SMC Networks 6900FSC Installation Manual

Tigerswitch 10/100 stackable fast ethernet switch
Hide thumbs Also See for 6900FSC:
Table of Contents

Advertisement

TigerSwitch 10/100
Stackable Fast Ethernet Switch
N 12/24 10BASE-T/100BASE-TX ports
N Optional 100BASE-FX or 1000BASE-SX modules
N Optional stack module for linking up to four units
N 8.8 Gbps of aggregate switch bandwidth
N Support for redundant power unit
N Up to five port trunks per switch
N Port mirroring for non-intrusive analysis
N QoS support for two-level priority
N Full support for VLANs with GVRP
N IP Multicasting with IGMP Snooping
N Manageable via console, Web, SNMP/RMON

Installation Guide

SMC6912M
SMC6924M

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 6900FSC and is the answer not in the manual?

Questions and answers

Summary of Contents for SMC Networks 6900FSC

  • Page 1: Installation Guide

    TigerSwitch 10/100 Stackable Fast Ethernet Switch N 12/24 10BASE-T/100BASE-TX ports N Optional 100BASE-FX or 1000BASE-SX modules N Optional stack module for linking up to four units N 8.8 Gbps of aggregate switch bandwidth N Support for redundant power unit N Up to five port trunks per switch N Port mirroring for non-intrusive analysis N QoS support for two-level priority N Full support for VLANs with GVRP...
  • Page 3 TigerSwitch 10/100 Installation Guide From SMC’s Tiger line of feature-rich workgroup LAN solutions 6 Hughes Irvine, CA 92618 February 2001 Phone: (949) 707-2400 Pub. # F2.42 150070-102 R05...
  • Page 4 Irvine, CA 92618 All rights reserved. Printed in Taiwan Trademarks: SMC is a registered trademark; and EZ Switch, TigerStack and TigerSwitch are trademarks of SMC Networks, Inc. Other product and company names are trademarks or registered trademarks of their respective holders.
  • Page 5: Limited Warranty

    30 days of purchase from SMC or its Authorized Reseller. Registration can be accomplished via the enclosed product registration card or online via the SMC web site. Failure to register will not affect the standard limited warranty. The Limited Lifetime warranty covers a product during the Life of that Product, which is defined as the period of time during which the product is an “Active”...
  • Page 6 WHICH MAY VARY FROM STATE TO STATE. NOTHING IN THIS WARRANTY SHALL BE TAKEN TO AFFECT YOUR STATUTORY RIGHTS. * SMC will provide warranty service for one year following discontinuance from the active SMC price list. Under the limited lifetime warranty, internal and external power supplies, fans, and cables are covered by a standard one-year warranty from date of purchase.
  • Page 7 EC Conformance Declaration - Class A SMC contact for these products in Europe is: SMC Networks Europe, Edificio Conata II, Calle Fructuós Gelabert 6-8, 2 08970 - Sant Joan Despí,...
  • Page 8: Japan Vcci Class A

    “Appareils Numériques,” NMB-003 édictée par le ministère des Communications. Japan VCCI Class A Taiwan BSMI Class A Australia AS/NZS 3548 (1995) - Class A SMC contact for products in Australia is: SMC Communications Pty. Ltd. Suite 18, 12 Tryon Road, Lindfield NSW2070,...
  • Page 9: Safety Compliance

    OMPLIANCES Safety Compliance Warning: Fiber Optic Port Safety When using a fiber optic port, never look at the transmit laser while it is powered on. Also, never look directly at the fiber TX port and fiber cable ends when they are powered on. Avertissment: Ports pour fibres optiques - sécurité...
  • Page 10 OMPLIANCES Wichtige Sicherheitshinweise (Germany) 1. Bitte lesen Sie diese Hinweise sorgfältig durch. 2. Heben Sie diese Anleitung für den späteren Gebrauch auf. 3. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Verwenden Sie keine Flüssigoder Aerosolreiniger. Am besten eignet sich ein angefeuchtetes Tuch zur Reinigung.
  • Page 11: Table Of Contents

    Maximum 1000BASE-SX Fiber Optic Cable Distance 2-6 100 Mbps Fast Ethernet Collision Domain ... 2-7 SMC 3-2 Rule for Class II Repeaters ... . . 2-7...
  • Page 12 ABLE OF ONTENTS SMC 2-1 Rule for Class I Repeaters ... . 2-7 Maximum Network Diameter Using Repeaters ..2-7 Maximum Fast Ethernet Cable Distance ..2-7 10 Mbps Ethernet Collision Domain .
  • Page 13 ABLE OF ONTENTS Straight-Through Wiring .....B-3 Crossover Wiring ......B-4 Console Port Pin Assignments .
  • Page 14 ABLE OF ONTENTS viii...
  • Page 15: About The Tigerswitch 10/100

    IGER WITCH Overview SMC’s TigerSwitch™ 10/100 is a stackable switch with 12 or 24 10BASE-T/100BASE-TX ports, plus two slots for optional slide-in 100BASE-FX or 1000BASE-SX modules. One of these slots can also be used for an optional stacking module that allows you attach up to four switches to a 4.8 Gbps high-speed backplane.
  • Page 16: Switch Architecture

    10/100 BOUT THE IGER WITCH Rear Panel (Both Models) Figure 1-2. Rear Panel 100BASE-FX Fiber Module 1000BASE-SX Gigabit Module Stack Module Figure 1-3. Optional Modules Switch Architecture The TigerSwitch employs a high-speed switching fabric. This design allows for simultaneous transport of multiple packets at low latency on all ports.
  • Page 17: Management Options

    10/100 BOUT THE IGER WITCH Management Options This switch contains a comprehensive array of LEDs for “at-a-glance” monitoring of network and port status. It also includes a Network Management Module that allows the entire stack to be managed in-band via SNMP or RMON (Groups 1, 2, 3 and 9) protocols, with a Web browser, or remotely via Telnet.
  • Page 18: Status Leds

    10/100 BOUT THE IGER WITCH Status LEDs The LEDs, which are located on the front panel for easy viewing, are shown below and described in the following table. Figure 1-4. Port and System LEDs Port and System Status LEDs Condition Status Power Switch is receiving power.
  • Page 19: Network Management Module

    10/100 BOUT THE IGER WITCH Port and System Status LEDs Condition Status Module Ports A module is installed in this slot. Status Activity Traffic is passing through the module. Network Management Module Figure 1-5. Network Management Module This switch includes a Network Management Module on the rear panel.
  • Page 20: Spanning Tree Protocol

    10/100 BOUT THE IGER WITCH eliminates the loss of packets due to bottlenecks caused by port saturation. And broadcast storm control prevents broadcast traffic storms from engulfing the network. Some of this switch’s advanced features are described below. For a detailed description, refer to the Management Guide.
  • Page 21: Multicast Switching

    10/100 BOUT THE IGER WITCH • Provides data security by restricting all traffic to the originating VLAN, except where a connection has been configured between separate VLANs using a router or Layer 3 switch. Multicast Switching Specific multicast traffic can be assigned to its own VLAN to ensure that it does not interfere with normal network traffic and to guarantee real-time delivery by setting the required priority level for the designated VLAN.
  • Page 22: Optional 1000Base-Sx Module (Smc6900G)

    A stack cable is included with each module. Optional Redundant Power Unit (SMCRPU150W) SMC provides an optional Redundant Power Unit (RPU), SMCRPU150W, that can supply power to the switch in the event of failure of the internal power supply.
  • Page 23: Power Supply Receptacles

    10/100 BOUT THE IGER WITCH Power Supply Receptacles There are two power receptacles on the rear panel of the switch. The standard power receptacle is for the AC power cord. The receptacle labeled “DC Input” is for the optional Redundant Power Unit (RPU).
  • Page 24: Features And Benefits

    10/100 BOUT THE IGER WITCH Features and Benefits Connectivity N 12 or 24 dual-speed ports for easy Fast Ethernet integration and for protection of your investment in legacy LAN equipment N Auto-negotiation enables each RJ-45 port to automatically select the optimum communication mode (half or full duplex and 10 or 100 Mbps) if this feature is supported by the attached device;...
  • Page 25: Performance

    10/100 BOUT THE IGER WITCH Performance N Transparent bridging N Aggregate bandwidth up to 8.8 Gbps N Switching Table with 12K MAC address entries N Provides Store-and-Forward switching N Filtering and forwarding at line speed N Broadcast storm control N Includes support for an optional Redundant Power Unit N Desktop or rack-mountable N Limited lifetime warranty Management...
  • Page 26 10/100 BOUT THE IGER WITCH • Port trunking increases the bandwidth of a network connection and ensures fault recovery • Port security prevents intruders from gaining access to the network 1-12...
  • Page 27: Network Planning

    HAPTER ETWORK LANNING Introduction to Switching A network switch allows simultaneous transmission of multiple packets via non-crossbar switching. This means that it can partition a network more efficiently than bridges or routers. The switch has, therefore, been recognized as one of the most important building blocks for today’s networking technology.
  • Page 28: Sample Applications

    ETWORK LANNING Sample Applications The TigerSwitch 10/100 is not only designed to segment your network, but also to provide a wide range of options in setting up network connections. Some typical applications are described below. Collapsed Backbone The TigerSwitch 10/100 is an excellent choice for mixed Ethernet and Fast Ethernet installations where significant growth is expected in the near future.
  • Page 29: Central Wiring Closet

    In the figure below, the 10BASE-T/100BASE-TX ports on the TigerSwitch stack are providing 100 Mbps connectivity for up to 100 segments through SMC’s TigerStack™ II 10/100 hubs. In addition, the switch is also connecting servers at 200 Mbps. Figure 2-2. Central Wiring Closet...
  • Page 30: Remote Connections With Fiber Cable

    ETWORK LANNING Remote Connections with Fiber Cable Fiber optic technology allows for longer cabling than any other media type (up to 2 kilometers for 100 Mbps fiber at full duplex, or up to 550 meters for 1 Gbps fiber). The TigerSwitch can serve as a collapsed backbone, providing direct connectivity for a widespread LAN.
  • Page 31: Making Vlan Connections

    ETWORK LANNING Making VLAN Connections VLANs can be based on port groups, or each data frame can be explicitly tagged to identify the VLAN group it belongs to. When using port-based VLANs, ports can either be assigned to any number of groups. Port-based VLANs are suitable for small networks.
  • Page 32: Connectivity Rules

    ETWORK LANNING Connectivity Rules When adding hubs (repeaters) to your network, please follow the connectivity rules listed below for Ethernet, Fast Ethernet, or Gigabit Ethernet. However, note that because switches break up the path for connected devices into separate collision domains, you should not include the switch or connected cabling in your calculations for cascade length involving other devices.
  • Page 33: 100 Mbps Fast Ethernet Collision Domain

    ETWORK LANNING 100 Mbps Fast Ethernet Collision Domain SMC 3-2 Rule for Class II Repeaters Between any two PCs or other stations in the same 100BASE-TX collision domain, there may be: • up to 3 link segments and • up to 2 Class II repeaters (hubs)
  • Page 34: 10 Mbps Ethernet Collision Domain

    ETWORK LANNING 10 Mbps Ethernet Collision Domain SMC 5-4-3 Rule Between any two PCs or other stations in the same 10 Mbps collision domain, there may be: • up to 5 link segments in series, • up to 4 repeaters (hubs), •...
  • Page 35: Application Notes

    ETWORK LANNING Application Notes 1. Full-duplex operation only applies to point-to-point access (such as when a switch is attached to a workstation, server or another switch). When the switch is connected to a hub, both devices must operate in half-duplex mode. 2.
  • Page 36 ETWORK LANNING 2-10...
  • Page 37: Installing The Switch

    HAPTER NSTALLING THE WITCH Selecting a Site TigerSwitch 10/100 units can be mounted in a standard 19-inch equipment rack or on a flat surface. Be sure to follow the guidelines below when choosing a location. N The site should: • be at the center of all the devices you want to link and near a power outlet.
  • Page 38: Equipment Checklist

    N Power Cord—either US, Continental Europe or UK N RS-232 console cable N This Installation Guide N SMC Warranty Registration Card—be sure to complete and return to SMC Optional Rack-Mounting Equipment If you plan to rack-mount the switch, be sure to have the...
  • Page 39: Mounting

    NSTALLING THE WITCH Mounting A TigerSwitch 10/100 unit can be mounted in a standard 19-inch equipment rack or on a desktop or shelf. Mounting instructions for each type of site follow. Before mounting the devices, be sure to install any optional modules, as follows.
  • Page 40 NSTALLING THE WITCH To rack-mount devices: 1. Attach the brackets to the device using the screws provided in the Bracket Mounting Kit. Figure 3-1. Attaching the Brackets 2. Mount the device in the rack, using four rack-mounting screws (not provided). Figure 3-2.
  • Page 41: Desktop Or Shelf Mounting

    NSTALLING THE WITCH 3. If installing a single switch only, turn to “Connecting to a Power Source” at the end of this chapter. 4. If installing multiple switches, mount them in the rack, one below the other, in any order. 5.
  • Page 42: Stacking

    NSTALLING THE WITCH Stacking A stack may have as many as four switches. Note: A stacking cable is included with the Stack Module. Caution: DO NOT stack TigerSwitch 10/100 units with other devices. Doing so may damage the switch. To stack the devices: 1.
  • Page 43: Connecting To A Power Source

    NSTALLING THE WITCH Connecting to a Power Source To connect a device to a power source: Note: It is recommended that the switches be stacked before being connected to a power source. However, a device can be added to the top or bottom of a stack that is on and operating without first powering down the stack.
  • Page 44 NSTALLING THE WITCH 4. If you have a purchased Redundant Power Unit, connect it to the device and to an AC power source now, following the instructions included with the package.
  • Page 45: Making Network Connections

    HAPTER AKING ETWORK ONNECTIONS Connecting Network Devices The TigerSwitch 10/100 is designed to interconnect multiple segments (or collision domains). It may be connected to 10 or 100 Mbps network cards in PCs and servers, as well as to Ethernet and Fast Ethernet hubs, switches or routers.
  • Page 46 AKING ETWORK ONNECTIONS (MDI-X). Since network cards do not cross their internal wiring to make a connection, PCs can be connected to these ports with straight-through cable. 10BASE-T/100BASE-TX hubs and switches, on the other hand, may have either crossover (MDI-X) or straight-through (MDI) ports. For this reason, the type of cable used to connect these devices to the TigerSwitch is determined by the port on the other device, as shown in the table below.
  • Page 47: Connecting To Pcs, Servers, Hubs And Switches

    AKING ETWORK ONNECTIONS Connecting to PCs, Servers, Hubs and Switches 1. Attach one end of a twisted-pair cable segment to the device’s RJ-45 connector. Figure 4-1. Figure 4-1. Making Twisted-Pair Connections 2. If the device is a network card and the TigerSwitch is in the wiring closet, attach the other end of the cable segment to a modular wall outlet that is connected to the wiring closet (see “Wiring Closet Connections”...
  • Page 48: Wiring Closet Connections

    AKING ETWORK ONNECTIONS Wiring Closet Connections Today, the punch-down block is an integral part of many of the newer equipment racks. It is actually part of the patch panel. Instructions for making connections in the wiring closet with this type of equipment follows. 1.
  • Page 49: Fiber Optic Devices

    SC connector at both ends. If you need to connect to a device with 62.5/125 micron cable that has ST-type connectors, SMC provides an optional SC-ST Converter (Part Number: 99-012034-091). Warning: This switch uses lasers to transmit signals over fiber optic cable.
  • Page 50 AKING ETWORK ONNECTIONS Figure 4-3. Making SC Port Connections 4. As a connection is made, check the Activity LED on the switch’s front panel for the corresponding module to be sure that the connection is valid. Note: If you use the optional SC-ST Converter, be sure to connect the converter’s Tx (Rx) port to the Rx (Tx) port on the other device.
  • Page 51: Troubleshooting

    • The switch is either downloading firmware or running the Power-On Self-Diagnostics Test (POST). If this LED does not stop flashing, then POST has failed, and you should contact SMC Technical Support. Link LED is Off • Verify that the switch and attached device are powered on.
  • Page 52: Power And Cooling Problems

    If you still cannot isolate the problem, then the internal power supply may be defective. In this case, contact SMC Technical Support for assistance. Installation Verify that all system components have been properly installed.
  • Page 53 ROUBLESHOOTING Note: You can configure the management agent to accept from one to four simultaneous Telnet sessions. If the maximum number of sessions already exists, an additional Telnet connection will not be able to log into the system.
  • Page 54 ROUBLESHOOTING...
  • Page 55: B Cables

    100BASE-FX and 1000BASE-SX Duplex Fiber Cable Cable Type Connector 62.5/125 or 50/125 micron core Note: If you need to connect to a device with 62.5/125 micron cable that has ST-type connectors, SMC provides an optional SC-ST Converter (Part Number: 99-012034-091).
  • Page 56 ABLES Twisted-Pair Cable and Pin Assignments Caution: DO NOT plug a phone jack connector into any RJ-45 port. Use only twisted-pair cables with RJ-45 connectors that conform with FCC standards. For 100BASE-TX/10BASE-T connections, a twisted-pair cable must have two pairs of wires. Each wire pair is identified by two different colors.
  • Page 57: Cables

    ABLES 100BASE-TX/10BASE-T Pin Assignments With 100BASE-TX/10BASE-T cable, pins 1 and 2 are used for transmitting data, and pins 3 and 6 for receiving data. RJ-45 Pin Assignments Pin Number Assignment 1: The “+” and “-” signs represent the polarity of the wires that make up each wire pair.
  • Page 58: Crossover Wiring

    ABLES Crossover Wiring If the twisted-pair cable is to join two ports and either both ports are labeled with an “x” (MDI-X) or neither port is labeled with an “x” (MDI), a crossover must be implemented in the wiring. Crossover RJ-45 Pin Assignments End 1 End 2 1 (Tx+)
  • Page 59: Console Port Pin Assignments

    ABLES Console Port Pin Assignments The DB-9 serial port on the switch’s rear panel is used to connect to the switch for out-of-band console configuration. The on-board menu-driven configuration program can be accessed from a terminal, a PC running a terminal emulation program, or from a remote location via a modem connection.
  • Page 60: Db-9 Port Pin Assignments

    ABLES DB-9 Port Pin Assignments CCITT Description Switch’s PC DB9 Modem Signal Circuit Signal DB9 DTE DB25 Direction Pin # Pin # DCE Pin # DTE-DCE DCD (Data Carrier Detected) 1 <------ RxD (Received Data) <------ TxD (Transmitted Data) ------> 108.2 DTR (Data Terminal Ready) ------>...
  • Page 61: Console Port To 25-Pin Dte Port On Pc

    ABLES Console Port to 25-Pin DTE Port on PC Switch’s 9-Pin Null Modem PC’s 25-Pin Serial Port DTE Port 1 DCD 8 DCD 2 RXD 3 TXD 3 TXD 2 RXD 4 DTR 20 DTR 5 SGND 7 SGND 6 DSR 6 DSR 7 RTS 4 RTS...
  • Page 62 ABLES...
  • Page 63: Specifications

    PPENDIX PECIFICATIONS Physical Characteristics Ports 12/24 10BASE-T/100BASE-TX, with auto-negotiation 1 slot for an optional dual-port 100BASE-FX or single-port 1000BASE-SX media expansion module 1 slot for a media expansion module or stacking module Network Interface 10BASE-T: RJ-45 (100-ohm, UTP cable; Categories 3, 4, 5) 100BASE-TX: RJ-45 (100-ohm, UTP cable;...
  • Page 64 PECIFICATIONS Switching Database 12K MAC address entries LEDs System: Power, RDP, Mgmt Port: Mode (flow control, full duplex, activity), Link (speed, link, disable/partition) Weight SMC6912M: 10.34 lbs (4.69 kg) SMC6924M: 10.63 lbs (4.82 kg) Size 17.37 x 11.22 x 2.53 in (44.0 x 28.5 x 6.4 cm) Temperature °...
  • Page 65: Switch Features

    PECIFICATIONS Switch Features Spanning Tree Protocol Forwarding Mode Store-and-forward Throughput Wire speed Flow Control Full Duplex: IEEE 802.3x Half Duplex: Back pressure Broadcast Storm Control Configurable threshold on a per-port basis. VLAN Support Up to 256 groups; port-based or with 802.1Q VLAN tagging, GVRP for automatic VLAN learning Multicast Switching IGMP Snooping...
  • Page 66: Management Features

    TFTP or Web (HTTP) in-band or XModem out-of-band MIB Support MIB II (RFC 1213), Bridge MIB (RFC 1493), Ethernet-Like MIB (RFC 1643), RMON MIB (RFC 1757), SMC’s private MIB RMON Support Groups 1, 2, 3, 9 (Statistics, History, Alarm, Event)
  • Page 67: Standards

    PECIFICATIONS Standards IEEE 802.3 Ethernet, IEEE 802.3u Fast Ethernet IEEE 802.3z Gigabit Ethernet IEEE 802.1D Spanning Tree Protocol and traffic priorities IEEE 802.1p priority tags, IEEE 802.1Q VLAN IEEE 802.3ac VLAN tagging IEEE 802.1Q VLAN Bridge Management IEEE 802.3x full-duplex flow control ISO/IEC 8802-3 SNMP (RFC 1157), RMON (RFC 1757), ARP (RFC 826), IGMP (RFC 1112), MIB II (RFC 1213), Interfaces Evolution MIB...
  • Page 68: Slide-In Module

    PECIFICATIONS Slide-in Module 100BASE-FX Extender Module Model SMC6900FSC, SMC6900FST Ports 2 100BASE-FX Network Interface SC connector, 50/125 or 62.5/125 micron multimode fiber cable (SMC6900FST includes SC-ST Converter) Standards 802.3u Fast Ethernet 1000BASE-SX Extender Module Model SMC6900G Ports 1 1000BASE-SX Network Interface SC connector, 50/125 or 62.5/125 micron multimode fiber cable Standards 802.3z Gigabit Ethernet...
  • Page 69: Stack Module

    PECIFICATIONS Stack Module Model SMC6900S Ports 2-Gbps uplink/downlink ports Connector Interface 68-pin SCSI connector, copper cable Standards 802.3z Gigabit Ethernet...
  • Page 70 PECIFICATIONS...
  • Page 71 PPENDIX RDERING NFORMATION TigerSwitch 10/100 Products and Accessories Product Number Description SMC6912M 12-port Fast Ethernet Switch with two media expansion slots SMC6924M 24-port Fast Ethernet Switch with two media expansion slots SMC6900S Stacking Module with 2-Gbps uplink/ downlink ports SMC6900FSC Fiber Module with two 100BASE-FX Port (SC-type Connector) SMC6900FST...
  • Page 72: Ordering Information

    RDERING NFORMATION...
  • Page 73: Glossary

    LOSSARY 10BASE-T IEEE 802.3 specification for 10 Mbps Ethernet over two pairs of Category 3, 4, or 5 UTP cable. 100BASE-FX IEEE 802.3u specification for 100 Mbps Fast Ethernet over two strands of 50/125 or 62.5/125 micron core fiber cable. 100BASE-TX IEEE 802.3u specification for 100 Mbps Fast Ethernet over two pairs of Category 5 UTP cable.
  • Page 74 LOSSARY Class I Repeater Fast Ethernet repeater that is principally used to connect different physical signaling systems (e.g., 100BASE-TX, 100BASE-FX) and that has an internal delay such that only one repeater of this type can reside within a single collision domain when maximum cable lengths are used.
  • Page 75 LOSSARY Ethernet A network communication system developed and standardized by DEC, Intel, and Xerox, using baseband transmission, CSMA/CD access, logical bus topology, and coaxial cable. The successor IEEE 802.3 standard provides for integration into the OSI model and extends the physical layer and media with repeaters and implementations that operate on fiber, thin coax and twisted-pair cable.
  • Page 76 LOSSARY IEEE 802.3u Defines CSMA/CD access method and physical layer specifications for 100BASE-TX Fast Ethernet. IEEE 802.3x Defines Ethernet frame start/stop requests and timers used for flow control on full-duplex links. IEEE 802.3z Defines CSMA/CD access method and physical layer specifications for 1000BASE Gigabit Ethernet.
  • Page 77 LOSSARY An acronym for Management Information Base. It is a set of database objects that contains information about the device. Media Independent Interface, the standard interface for Fast Ethernet—similar to the AUI interface for traditional Ethernet. Network Diameter Wire distance between two end stations in the same collision domain.
  • Page 78 LOSSARY Glossary-6...
  • Page 79: Index

    NDEX Numerics 10 Mbps connectivity rules 2-8 cable 100 Mbps connectivity rules 2-7 lengths 2-6 1000 Mbps connectivity rules 2-6 specifications B-1 1000BASE-SX CE Mark i connections 4-5 cleaning fiber terminators 4-5 fiber cable lengths 2-6 compliances i modules 1-8 EMC C-5 100BASE cable lengths 2-7 safety C-5...
  • Page 80 NDEX FCC compliance i Mgmt 1-4 features C-3 problems A-1 management 1-11 PWR 1-4 switch 1-10 RDP 1-4 fiber cables 4-5 Status 1-5 flow control, IEEE 802.3x 1-3 limited warranty C-5 front panel of switch 1-1 location requirements 3-1 full-duplex connectivity 2-1 management Gigabit Ethernet cable lengths 2-6 agent 1-3...
  • Page 81 NDEX RPU 1-8 connecting 3-8 optional installing in a rack 3-5 modules 1-2 installing on a desktop 3-5 modules, installation 3-3 RS-232 port 1-5 optional equipment D-1 rubber foot pads, attaching 3-5 ordering information D-1 out-of-band management 1-3 safety compliance iii sample applications 2-2 package contents 3-2 SC port connections 4-5...
  • Page 82 NDEX troubleshooting in-band access A-2 power and cooling problems A-2 switch indicators A-1 twisted-pair connections 4-1 UL compliance iii VCCI compliance ii VLANs 1-5 tagging 2-5 warranty C-5 Web-based management 1-3 Weighted Fair Queuing 1-7 Index-4...
  • Page 84 FOR TECHNICAL SUPPORT, CALL: From U.S.A. and Canada (8:30 AM - 8:00 PM Pacific Time) (800) SMC-4-YOU; (949) 707-2400; (949) 707-2460 (Fax) From Europe (8:00 AM - 5:30 PM UK Greenwich Mean Time) 44 (0) 1189 748740; 44 (0) 1189 748741 (Fax)

Table of Contents