English Important Safety Information Plug And Fuse Information Care and Cleaning Parts List 9-13 To Use Your Stand Mixer Usage Diagrams and Usage Instructions 9-11 11-12 Usage Chart Recipes To Use The Weighing Function To Assemble The Creaming Beater To Fit And Use Your Splashguard Tool Adjustment To Fit And Remove The Head Cover Service And Customer Care...
If the plug or cord is damaged it must, for safety reasons, be replaced by Kenwood or an authorised Kenwood repairer in order to avoid a hazard. Always turn the speed control to ‘O’ OFF position and unplug before fitting or removing tools/attachments, after use and before cleaning.
Page 5
The maximum rating is based on the mini chopper/mill attachment that draws the greatest load. Other attachments may draw less power. Only use the appliance for its intended domestic use. Kenwood will not accept any liability if the appliance is subject to improper use, or failure to comply with these instructions.
The correct fuse cover is identified by colour and a replacement may be obtained from your Kenwood Authorised Repairer (see Service). Plug Type G This appliance conforms to EC Regulation 1935/2004 on materials and articles intended to come into contact with food.
To Use Your Stand Mixer Usage Diagrams and Usage Instructions...
Page 11
Important Ensure that no bowl tools are fitted or stored in the bowl when using other outlets. Do not use the whisk for heavy mixtures (all in one cakes and creaming fat & sugar) as you could damage it. Never exceed the maximum capacities and speeds stated – you may overload the machine.
Other types of yeast: follow the manufacturer’s instructions. Put the dough into a greased polythene bag or a bowl covered with a tea towel. Then leave somewhere warm until doubled in size. Usage Chart (MAX) (Mins) KVC85 KVL85 3.5L Min–1 1–2 340 g...
Page 13
(MAX) (Mins) KVC85 KVL85 3.5L Min–Max 1.5–2 (210 g) (420 g) (280 g) (560 g) 0.35 L 0.5 L Min–Max 1.5–3 4-8˚C 620 g 930 g 620 g 930 g Min–Max 4–6 Min–Max 1–1.5 250 g 500 g 200 g 1–1.5...
Recipes Pizza Dough 500g Flour 30g Olive Oil 7g Salt 7g Yeast 300ml Water Fit the bowl to the stand mixer. All all of the ingredients. Fit the dough hook and lower the head. Mix on minimum speed for 1 minute. Knead on speed 1 for 4 minutes.
To Use the Weighing Function Usage Diagrams and Usage Instructions Important Always place the appliance on a dry, flat, stable surface prior to weighing. Do not apply pressure to the mixer or bowl whilst weighing as this will affect the accuracy of the scales.
To Assemble The Creaming Beater Usage Diagrams and Usage Instructions Important The wiper blade is supplied already fitted and should always be removed before cleaning. Carefully fit the flexible wiper blade onto the tool by locating the base of the wiper blade into the slot then fit one side into the groove before gently hooking the end in place.
To Fit and Use Your Splashguard Usage Diagrams and Usage Instructions Important During mixing, ingredients can be added directly to the bowl via the hinged section of the splashguard. You do not need to remove the splashguard to change tools. Raise the mixer head until it locks.
The tools are set to the correct height for the bowl supplied in the factory and should not require adjustment. However, if you wish to adjust the tool use a suitable sized spanner: TYPE KVC85 = 15mm TYPE KVL85 = 19mm Unplug the appliance.
To Fit and Remove Head Cover Usage Diagrams and Usage Instructions Remove the slow speed and high speed outlet covers. With the retention clip pressed in, lift up the head cover and slide forward. To fit an alternative head cover, insert the pegs on the end of the head cap into the two holes on the slow speed outlet.
(in or out of guarantee) call Kenwood customer care on 0345 222 0458. Have your model number (e.g. TYPE KVC85/KVL85) and date code (5 digit code e.g. 24T04) ready. They are on the underside of the power unit.
Troubleshooting Guide Problem Cause Solution The whisk, K-Beater Tool at the wrong height Adjust the height using a suitable knocks against the and needs adjusting. spanner – see “Tool Adjustment” bottom of the bowl section. or not reaching the ingredients in the bottom of the bowl.
Page 22
Problem Cause Solution Weighing Function Display screen freezes The display screen will Normal operation. on [- - - -] freeze during operation. Display screen showing Either zero the screen or replace a minus reading due to the missing ingredients or refit the display not ‘zeroed’...
Need help?
Do you have a question about the KVC85 and is the answer not in the manual?
Questions and answers