Related Manuals for SMC Networks 6152PL2 - annexe 1
Summary of Contents for SMC Networks 6152PL2 - annexe 1
-
Page 1: Installation Guide
INSTALLATION GUIDE SMC6128PL2 TigerSwitchTM 10/100 24-Port 10/100 Switch with PoE, SMC6152PL2 IP Clustering and 4 Gigabit Ports... - Page 3 TigerSwitch 10/100 Installation Guide From SMC's Tiger line of feature-rich workgroup LAN solutions 20 Mason April 2009 Pub. # 149100000007A Irvine, CA 92618 E042009-MW-R01 Phone: (949) 679-8000...
- Page 4 No license is granted by implication or otherwise under any patent or patent rights of SMC. SMC reserves the right to change specifications at any time without notice.
- Page 5 Warranty and Product Registration To register SMC products and to review the detailed warranty statement, please refer to the Support Section of the SMC Website at http://www.smc.com.
-
Page 7: Japan Vcci Class A
Compliances and Safety Warnings FCC - Class A This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. - Page 8 CE Mark Declaration of Conformance for EMI and Safety (EEC) This information technology equipment complies with the requirements of the Council Directive 89/336/EEC on the Approximation of the laws of the Member States relating to Electromagnetic Compatibility and 73/23/EEC for electrical equipment used within certain voltage limits and the Amendment Directive 93/68/EEC.
-
Page 9: Safety Compliance
Safety Compliance Warning: Fiber Optic Port Safety When using a fiber optic port, never look at the transmit laser while it is powered on. Also, never look directly at the fiber TX port and fiber cable CLASS I LASER DEVICE ends when they are powered on. - Page 10 Important!Before making connections, make sure you have the correct cord set. Check it (read the label on the cable) against the following: Power Cord Set U.S.A. and Canada The cord set must be UL-approved and CSA certified. The minimum specifications for the flexible cord are: - No.
- Page 11 France et Pérou uniquement: Ce groupe ne peut pas être alimenté par un dispositif à impédance à la terre. Si vos alimentations sont du type impédance à la terre, ce groupe doit être alimenté par une tension de 230 V (2 P+T) par le biais d’un transformateur d’isolement à rapport 1:1, avec un point secondaire de connexion portant l’appellation Neutre et avec raccordement direct à...
-
Page 12: Warnings And Cautionary Messages
Stromkabel . Dies muss von dem Land, in dem es benutzt wird geprüft werden: Schweiz Dieser Stromstecker muß die SEV/ASE 1011Bestimmungen einhalt- Europe Das Netzkabel muß vom Typ HO3VVF3GO.75 (Mindestanforderung) sein und die Aufschrift <HAR> oder <BASEC> tragen. Der Netzstecker muß die Norm CEE 7/7 erfüllen (”SCHUKO”). Warnings and Cautionary Messages Warning: This product does not contain any serviceable user parts. -
Page 13: Manufacturing Materials
Environmental Statement The manufacturer of this product endeavours to sustain an environmentally-friendly policy throughout the entire production process. This is achieved though the following means: • Adherence to national legislation and regulations on environmental production standards. • Conservation of operational resources. •... -
Page 14: About This Guide
Added information for SMC6152PL2 model. September 2007 Revision This is the second revision of this guide. It includes the following changes: • Updated safety certification to remove TUV/GS information. • Updated SMC address. February 2007 Revision This is the first revision of this guide. -
Page 15: Table Of Contents
Contents Chapter 1: Introduction Overview Switch Architecture Power-over-Ethernet Capability Network Management Options Description of Hardware 10/100BASE-T Ports Gigabit Combination Ports Port and System Status LEDs Power Supply Socket Features and Benefits Connectivity Expandability Performance Management Chapter 2: Network Planning Introduction to Switching Application Examples Supplying PoE Collapsed Backbone... - Page 16 Contents Connecting to the Console Port Wiring Map for Serial Cable Chapter 4: Making Network Connections Connecting Network Devices Twisted-Pair Devices Power-over-Ethernet Connections Cabling Guidelines Connecting to PCs, Servers, Hubs and Switches Network Wiring Connections Fiber Optic SFP Devices Connectivity Rules 1000BASE-T Cable Requirements 1000 Mbps Gigabit Ethernet Collision Domain 100 Mbps Fast Ethernet Collision Domain...
- Page 17 Tables Table 1-2 SMC6152PL2 Port and System Status LEDs Table 1-1 SMC6128PL2 Port and System Status LEDs Table 3-1. Serial Cable Wiring Table 4-1 Maximum 1000BASE-T Gigabit Ethernet Cable Length Table 4-2 Maximum 1000BASE-SX Gigabit Ethernet Cable Length Table 4-3 Maximum 1000BASE-LX Gigabit Ethernet Cable Length Table 4-4 Maximum 1000BASE-ZX Gigabit Ethernet Cable Length...
- Page 18 Figures Figure 1-1 SMC6128PL2 Panels Figure 1-2 SMC6152PL2 Panels Figure 1-3 Port and System Status LEDs Figure 1-4 Power Supply Socket Figure 2-1 PoE Connections Figure 2-2 Collapsed Backbone Figure 2-3 Network Aggregation Plan Figure 2-4 Remote Connection with Fiber Cable Figure 2-5 Making VLAN Connections Figure 3-1...
-
Page 19: Chapter 1: Introduction
Chapter 1: Introduction Overview The SMC6128PL2 and SMC6152PL2 are intelligent PoE switches with 24/48 10/ 100BASE-T ports, two 10/100/1000BASE-T ports, and two Gigabit combination ports that are comprised of an RJ-45 port and an SFP transceiver slot. There is also an SNMP-based management agent embedded on the main board. This agent supports both in-band and out-of-band access for managing the switch. -
Page 20: Switch Architecture
Introduction Switch Architecture These switches employ a wire-speed, non-blocking switching fabric. This permits simultaneous wire-speed transport of multiple packets at low latency on all ports. These switches also features full-duplex capability on all ports, which effectively doubles the bandwidth of each connection. hese switches use store-and-forward switching to ensure maximum data integrity. -
Page 21: Description Of Hardware
Description of Hardware Description of Hardware 10/100BASE-T Ports These switches contain 24/48 10BASE-T/100BASE-TX RJ-45 ports. These ports support automatic MDI/MDI-X operation, so you can use straight-through cables for all network connections to PCs or servers, or to other switches or hubs. (See “10BASE-T/100BASE-TX Pin Assignments”... -
Page 22: Table 1-2 Smc6152Pl2 Port And System Status Leds
Introduction Table 1-1 SMC6128PL2 Port and System Status LEDs Condition Status Fast Ethernet RJ-45 Ports Link/Activity On/Blinking The port has a valid 100 Mbps link. Green Blinking indicates activity. On/Blinking The port has a valid 10 Mbps link. Amber Blinking indicates activity. There is no valid link on the port. -
Page 23: Power Supply Socket
Description of Hardware Power Supply Socket There is one standard power socket on the rear panel for the AC power cord. Power Socket SMC6128PL2 R A T IN G 1 0 0 ~ 2 4 0 V - 3 A 50 ~ 6 0 H Z SMC6152PL2 Figure 1-4 Power Supply Socket... -
Page 24: Features And Benefits
Introduction Features and Benefits Connectivity • 24/48 10/100BASE-T ports, 2 Gigabit 1000BASE-T ports, and 4 Gigabit combination ports (RJ-45/SFP). • Auto-negotiation enables each RJ-45 port to automatically select the optimum speed (10/100/1000 Mbps), and the communication mode (half or full duplex) if this feature is supported by the attached device;... -
Page 25: Chapter 2: Network Planning
Chapter 2: Network Planning Introduction to Switching A network switch allows simultaneous transmission of multiple packets via non-crossbar switching. This means that it can partition a network more efficiently than bridges or routers. The switch has, therefore, been recognized as one of the most important building blocks for today’s networking technology. -
Page 26: Application Examples
Network Planning Application Examples These switches are not only designed to segment your network, but also to provide a wide range of options in setting up network connections. Some typical applications are described in the following pages. Supplying PoE These switches are an excellent choice for supplying power to connected PoE devices such as web cameras, IP telephones or access points. -
Page 27: Collapsed Backbone
Application Examples Collapsed Backbone These switches are an excellent choice for mixed Ethernet, Fast Ethernet, and Gigabit Ethernet installations where significant growth is expected in the near future. In a basic stand-alone configuration, it can provide direct full-duplex connections to workstations or servers. -
Page 28: Network Aggregation Plan
Network Planning Network Aggregation Plan With 24/8 parallel bridging ports (i.e., 24 or 48 distinct collision domains), these switches can collapse a complex network down into a single efficient bridged node, increasing overall bandwidth and throughput. In the figure below, the 10/100BASE-TX ports on the switch are providing 100 Mbps connectivity through layer 2 switches. -
Page 29: Remote Connection With Fiber Cable
Application Examples Remote Connection with Fiber Cable Fiber optic technology allows for longer cabling than any other media type. A 1000BASE-SX (MMF) link can connect to a site up to 550 meters away, a 1000BASE-LX (SMF) link up to 5 km, and a 1000BASE-ZX link up to 100 km. This allows the switch to serve as a collapsed backbone, providing direct connectivity for a widespread LAN. -
Page 30: Making Vlan Connections
Network Planning Making VLAN Connections These switches support VLANs which can be used to organize any group of network nodes into separate broadcast domains. VLANs confine broadcast traffic to the originating group, and can eliminate broadcast storms in large networks. This provides a more secure and cleaner network environment. -
Page 31: Application Notes
Application Notes Application Notes Full-duplex operation only applies to point-to-point access (such as when a switch is attached to a workstation, server or another switch). When the switch is connected to a hub, both devices must operate in half-duplex mode. Avoid using flow control on a port connected to a hub unless it is actually required to solve a problem. - Page 32 Network Planning...
-
Page 33: Chapter 3: Installing The Switch
Chapter 3: Installing the Switch Selecting a Site Switch units can be mounted in a standard 19-inch equipment rack or on a flat surface. Be sure to follow the guidelines below when choosing a location. • The site should: - be at the center of all the devices you want to link and near a power outlet. - be able to maintain its temperature within 0 to 45 °C (32 to 113 °F) and its humidity within 10% to 90%, non-condensing - provide adequate space (approximately two inches) on all sides for proper air... -
Page 34: Equipment Checklist
Installing the Switch RJ-45 Connector Figure 3-1 RJ-45 Connections Equipment Checklist After unpacking the switch, check the contents to be sure you have received all the components. Then, before beginning the installation, be sure you have all other necessary installation equipment. Package Contents •... -
Page 35: Mounting
Mounting Mounting The switch units can be mounted in a standard 19-inch equipment rack or on a desktop or shelf. Mounting instructions for each type of site follow. Rack Mounting Before rack mounting the switch, pay particular attention to the following factors: •... -
Page 36: Desktop Or Shelf Mounting
Installing the Switch Mount the device in the rack, using four rack-mounting screws (not provided). T ig e rS w it c h 1 0 /1 0 Figure 3-3 Installing the Switch in a Rack If installing a single switch only, turn to “Connecting to a Power Source” at the end of this chapter. -
Page 37: Installing An Optional Sfp Transceiver
Installing an Optional SFP Transceiver Installing an Optional SFP Transceiver T ig e r S w it c h 1 0 /1 0 Figure 3-5 Inserting an SFP Transceiver into a Slot The switch supports 1000BASE-SX, 1000BASE-LX and 1000BASE-ZX SFP transceivers. -
Page 38: Connecting To A Power Source
Installing the Switch Connecting to a Power Source To connect a device to a power source: Insert the power cable plug directly into the socket located at the back of the device. SMC6128PL2 R A T IN G 1 0 0 ~ 2 4 0 V - 3 A 50 ~ 6 0 H Z SMC6152PL2 Figure 3-6 Power Socket... -
Page 39: Wiring Map For Serial Cable
Connecting to the Console Port Wiring Map for Serial Cable Table 3-1. Serial Cable Wiring Switch’s 9-Pin Null Modem PC’s 9-Pin Serial Port DTE Port 2 RXD (receive data) <---------------------------- 3 TXD (transmit data) 3 TXD (transmit data) -----------------------------> 2 RXD (receive data) 5 SGND (signal ground) ------------------------------ 5 SGND (signal ground) No other pins are used. - Page 40 Installing the Switch...
-
Page 41: Chapter 4: Making Network Connections
Chapter 4: Making Network Connections Connecting Network Devices These switches are designed to interconnect multiple segments (or collision domains). They can be connected to network cards in PCs and servers, as well as to hubs, switches or routers. They may also be connected to devices using optional SFP tranceivers. -
Page 42: Cabling Guidelines
Making Network Connections Cabling Guidelines The RJ-45 ports on the switch supports automatic MDI/MDI-X pinout configuration, so you can use standard straight-through twisted-pair cables to connect to any other network device (PCs, servers, switches, routers, or hubs). See Appendix B for further information on cabling. Caution: Do not plug a phone jack connector into an RJ-45 port. -
Page 43: Network Wiring Connections
Twisted-Pair Devices Network Wiring Connections Today, the punch-down block is an integral part of many of the newer equipment racks. It is actually part of the patch panel. Instructions for making connections in the wiring closet with this type of equipment follows. Attach one end of a patch cable to an available port on the switch, and the other end to the patch panel. -
Page 44: Fiber Optic Sfp Devices
Making Network Connections Fiber Optic SFP Devices An optional Gigabit SFP transceiver (1000BASE-SX, 1000BASE-LX, or 1000BASE-ZX) can be used for a backbone connection between switches, or for connecting to a high-speed server. Each multimode fiber optic port requires 50/125 or 62.5/125 micron multimode fiber optic cabling with an LC connector at both ends. -
Page 45: Connectivity Rules
Connectivity Rules The 1000BASE-SX, 1000BASE-LX and 1000BASE-ZX fiber optic ports operate at 1 Gbps full duplex, with auto-negotiation of flow control. The maximum length for fiber optic cable operating at Gigabit speed will depend on the fiber type as listed under “1000 Mbps Gigabit Ethernet Collision Domain”... -
Page 46: 100 Mbps Fast Ethernet Collision Domain
Making Network Connections Table 4-4 Maximum 1000BASE-ZX Gigabit Ethernet Cable Length Fiber Size Fiber Bandwidth Maximum Cable Length Connector 9/125 micron 70 m - 100 km (43 ft - 62 single-mode fiber miles) Note: For link spans exceeding 70 km, you may need to use premium single mode fiber or dispersion shifted single mode fiber. -
Page 47: Appendix A: Troubleshooting
Appendix A: Troubleshooting Diagnosing Switch Indicators Table A-1 Troubleshooting Chart Symptom Action PWR/System LED is Off • Power supply is disconnected. • Check connections between the switch, the power cord, and the wall outlet. • Contact your dealer for assistance. PWR/System LED is Amber •... -
Page 48: In-Band Access
Troubleshooting In-Band Access You can access the management agent in the switch from anywhere within the attached network using Telnet, a Web browser, or other network management software tools. However, you must first configure the switch with a valid IP address, subnet mask, and default gateway. -
Page 49: Appendix B: Cables
Appendix B: Cables Twisted-Pair Cable and Pin Assignments For 10/100BASE-TX connections, a twisted-pair cable must have two pairs of wires. For 1000BASE-T connections the twisted-pair cable must have four pairs of wires. Each wire pair is identified by two different colors. For example, one wire might be green and the other, green with white stripes. -
Page 50: Straight-Through Wiring
Cables Table B-1 10/100BASE-TX MDI and MDI-X Port Pinouts MDI Signal Name MDI-X Signal Name Receive Data plus (RD+) Transmit Data plus (TD+) and GND (Positive V and -48V feeding power (Negative V port port Receive Data minus (RD-) and Transmit Data minus (TD-) and GND (Positive V and -48V feeding power (Negative V... -
Page 51: Crossover Wiring
Twisted-Pair Cable and Pin Assignments Crossover Wiring If the twisted-pair cable is to join two ports and either both ports are labeled with an “X” (MDI-X) or neither port is labeled with an “X” (MDI), a crossover must be implemented in the wiring. (When auto-negotiation is enabled for any RJ-45 port on this switch, you can use either straight-through or crossover cable to connect to any device type.) You must connect all four wire pairs as shown in the following diagram to support... - Page 52 Cables Table B-2 1000BASE-T MDI and MDI-X Port Pinouts (Continued) MDI Signal Name MDI-X Signal Name Bi-directional Data Two Minus (BI_D2-) Bi-directional Data One Minus (BI_D1-) Bi-directional Data Four Plus (BI_D4+) Bi-directional Data Three Plus (BI_D3+) Bi-directional Data Four Minus (BI_D4-) Bi-directional Data Three Minus (BI_D3-) Cable Testing for Existing Category 5 Cable Installed Category 5 cabling must pass tests for Attenuation, Near-End Crosstalk...
-
Page 53: Physical Characteristics
Appendix C: Specifications Physical Characteristics Ports 24/48 10/100BASE-TX, with auto-negotiation 2 10/100/1000BASE-T Ports 2 Combination Gigabit Ports (RJ-45/SFP) Network Interface Ports 1-24/48: RJ-45 connector, auto MDI/X 10BASE-T: RJ-45 (100-ohm, UTP cable; Category 3 or better) 100BASE-TX: RJ-45 (100-ohm, UTP cable; Category 5 or better) Ports 25-28/49-52: RJ-45 connector, auto MDI/X 1000BASE-T: RJ-45 (100-ohm, UTP cable;... -
Page 54: Switch Features
Specifications Temperature SMC6128PL2 Operating: 0 to 45 °C (32 to 113 °F) Storage: -40 to 70 °C (-40 to 158 °F) SMC6152PL2 Operating: 0 to 45 °C (32 to 113 °F) Storage: -40 to 70 °C (-40 to 158 °F) Humidity Operating: 10% to 90% (non-condensing) Power Supply... -
Page 55: Management Features
Management Features Management Features In-Band Management Telnet, HTTP or SNMP manager Out-of-Band Management RS-232 DB-9 console port Software Loading TFTP in-band, or XModem out-of-band Standards IEEE 802.3 Ethernet IEEE 802.3u Fast Ethernet IEEE 802.3z and 802.3ab Gigabit Ethernet IEEE 802.3af Power over Ethernet IEEE 802.1D (Bridging) IEEE 802.3x full-duplex flow control IEEE 802.1Q (Virtual LAN) - Page 56 Specifications...
-
Page 57: Glossary
Glossary 10BASE-T IEEE 802.3 specification for 10 Mbps Ethernet over two pairs of Category 3, 4, or 5 UTP cable. 100BASE-TX IEEE 802.3u specification for 100 Mbps Ethernet over two pairs of Category 5 UTP cable. 1000BASE-LX Specification for long-haul Gigabit Ethernet over two strands of 50/125, 62.5/125 or 9/125 micron core fiber cable. - Page 58 Glossary CSMA/CD CSMA/CD (Carrier Sense Multiple Access/Collision Detect) is the communication method employed by Ethernet, Fast Ethernet, or Gigabit Ethernet. End Station A workstation, server, or other device that does not forward traffic. Ethernet A network communication system developed and standardized by DEC, Intel, and Xerox, using baseband transmission, CSMA/CD access, logical bus topology, and coaxial cable.
- Page 59 Glossary IEEE 802.3af (PoE) An IEEE standard for providing Power over Ethernet (PoE) capabilities. When Ethernet is passed over copper cable, two twisted pairs are used for data transfer, and two twisted pairs are unused. With PoE, power can either be passed over the two data pairs or over the two spare pairs.
- Page 60 Glossary RJ-45 Connector A connector for twisted-pair wiring. Switched Ports Ports that are on separate collision domains or LAN segments. Telecommunications Industry Association Transmission Control Protocol/Internet Protocol (TCP/IP) Protocol suite that includes TCP as the primary transport protocol, and IP as the network layer protocol.
-
Page 61: Index
Index Numerics 10 Mbps connectivity rules 4-6 desktop mounting 3-4 100 Mbps connectivity rules 4-6 device connections 4-1 1000 Mbps connectivity rules 4-5 1000BASE-T pin assignments B-3 electrical interference, avoiding 3-1 ports 1-3 equipment checklist 3-2 100BASE-TX Ethernet connectivity rules 4-6 pin assignments B-1 ports 1-3 10BASE-T... - Page 62 Index rear panel receptacle 1-5 RJ-45 port 1-3 management connections 4-1 agent 1-2 pinouts B-2, B-3 features 1-6, C-3 rubber foot pads, attaching 3-4 out-of-band 1-2 SNMP 1-2 Web-based 1-2 screws for rack mounting 3-2 mounting the switch SFP slots 1-3 in a rack 3-3 site selelction 3-1 on a desktop or shelf 3-4...
- Page 64 SMC6128PL2 SMC6152PL2 149100000007A R01...