. FASTENERS M10x80 Hex bolts (4) M10 Flat Washers (4) REV NIL...
- Page 10 2011-2013 Jeep Grand Cherokee Fitting Instruction Pre-Runner/ Steel front bumper 6. Fit Offroad Animal Tow points as shown on LH and RH side TOOLS REQUIRED with M10x80 bolts directly into frame of Jeep. Torque down bolts. Be aware if fitting a nudge bar you may need to...
- Page 11 Offroad Animal PR-JGC-WK2-11-ASM0 2011-2013 Jeep Grand Cherokee Fitting Instruction Pre-Runner/ Steel front bumper 7. If Adaptive cruise control is fitted, unplug loom and pull TOOLS REQUIRED sensor off posts. If you do not have ACC, skip this step 8. Remove bracket...
- Page 12 Offroad Animal PR-JGC-WK2-11-ASM0 2011-2013 Jeep Grand Cherokee Fitting Instruction Pre-Runner/ Steel front bumper 9. Fit side support bars as shown on both sides. TOOLS REQUIRED 10. Remove lower factory bolt, place bracket on and reuse factory bolt 13mm spanner or socket...
- Page 13 Offroad Animal PR-JGC-WK2-11-ASM0 2011-2013 Jeep Grand Cherokee Fitting Instruction Pre-Runner/ Steel front bumper 11. Fit pinch weld to top edge of main plate and wings TOOLS REQUIRED FASTENERS REV NIL 28/1/20 Page 13 of 24...
- Page 14 Offroad Animal PR-JGC-WK2-11-ASM0 2011-2013 Jeep Grand Cherokee Fitting Instruction Pre-Runner/ Steel front bumper 12. Trim edges of pinch weld at edge of plate TOOLS REQUIRED Side cutters FASTENERS REV NIL 28/1/20 Page 14 of 24...
- Page 15 Offroad Animal PR-JGC-WK2-11-ASM0 2011-2013 Jeep Grand Cherokee Fitting Instruction Pre-Runner/ Steel front bumper 13. Fit Pre runner mounts as shown with M10 x 30 bolts, TOOLS REQUIRED washers and flange nuts 16 or 17mm Spanner and or socket FASTENERS M10 x 30 (4)
- Page 16 Offroad Animal PR-JGC-WK2-11-ASM0 2011-2013 Jeep Grand Cherokee Fitting Instruction Pre-Runner/ Steel front bumper 14. Fit Pre Runner Upper Mounts to top of Tow points. Secure TOOLS REQUIRED to Main plate M10 x 45 Bolts, flat washers and Flange nuts as shown.
- Page 17 Offroad Animal PR-JGC-WK2-11-ASM0 2011-2013 Jeep Grand Cherokee Fitting Instruction Pre-Runner/ Steel front bumper 17. Using the factory M6 bolts secure through the bottom of TOOLS REQUIRED the Pre runner centre plate 10mm socket or spanner FASTENERS Factory M6 screws REV NIL...
- Page 18 Offroad Animal PR-JGC-WK2-11-ASM0 2011-2013 Jeep Grand Cherokee Fitting Instruction Pre-Runner/ Steel front bumper 18. Fit wings as shown, using M8 hardware. Reach in from TOOLS REQUIRED behind bumper to fit nut on back 5mm allen key 19. Repeat for other side...
- Page 19 Offroad Animal PR-JGC-WK2-11-ASM0 2011-2013 Jeep Grand Cherokee Fitting Instruction Pre-Runner/ Steel front bumper 20. Position the wings to have the smallest gap possible TOOLS REQUIRED between wings and centre. Torque up bolts 5mm Allen key FASTENERS REV NIL 28/1/20 Page 19 of 24...
- Page 20 Offroad Animal PR-JGC-WK2-11-ASM0 2011-2013 Jeep Grand Cherokee Fitting Instruction Pre-Runner/ Steel front bumper 21. Fit Bolt through wing into support bracket TOOLS REQUIRED 22. Repeat for other side 5mm Allen Key FASTENERS M8 x 20 BHCS black (2) M8 flat washer (2)
- Page 21 Offroad Animal PR-JGC-WK2-11-ASM0 2011-2013 Jeep Grand Cherokee Fitting Instruction Pre-Runner/ Steel front bumper 23. If no Adaptive cruise control is fitted, then fit ACC cover TOOLS REQUIRED plate with M8 x 16 button head cap screws (black zinc), flat washers and flange nuts 4mm Allen Key 24.
- Page 22 Pre-Runner/ Steel front bumper 25. If you have Adaptive cruise control you will need optional TOOLS REQUIRED Offroad Animal Part “ PR-JGC-WK2-14-ASM3” 26. Fit Radar sensor to Acc Mount Wk2 plate with supplied M5 Phillips head screw driver x 30 pan head screws in optional kit 13mm spanner or socket 27.
- Page 23 Offroad Animal PR-JGC-WK2-11-ASM0 2011-2013 Jeep Grand Cherokee Fitting Instruction Pre-Runner/ Steel front bumper 29. Torque up all front bolts TOOLS REQUIRED 5mm Allen key FASTENERS REV NIL 28/1/20 Page 23 of 24...
- Page 24 Offroad Animal PR-JGC-WK2-11-ASM0 2011-2013 Jeep Grand Cherokee Fitting Instruction Pre-Runner/ Steel front bumper 30. Fit logo plate to bumper. If fitting nudge bar hold off until TOOLS REQUIRED that is on before doing this step. 31. You’re done, enjoy the coolness that is your Jeep now.